This repository has been archived on 2022-01-28. You can view files and clone it, but cannot push or open issues or pull requests.
Marlin-Artillery-M600/Marlin/configuration_store.cpp

904 lines
27 KiB
C++
Raw Normal View History

/**
2015-04-26 06:04:54 +02:00
* configuration_store.cpp
*
* Configuration and EEPROM storage
*
2015-04-04 01:38:05 +02:00
* IMPORTANT: Whenever there are changes made to the variables stored in EEPROM
* in the functions below, also increment the version number. This makes sure that
* the default values are used whenever there is a change to the data, to prevent
* wrong data being written to the variables.
*
* ALSO: Variables in the Store and Retrieve sections must be in the same order.
* If a feature is disabled, some data must still be written that, when read,
* either sets a Sane Default, or results in No Change to the existing value.
*
*/
2015-08-31 04:04:30 +02:00
#define EEPROM_VERSION "V21"
2015-04-04 01:38:05 +02:00
/**
* V21 EEPROM Layout:
*
* 100 Version (char x4)
*
* 104 M92 XYZE axis_steps_per_unit (float x4)
* 120 M203 XYZE max_feedrate (float x4)
* 136 M201 XYZE max_acceleration_units_per_sq_second (uint32_t x4)
* 152 M204 P acceleration (float)
* 156 M204 R retract_acceleration (float)
* 160 M204 T travel_acceleration (float)
* 164 M205 S minimumfeedrate (float)
* 168 M205 T mintravelfeedrate (float)
* 172 M205 B minsegmenttime (ulong)
* 176 M205 X max_xy_jerk (float)
* 180 M205 Z max_z_jerk (float)
* 184 M205 E max_e_jerk (float)
* 188 M206 XYZ home_offset (float x3)
*
2015-03-15 23:18:11 +01:00
* Mesh bed leveling:
* 200 M420 S active (bool)
* 201 mesh_num_x (uint8 as set in firmware)
* 202 mesh_num_y (uint8 as set in firmware)
* 203 M421 XYZ z_values[][] (float x9, by default)
* 239 M851 zprobe_zoffset (float)
2015-03-15 23:18:11 +01:00
*
* DELTA:
* 243 M666 XYZ endstop_adj (float x3)
* 255 M665 R delta_radius (float)
* 259 M665 L delta_diagonal_rod (float)
* 263 M665 S delta_segments_per_second (float)
*
* Z_DUAL_ENDSTOPS:
* 267 M666 Z z_endstop_adj (float)
*
* ULTIPANEL:
* 271 M145 S0 H plaPreheatHotendTemp (int)
* 273 M145 S0 B plaPreheatHPBTemp (int)
* 275 M145 S0 F plaPreheatFanSpeed (int)
* 277 M145 S1 H absPreheatHotendTemp (int)
* 279 M145 S1 B absPreheatHPBTemp (int)
* 281 M145 S1 F absPreheatFanSpeed (int)
*
* PIDTEMP:
* 283 M301 E0 PIDC Kp[0], Ki[0], Kd[0], Kc[0] (float x4)
* 299 M301 E1 PIDC Kp[1], Ki[1], Kd[1], Kc[1] (float x4)
* 315 M301 E2 PIDC Kp[2], Ki[2], Kd[2], Kc[2] (float x4)
* 331 M301 E3 PIDC Kp[3], Ki[3], Kd[3], Kc[3] (float x4)
* 347 M301 L lpq_len (int)
*
2015-04-04 01:38:05 +02:00
* PIDTEMPBED:
* 349 M304 PID bedKp, bedKi, bedKd (float x3)
2015-04-04 01:38:05 +02:00
*
* DOGLCD:
* 361 M250 C lcd_contrast (int)
*
* SCARA:
* 363 M365 XYZ axis_scaling (float x3)
*
* FWRETRACT:
* 375 M209 S autoretract_enabled (bool)
* 376 M207 S retract_length (float)
* 380 M207 W retract_length_swap (float)
* 384 M207 F retract_feedrate (float)
* 388 M207 Z retract_zlift (float)
* 392 M208 S retract_recover_length (float)
* 396 M208 W retract_recover_length_swap (float)
* 400 M208 F retract_recover_feedrate (float)
*
* Volumetric Extrusion:
* 404 M200 D volumetric_enabled (bool)
* 405 M200 T D filament_size (float x4) (T0..3)
*
* 421 This Slot is Available!
*
*/
#include "Marlin.h"
#include "language.h"
#include "planner.h"
#include "temperature.h"
#include "ultralcd.h"
2015-04-26 06:04:54 +02:00
#include "configuration_store.h"
#if ENABLED(MESH_BED_LEVELING)
#include "mesh_bed_leveling.h"
#endif
2015-03-15 23:18:11 +01:00
void _EEPROM_writeData(int &pos, uint8_t* value, uint8_t size) {
uint8_t c;
while (size--) {
eeprom_write_byte((unsigned char*)pos, *value);
2015-01-29 07:27:15 +01:00
c = eeprom_read_byte((unsigned char*)pos);
if (c != *value) {
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM(MSG_ERR_EEPROM_WRITE);
}
pos++;
value++;
};
}
void _EEPROM_readData(int &pos, uint8_t* value, uint8_t size) {
do {
*value = eeprom_read_byte((unsigned char*)pos);
pos++;
value++;
} while (--size);
}
#define EEPROM_WRITE_VAR(pos, value) _EEPROM_writeData(pos, (uint8_t*)&value, sizeof(value))
#define EEPROM_READ_VAR(pos, value) _EEPROM_readData(pos, (uint8_t*)&value, sizeof(value))
/**
* Store Configuration Settings - M500
*/
#define DUMMY_PID_VALUE 3000.0f
#define EEPROM_OFFSET 100
#if ENABLED(EEPROM_SETTINGS)
/**
* Store Configuration Settings - M500
*/
void Config_StoreSettings() {
float dummy = 0.0f;
char ver[4] = "000";
int i = EEPROM_OFFSET;
EEPROM_WRITE_VAR(i, ver); // invalidate data first
EEPROM_WRITE_VAR(i, axis_steps_per_unit);
EEPROM_WRITE_VAR(i, max_feedrate);
EEPROM_WRITE_VAR(i, max_acceleration_units_per_sq_second);
EEPROM_WRITE_VAR(i, acceleration);
EEPROM_WRITE_VAR(i, retract_acceleration);
EEPROM_WRITE_VAR(i, travel_acceleration);
EEPROM_WRITE_VAR(i, minimumfeedrate);
EEPROM_WRITE_VAR(i, mintravelfeedrate);
EEPROM_WRITE_VAR(i, minsegmenttime);
EEPROM_WRITE_VAR(i, max_xy_jerk);
EEPROM_WRITE_VAR(i, max_z_jerk);
EEPROM_WRITE_VAR(i, max_e_jerk);
EEPROM_WRITE_VAR(i, home_offset);
uint8_t mesh_num_x = 3;
uint8_t mesh_num_y = 3;
#if ENABLED(MESH_BED_LEVELING)
// Compile time test that sizeof(mbl.z_values) is as expected
2016-03-13 07:38:55 +01:00
typedef char c_assert[(sizeof(mbl.z_values) == (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS) * sizeof(dummy)) ? 1 : -1];
mesh_num_x = MESH_NUM_X_POINTS;
mesh_num_y = MESH_NUM_Y_POINTS;
2015-03-15 23:18:11 +01:00
EEPROM_WRITE_VAR(i, mbl.active);
EEPROM_WRITE_VAR(i, mesh_num_x);
EEPROM_WRITE_VAR(i, mesh_num_y);
2015-03-15 23:18:11 +01:00
EEPROM_WRITE_VAR(i, mbl.z_values);
#else
uint8_t dummy_uint8 = 0;
EEPROM_WRITE_VAR(i, dummy_uint8);
EEPROM_WRITE_VAR(i, mesh_num_x);
EEPROM_WRITE_VAR(i, mesh_num_y);
dummy = 0.0f;
for (uint8_t q = 0; q < mesh_num_x * mesh_num_y; q++) EEPROM_WRITE_VAR(i, dummy);
#endif // MESH_BED_LEVELING
#if DISABLED(AUTO_BED_LEVELING_FEATURE)
float zprobe_zoffset = 0;
#endif
EEPROM_WRITE_VAR(i, zprobe_zoffset);
2015-03-15 23:18:11 +01:00
#if ENABLED(DELTA)
EEPROM_WRITE_VAR(i, endstop_adj); // 3 floats
EEPROM_WRITE_VAR(i, delta_radius); // 1 float
EEPROM_WRITE_VAR(i, delta_diagonal_rod); // 1 float
EEPROM_WRITE_VAR(i, delta_segments_per_second); // 1 float
#elif ENABLED(Z_DUAL_ENDSTOPS)
EEPROM_WRITE_VAR(i, z_endstop_adj); // 1 floats
dummy = 0.0f;
for (uint8_t q = 5; q--;) EEPROM_WRITE_VAR(i, dummy);
#else
dummy = 0.0f;
for (uint8_t q = 6; q--;) EEPROM_WRITE_VAR(i, dummy);
#endif
#if DISABLED(ULTIPANEL)
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED,
absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
#endif // !ULTIPANEL
EEPROM_WRITE_VAR(i, plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i, plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i, plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i, absPreheatHotendTemp);
EEPROM_WRITE_VAR(i, absPreheatHPBTemp);
EEPROM_WRITE_VAR(i, absPreheatFanSpeed);
for (uint8_t e = 0; e < 4; e++) {
#if ENABLED(PIDTEMP)
if (e < EXTRUDERS) {
EEPROM_WRITE_VAR(i, PID_PARAM(Kp, e));
EEPROM_WRITE_VAR(i, PID_PARAM(Ki, e));
EEPROM_WRITE_VAR(i, PID_PARAM(Kd, e));
#if ENABLED(PID_ADD_EXTRUSION_RATE)
EEPROM_WRITE_VAR(i, PID_PARAM(Kc, e));
#else
dummy = 1.0f; // 1.0 = default kc
2015-02-06 23:43:58 +01:00
EEPROM_WRITE_VAR(i, dummy);
#endif
}
2015-04-04 01:38:05 +02:00
else
#endif // !PIDTEMP
2015-04-04 01:38:05 +02:00
{
dummy = DUMMY_PID_VALUE; // When read, will not change the existing value
EEPROM_WRITE_VAR(i, dummy);
dummy = 0.0f;
for (uint8_t q = 3; q--;) EEPROM_WRITE_VAR(i, dummy);
}
} // Extruders Loop
2015-08-31 04:04:30 +02:00
#if DISABLED(PID_ADD_EXTRUSION_RATE)
int lpq_len = 20;
#endif
EEPROM_WRITE_VAR(i, lpq_len);
#if DISABLED(PIDTEMPBED)
2015-04-04 01:38:05 +02:00
float bedKp = DUMMY_PID_VALUE, bedKi = DUMMY_PID_VALUE, bedKd = DUMMY_PID_VALUE;
#endif
EEPROM_WRITE_VAR(i, bedKp);
EEPROM_WRITE_VAR(i, bedKi);
EEPROM_WRITE_VAR(i, bedKd);
#if DISABLED(HAS_LCD_CONTRAST)
const int lcd_contrast = 32;
#endif
EEPROM_WRITE_VAR(i, lcd_contrast);
#if ENABLED(SCARA)
EEPROM_WRITE_VAR(i, axis_scaling); // 3 floats
#else
dummy = 1.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
#if ENABLED(FWRETRACT)
EEPROM_WRITE_VAR(i, autoretract_enabled);
EEPROM_WRITE_VAR(i, retract_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i, retract_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
EEPROM_WRITE_VAR(i, retract_feedrate);
EEPROM_WRITE_VAR(i, retract_zlift);
EEPROM_WRITE_VAR(i, retract_recover_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i, retract_recover_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
EEPROM_WRITE_VAR(i, retract_recover_feedrate);
#endif // FWRETRACT
EEPROM_WRITE_VAR(i, volumetric_enabled);
// Save filament sizes
for (uint8_t q = 0; q < 4; q++) {
if (q < EXTRUDERS) dummy = filament_size[q];
EEPROM_WRITE_VAR(i, dummy);
}
char ver2[4] = EEPROM_VERSION;
int j = EEPROM_OFFSET;
EEPROM_WRITE_VAR(j, ver2); // validate data
// Report storage size
SERIAL_ECHO_START;
SERIAL_ECHOPAIR("Settings Stored (", (unsigned long)i);
SERIAL_ECHOLNPGM(" bytes)");
}
/**
* Retrieve Configuration Settings - M501
*/
void Config_RetrieveSettings() {
int i = EEPROM_OFFSET;
char stored_ver[4];
char ver[4] = EEPROM_VERSION;
EEPROM_READ_VAR(i, stored_ver); //read stored version
// SERIAL_ECHOLN("Version: [" << ver << "] Stored version: [" << stored_ver << "]");
if (strncmp(ver, stored_ver, 3) != 0) {
Config_ResetDefault();
}
else {
float dummy = 0;
// version number match
EEPROM_READ_VAR(i, axis_steps_per_unit);
EEPROM_READ_VAR(i, max_feedrate);
EEPROM_READ_VAR(i, max_acceleration_units_per_sq_second);
2015-03-15 23:18:11 +01:00
// steps per sq second need to be updated to agree with the units per sq second (as they are what is used in the planner)
reset_acceleration_rates();
EEPROM_READ_VAR(i, acceleration);
EEPROM_READ_VAR(i, retract_acceleration);
EEPROM_READ_VAR(i, travel_acceleration);
EEPROM_READ_VAR(i, minimumfeedrate);
EEPROM_READ_VAR(i, mintravelfeedrate);
EEPROM_READ_VAR(i, minsegmenttime);
EEPROM_READ_VAR(i, max_xy_jerk);
EEPROM_READ_VAR(i, max_z_jerk);
EEPROM_READ_VAR(i, max_e_jerk);
EEPROM_READ_VAR(i, home_offset);
2015-04-27 06:06:04 +02:00
uint8_t dummy_uint8 = 0, mesh_num_x = 0, mesh_num_y = 0;
EEPROM_READ_VAR(i, dummy_uint8);
EEPROM_READ_VAR(i, mesh_num_x);
EEPROM_READ_VAR(i, mesh_num_y);
#if ENABLED(MESH_BED_LEVELING)
2015-04-27 06:06:04 +02:00
mbl.active = dummy_uint8;
if (mesh_num_x == MESH_NUM_X_POINTS && mesh_num_y == MESH_NUM_Y_POINTS) {
EEPROM_READ_VAR(i, mbl.z_values);
2015-04-27 06:06:04 +02:00
} else {
mbl.reset();
for (uint8_t q = 0; q < mesh_num_x * mesh_num_y; q++) EEPROM_READ_VAR(i, dummy);
}
#else
for (uint8_t q = 0; q < mesh_num_x * mesh_num_y; q++) EEPROM_READ_VAR(i, dummy);
2015-04-27 06:06:04 +02:00
#endif // MESH_BED_LEVELING
2015-03-15 23:18:11 +01:00
#if DISABLED(AUTO_BED_LEVELING_FEATURE)
float zprobe_zoffset = 0;
#endif
EEPROM_READ_VAR(i, zprobe_zoffset);
#if ENABLED(DELTA)
EEPROM_READ_VAR(i, endstop_adj); // 3 floats
EEPROM_READ_VAR(i, delta_radius); // 1 float
EEPROM_READ_VAR(i, delta_diagonal_rod); // 1 float
EEPROM_READ_VAR(i, delta_segments_per_second); // 1 float
#elif ENABLED(Z_DUAL_ENDSTOPS)
EEPROM_READ_VAR(i, z_endstop_adj);
dummy = 0.0f;
for (uint8_t q=5; q--;) EEPROM_READ_VAR(i, dummy);
#else
dummy = 0.0f;
for (uint8_t q=6; q--;) EEPROM_READ_VAR(i, dummy);
#endif
#if DISABLED(ULTIPANEL)
int plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed,
absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed;
#endif
EEPROM_READ_VAR(i, plaPreheatHotendTemp);
EEPROM_READ_VAR(i, plaPreheatHPBTemp);
EEPROM_READ_VAR(i, plaPreheatFanSpeed);
EEPROM_READ_VAR(i, absPreheatHotendTemp);
EEPROM_READ_VAR(i, absPreheatHPBTemp);
EEPROM_READ_VAR(i, absPreheatFanSpeed);
#if ENABLED(PIDTEMP)
for (uint8_t e = 0; e < 4; e++) { // 4 = max extruders currently supported by Marlin
2015-04-04 01:38:05 +02:00
EEPROM_READ_VAR(i, dummy); // Kp
if (e < EXTRUDERS && dummy != DUMMY_PID_VALUE) {
// do not need to scale PID values as the values in EEPROM are already scaled
PID_PARAM(Kp, e) = dummy;
EEPROM_READ_VAR(i, PID_PARAM(Ki, e));
EEPROM_READ_VAR(i, PID_PARAM(Kd, e));
#if ENABLED(PID_ADD_EXTRUSION_RATE)
EEPROM_READ_VAR(i, PID_PARAM(Kc, e));
#else
EEPROM_READ_VAR(i, dummy);
#endif
}
else {
for (uint8_t q=3; q--;) EEPROM_READ_VAR(i, dummy); // Ki, Kd, Kc
}
}
#else // !PIDTEMP
// 4 x 4 = 16 slots for PID parameters
for (uint8_t q=16; q--;) EEPROM_READ_VAR(i, dummy); // 4x Kp, Ki, Kd, Kc
#endif // !PIDTEMP
2015-08-31 04:04:30 +02:00
#if DISABLED(PID_ADD_EXTRUSION_RATE)
int lpq_len;
#endif
EEPROM_READ_VAR(i, lpq_len);
#if DISABLED(PIDTEMPBED)
2015-04-04 01:38:05 +02:00
float bedKp, bedKi, bedKd;
#endif
EEPROM_READ_VAR(i, dummy); // bedKp
if (dummy != DUMMY_PID_VALUE) {
bedKp = dummy; UNUSED(bedKp);
2015-04-04 01:38:05 +02:00
EEPROM_READ_VAR(i, bedKi);
EEPROM_READ_VAR(i, bedKd);
}
else {
for (uint8_t q=2; q--;) EEPROM_READ_VAR(i, dummy); // bedKi, bedKd
2015-04-04 01:38:05 +02:00
}
#if DISABLED(HAS_LCD_CONTRAST)
int lcd_contrast;
#endif
EEPROM_READ_VAR(i, lcd_contrast);
#if ENABLED(SCARA)
EEPROM_READ_VAR(i, axis_scaling); // 3 floats
#else
EEPROM_READ_VAR(i, dummy);
#endif
#if ENABLED(FWRETRACT)
EEPROM_READ_VAR(i, autoretract_enabled);
EEPROM_READ_VAR(i, retract_length);
#if EXTRUDERS > 1
EEPROM_READ_VAR(i, retract_length_swap);
#else
EEPROM_READ_VAR(i, dummy);
#endif
EEPROM_READ_VAR(i, retract_feedrate);
EEPROM_READ_VAR(i, retract_zlift);
EEPROM_READ_VAR(i, retract_recover_length);
#if EXTRUDERS > 1
EEPROM_READ_VAR(i, retract_recover_length_swap);
#else
EEPROM_READ_VAR(i, dummy);
#endif
EEPROM_READ_VAR(i, retract_recover_feedrate);
#endif // FWRETRACT
EEPROM_READ_VAR(i, volumetric_enabled);
for (uint8_t q = 0; q < 4; q++) {
EEPROM_READ_VAR(i, dummy);
if (q < EXTRUDERS) filament_size[q] = dummy;
}
calculate_volumetric_multipliers();
// Call updatePID (similar to when we have processed M301)
updatePID();
// Report settings retrieved and length
SERIAL_ECHO_START;
SERIAL_ECHO(ver);
SERIAL_ECHOPAIR(" stored settings retrieved (", (unsigned long)i);
SERIAL_ECHOLNPGM(" bytes)");
}
#if ENABLED(EEPROM_CHITCHAT)
Config_PrintSettings();
#endif
}
#endif // EEPROM_SETTINGS
/**
* Reset Configuration Settings - M502
*/
void Config_ResetDefault() {
float tmp1[] = DEFAULT_AXIS_STEPS_PER_UNIT;
float tmp2[] = DEFAULT_MAX_FEEDRATE;
long tmp3[] = DEFAULT_MAX_ACCELERATION;
2015-08-11 18:38:26 +02:00
for (uint8_t i = 0; i < NUM_AXIS; i++) {
axis_steps_per_unit[i] = tmp1[i];
max_feedrate[i] = tmp2[i];
max_acceleration_units_per_sq_second[i] = tmp3[i];
#if ENABLED(SCARA)
2015-07-23 00:50:20 +02:00
if (i < COUNT(axis_scaling))
axis_scaling[i] = 1;
#endif
}
// steps per sq second need to be updated to agree with the units per sq second
reset_acceleration_rates();
acceleration = DEFAULT_ACCELERATION;
retract_acceleration = DEFAULT_RETRACT_ACCELERATION;
travel_acceleration = DEFAULT_TRAVEL_ACCELERATION;
minimumfeedrate = DEFAULT_MINIMUMFEEDRATE;
minsegmenttime = DEFAULT_MINSEGMENTTIME;
mintravelfeedrate = DEFAULT_MINTRAVELFEEDRATE;
max_xy_jerk = DEFAULT_XYJERK;
max_z_jerk = DEFAULT_ZJERK;
max_e_jerk = DEFAULT_EJERK;
home_offset[X_AXIS] = home_offset[Y_AXIS] = home_offset[Z_AXIS] = 0;
#if ENABLED(MESH_BED_LEVELING)
2015-03-15 23:18:11 +01:00
mbl.active = 0;
2015-03-26 07:06:33 +01:00
#endif
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
zprobe_zoffset = Z_PROBE_OFFSET_FROM_EXTRUDER;
2015-03-26 07:06:33 +01:00
#endif
2015-03-15 23:18:11 +01:00
#if ENABLED(DELTA)
endstop_adj[X_AXIS] = endstop_adj[Y_AXIS] = endstop_adj[Z_AXIS] = 0;
delta_radius = DELTA_RADIUS;
delta_diagonal_rod = DELTA_DIAGONAL_ROD;
delta_segments_per_second = DELTA_SEGMENTS_PER_SECOND;
recalc_delta_settings(delta_radius, delta_diagonal_rod);
#elif ENABLED(Z_DUAL_ENDSTOPS)
z_endstop_adj = 0;
#endif
#if ENABLED(ULTIPANEL)
plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP;
plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP;
plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED;
absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP;
absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP;
absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
#endif
#if ENABLED(HAS_LCD_CONTRAST)
lcd_contrast = DEFAULT_LCD_CONTRAST;
#endif
#if ENABLED(PIDTEMP)
#if ENABLED(PID_PARAMS_PER_EXTRUDER)
for (uint8_t e = 0; e < EXTRUDERS; e++)
#else
int e = 0; UNUSED(e); // only need to write once
#endif
{
PID_PARAM(Kp, e) = DEFAULT_Kp;
PID_PARAM(Ki, e) = scalePID_i(DEFAULT_Ki);
PID_PARAM(Kd, e) = scalePID_d(DEFAULT_Kd);
#if ENABLED(PID_ADD_EXTRUSION_RATE)
PID_PARAM(Kc, e) = DEFAULT_Kc;
#endif
}
2015-08-31 04:04:30 +02:00
#if ENABLED(PID_ADD_EXTRUSION_RATE)
lpq_len = 20; // default last-position-queue size
#endif
// call updatePID (similar to when we have processed M301)
updatePID();
#endif // PIDTEMP
#if ENABLED(PIDTEMPBED)
2015-04-04 01:38:05 +02:00
bedKp = DEFAULT_bedKp;
bedKi = scalePID_i(DEFAULT_bedKi);
bedKd = scalePID_d(DEFAULT_bedKd);
#endif
#if ENABLED(FWRETRACT)
autoretract_enabled = false;
retract_length = RETRACT_LENGTH;
#if EXTRUDERS > 1
retract_length_swap = RETRACT_LENGTH_SWAP;
#endif
retract_feedrate = RETRACT_FEEDRATE;
retract_zlift = RETRACT_ZLIFT;
retract_recover_length = RETRACT_RECOVER_LENGTH;
#if EXTRUDERS > 1
retract_recover_length_swap = RETRACT_RECOVER_LENGTH_SWAP;
#endif
retract_recover_feedrate = RETRACT_RECOVER_FEEDRATE;
#endif
volumetric_enabled = false;
for (uint8_t q = 0; q < COUNT(filament_size); q++)
2015-07-24 03:08:06 +02:00
filament_size[q] = DEFAULT_NOMINAL_FILAMENT_DIA;
calculate_volumetric_multipliers();
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("Hardcoded Default Settings Loaded");
}
#if DISABLED(DISABLE_M503)
/**
* Print Configuration Settings - M503
*/
#define CONFIG_ECHO_START do{ if (!forReplay) SERIAL_ECHO_START; }while(0)
void Config_PrintSettings(bool forReplay) {
// Always have this function, even with EEPROM_SETTINGS disabled, the current values will be shown
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Steps per unit:");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M92 X", axis_steps_per_unit[X_AXIS]);
SERIAL_ECHOPAIR(" Y", axis_steps_per_unit[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", axis_steps_per_unit[Z_AXIS]);
SERIAL_ECHOPAIR(" E", axis_steps_per_unit[E_AXIS]);
SERIAL_EOL;
CONFIG_ECHO_START;
#if ENABLED(SCARA)
if (!forReplay) {
SERIAL_ECHOLNPGM("Scaling factors:");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M365 X", axis_scaling[X_AXIS]);
SERIAL_ECHOPAIR(" Y", axis_scaling[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", axis_scaling[Z_AXIS]);
SERIAL_EOL;
CONFIG_ECHO_START;
#endif // SCARA
if (!forReplay) {
SERIAL_ECHOLNPGM("Maximum feedrates (mm/s):");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M203 X", max_feedrate[X_AXIS]);
SERIAL_ECHOPAIR(" Y", max_feedrate[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", max_feedrate[Z_AXIS]);
SERIAL_ECHOPAIR(" E", max_feedrate[E_AXIS]);
SERIAL_EOL;
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Maximum Acceleration (mm/s2):");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M201 X", max_acceleration_units_per_sq_second[X_AXIS]);
SERIAL_ECHOPAIR(" Y", max_acceleration_units_per_sq_second[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", max_acceleration_units_per_sq_second[Z_AXIS]);
SERIAL_ECHOPAIR(" E", max_acceleration_units_per_sq_second[E_AXIS]);
SERIAL_EOL;
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Accelerations: P=printing, R=retract and T=travel");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M204 P", acceleration);
SERIAL_ECHOPAIR(" R", retract_acceleration);
SERIAL_ECHOPAIR(" T", travel_acceleration);
SERIAL_EOL;
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M205 S", minimumfeedrate);
SERIAL_ECHOPAIR(" T", mintravelfeedrate);
SERIAL_ECHOPAIR(" B", minsegmenttime);
SERIAL_ECHOPAIR(" X", max_xy_jerk);
SERIAL_ECHOPAIR(" Z", max_z_jerk);
SERIAL_ECHOPAIR(" E", max_e_jerk);
SERIAL_EOL;
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Home offset (mm):");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M206 X", home_offset[X_AXIS]);
SERIAL_ECHOPAIR(" Y", home_offset[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", home_offset[Z_AXIS]);
SERIAL_EOL;
#if ENABLED(MESH_BED_LEVELING)
if (!forReplay) {
SERIAL_ECHOLNPGM("Mesh bed leveling:");
CONFIG_ECHO_START;
}
2015-04-30 03:26:16 +02:00
SERIAL_ECHOPAIR(" M420 S", (unsigned long)mbl.active);
SERIAL_ECHOPAIR(" X", (unsigned long)MESH_NUM_X_POINTS);
SERIAL_ECHOPAIR(" Y", (unsigned long)MESH_NUM_Y_POINTS);
SERIAL_EOL;
for (uint8_t y = 0; y < MESH_NUM_Y_POINTS; y++) {
for (uint8_t x = 0; x < MESH_NUM_X_POINTS; x++) {
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M421 X", mbl.get_x(x));
SERIAL_ECHOPAIR(" Y", mbl.get_y(y));
SERIAL_ECHOPAIR(" Z", mbl.z_values[y][x]);
SERIAL_EOL;
}
}
#endif
#if ENABLED(DELTA)
CONFIG_ECHO_START;
if (!forReplay) {
2015-04-09 11:04:06 +02:00
SERIAL_ECHOLNPGM("Endstop adjustment (mm):");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M666 X", endstop_adj[X_AXIS]);
SERIAL_ECHOPAIR(" Y", endstop_adj[Y_AXIS]);
SERIAL_ECHOPAIR(" Z", endstop_adj[Z_AXIS]);
SERIAL_EOL;
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Delta settings: L=delta_diagonal_rod, R=delta_radius, S=delta_segments_per_second");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M665 L", delta_diagonal_rod);
SERIAL_ECHOPAIR(" R", delta_radius);
SERIAL_ECHOPAIR(" S", delta_segments_per_second);
SERIAL_EOL;
#elif ENABLED(Z_DUAL_ENDSTOPS)
CONFIG_ECHO_START;
if (!forReplay) {
2015-04-09 11:04:06 +02:00
SERIAL_ECHOLNPGM("Z2 Endstop adjustment (mm):");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M666 Z", z_endstop_adj);
SERIAL_EOL;
#endif // DELTA
#if ENABLED(ULTIPANEL)
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Material heatup parameters:");
CONFIG_ECHO_START;
}
2016-02-28 07:28:08 +01:00
SERIAL_ECHOPAIR(" M145 S0 H", (unsigned long)plaPreheatHotendTemp);
SERIAL_ECHOPAIR(" B", (unsigned long)plaPreheatHPBTemp);
SERIAL_ECHOPAIR(" F", (unsigned long)plaPreheatFanSpeed);
SERIAL_EOL;
CONFIG_ECHO_START;
2016-02-28 07:28:08 +01:00
SERIAL_ECHOPAIR(" M145 S1 H", (unsigned long)absPreheatHotendTemp);
SERIAL_ECHOPAIR(" B", (unsigned long)absPreheatHPBTemp);
SERIAL_ECHOPAIR(" F", (unsigned long)absPreheatFanSpeed);
SERIAL_EOL;
#endif // ULTIPANEL
#if ENABLED(PIDTEMP) || ENABLED(PIDTEMPBED)
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("PID settings:");
}
#if ENABLED(PIDTEMP)
#if EXTRUDERS > 1
if (forReplay) {
for (uint8_t i = 0; i < EXTRUDERS; i++) {
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M301 E", (unsigned long)i);
SERIAL_ECHOPAIR(" P", PID_PARAM(Kp, i));
SERIAL_ECHOPAIR(" I", unscalePID_i(PID_PARAM(Ki, i)));
SERIAL_ECHOPAIR(" D", unscalePID_d(PID_PARAM(Kd, i)));
#if ENABLED(PID_ADD_EXTRUSION_RATE)
SERIAL_ECHOPAIR(" C", PID_PARAM(Kc, i));
2015-08-31 04:04:30 +02:00
if (i == 0) SERIAL_ECHOPAIR(" L", lpq_len);
#endif
SERIAL_EOL;
}
}
else
#endif // EXTRUDERS > 1
// !forReplay || EXTRUDERS == 1
{
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M301 P", PID_PARAM(Kp, 0)); // for compatibility with hosts, only echo values for E0
SERIAL_ECHOPAIR(" I", unscalePID_i(PID_PARAM(Ki, 0)));
SERIAL_ECHOPAIR(" D", unscalePID_d(PID_PARAM(Kd, 0)));
#if ENABLED(PID_ADD_EXTRUSION_RATE)
SERIAL_ECHOPAIR(" C", PID_PARAM(Kc, 0));
2015-08-31 04:04:30 +02:00
SERIAL_ECHOPAIR(" L", lpq_len);
#endif
SERIAL_EOL;
}
#endif // PIDTEMP
#if ENABLED(PIDTEMPBED)
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M304 P", bedKp);
2015-04-04 01:38:05 +02:00
SERIAL_ECHOPAIR(" I", unscalePID_i(bedKi));
SERIAL_ECHOPAIR(" D", unscalePID_d(bedKd));
SERIAL_EOL;
#endif
#endif // PIDTEMP || PIDTEMPBED
#if ENABLED(HAS_LCD_CONTRAST)
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("LCD Contrast:");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M250 C", (unsigned long)lcd_contrast);
SERIAL_EOL;
2015-04-04 01:38:05 +02:00
#endif
#if ENABLED(FWRETRACT)
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Retract: S=Length (mm) F:Speed (mm/m) Z: ZLift (mm)");
CONFIG_ECHO_START;
}
2015-04-04 01:41:58 +02:00
SERIAL_ECHOPAIR(" M207 S", retract_length);
#if EXTRUDERS > 1
SERIAL_ECHOPAIR(" W", retract_length_swap);
#endif
SERIAL_ECHOPAIR(" F", retract_feedrate * 60);
SERIAL_ECHOPAIR(" Z", retract_zlift);
SERIAL_EOL;
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Recover: S=Extra length (mm) F:Speed (mm/m)");
CONFIG_ECHO_START;
}
2015-04-04 01:41:58 +02:00
SERIAL_ECHOPAIR(" M208 S", retract_recover_length);
#if EXTRUDERS > 1
SERIAL_ECHOPAIR(" W", retract_recover_length_swap);
#endif
SERIAL_ECHOPAIR(" F", retract_recover_feedrate * 60);
SERIAL_EOL;
CONFIG_ECHO_START;
if (!forReplay) {
SERIAL_ECHOLNPGM("Auto-Retract: S=0 to disable, 1 to interpret extrude-only moves as retracts or recoveries");
CONFIG_ECHO_START;
}
2015-04-04 01:41:58 +02:00
SERIAL_ECHOPAIR(" M209 S", (unsigned long)(autoretract_enabled ? 1 : 0));
SERIAL_EOL;
#endif // FWRETRACT
/**
* Volumetric extrusion M200
*/
if (!forReplay) {
CONFIG_ECHO_START;
SERIAL_ECHOPGM("Filament settings:");
if (volumetric_enabled)
SERIAL_EOL;
else
SERIAL_ECHOLNPGM(" Disabled");
}
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 D", filament_size[0]);
SERIAL_EOL;
#if EXTRUDERS > 1
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T1 D", filament_size[1]);
SERIAL_EOL;
#if EXTRUDERS > 2
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T2 D", filament_size[2]);
SERIAL_EOL;
#if EXTRUDERS > 3
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M200 T3 D", filament_size[3]);
SERIAL_EOL;
#endif
#endif
#endif
if (!volumetric_enabled) {
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM(" M200 D0");
}
/**
* Auto Bed Leveling
*/
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
#if ENABLED(CUSTOM_M_CODES)
if (!forReplay) {
CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Z-Probe Offset (mm):");
}
CONFIG_ECHO_START;
2015-06-07 23:36:23 +02:00
SERIAL_ECHOPAIR(" M" STRINGIFY(CUSTOM_M_CODE_SET_Z_PROBE_OFFSET) " Z", zprobe_zoffset);
#else
if (!forReplay) {
CONFIG_ECHO_START;
SERIAL_ECHOPAIR("Z-Probe Offset (mm):", zprobe_zoffset);
}
#endif
SERIAL_EOL;
#endif
}
#endif // !DISABLE_M503