2016-07-26 21:32:16 +02:00
/**
* Marlin 3 D Printer Firmware
* Copyright ( C ) 2016 MarlinFirmware [ https : //github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl .
* Copyright ( C ) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software : you can redistribute it and / or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation , either version 3 of the License , or
* ( at your option ) any later version .
*
* This program is distributed in the hope that it will be useful ,
* but WITHOUT ANY WARRANTY ; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE . See the
* GNU General Public License for more details .
*
* You should have received a copy of the GNU General Public License
* along with this program . If not , see < http : //www.gnu.org/licenses/>.
*
*/
/**
* SanityCheck . h
2016-07-29 02:08:28 +02:00
*
* Test configuration values for errors at compile - time .
*/
/**
* Due to the high number of issues related with old versions of Arduino IDE
* we now prevent Marlin from compiling with older toolkits .
*/
# if !defined(ARDUINO) || ARDUINO < 10600
# error "Versions of Arduino IDE prior to 1.6.0 are no longer supported, please update your toolkit."
# endif
/**
* We try our best to include sanity checks for all the changes configuration
* directives because people have a tendency to use outdated config files with
* the bleding edge source code , but sometimes this is not enough . This check
* will force a minimum config file revision , otherwise Marlin will not build .
*/
# if ! defined(CONFIGURATION_H_VERSION) || CONFIGURATION_H_VERSION < REQUIRED_CONFIGURATION_H_VERSION
# error "You are using an old Configuration.h file, update it before building Marlin."
# endif
# if ! defined(CONFIGURATION_ADV_H_VERSION) || CONFIGURATION_ADV_H_VERSION < REQUIRED_CONFIGURATION_ADV_H_VERSION
# error "You are using an old Configuration_adv.h file, update it before building Marlin."
# endif
2016-08-05 06:03:55 +02:00
/**
* Warnings for old configurations
*/
# if WATCH_TEMP_PERIOD > 500
# error "WATCH_TEMP_PERIOD now uses seconds instead of milliseconds."
# elif DISABLED(THERMAL_PROTECTION_HOTENDS) && (defined(WATCH_TEMP_PERIOD) || defined(THERMAL_PROTECTION_PERIOD))
# error "Thermal Runaway Protection for hotends is now enabled with THERMAL_PROTECTION_HOTENDS."
# elif DISABLED(THERMAL_PROTECTION_BED) && defined(THERMAL_PROTECTION_BED_PERIOD)
# error "Thermal Runaway Protection for the bed is now enabled with THERMAL_PROTECTION_BED."
# elif ENABLED(COREXZ) && ENABLED(Z_LATE_ENABLE)
# error "Z_LATE_ENABLE can't be used with COREXZ."
# elif defined(X_HOME_RETRACT_MM)
# error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM."
# elif defined(BEEPER)
# error "BEEPER is now BEEPER_PIN. Please update your pins definitions."
# elif defined(SDCARDDETECT)
# error "SDCARDDETECT is now SD_DETECT_PIN. Please update your pins definitions."
# elif defined(SDCARDDETECTINVERTED)
# error "SDCARDDETECTINVERTED is now SD_DETECT_INVERTED. Please update your configuration."
# elif defined(BTENABLED)
# error "BTENABLED is now BLUETOOTH. Please update your configuration."
# elif defined(CUSTOM_MENDEL_NAME)
# error "CUSTOM_MENDEL_NAME is now CUSTOM_MACHINE_NAME. Please update your configuration."
# elif defined(HAS_AUTOMATIC_VERSIONING)
# error "HAS_AUTOMATIC_VERSIONING is now USE_AUTOMATIC_VERSIONING. Please update your configuration."
# elif defined(ENABLE_AUTO_BED_LEVELING)
# error "ENABLE_AUTO_BED_LEVELING is now AUTO_BED_LEVELING_FEATURE. Please update your configuration."
# elif defined(SDSLOW)
# error "SDSLOW deprecated. Set SPI_SPEED to SPI_HALF_SPEED instead."
# elif defined(SDEXTRASLOW)
# error "SDEXTRASLOW deprecated. Set SPI_SPEED to SPI_QUARTER_SPEED instead."
# elif defined(FILAMENT_SENSOR)
# error "FILAMENT_SENSOR is deprecated. Use FILAMENT_WIDTH_SENSOR instead."
# elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS)
# error "DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated. Use individual USE_*_PLUG options instead."
# elif ENABLED(Z_DUAL_ENDSTOPS) && !defined(Z2_USE_ENDSTOP)
# error "Z_DUAL_ENDSTOPS settings are simplified. Just set Z2_USE_ENDSTOP to the endstop you want to repurpose for Z2"
# elif defined(LANGUAGE_INCLUDE)
# error "LANGUAGE_INCLUDE has been replaced by LCD_LANGUAGE. Please update your configuration."
# elif defined(EXTRUDER_OFFSET_X) || defined(EXTRUDER_OFFSET_Y)
# error "EXTRUDER_OFFSET_[XY] is deprecated. Use HOTEND_OFFSET_[XY] instead."
# elif defined(PID_PARAMS_PER_EXTRUDER)
# error "PID_PARAMS_PER_EXTRUDER is deprecated. Use PID_PARAMS_PER_HOTEND instead."
# elif defined(EXTRUDER_WATTS) || defined(BED_WATTS)
# error "EXTRUDER_WATTS and BED_WATTS are deprecated. Remove them from your configuration."
# elif defined(SERVO_ENDSTOP_ANGLES)
# error "SERVO_ENDSTOP_ANGLES is deprecated. Use Z_SERVO_ANGLES instead."
# elif defined(X_ENDSTOP_SERVO_NR) || defined(Y_ENDSTOP_SERVO_NR)
# error "X_ENDSTOP_SERVO_NR and Y_ENDSTOP_SERVO_NR are deprecated and should be removed."
# elif defined(XY_TRAVEL_SPEED)
# error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead."
# elif defined(PROBE_SERVO_DEACTIVATION_DELAY)
# error "PROBE_SERVO_DEACTIVATION_DELAY is deprecated. Use DEACTIVATE_SERVOS_AFTER_MOVE instead."
# elif defined(SERVO_DEACTIVATION_DELAY)
# error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead."
# elif ENABLED(FILAMENTCHANGEENABLE)
# error "FILAMENTCHANGEENABLE is now FILAMENT_CHANGE_FEATURE. Please update your configuration."
# elif defined(PLA_PREHEAT_HOTEND_TEMP)
# error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND. Please update your configuration."
# elif defined(PLA_PREHEAT_HPB_TEMP)
# error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED. Please update your configuration."
# elif defined(PLA_PREHEAT_FAN_SPEED)
# error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED. Please update your configuration."
# elif defined(ABS_PREHEAT_HOTEND_TEMP)
# error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND. Please update your configuration."
# elif defined(ABS_PREHEAT_HPB_TEMP)
# error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED. Please update your configuration."
# elif defined(ABS_PREHEAT_FAN_SPEED)
# error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED. Please update your configuration."
# elif defined(ENDSTOPS_ONLY_FOR_HOMING)
# error "ENDSTOPS_ONLY_FOR_HOMING is deprecated. Use (disable) ENDSTOPS_ALWAYS_ON_DEFAULT instead."
# elif defined(HOMING_FEEDRATE)
# error "HOMING_FEEDRATE is deprecated. Set individual rates with HOMING_FEEDRATE_(XY|Z|E) instead."
# elif defined(MANUAL_HOME_POSITIONS)
# error "MANUAL_HOME_POSITIONS is deprecated. Set MANUAL_[XYZ]_HOME_POS as-needed instead."
# elif defined(PID_ADD_EXTRUSION_RATE)
# error "PID_ADD_EXTRUSION_RATE is now PID_EXTRUSION_SCALING and is DISABLED by default. Are you sure you want to use this option? Please update your configuration."
# elif defined(Z_RAISE_BEFORE_HOMING)
# error "Z_RAISE_BEFORE_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
# elif defined(MIN_Z_HEIGHT_FOR_HOMING)
# error "MIN_Z_HEIGHT_FOR_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
# elif defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING)
2016-09-20 10:49:42 +02:00
# error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_CLEARANCE_DEPLOY_PROBE instead."
2016-08-05 06:03:55 +02:00
# elif defined(Z_RAISE_PROBE_DEPLOY_STOW) || defined(Z_RAISE_BETWEEN_PROBINGS)
2016-09-20 10:49:42 +02:00
# error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
2016-09-14 03:25:12 +02:00
# elif defined(Z_PROBE_DEPLOY_HEIGHT) || defined(Z_PROBE_TRAVEL_HEIGHT)
2016-09-20 10:49:42 +02:00
# error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
2016-08-21 15:56:03 +02:00
# elif !defined(MIN_STEPS_PER_SEGMENT)
2016-08-29 02:40:32 +02:00
# error Please replace "const int dropsegments" with "#define MIN_STEPS_PER_SEGMENT" (and increase by 1) in Configuration_adv.h.
2016-08-21 06:34:24 +02:00
# elif defined(PREVENT_DANGEROUS_EXTRUDE)
# error "PREVENT_DANGEROUS_EXTRUDE is now PREVENT_COLD_EXTRUSION. Please update your configuration."
2016-09-12 03:11:39 +02:00
# elif defined(SCARA)
# error "SCARA is now MORGAN_SCARA. Please update your configuration."
2016-09-15 20:56:56 +02:00
# elif defined(AUTO_BED_LEVELING_GRID_POINTS)
# error "AUTO_BED_LEVELING_GRID_POINTS is now ABL_GRID_POINTS_X and ABL_GRID_POINTS_Y. Please update your configuration."
2016-08-05 06:03:55 +02:00
# endif
2016-07-29 02:08:28 +02:00
/**
* Marlin release , version and default string
*/
# ifndef SHORT_BUILD_VERSION
# error "SHORT_BUILD_VERSION must be specified."
# elif !defined(DETAILED_BUILD_VERSION)
# error "BUILD_VERSION must be specified."
# elif !defined(STRING_DISTRIBUTION_DATE)
# error "STRING_DISTRIBUTION_DATE must be specified."
# elif !defined(PROTOCOL_VERSION)
# error "PROTOCOL_VERSION must be specified."
# elif !defined(MACHINE_NAME)
# error "MACHINE_NAME must be specified."
# elif !defined(SOURCE_CODE_URL)
# error "SOURCE_CODE_URL must be specified."
# elif !defined(DEFAULT_MACHINE_UUID)
# error "DEFAULT_MACHINE_UUID must be specified."
# elif !defined(WEBSITE_URL)
# error "WEBSITE_URL must be specified."
# endif
/**
* Dual Stepper Drivers
*/
# if ENABLED(X_DUAL_STEPPER_DRIVERS) && ENABLED(DUAL_X_CARRIAGE)
# error "DUAL_X_CARRIAGE is not compatible with X_DUAL_STEPPER_DRIVERS."
# elif ENABLED(X_DUAL_STEPPER_DRIVERS) && (!HAS_X2_ENABLE || !HAS_X2_STEP || !HAS_X2_DIR)
# error "X_DUAL_STEPPER_DRIVERS requires X2 pins (and an extra E plug)."
# elif ENABLED(Y_DUAL_STEPPER_DRIVERS) && (!HAS_Y2_ENABLE || !HAS_Y2_STEP || !HAS_Y2_DIR)
# error "Y_DUAL_STEPPER_DRIVERS requires Y2 pins (and an extra E plug)."
# elif ENABLED(Z_DUAL_STEPPER_DRIVERS) && (!HAS_Z2_ENABLE || !HAS_Z2_STEP || !HAS_Z2_DIR)
# error "Z_DUAL_STEPPER_DRIVERS requires Z2 pins (and an extra E plug)."
# endif
/**
* Progress Bar
*/
# if ENABLED(LCD_PROGRESS_BAR)
# if DISABLED(SDSUPPORT)
# error "LCD_PROGRESS_BAR requires SDSUPPORT."
2016-09-12 05:42:54 +02:00
# elif ENABLED(DOGLCD)
2016-07-29 02:08:28 +02:00
# error "LCD_PROGRESS_BAR does not apply to graphical displays."
2016-09-12 05:42:54 +02:00
# elif ENABLED(FILAMENT_LCD_DISPLAY)
2016-07-29 02:08:28 +02:00
# error "LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both."
# endif
# endif
2016-08-05 17:17:06 +02:00
/**
* Delta requirements
*/
# if ENABLED(DELTA)
# if DISABLED(USE_XMAX_PLUG) && DISABLED(USE_YMAX_PLUG) && DISABLED(USE_ZMAX_PLUG)
# error "You probably want to use Max Endstops for DELTA!"
# endif
2016-08-19 11:31:03 +02:00
# if ENABLED(AUTO_BED_LEVELING_GRID)
2016-09-15 20:56:56 +02:00
# if (ABL_GRID_POINTS_X & 1) == 0 || (ABL_GRID_POINTS_Y & 1) == 0
# error "DELTA requires ABL_GRID_POINTS_X and ABL_GRID_POINTS_Y to be odd numbers."
# elif ABL_GRID_POINTS_X < 3
# error "DELTA requires ABL_GRID_POINTS_X and ABL_GRID_POINTS_Y to be 3 or higher."
2016-08-19 11:31:03 +02:00
# endif
# endif
2016-08-05 17:17:06 +02:00
# endif
2016-07-29 02:08:28 +02:00
/**
* Babystepping
*/
# if ENABLED(BABYSTEPPING)
# if DISABLED(ULTRA_LCD)
# error "BABYSTEPPING requires an LCD controller."
# endif
# if ENABLED(SCARA)
# error "BABYSTEPPING is not implemented for SCARA yet."
# endif
# if ENABLED(DELTA) && ENABLED(BABYSTEP_XY)
# error "BABYSTEPPING only implemented for Z axis on deltabots."
# endif
# endif
/**
* Filament Runout needs a pin and either SD Support or Auto print start detection
*/
# if ENABLED(FILAMENT_RUNOUT_SENSOR)
# if !HAS_FIL_RUNOUT
# error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN."
# elif DISABLED(SDSUPPORT) && DISABLED(PRINTJOB_TIMER_AUTOSTART)
# error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART."
# endif
# endif
/**
* Filament Change with Extruder Runout Prevention
*/
# if ENABLED(FILAMENT_CHANGE_FEATURE) && ENABLED(EXTRUDER_RUNOUT_PREVENT)
# error "EXTRUDER_RUNOUT_PREVENT is incompatible with FILAMENT_CHANGE_FEATURE."
# endif
/**
* Individual axis homing is useless for DELTAS
*/
# if ENABLED(INDIVIDUAL_AXIS_HOMING_MENU) && ENABLED(DELTA)
# error "INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics."
# endif
/**
* Options only for EXTRUDERS > 1
*/
# if EXTRUDERS > 1
# if EXTRUDERS > 4
# error "The maximum number of EXTRUDERS in Marlin is 4."
# endif
# if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
# error "EXTRUDERS must be 1 with TEMP_SENSOR_1_AS_REDUNDANT."
# endif
# if ENABLED(HEATERS_PARALLEL)
# error "EXTRUDERS must be 1 with HEATERS_PARALLEL."
# endif
# elif ENABLED(SINGLENOZZLE)
# error "SINGLENOZZLE requires 2 or more EXTRUDERS."
# endif
/**
* Only one type of extruder allowed
*/
# if (ENABLED(SWITCHING_EXTRUDER) && (ENABLED(SINGLENOZZLE) || ENABLED(MIXING_EXTRUDER))) \
| | ( ENABLED ( SINGLENOZZLE ) & & ENABLED ( MIXING_EXTRUDER ) )
# error "Please define only one type of extruder: SINGLENOZZLE, SWITCHING_EXTRUDER, or MIXING_EXTRUDER."
# endif
/**
* Single Stepper Dual Extruder with switching servo
*/
# if ENABLED(SWITCHING_EXTRUDER)
# if ENABLED(DUAL_X_CARRIAGE)
# error "SWITCHING_EXTRUDER and DUAL_X_CARRIAGE are incompatible."
# elif EXTRUDERS != 2
# error "SWITCHING_EXTRUDER requires exactly 2 EXTRUDERS."
# elif NUM_SERVOS < 1
# error "SWITCHING_EXTRUDER requires NUM_SERVOS >= 1."
# endif
# endif
/**
* Mixing Extruder requirements
*/
# if ENABLED(MIXING_EXTRUDER)
# if EXTRUDERS > 1
# error "MIXING_EXTRUDER currently only supports one extruder."
# endif
# if MIXING_STEPPERS < 2
# error "You must set MIXING_STEPPERS >= 2 for a mixing extruder."
# endif
# if ENABLED(FILAMENT_SENSOR)
# error "MIXING_EXTRUDER is incompatible with FILAMENT_SENSOR. Comment out this line to use it anyway."
# endif
# endif
/**
* Limited number of servos
*/
2016-09-19 04:46:10 +02:00
# if NUM_SERVOS > 4
# error "The maximum number of SERVOS in Marlin is 4."
2016-07-29 02:08:28 +02:00
# endif
/**
* Servo deactivation depends on servo endstops
*/
# if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) && !HAS_Z_SERVO_ENDSTOP
# error "Z_ENDSTOP_SERVO_NR is required for DEACTIVATE_SERVOS_AFTER_MOVE."
# endif
/**
* Required LCD language
*/
# if DISABLED(DOGLCD) && ENABLED(ULTRA_LCD) && !defined(DISPLAY_CHARSET_HD44780)
# error "You must set DISPLAY_CHARSET_HD44780 to JAPANESE, WESTERN or CYRILLIC for your LCD controller."
# endif
/**
* Bed Heating Options - PID vs Limit Switching
*/
# if ENABLED(PIDTEMPBED) && ENABLED(BED_LIMIT_SWITCHING)
# error "To use BED_LIMIT_SWITCHING you must disable PIDTEMPBED."
# endif
/**
* Mesh Bed Leveling
*/
# if ENABLED(MESH_BED_LEVELING)
# if ENABLED(DELTA)
# error "MESH_BED_LEVELING does not yet support DELTA printers."
# elif ENABLED(AUTO_BED_LEVELING_FEATURE)
# error "Select AUTO_BED_LEVELING_FEATURE or MESH_BED_LEVELING, not both."
# elif MESH_NUM_X_POINTS > 9 || MESH_NUM_Y_POINTS > 9
# error "MESH_NUM_X_POINTS and MESH_NUM_Y_POINTS must be less than 10."
# endif
# elif ENABLED(MANUAL_BED_LEVELING)
# error "MESH_BED_LEVELING is required for MANUAL_BED_LEVELING."
# endif
/**
* Probes
*/
# if PROBE_SELECTED
2016-09-19 06:28:11 +02:00
/**
* Only allow one probe option to be defined
*/
# define COUNT_PROBE_1 0
# if ENABLED(FIX_MOUNTED_PROBE)
# define COUNT_PROBE_2 INCREMENT(COUNT_PROBE_1)
# else
# define COUNT_PROBE_2 COUNT_PROBE_1
# endif
# if HAS_Z_SERVO_ENDSTOP && DISABLED(BLTOUCH)
# define COUNT_PROBE_3 INCREMENT(COUNT_PROBE_2)
# else
# define COUNT_PROBE_3 COUNT_PROBE_2
# endif
# if ENABLED(BLTOUCH)
# define COUNT_PROBE_4 INCREMENT(COUNT_PROBE_3)
# else
# define COUNT_PROBE_4 COUNT_PROBE_3
# endif
# if ENABLED(Z_PROBE_ALLEN_KEY)
# define COUNT_PROBE_5 INCREMENT(COUNT_PROBE_4)
# else
# define COUNT_PROBE_5 COUNT_PROBE_4
# endif
# if ENABLED(Z_PROBE_SLED)
# define COUNT_PROBE_6 INCREMENT(COUNT_PROBE_5)
# else
# define COUNT_PROBE_6 COUNT_PROBE_5
# endif
# if COUNT_PROBE_6 > 1
# error "Please enable only one probe: FIX_MOUNTED_PROBE, Z Servo, BLTOUCH, Z_PROBE_ALLEN_KEY, or Z_PROBE_SLED."
# endif
/**
* Z_PROBE_SLED is incompatible with DELTA
*/
2016-07-29 02:08:28 +02:00
# if ENABLED(Z_PROBE_SLED) && ENABLED(DELTA)
# error "You cannot use Z_PROBE_SLED with DELTA."
# endif
/**
* NUM_SERVOS is required for a Z servo probe
*/
# if HAS_Z_SERVO_ENDSTOP
# ifndef NUM_SERVOS
# error "You must set NUM_SERVOS for a Z servo probe (Z_ENDSTOP_SERVO_NR)."
# elif Z_ENDSTOP_SERVO_NR >= NUM_SERVOS
2016-09-19 04:46:10 +02:00
# error "Z_ENDSTOP_SERVO_NR must be smaller than NUM_SERVOS."
2016-07-29 02:08:28 +02:00
# endif
# endif
/**
2016-09-19 06:28:11 +02:00
* Require pin options and pins to be defined
2016-07-29 02:08:28 +02:00
*/
2016-09-19 06:28:11 +02:00
# if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
# if ENABLED(Z_MIN_PROBE_ENDSTOP)
# error "Enable only one option: Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN."
# elif DISABLED(USE_ZMIN_PLUG)
# error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires USE_ZMIN_PLUG to be enabled."
# elif !HAS_Z_MIN
# error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires the Z_MIN_PIN to be defined."
2016-08-03 05:55:17 +02:00
# endif
2016-09-19 06:28:11 +02:00
# elif ENABLED(Z_MIN_PROBE_ENDSTOP)
2016-07-29 02:08:28 +02:00
# if !HAS_Z_MIN_PROBE_PIN
2016-09-19 06:28:11 +02:00
# error "Z_MIN_PROBE_ENDSTOP requires the Z_MIN_PROBE_PIN to be defined."
2016-07-29 02:08:28 +02:00
# endif
2016-09-19 06:28:11 +02:00
# else
# error "You must enable either Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use a probe."
2016-07-29 02:08:28 +02:00
# endif
/**
* Make sure Z raise values are set
*/
2016-09-20 10:49:42 +02:00
# if !defined(Z_CLEARANCE_DEPLOY_PROBE)
# error "You must define Z_CLEARANCE_DEPLOY_PROBE in your configuration."
# elif !defined(Z_CLEARANCE_BETWEEN_PROBES)
# error "You must define Z_CLEARANCE_BETWEEN_PROBES in your configuration."
# elif Z_CLEARANCE_DEPLOY_PROBE < 0
# error "Probes need Z_CLEARANCE_DEPLOY_PROBE >= 0."
# elif Z_CLEARANCE_BETWEEN_PROBES < 0
# error "Probes need Z_CLEARANCE_BETWEEN_PROBES >= 0."
2016-07-29 02:08:28 +02:00
# endif
# else
/**
* Require some kind of probe for bed leveling and probe testing
*/
# if ENABLED(AUTO_BED_LEVELING_FEATURE)
# error "AUTO_BED_LEVELING_FEATURE requires a probe! Define a Z Servo, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or FIX_MOUNTED_PROBE."
# elif ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
# error "Z_MIN_PROBE_REPEATABILITY_TEST requires a probe! Define a Z Servo, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or FIX_MOUNTED_PROBE."
# endif
# endif
/**
* Make sure Z_SAFE_HOMING point is reachable
*/
# if ENABLED(Z_SAFE_HOMING)
# if Z_SAFE_HOMING_X_POINT < MIN_PROBE_X || Z_SAFE_HOMING_X_POINT > MAX_PROBE_X
# if HAS_BED_PROBE
# error "Z_SAFE_HOMING_X_POINT can't be reached by the Z probe."
# else
# error "Z_SAFE_HOMING_X_POINT can't be reached by the nozzle."
# endif
# elif Z_SAFE_HOMING_Y_POINT < MIN_PROBE_Y || Z_SAFE_HOMING_Y_POINT > MAX_PROBE_Y
# if HAS_BED_PROBE
# error "Z_SAFE_HOMING_Y_POINT can't be reached by the Z probe."
# else
# error "Z_SAFE_HOMING_Y_POINT can't be reached by the nozzle."
# endif
# endif
# endif // Z_SAFE_HOMING
/**
* Auto Bed Leveling
*/
# if ENABLED(AUTO_BED_LEVELING_FEATURE)
/**
* Delta has limited bed leveling options
*/
# if ENABLED(DELTA) && DISABLED(AUTO_BED_LEVELING_GRID)
# error "You must use AUTO_BED_LEVELING_GRID for DELTA bed leveling."
# endif
/**
* Check if Probe_Offset * Grid Points is greater than Probing Range
*/
# if ENABLED(AUTO_BED_LEVELING_GRID)
# ifndef DELTA_PROBEABLE_RADIUS
// Be sure points are in the right order
# if LEFT_PROBE_BED_POSITION > RIGHT_PROBE_BED_POSITION
# error "LEFT_PROBE_BED_POSITION must be less than RIGHT_PROBE_BED_POSITION."
# elif FRONT_PROBE_BED_POSITION > BACK_PROBE_BED_POSITION
# error "FRONT_PROBE_BED_POSITION must be less than BACK_PROBE_BED_POSITION."
# endif
// Make sure probing points are reachable
# if LEFT_PROBE_BED_POSITION < MIN_PROBE_X
# error "The given LEFT_PROBE_BED_POSITION can't be reached by the Z probe."
# elif RIGHT_PROBE_BED_POSITION > MAX_PROBE_X
# error "The given RIGHT_PROBE_BED_POSITION can't be reached by the Z probe."
# elif FRONT_PROBE_BED_POSITION < MIN_PROBE_Y
# error "The given FRONT_PROBE_BED_POSITION can't be reached by the Z probe."
# elif BACK_PROBE_BED_POSITION > MAX_PROBE_Y
# error "The given BACK_PROBE_BED_POSITION can't be reached by the Z probe."
# endif
# endif
# else // !AUTO_BED_LEVELING_GRID
// Check the triangulation points
# if ABL_PROBE_PT_1_X < MIN_PROBE_X || ABL_PROBE_PT_1_X > MAX_PROBE_X
# error "The given ABL_PROBE_PT_1_X can't be reached by the Z probe."
# elif ABL_PROBE_PT_2_X < MIN_PROBE_X || ABL_PROBE_PT_2_X > MAX_PROBE_X
# error "The given ABL_PROBE_PT_2_X can't be reached by the Z probe."
# elif ABL_PROBE_PT_3_X < MIN_PROBE_X || ABL_PROBE_PT_3_X > MAX_PROBE_X
# error "The given ABL_PROBE_PT_3_X can't be reached by the Z probe."
# elif ABL_PROBE_PT_1_Y < MIN_PROBE_Y || ABL_PROBE_PT_1_Y > MAX_PROBE_Y
# error "The given ABL_PROBE_PT_1_Y can't be reached by the Z probe."
# elif ABL_PROBE_PT_2_Y < MIN_PROBE_Y || ABL_PROBE_PT_2_Y > MAX_PROBE_Y
# error "The given ABL_PROBE_PT_2_Y can't be reached by the Z probe."
# elif ABL_PROBE_PT_3_Y < MIN_PROBE_Y || ABL_PROBE_PT_3_Y > MAX_PROBE_Y
# error "The given ABL_PROBE_PT_3_Y can't be reached by the Z probe."
# endif
# endif // !AUTO_BED_LEVELING_GRID
# endif // AUTO_BED_LEVELING_FEATURE
/**
* Advance Extrusion
*/
# if ENABLED(ADVANCE) && ENABLED(LIN_ADVANCE)
# error "You can enable ADVANCE or LIN_ADVANCE, but not both."
# endif
/**
* Filament Width Sensor
*/
# if ENABLED(FILAMENT_WIDTH_SENSOR) && !HAS_FILAMENT_WIDTH_SENSOR
# error "FILAMENT_WIDTH_SENSOR requires a FILWIDTH_PIN to be defined."
# endif
/**
* ULTIPANEL encoder
*/
# if ENABLED(ULTIPANEL) && DISABLED(NEWPANEL) && DISABLED(SR_LCD_2W_NL) && !defined(SHIFT_CLK)
# error "ULTIPANEL requires some kind of encoder."
# endif
# if ENCODER_PULSES_PER_STEP < 0
# error "ENCODER_PULSES_PER_STEP should not be negative, use REVERSE_MENU_DIRECTION instead."
# endif
/**
* SAV_3DGLCD display options
*/
# if ENABLED(U8GLIB_SSD1306) && ENABLED(U8GLIB_SH1106)
# error "Only enable one SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106."
# endif
/**
* Don ' t set more than one kinematic type
*/
2016-09-12 06:39:15 +02:00
# define COUNT_KIN_1 0
# if ENABLED(DELTA)
# define COUNT_KIN_2 INCREMENT(COUNT_KIN_1)
# else
# define COUNT_KIN_2 COUNT_KIN_1
# endif
# if ENABLED(MORGAN_SCARA)
# define COUNT_KIN_3 INCREMENT(COUNT_KIN_2)
# else
# define COUNT_KIN_3 COUNT_KIN_2
# endif
# if ENABLED(MAKERARM_SCARA)
# define COUNT_KIN_4 INCREMENT(COUNT_KIN_3)
# else
# define COUNT_KIN_4 COUNT_KIN_3
# endif
# if ENABLED(COREXY)
# define COUNT_KIN_5 INCREMENT(COUNT_KIN_4)
# else
# define COUNT_KIN_5 COUNT_KIN_4
# endif
# if ENABLED(COREXZ)
# define COUNT_KIN_6 INCREMENT(COUNT_KIN_5)
# else
# define COUNT_KIN_6 COUNT_KIN_5
# endif
# if ENABLED(COREYZ)
# define COUNT_KIN_7 INCREMENT(COUNT_KIN_6)
# else
# define COUNT_KIN_7 COUNT_KIN_6
# endif
# if COUNT_KIN_7 > 1
2016-09-12 03:11:39 +02:00
# error "Please enable only one of DELTA, MORGAN_SCARA, MAKERARM_SCARA, COREXY, COREXZ, or COREYZ."
2016-07-29 02:08:28 +02:00
# endif
/**
* Allen Key
* Deploying the Allen Key probe uses big moves in z direction . Too dangerous for an unhomed z - axis .
*/
# if ENABLED(Z_PROBE_ALLEN_KEY) && (Z_HOME_DIR < 0) && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
# error "You can't home to a z min endstop with a Z_PROBE_ALLEN_KEY"
# endif
/**
* Dual X Carriage requirements
*/
# if ENABLED(DUAL_X_CARRIAGE)
# if EXTRUDERS == 1
# error "DUAL_X_CARRIAGE requires 2 (or more) extruders."
# elif ENABLED(COREXY) || ENABLED(COREXZ)
# error "DUAL_X_CARRIAGE cannot be used with COREXY or COREXZ."
# elif !HAS_X2_ENABLE || !HAS_X2_STEP || !HAS_X2_DIR
# error "DUAL_X_CARRIAGE requires X2 stepper pins to be defined."
# elif !HAS_X_MAX
# error "DUAL_X_CARRIAGE requires USE_XMAX_PLUG and an X Max Endstop."
# elif !defined(X2_HOME_POS) || !defined(X2_MIN_POS) || !defined(X2_MAX_POS)
# error "DUAL_X_CARRIAGE requires X2_HOME_POS, X2_MIN_POS, and X2_MAX_POS."
# elif X_HOME_DIR != -1 || X2_HOME_DIR != 1
# error "DUAL_X_CARRIAGE requires X_HOME_DIR -1 and X2_HOME_DIR 1."
# endif
# endif // DUAL_X_CARRIAGE
/**
* Make sure auto fan pins don ' t conflict with the fan pin
*/
# if HAS_AUTO_FAN
# if HAS_FAN0
# if EXTRUDER_0_AUTO_FAN_PIN == FAN_PIN
# error "You cannot set EXTRUDER_0_AUTO_FAN_PIN equal to FAN_PIN."
# elif EXTRUDER_1_AUTO_FAN_PIN == FAN_PIN
# error "You cannot set EXTRUDER_1_AUTO_FAN_PIN equal to FAN_PIN."
# elif EXTRUDER_2_AUTO_FAN_PIN == FAN_PIN
# error "You cannot set EXTRUDER_2_AUTO_FAN_PIN equal to FAN_PIN."
# elif EXTRUDER_3_AUTO_FAN_PIN == FAN_PIN
# error "You cannot set EXTRUDER_3_AUTO_FAN_PIN equal to FAN_PIN."
# endif
# endif
# endif
# if HAS_FAN0 && CONTROLLERFAN_PIN == FAN_PIN
# error "You cannot set CONTROLLERFAN_PIN equal to FAN_PIN."
# endif
# if HAS_CONTROLLERFAN
# if EXTRUDER_0_AUTO_FAN_PIN == CONTROLLERFAN_PIN
# error "You cannot set EXTRUDER_0_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
# elif EXTRUDER_1_AUTO_FAN_PIN == CONTROLLERFAN_PIN
# error "You cannot set EXTRUDER_1_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
# elif EXTRUDER_2_AUTO_FAN_PIN == CONTROLLERFAN_PIN
# error "You cannot set EXTRUDER_2_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
# elif EXTRUDER_3_AUTO_FAN_PIN == CONTROLLERFAN_PIN
# error "You cannot set EXTRUDER_3_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
# endif
# endif
/**
* Test Heater , Temp Sensor , and Extruder Pins ; Sensor Type must also be set .
*/
# if !HAS_HEATER_0
# error "HEATER_0_PIN not defined for this board."
# elif !PIN_EXISTS(TEMP_0)
# error "TEMP_0_PIN not defined for this board."
# elif !PIN_EXISTS(E0_STEP) || !PIN_EXISTS(E0_DIR) || !PIN_EXISTS(E0_ENABLE)
# error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board."
# elif TEMP_SENSOR_0 == 0
# error "TEMP_SENSOR_0 is required."
# endif
# if HOTENDS > 1 || ENABLED(HEATERS_PARALLEL)
# if !HAS_HEATER_1
# error "HEATER_1_PIN not defined for this board."
# endif
# endif
# if HOTENDS > 1
# if TEMP_SENSOR_1 == 0
# error "TEMP_SENSOR_1 is required with 2 or more HOTENDS."
# elif !PIN_EXISTS(TEMP_1)
# error "TEMP_1_PIN not defined for this board."
# endif
# if HOTENDS > 2
# if TEMP_SENSOR_2 == 0
# error "TEMP_SENSOR_2 is required with 3 or more HOTENDS."
# elif !HAS_HEATER_2
# error "HEATER_2_PIN not defined for this board."
# elif !PIN_EXISTS(TEMP_2)
# error "TEMP_2_PIN not defined for this board."
# endif
# if HOTENDS > 3
# if TEMP_SENSOR_3 == 0
# error "TEMP_SENSOR_3 is required with 4 HOTENDS."
# elif !HAS_HEATER_3
# error "HEATER_3_PIN not defined for this board."
# elif !PIN_EXISTS(TEMP_3)
# error "TEMP_3_PIN not defined for this board."
# endif
# elif TEMP_SENSOR_3 != 0
# error "TEMP_SENSOR_3 shouldn't be set with only 3 extruders."
# endif
# elif TEMP_SENSOR_2 != 0
# error "TEMP_SENSOR_2 shouldn't be set with only 2 extruders."
# elif TEMP_SENSOR_3 != 0
# error "TEMP_SENSOR_3 shouldn't be set with only 2 extruders."
# endif
# elif TEMP_SENSOR_1 != 0 && DISABLED(TEMP_SENSOR_1_AS_REDUNDANT)
# error "TEMP_SENSOR_1 shouldn't be set with only 1 extruder."
# elif TEMP_SENSOR_2 != 0
# error "TEMP_SENSOR_2 shouldn't be set with only 1 extruder."
# elif TEMP_SENSOR_3 != 0
# error "TEMP_SENSOR_3 shouldn't be set with only 1 extruder."
# endif
# if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) && TEMP_SENSOR_1 == 0
# error "TEMP_SENSOR_1 is required with TEMP_SENSOR_1_AS_REDUNDANT."
# endif
/**
* Basic 2 - nozzle duplication mode
*/
# if ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
# if HOTENDS != 2
# error "DUAL_NOZZLE_DUPLICATION_MODE requires exactly 2 hotends."
# elif ENABLED(DUAL_X_CARRIAGE)
# error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with DUAL_X_CARRIAGE."
# elif ENABLED(SINGLENOZZLE)
# error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SINGLENOZZLE."
# elif ENABLED(MIXING_EXTRUDER)
# error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with MIXING_EXTRUDER."
# elif ENABLED(SWITCHING_EXTRUDER)
# error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SWITCHING_EXTRUDER."
# endif
# endif
/**
* Test Extruder Pins
*/
# if EXTRUDERS > 3
# if !PIN_EXISTS(E3_STEP) || !PIN_EXISTS(E3_DIR) || !PIN_EXISTS(E3_ENABLE)
# error "E3_STEP_PIN, E3_DIR_PIN, or E3_ENABLE_PIN not defined for this board."
# endif
# elif EXTRUDERS > 2
# if !PIN_EXISTS(E2_STEP) || !PIN_EXISTS(E2_DIR) || !PIN_EXISTS(E2_ENABLE)
# error "E2_STEP_PIN, E2_DIR_PIN, or E2_ENABLE_PIN not defined for this board."
# endif
# elif EXTRUDERS > 1
# if !PIN_EXISTS(E1_STEP) || !PIN_EXISTS(E1_DIR) || !PIN_EXISTS(E1_ENABLE)
# error "E1_STEP_PIN, E1_DIR_PIN, or E1_ENABLE_PIN not defined for this board."
# endif
# endif
/**
* Endstops
*/
# if DISABLED(USE_XMIN_PLUG) && DISABLED(USE_XMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _XMAX_ && Z2_USE_ENDSTOP <= _XMIN_)
2016-08-08 01:54:56 +02:00
# error "You must enable USE_XMIN_PLUG or USE_XMAX_PLUG."
2016-07-29 02:08:28 +02:00
# elif DISABLED(USE_YMIN_PLUG) && DISABLED(USE_YMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _YMAX_ && Z2_USE_ENDSTOP <= _YMIN_)
2016-08-08 01:54:56 +02:00
# error "You must enable USE_YMIN_PLUG or USE_YMAX_PLUG."
2016-07-29 02:08:28 +02:00
# elif DISABLED(USE_ZMIN_PLUG) && DISABLED(USE_ZMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _ZMAX_ && Z2_USE_ENDSTOP <= _ZMIN_)
2016-08-08 01:54:56 +02:00
# error "You must enable USE_ZMIN_PLUG or USE_ZMAX_PLUG."
# elif ENABLED(Z_DUAL_ENDSTOPS)
# if !Z2_USE_ENDSTOP
# error "You must set Z2_USE_ENDSTOP with Z_DUAL_ENDSTOPS."
# elif ENABLED(DELTA)
# error "Z_DUAL_ENDSTOPS is not compatible with DELTA."
# endif
2016-09-12 03:11:39 +02:00
# elif !IS_SCARA
2016-09-05 22:08:26 +02:00
# if X_HOME_DIR < 0 && DISABLED(USE_XMIN_PLUG)
# error "Enable USE_XMIN_PLUG when homing X to MIN."
# elif X_HOME_DIR > 0 && DISABLED(USE_XMAX_PLUG)
# error "Enable USE_XMAX_PLUG when homing X to MAX."
# elif Y_HOME_DIR < 0 && DISABLED(USE_YMIN_PLUG)
# error "Enable USE_YMIN_PLUG when homing Y to MIN."
# elif Y_HOME_DIR > 0 && DISABLED(USE_YMAX_PLUG)
# error "Enable USE_YMAX_PLUG when homing Y to MAX."
# elif Z_HOME_DIR < 0 && DISABLED(USE_ZMIN_PLUG)
# error "Enable USE_ZMIN_PLUG when homing Z to MIN."
# elif Z_HOME_DIR > 0 && DISABLED(USE_ZMAX_PLUG)
# error "Enable USE_ZMAX_PLUG when homing Z to MAX."
# endif
2016-07-29 02:08:28 +02:00
# endif
/**
* emergency - command parser
*/
2016-08-09 06:49:57 +02:00
# if ENABLED(EMERGENCY_PARSER) && defined(USBCON)
2016-07-29 02:08:28 +02:00
# error "EMERGENCY_PARSER does not work on boards with AT90USB processors (USBCON)."
# endif
2016-08-12 09:51:25 +02:00
/**
* I2C bus
*/
# if ENABLED(EXPERIMENTAL_I2CBUS) && I2C_SLAVE_ADDRESS > 0
# if I2C_SLAVE_ADDRESS < 8
# error "I2C_SLAVE_ADDRESS can't be less than 8. (Addresses 0 - 7 are reserved.)"
# elif I2C_SLAVE_ADDRESS > 127
# error "I2C_SLAVE_ADDRESS can't be over 127. (Only 7 bits allowed.)"
# endif
# endif
2016-09-12 06:33:09 +02:00
/**
* Make sure only one display is enabled
*
* Note : BQ_LCD_SMART_CONTROLLER = > REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
* REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER = > REPRAP_DISCOUNT_SMART_CONTROLLER
* SAV_3DGLCD = > U8GLIB_SH1106 = > ULTIMAKERCONTROLLER
* miniVIKI = > ULTIMAKERCONTROLLER
* VIKI2 = > ULTIMAKERCONTROLLER
* ELB_FULL_GRAPHIC_CONTROLLER = > ULTIMAKERCONTROLLER
* PANEL_ONE = > ULTIMAKERCONTROLLER
*/
# define COUNT_LCD_1 0
# if ENABLED(ULTIMAKERCONTROLLER) \
& & DISABLED ( SAV_3DGLCD ) & & DISABLED ( miniVIKI ) & & DISABLED ( VIKI2 ) \
& & DISABLED ( ELB_FULL_GRAPHIC_CONTROLLER ) & & DISABLED ( PANEL_ONE )
# define COUNT_LCD_2 INCREMENT(COUNT_LCD_1)
# else
# define COUNT_LCD_2 COUNT_LCD_1
# endif
# if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) && DISABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
# define COUNT_LCD_3 INCREMENT(COUNT_LCD_2)
# else
# define COUNT_LCD_3 COUNT_LCD_2
# endif
# if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && DISABLED(BQ_LCD_SMART_CONTROLLER)
# define COUNT_LCD_4 INCREMENT(COUNT_LCD_3)
# else
# define COUNT_LCD_4 COUNT_LCD_3
# endif
# if ENABLED(CARTESIO_UI)
# define COUNT_LCD_5 INCREMENT(COUNT_LCD_4)
# else
# define COUNT_LCD_5 COUNT_LCD_4
# endif
# if ENABLED(PANEL_ONE)
# define COUNT_LCD_6 INCREMENT(COUNT_LCD_5)
# else
# define COUNT_LCD_6 COUNT_LCD_5
# endif
# if ENABLED(MAKRPANEL)
# define COUNT_LCD_7 INCREMENT(COUNT_LCD_6)
# else
# define COUNT_LCD_7 COUNT_LCD_6
# endif
# if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
# define COUNT_LCD_8 INCREMENT(COUNT_LCD_7)
# else
# define COUNT_LCD_8 COUNT_LCD_7
# endif
# if ENABLED(VIKI2)
# define COUNT_LCD_9 INCREMENT(COUNT_LCD_8)
# else
# define COUNT_LCD_9 COUNT_LCD_8
# endif
# if ENABLED(miniVIKI)
# define COUNT_LCD_10 INCREMENT(COUNT_LCD_9)
# else
# define COUNT_LCD_10 COUNT_LCD_9
# endif
# if ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
# define COUNT_LCD_11 INCREMENT(COUNT_LCD_10)
# else
# define COUNT_LCD_11 COUNT_LCD_10
# endif
# if ENABLED(G3D_PANEL)
# define COUNT_LCD_12 INCREMENT(COUNT_LCD_11)
# else
# define COUNT_LCD_12 COUNT_LCD_11
# endif
# if ENABLED(MINIPANEL)
# define COUNT_LCD_13 INCREMENT(COUNT_LCD_12)
# else
# define COUNT_LCD_13 COUNT_LCD_12
# endif
# if ENABLED(REPRAPWORLD_KEYPAD)
# define COUNT_LCD_14 INCREMENT(COUNT_LCD_13)
# else
# define COUNT_LCD_14 COUNT_LCD_13
# endif
# if ENABLED(RIGIDBOT_PANEL)
# define COUNT_LCD_15 INCREMENT(COUNT_LCD_14)
# else
# define COUNT_LCD_15 COUNT_LCD_14
# endif
# if ENABLED(RA_CONTROL_PANEL)
# define COUNT_LCD_16 INCREMENT(COUNT_LCD_15)
# else
# define COUNT_LCD_16 COUNT_LCD_15
# endif
# if ENABLED(LCD_I2C_SAINSMART_YWROBOT)
# define COUNT_LCD_17 INCREMENT(COUNT_LCD_16)
# else
# define COUNT_LCD_17 COUNT_LCD_16
# endif
# if ENABLED(LCM1602)
# define COUNT_LCD_18 INCREMENT(COUNT_LCD_17)
# else
# define COUNT_LCD_18 COUNT_LCD_17
# endif
# if ENABLED(LCD_I2C_PANELOLU2)
# define COUNT_LCD_19 INCREMENT(COUNT_LCD_18)
# else
# define COUNT_LCD_19 COUNT_LCD_18
# endif
# if ENABLED(LCD_I2C_VIKI)
# define COUNT_LCD_20 INCREMENT(COUNT_LCD_19)
# else
# define COUNT_LCD_20 COUNT_LCD_19
# endif
# if ENABLED(U8GLIB_SSD1306)
# define COUNT_LCD_21 INCREMENT(COUNT_LCD_20)
# else
# define COUNT_LCD_21 COUNT_LCD_20
# endif
# if ENABLED(SAV_3DLCD)
# define COUNT_LCD_22 INCREMENT(COUNT_LCD_21)
# else
# define COUNT_LCD_22 COUNT_LCD_21
# endif
# if ENABLED(BQ_LCD_SMART_CONTROLLER)
# define COUNT_LCD_23 INCREMENT(COUNT_LCD_22)
# else
# define COUNT_LCD_23 COUNT_LCD_22
# endif
# if ENABLED(SAV_3DGLCD)
# define COUNT_LCD_24 INCREMENT(COUNT_LCD_23)
# else
# define COUNT_LCD_24 COUNT_LCD_23
# endif
# if COUNT_LCD_24 > 1
# error "Please select no more than one LCD controller option."
# endif
