SERVO_DEACTIVATION_DELAY => SERVO_DELAY

This commit is contained in:
Scott Lahteine 2016-06-23 14:33:29 -07:00
parent 61f34eec03
commit 03c70c1990
23 changed files with 134 additions and 186 deletions

View file

@ -1173,18 +1173,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -593,8 +593,6 @@
#error "Z_LATE_ENABLE can't be used with COREXZ." #error "Z_LATE_ENABLE can't be used with COREXZ."
#elif defined(X_HOME_RETRACT_MM) #elif defined(X_HOME_RETRACT_MM)
#error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM." #error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM."
#elif defined(PROBE_SERVO_DEACTIVATION_DELAY)
#error "PROBE_SERVO_DEACTIVATION_DELAY has been replaced with DEACTIVATE_SERVOS_AFTER_MOVE and SERVO_DEACTIVATION_DELAY."
#elif defined(BEEPER) #elif defined(BEEPER)
#error "BEEPER is now BEEPER_PIN. Please update your pins definitions." #error "BEEPER is now BEEPER_PIN. Please update your pins definitions."
#elif defined(SDCARDDETECT) #elif defined(SDCARDDETECT)
@ -635,6 +633,10 @@
#error "X_ENDSTOP_SERVO_NR and Y_ENDSTOP_SERVO_NR are deprecated and should be removed." #error "X_ENDSTOP_SERVO_NR and Y_ENDSTOP_SERVO_NR are deprecated and should be removed."
#elif defined(XY_TRAVEL_SPEED) #elif defined(XY_TRAVEL_SPEED)
#error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead." #error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead."
#elif defined(PROBE_SERVO_DEACTIVATION_DELAY)
#error "PROBE_SERVO_DEACTIVATION_DELAY is deprecated. Use DEACTIVATE_SERVOS_AFTER_MOVE instead."
#elif defined(SERVO_DEACTIVATION_DELAY)
#error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead."
#endif #endif
#endif //SANITYCHECK_H #endif //SANITYCHECK_H

View file

@ -1172,18 +1172,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1156,18 +1156,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1154,18 +1154,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1165,18 +1165,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1167,18 +1167,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1190,18 +1190,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1173,18 +1173,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1170,18 +1170,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
#define NUM_SERVOS 0 // DGlass3D - Servo index starts with 0 for M280 command #define NUM_SERVOS 0 // DGlass3D - Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1181,18 +1181,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1194,18 +1194,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1165,18 +1165,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1173,18 +1173,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1258,18 +1258,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1252,18 +1252,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1255,18 +1255,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1255,18 +1255,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1257,18 +1257,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1176,18 +1176,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -1167,18 +1167,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// //
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DELAY 300
// Servo deactivation // Servo deactivation
// //
// With this option servos are powered only during movement, then turned off to prevent jitter. // With this option servos are powered only during movement, then turned off to prevent jitter.
//#define DEACTIVATE_SERVOS_AFTER_MOVE //#define DEACTIVATE_SERVOS_AFTER_MOVE
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
// 300ms is a good value but you can try less delay.
// If the servo can't reach the requested position, increase it.
#define SERVO_DEACTIVATION_DELAY 300
#endif
/**********************************************************************\ /**********************************************************************\
* Support for a filament diameter sensor * Support for a filament diameter sensor
* Also allows adjustment of diameter at print time (vs at slicing) * Also allows adjustment of diameter at print time (vs at slicing)

View file

@ -21,50 +21,35 @@
*/ */
/** /**
servo.cpp - Interrupt driven Servo library for Arduino using 16 bit timers- Version 2 * servo.cpp - Interrupt driven Servo library for Arduino using 16 bit timers- Version 2
Copyright (c) 2009 Michael Margolis. All right reserved. * Copyright (c) 2009 Michael Margolis. All right reserved.
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public
License along with this library; if not, write to the Free Software
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/ */
/** /**
* A servo is activated by creating an instance of the Servo class passing the desired pin to the attach() method.
A servo is activated by creating an instance of the Servo class passing the desired pin to the attach() method. * The servos are pulsed in the background using the value most recently written using the write() method
The servos are pulsed in the background using the value most recently written using the write() method *
* Note that analogWrite of PWM on pins associated with the timer are disabled when the first servo is attached.
Note that analogWrite of PWM on pins associated with the timer are disabled when the first servo is attached. * Timers are seized as needed in groups of 12 servos - 24 servos use two timers, 48 servos will use four.
Timers are seized as needed in groups of 12 servos - 24 servos use two timers, 48 servos will use four. *
* The methods are:
The methods are: *
* Servo - Class for manipulating servo motors connected to Arduino pins.
Servo - Class for manipulating servo motors connected to Arduino pins. *
* attach(pin) - Attach a servo motor to an i/o pin.
attach(pin ) - Attaches a servo motor to an i/o pin. * attach(pin, min, max) - Attach to a pin, setting min and max values in microseconds
attach(pin, min, max ) - Attaches to a pin setting min and max values in microseconds * Default min is 544, max is 2400
default min is 544, max is 2400 *
* write() - Set the servo angle in degrees. (Invalid angles over MIN_PULSE_WIDTH are treated as µs.)
write() - Sets the servo angle in degrees. (invalid angle that is valid as pulse in microseconds is treated as microseconds) * writeMicroseconds() - Set the servo pulse width in microseconds.
writeMicroseconds() - Sets the servo pulse width in microseconds * move(pin, angle) - Sequence of attach(pin), write(angle), delay(SERVO_DELAY).
move(pin, angle) - Sequence of attach(pin), write(angle). * With DEACTIVATE_SERVOS_AFTER_MOVE it detaches after SERVO_DELAY.
With DEACTIVATE_SERVOS_AFTER_MOVE it waits SERVO_DEACTIVATION_DELAY and detaches. * read() - Get the last-written servo pulse width as an angle between 0 and 180.
read() - Gets the last written servo pulse width as an angle between 0 and 180. * readMicroseconds() - Get the last-written servo pulse width in microseconds.
readMicroseconds() - Gets the last written servo pulse width in microseconds. (was read_us() in first release) * attached() - Return true if a servo is attached.
attached() - Returns true if there is a servo attached. * detach() - Stop an attached servo from pulsing its i/o pin.
detach() - Stops an attached servos from pulsing its i/o pin. *
*/
*/
#include "Configuration.h" #include "Configuration.h"
#if HAS_SERVOS #if HAS_SERVOS
@ -238,6 +223,7 @@ static void finISR(timer16_Sequence_t timer) {
} }
#else //!WIRING #else //!WIRING
// For arduino - in future: call here to a currently undefined function to reset the timer // For arduino - in future: call here to a currently undefined function to reset the timer
UNUSED(timer);
#endif #endif
} }
@ -324,8 +310,8 @@ bool Servo::attached() { return servo_info[this->servoIndex].Pin.isActive; }
void Servo::move(int value) { void Servo::move(int value) {
if (this->attach(0) >= 0) { if (this->attach(0) >= 0) {
this->write(value); this->write(value);
delay(SERVO_DELAY);
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) #if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
delay(SERVO_DEACTIVATION_DELAY);
this->detach(); this->detach();
#endif #endif
} }

View file

@ -63,7 +63,7 @@
attached() - Returns true if there is a servo attached. attached() - Returns true if there is a servo attached.
detach() - Stops an attached servos from pulsing its i/o pin. detach() - Stops an attached servos from pulsing its i/o pin.
move(angle) - Sequence of attach(0), write(angle), move(angle) - Sequence of attach(0), write(angle),
With DEACTIVATE_SERVOS_AFTER_MOVE wait SERVO_DEACTIVATION_DELAY and detach. With DEACTIVATE_SERVOS_AFTER_MOVE wait SERVO_DELAY and detach.
*/ */
#ifndef servo_h #ifndef servo_h
@ -147,7 +147,7 @@ class Servo {
void writeMicroseconds(int value); // write pulse width in microseconds void writeMicroseconds(int value); // write pulse width in microseconds
void move(int value); // attach the servo, then move to value void move(int value); // attach the servo, then move to value
// if value is < 200 it is treated as an angle, otherwise as pulse width in microseconds // if value is < 200 it is treated as an angle, otherwise as pulse width in microseconds
// if DEACTIVATE_SERVOS_AFTER_MOVE wait SERVO_DEACTIVATION_DELAY, then detach // if DEACTIVATE_SERVOS_AFTER_MOVE wait SERVO_DELAY, then detach
int read(); // returns current pulse width as an angle between 0 and 180 degrees int read(); // returns current pulse width as an angle between 0 and 180 degrees
int readMicroseconds(); // returns current pulse width in microseconds for this servo (was read_us() in first release) int readMicroseconds(); // returns current pulse width in microseconds for this servo (was read_us() in first release)
bool attached(); // return true if this servo is attached, otherwise false bool attached(); // return true if this servo is attached, otherwise false