Merge pull request #3105 from esenapaj2/esenapaj2-patch-1
update example configurations
This commit is contained in:
commit
04b147645d
33 changed files with 261 additions and 160 deletions
|
@ -451,7 +451,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 180
|
#define BACK_PROBE_BED_POSITION 180
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Set the number of grid points per dimension.
|
// Set the number of grid points per dimension.
|
||||||
// You probably don't need more than 3 (squared=9).
|
// You probably don't need more than 3 (squared=9).
|
||||||
|
@ -506,6 +506,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
@ -585,10 +586,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
|
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
|
||||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {76.190476, 76.190476, 1600, 164}
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {76.190476, 76.190476, 1600, 164}
|
||||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {5000,5000,100,80000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {5000,5000,100,80000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 1750 //1500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 1750 //1500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 5000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
|
#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration in mm/s^2 for retracts
|
||||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||||
|
|
||||||
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||||
|
|
|
@ -61,6 +61,7 @@ Here are some standard links for getting your machine calibrated:
|
||||||
#define SERIAL_PORT 0
|
#define SERIAL_PORT 0
|
||||||
|
|
||||||
// This determines the communication speed of the printer
|
// This determines the communication speed of the printer
|
||||||
|
// :[2400,9600,19200,38400,57600,115200,250000]
|
||||||
#define BAUDRATE 250000
|
#define BAUDRATE 250000
|
||||||
|
|
||||||
// Enable the Bluetooth serial interface on AT90USB devices
|
// Enable the Bluetooth serial interface on AT90USB devices
|
||||||
|
@ -81,17 +82,27 @@ Here are some standard links for getting your machine calibrated:
|
||||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||||
|
|
||||||
// This defines the number of extruders
|
// This defines the number of extruders
|
||||||
|
// :[1,2,3,4]
|
||||||
#define EXTRUDERS 2
|
#define EXTRUDERS 2
|
||||||
|
|
||||||
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||||
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||||
|
// For the other hotends it is their distance from the extruder 0 hotend.
|
||||||
|
//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||||
|
//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||||
|
|
||||||
//// The following define selects which power supply you have. Please choose the one that matches your setup
|
//// The following define selects which power supply you have. Please choose the one that matches your setup
|
||||||
// 1 = ATX
|
// 1 = ATX
|
||||||
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
|
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
|
||||||
|
// :{1:'ATX',2:'X-Box 360'}
|
||||||
|
|
||||||
#define POWER_SUPPLY 1
|
#define POWER_SUPPLY 1
|
||||||
|
|
||||||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||||
#define PS_DEFAULT_OFF
|
#define PS_DEFAULT_OFF
|
||||||
|
|
||||||
|
// @section temperature
|
||||||
|
|
||||||
//===========================================================================
|
//===========================================================================
|
||||||
//============================= Thermal Settings ============================
|
//============================= Thermal Settings ============================
|
||||||
//===========================================================================
|
//===========================================================================
|
||||||
|
@ -231,6 +242,7 @@ Here are some standard links for getting your machine calibrated:
|
||||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||||
#endif // PIDTEMPBED
|
#endif // PIDTEMPBED
|
||||||
|
|
||||||
|
// @section extruder
|
||||||
|
|
||||||
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
||||||
//can be software-disabled for whatever purposes by
|
//can be software-disabled for whatever purposes by
|
||||||
|
@ -310,6 +322,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define DISABLE_Z_MIN_PROBE_ENDSTOP
|
//#define DISABLE_Z_MIN_PROBE_ENDSTOP
|
||||||
|
|
||||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||||
|
// :{0:'Low',1:'High'}
|
||||||
#define X_ENABLE_ON 0
|
#define X_ENABLE_ON 0
|
||||||
#define Y_ENABLE_ON 0
|
#define Y_ENABLE_ON 0
|
||||||
#define Z_ENABLE_ON 0
|
#define Z_ENABLE_ON 0
|
||||||
|
@ -322,20 +335,32 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define DISABLE_Z false
|
#define DISABLE_Z false
|
||||||
// Warn on display about possibly reduced accuracy
|
// Warn on display about possibly reduced accuracy
|
||||||
//#define DISABLE_REDUCED_ACCURACY_WARNING
|
//#define DISABLE_REDUCED_ACCURACY_WARNING
|
||||||
|
|
||||||
|
// @section extruder
|
||||||
|
|
||||||
#define DISABLE_E false // For all extruders
|
#define DISABLE_E false // For all extruders
|
||||||
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
||||||
|
|
||||||
|
// @section machine
|
||||||
|
|
||||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||||
#define INVERT_X_DIR true
|
#define INVERT_X_DIR true
|
||||||
#define INVERT_Y_DIR true
|
#define INVERT_Y_DIR true
|
||||||
#define INVERT_Z_DIR true
|
#define INVERT_Z_DIR true
|
||||||
|
|
||||||
|
// @section extruder
|
||||||
|
|
||||||
|
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||||
#define INVERT_E0_DIR false
|
#define INVERT_E0_DIR false
|
||||||
#define INVERT_E1_DIR true
|
#define INVERT_E1_DIR true
|
||||||
#define INVERT_E2_DIR false
|
#define INVERT_E2_DIR false
|
||||||
#define INVERT_E3_DIR false
|
#define INVERT_E3_DIR false
|
||||||
|
|
||||||
|
// @section homing
|
||||||
|
|
||||||
// ENDSTOP SETTINGS:
|
// ENDSTOP SETTINGS:
|
||||||
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
||||||
|
// :[-1,1]
|
||||||
#define X_HOME_DIR -1
|
#define X_HOME_DIR -1
|
||||||
#define Y_HOME_DIR -1
|
#define Y_HOME_DIR -1
|
||||||
#define Z_HOME_DIR -1
|
#define Z_HOME_DIR -1
|
||||||
|
@ -343,6 +368,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
|
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
|
||||||
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
||||||
|
|
||||||
|
// @section machine
|
||||||
|
|
||||||
// Travel limits after homing (units are in mm)
|
// Travel limits after homing (units are in mm)
|
||||||
#define X_MIN_POS 0
|
#define X_MIN_POS 0
|
||||||
#define Y_MIN_POS 0
|
#define Y_MIN_POS 0
|
||||||
|
@ -393,7 +420,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
// @section bedlevel
|
// @section bedlevel
|
||||||
|
|
||||||
|
|
||||||
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||||
//#define DEBUG_LEVELING_FEATURE
|
//#define DEBUG_LEVELING_FEATURE
|
||||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||||
|
@ -422,7 +448,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 180
|
#define BACK_PROBE_BED_POSITION 180
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Set the number of grid points per dimension.
|
// Set the number of grid points per dimension.
|
||||||
// You probably don't need more than 3 (squared=9).
|
// You probably don't need more than 3 (squared=9).
|
||||||
|
@ -477,6 +503,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
@ -528,6 +555,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#endif // AUTO_BED_LEVELING_FEATURE
|
#endif // AUTO_BED_LEVELING_FEATURE
|
||||||
|
|
||||||
|
|
||||||
|
// @section homing
|
||||||
|
|
||||||
// The position of the homing switches
|
// The position of the homing switches
|
||||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||||
|
@ -541,6 +570,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
// @section movement
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* MOVEMENT SETTINGS
|
* MOVEMENT SETTINGS
|
||||||
*/
|
*/
|
||||||
|
@ -552,18 +583,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
|
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
|
||||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {76.190476, 76.190476, 1600, 164}
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {76.190476, 76.190476, 1600, 164}
|
||||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {5000,5000,100,80000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {5000,5000,100,80000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 1750 //1500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 1750 //1500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 5000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
|
#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration in mm/s^2 for retracts
|
||||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||||
|
|
||||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
|
||||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
|
||||||
// For the other hotends it is their distance from the extruder 0 hotend.
|
|
||||||
//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
|
||||||
//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
|
||||||
|
|
||||||
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||||
#define DEFAULT_XYJERK 10 // (mm/sec)
|
#define DEFAULT_XYJERK 10 // (mm/sec)
|
||||||
#define DEFAULT_ZJERK 0.3 //0.4 // (mm/sec)
|
#define DEFAULT_ZJERK 0.3 //0.4 // (mm/sec)
|
||||||
|
@ -574,6 +599,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//============================= Additional Features ===========================
|
//============================= Additional Features ===========================
|
||||||
//=============================================================================
|
//=============================================================================
|
||||||
|
|
||||||
|
// @section more
|
||||||
|
|
||||||
// Custom M code points
|
// Custom M code points
|
||||||
#define CUSTOM_M_CODES
|
#define CUSTOM_M_CODES
|
||||||
#if ENABLED(CUSTOM_M_CODES)
|
#if ENABLED(CUSTOM_M_CODES)
|
||||||
|
@ -584,6 +611,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
// @section extras
|
||||||
|
|
||||||
// EEPROM
|
// EEPROM
|
||||||
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
|
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
|
||||||
|
@ -595,7 +623,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
#if ENABLED(EEPROM_SETTINGS)
|
#if ENABLED(EEPROM_SETTINGS)
|
||||||
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||||
#define EEPROM_CHITCHAT // please keep turned on if you can.
|
#define EEPROM_CHITCHAT // Please keep turned on if you can.
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
//
|
//
|
||||||
|
@ -615,6 +643,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||||
|
|
||||||
//==============================LCD and SD support=============================
|
//==============================LCD and SD support=============================
|
||||||
|
// @section lcd
|
||||||
|
|
||||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||||
// en, pl, fr, de, es, ru, bg, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test
|
// en, pl, fr, de, es, ru, bg, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test
|
||||||
|
@ -642,7 +671,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
||||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
||||||
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
|
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
|
||||||
|
|
||||||
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
|
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
|
||||||
// http://reprap.org/wiki/PanelOne
|
// http://reprap.org/wiki/PanelOne
|
||||||
//#define PANEL_ONE
|
//#define PANEL_ONE
|
||||||
|
@ -709,13 +737,19 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
||||||
//#define LCD_I2C_VIKI
|
//#define LCD_I2C_VIKI
|
||||||
|
|
||||||
|
// SSD1306 OLED generic display support
|
||||||
|
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
|
||||||
|
//#define U8GLIB_SSD1306
|
||||||
|
|
||||||
// Shift register panels
|
// Shift register panels
|
||||||
// ---------------------
|
// ---------------------
|
||||||
// 2 wire Non-latching LCD SR from:
|
// 2 wire Non-latching LCD SR from:
|
||||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||||
|
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
|
||||||
//#define SAV_3DLCD
|
//#define SAV_3DLCD
|
||||||
|
|
||||||
|
// @section extras
|
||||||
|
|
||||||
// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||||||
#define FAST_PWM_FAN
|
#define FAST_PWM_FAN
|
||||||
|
|
||||||
|
@ -739,7 +773,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
||||||
//#define PHOTOGRAPH_PIN 23
|
//#define PHOTOGRAPH_PIN 23
|
||||||
|
|
||||||
// SF send wrong arc g-codes when using Arc Point as fillet procedure
|
// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
|
||||||
//#define SF_ARC_FIX
|
//#define SF_ARC_FIX
|
||||||
|
|
||||||
// Support for the BariCUDA Paste Extruder.
|
// Support for the BariCUDA Paste Extruder.
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -347,7 +347,6 @@
|
||||||
//#define USE_SMALL_INFOFONT
|
//#define USE_SMALL_INFOFONT
|
||||||
#endif // DOGLCD
|
#endif // DOGLCD
|
||||||
|
|
||||||
|
|
||||||
// @section more
|
// @section more
|
||||||
|
|
||||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||||
|
@ -368,6 +367,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
@ -459,6 +459,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
|
||||||
#define FILAMENTCHANGE_ZADD 10
|
#define FILAMENTCHANGE_ZADD 10
|
||||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||||
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||||
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||||
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -433,7 +433,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
|
|
||||||
// @section bedlevel
|
// @section bedlevel
|
||||||
|
|
||||||
|
|
||||||
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||||
//#define DEBUG_LEVELING_FEATURE
|
//#define DEBUG_LEVELING_FEATURE
|
||||||
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||||
|
@ -462,7 +461,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Set the number of grid points per dimension.
|
// Set the number of grid points per dimension.
|
||||||
// You probably don't need more than 3 (squared=9).
|
// You probably don't need more than 3 (squared=9).
|
||||||
|
@ -517,6 +516,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -347,7 +347,6 @@
|
||||||
//#define USE_SMALL_INFOFONT
|
//#define USE_SMALL_INFOFONT
|
||||||
#endif // DOGLCD
|
#endif // DOGLCD
|
||||||
|
|
||||||
|
|
||||||
// @section more
|
// @section more
|
||||||
|
|
||||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||||
|
@ -368,6 +367,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
@ -459,6 +459,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
|
||||||
#define FILAMENTCHANGE_ZADD 10
|
#define FILAMENTCHANGE_ZADD 10
|
||||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||||
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||||
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||||
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -436,7 +436,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
// @section bedlevel
|
// @section bedlevel
|
||||||
|
|
||||||
|
|
||||||
#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||||
//#define DEBUG_LEVELING_FEATURE
|
//#define DEBUG_LEVELING_FEATURE
|
||||||
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||||
|
@ -520,6 +519,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
@ -717,7 +717,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
|
// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
|
||||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||||
//
|
//
|
||||||
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
|
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
|
||||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||||
|
|
||||||
// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
|
// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -347,7 +347,6 @@
|
||||||
#define USE_SMALL_INFOFONT
|
#define USE_SMALL_INFOFONT
|
||||||
#endif // DOGLCD
|
#endif // DOGLCD
|
||||||
|
|
||||||
|
|
||||||
// @section more
|
// @section more
|
||||||
|
|
||||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||||
|
@ -368,6 +367,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
@ -459,7 +459,7 @@ const unsigned int dropsegments = 5; //everything with less than this number of
|
||||||
#define FILAMENTCHANGE_ZADD 10
|
#define FILAMENTCHANGE_ZADD 10
|
||||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||||
#define AUTO_FILAMENT_CHANGE //This extrudes filament until you press the button on LCD
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||||
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||||
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||||
#endif
|
#endif
|
||||||
|
|
|
@ -330,7 +330,7 @@ Here are some standard links for getting your machine calibrated:
|
||||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||||
|
|
||||||
#if DISABLED(ENDSTOPPULLUPS)
|
#if DISABLED(ENDSTOPPULLUPS)
|
||||||
// define endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
||||||
//#define ENDSTOPPULLUP_XMAX
|
//#define ENDSTOPPULLUP_XMAX
|
||||||
//#define ENDSTOPPULLUP_YMAX
|
//#define ENDSTOPPULLUP_YMAX
|
||||||
//#define ENDSTOPPULLUP_ZMAX
|
//#define ENDSTOPPULLUP_ZMAX
|
||||||
|
|
|
@ -57,7 +57,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
|
|
@ -441,7 +441,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
// @section bedlevel
|
// @section bedlevel
|
||||||
|
|
||||||
|
|
||||||
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||||
//#define DEBUG_LEVELING_FEATURE
|
//#define DEBUG_LEVELING_FEATURE
|
||||||
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||||
|
@ -470,7 +469,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Set the number of grid points per dimension.
|
// Set the number of grid points per dimension.
|
||||||
// You probably don't need more than 3 (squared=9).
|
// You probably don't need more than 3 (squared=9).
|
||||||
|
@ -525,6 +524,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
|
|
@ -297,6 +297,9 @@ Here are some standard links for getting your machine calibrated:
|
||||||
// Uncomment this option to enable CoreXY kinematics
|
// Uncomment this option to enable CoreXY kinematics
|
||||||
//#define COREXY
|
//#define COREXY
|
||||||
|
|
||||||
|
// Uncomment this option to enable CoreXZ kinematics
|
||||||
|
//#define COREXZ
|
||||||
|
|
||||||
// Enable this option for Toshiba steppers
|
// Enable this option for Toshiba steppers
|
||||||
//#define CONFIG_STEPPERS_TOSHIBA
|
//#define CONFIG_STEPPERS_TOSHIBA
|
||||||
|
|
||||||
|
@ -460,7 +463,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Set the number of grid points per dimension.
|
// Set the number of grid points per dimension.
|
||||||
// You probably don't need more than 3 (squared=9).
|
// You probably don't need more than 3 (squared=9).
|
||||||
|
@ -515,6 +518,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
@ -729,6 +733,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
||||||
//#define RA_CONTROL_PANEL
|
//#define RA_CONTROL_PANEL
|
||||||
|
|
||||||
|
// The MakerLab Mini Panel with graphic controller and SD support
|
||||||
|
// http://reprap.org/wiki/Mini_panel
|
||||||
|
//#define MINIPANEL
|
||||||
|
|
||||||
// RigidBot Panel V1.0
|
// RigidBot Panel V1.0
|
||||||
// http://www.inventapart.com/
|
// http://www.inventapart.com/
|
||||||
#define RIGIDBOT_PANEL
|
#define RIGIDBOT_PANEL
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -296,13 +296,12 @@
|
||||||
|
|
||||||
#if ENABLED(SDSUPPORT)
|
#if ENABLED(SDSUPPORT)
|
||||||
|
|
||||||
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
|
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
|
||||||
// You can get round this by connecting a push button or single throw switch to the pin defined as SD_DETECT_PIN
|
// around this by connecting a push button or single throw switch to the pin defined
|
||||||
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
|
// as SD_DETECT_PIN in your board's pins definitions.
|
||||||
// be commented out otherwise
|
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
|
||||||
#ifndef ELB_FULL_GRAPHIC_CONTROLLER
|
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
|
||||||
#define SD_DETECT_INVERTED
|
#define SD_DETECT_INVERTED
|
||||||
#endif
|
|
||||||
|
|
||||||
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
||||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||||
|
@ -368,6 +367,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
|
|
@ -477,7 +477,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Set the number of grid points per dimension.
|
// Set the number of grid points per dimension.
|
||||||
// You probably don't need more than 3 (squared=9).
|
// You probably don't need more than 3 (squared=9).
|
||||||
|
@ -532,6 +532,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -347,7 +347,6 @@
|
||||||
//#define USE_SMALL_INFOFONT
|
//#define USE_SMALL_INFOFONT
|
||||||
#endif // DOGLCD
|
#endif // DOGLCD
|
||||||
|
|
||||||
|
|
||||||
// @section more
|
// @section more
|
||||||
|
|
||||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||||
|
@ -368,6 +367,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
@ -459,6 +459,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
|
||||||
#define FILAMENTCHANGE_ZADD 10
|
#define FILAMENTCHANGE_ZADD 10
|
||||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||||
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||||
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||||
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -461,10 +461,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
// @section bedlevel
|
// @section bedlevel
|
||||||
|
|
||||||
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
|
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||||
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
|
//#define DEBUG_LEVELING_FEATURE
|
||||||
|
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||||
|
|
||||||
#if ENABLED(ENABLE_AUTO_BED_LEVELING)
|
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
|
||||||
|
|
||||||
// There are 2 different ways to specify probing locations:
|
// There are 2 different ways to specify probing locations:
|
||||||
//
|
//
|
||||||
|
@ -543,6 +544,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
@ -591,7 +593,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//
|
//
|
||||||
//#define Z_MIN_PROBE_ENDSTOP
|
//#define Z_MIN_PROBE_ENDSTOP
|
||||||
|
|
||||||
#endif // ENABLE_AUTO_BED_LEVELING
|
#endif // AUTO_BED_LEVELING_FEATURE
|
||||||
|
|
||||||
|
|
||||||
// @section homing
|
// @section homing
|
||||||
|
@ -642,7 +644,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// Custom M code points
|
// Custom M code points
|
||||||
#define CUSTOM_M_CODES
|
#define CUSTOM_M_CODES
|
||||||
#if ENABLED(CUSTOM_M_CODES)
|
#if ENABLED(CUSTOM_M_CODES)
|
||||||
#if ENABLED(ENABLE_AUTO_BED_LEVELING)
|
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
|
||||||
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
|
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
|
||||||
#define Z_PROBE_OFFSET_RANGE_MIN -20
|
#define Z_PROBE_OFFSET_RANGE_MIN -20
|
||||||
#define Z_PROBE_OFFSET_RANGE_MAX 20
|
#define Z_PROBE_OFFSET_RANGE_MAX 20
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
|
|
@ -461,7 +461,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Set the number of grid points per dimension.
|
// Set the number of grid points per dimension.
|
||||||
// You probably don't need more than 3 (squared=9).
|
// You probably don't need more than 3 (squared=9).
|
||||||
|
@ -516,6 +516,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -347,7 +347,6 @@
|
||||||
//#define USE_SMALL_INFOFONT
|
//#define USE_SMALL_INFOFONT
|
||||||
#endif // DOGLCD
|
#endif // DOGLCD
|
||||||
|
|
||||||
|
|
||||||
// @section more
|
// @section more
|
||||||
|
|
||||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||||
|
@ -368,6 +367,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
@ -459,6 +459,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
|
||||||
#define FILAMENTCHANGE_ZADD 10
|
#define FILAMENTCHANGE_ZADD 10
|
||||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||||
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||||
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||||
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -441,7 +441,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
// @section bedlevel
|
// @section bedlevel
|
||||||
|
|
||||||
|
|
||||||
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||||
//#define DEBUG_LEVELING_FEATURE
|
//#define DEBUG_LEVELING_FEATURE
|
||||||
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||||
|
@ -470,7 +469,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Set the number of grid points per dimension.
|
// Set the number of grid points per dimension.
|
||||||
// You probably don't need more than 3 (squared=9).
|
// You probably don't need more than 3 (squared=9).
|
||||||
|
@ -525,6 +524,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
|
|
@ -506,7 +506,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
||||||
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Non-linear bed leveling will be used.
|
// Non-linear bed leveling will be used.
|
||||||
// Compensate by interpolating between the nearest four Z probe values for each point.
|
// Compensate by interpolating between the nearest four Z probe values for each point.
|
||||||
|
@ -563,6 +563,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
// Allen key retractable Z probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
// Allen key retractable Z probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
||||||
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
||||||
//#define Z_PROBE_ALLEN_KEY
|
//#define Z_PROBE_ALLEN_KEY
|
||||||
|
@ -724,7 +725,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
// delta speeds must be the same on xyz
|
// delta speeds must be the same on xyz
|
||||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {72.9, 72.9, 72.9, 291} // default steps per unit for BI v2.5 (cable drive)
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {72.9, 72.9, 72.9, 291} // default steps per unit for BI v2.5 (cable drive)
|
||||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 150} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 150} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||||
|
@ -856,6 +857,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
||||||
//#define RA_CONTROL_PANEL
|
//#define RA_CONTROL_PANEL
|
||||||
|
|
||||||
|
// The MakerLab Mini Panel with graphic controller and SD support
|
||||||
|
// http://reprap.org/wiki/Mini_panel
|
||||||
|
//#define MINIPANEL
|
||||||
|
|
||||||
// Delta calibration menu
|
// Delta calibration menu
|
||||||
// uncomment to add three points calibration menu option.
|
// uncomment to add three points calibration menu option.
|
||||||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -369,6 +369,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
@ -460,6 +461,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
|
||||||
#define FILAMENTCHANGE_ZADD 10
|
#define FILAMENTCHANGE_ZADD 10
|
||||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||||
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||||
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||||
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -476,14 +476,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
|
|
||||||
// @section bedlevel
|
// @section bedlevel
|
||||||
|
|
||||||
|
|
||||||
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||||
//#define DEBUG_LEVELING_FEATURE
|
//#define DEBUG_LEVELING_FEATURE
|
||||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||||
|
|
||||||
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
|
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
|
||||||
|
|
||||||
// There are 2 different ways to specify probing locations.
|
// There are 2 different ways to specify probing locations:
|
||||||
//
|
//
|
||||||
// - "grid" mode
|
// - "grid" mode
|
||||||
// Probe several points in a rectangular grid.
|
// Probe several points in a rectangular grid.
|
||||||
|
@ -507,7 +506,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
||||||
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Non-linear bed leveling will be used.
|
// Non-linear bed leveling will be used.
|
||||||
// Compensate by interpolating between the nearest four Z probe values for each point.
|
// Compensate by interpolating between the nearest four Z probe values for each point.
|
||||||
|
@ -564,6 +563,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
||||||
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
||||||
//#define Z_PROBE_ALLEN_KEY
|
//#define Z_PROBE_ALLEN_KEY
|
||||||
|
@ -725,7 +725,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
// delta speeds must be the same on xyz
|
// delta speeds must be the same on xyz
|
||||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 80, 760*1.1} // default steps per unit for Kossel (GT2, 20 tooth)
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 80, 760*1.1} // default steps per unit for Kossel (GT2, 20 tooth)
|
||||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 25} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 25} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||||
|
@ -857,6 +857,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
||||||
//#define RA_CONTROL_PANEL
|
//#define RA_CONTROL_PANEL
|
||||||
|
|
||||||
|
// The MakerLab Mini Panel with graphic controller and SD support
|
||||||
|
// http://reprap.org/wiki/Mini_panel
|
||||||
|
//#define MINIPANEL
|
||||||
|
|
||||||
// Delta calibration menu
|
// Delta calibration menu
|
||||||
// uncomment to add three points calibration menu option.
|
// uncomment to add three points calibration menu option.
|
||||||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||||||
|
@ -864,10 +868,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
// in ultralcd.cpp@lcd_delta_calibrate_menu()
|
// in ultralcd.cpp@lcd_delta_calibrate_menu()
|
||||||
//#define DELTA_CALIBRATION_MENU
|
//#define DELTA_CALIBRATION_MENU
|
||||||
|
|
||||||
// The MakerLab Mini Panel with graphic controller and SD support
|
|
||||||
// http://reprap.org/wiki/Mini_panel
|
|
||||||
//#define MINIPANEL
|
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* I2C Panels
|
* I2C Panels
|
||||||
*/
|
*/
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -349,7 +349,6 @@
|
||||||
//#define USE_SMALL_INFOFONT
|
//#define USE_SMALL_INFOFONT
|
||||||
#endif // DOGLCD
|
#endif // DOGLCD
|
||||||
|
|
||||||
|
|
||||||
// @section more
|
// @section more
|
||||||
|
|
||||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||||
|
@ -370,6 +369,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
@ -461,6 +461,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
|
||||||
#define FILAMENTCHANGE_ZADD 10
|
#define FILAMENTCHANGE_ZADD 10
|
||||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||||
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||||
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||||
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -476,7 +476,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
// @section bedlevel
|
// @section bedlevel
|
||||||
|
|
||||||
|
|
||||||
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||||
//#define DEBUG_LEVELING_FEATURE
|
//#define DEBUG_LEVELING_FEATURE
|
||||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||||
|
@ -507,7 +506,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
||||||
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Non-linear bed leveling will be used.
|
// Non-linear bed leveling will be used.
|
||||||
// Compensate by interpolating between the nearest four Z probe values for each point.
|
// Compensate by interpolating between the nearest four Z probe values for each point.
|
||||||
|
@ -564,6 +563,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
||||||
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
||||||
#define Z_PROBE_ALLEN_KEY
|
#define Z_PROBE_ALLEN_KEY
|
||||||
|
@ -729,7 +729,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// delta speeds must be the same on xyz
|
// delta speeds must be the same on xyz
|
||||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 80, 760*1.1} // default steps per unit for Kossel (GT2, 20 tooth)
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 80, 760*1.1} // default steps per unit for Kossel (GT2, 20 tooth)
|
||||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 25} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 25} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||||
|
@ -861,6 +861,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
||||||
//#define RA_CONTROL_PANEL
|
//#define RA_CONTROL_PANEL
|
||||||
|
|
||||||
|
// The MakerLab Mini Panel with graphic controller and SD support
|
||||||
|
// http://reprap.org/wiki/Mini_panel
|
||||||
|
//#define MINIPANEL
|
||||||
|
|
||||||
// Delta calibration menu
|
// Delta calibration menu
|
||||||
// uncomment to add three points calibration menu option.
|
// uncomment to add three points calibration menu option.
|
||||||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -348,7 +348,6 @@
|
||||||
//#define USE_SMALL_INFOFONT
|
//#define USE_SMALL_INFOFONT
|
||||||
#endif // DOGLCD
|
#endif // DOGLCD
|
||||||
|
|
||||||
|
|
||||||
// @section more
|
// @section more
|
||||||
|
|
||||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||||
|
@ -369,6 +368,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
@ -460,6 +460,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
|
||||||
#define FILAMENTCHANGE_ZADD 10
|
#define FILAMENTCHANGE_ZADD 10
|
||||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||||
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||||
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||||
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -463,7 +463,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
// @section bedlevel
|
// @section bedlevel
|
||||||
|
|
||||||
|
|
||||||
#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||||
//#define DEBUG_LEVELING_FEATURE
|
//#define DEBUG_LEVELING_FEATURE
|
||||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||||
|
@ -494,7 +493,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
||||||
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Non-linear bed leveling will be used.
|
// Non-linear bed leveling will be used.
|
||||||
// Compensate by interpolating between the nearest four Z probe values for each point.
|
// Compensate by interpolating between the nearest four Z probe values for each point.
|
||||||
|
@ -553,6 +552,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
||||||
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
||||||
#define Z_PROBE_ALLEN_KEY
|
#define Z_PROBE_ALLEN_KEY
|
||||||
|
@ -720,7 +720,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// delta speeds must be the same on xyz
|
// delta speeds must be the same on xyz
|
||||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {XYZ_STEPS, XYZ_STEPS, XYZ_STEPS, 184.8}
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {XYZ_STEPS, XYZ_STEPS, XYZ_STEPS, 184.8}
|
||||||
#define DEFAULT_MAX_FEEDRATE {200, 200, 200, 200} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {200, 200, 200, 200} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,9000} // X, Y, Z, E maximum start speed for accelerated moves.
|
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,9000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||||
|
@ -852,6 +852,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
||||||
//#define RA_CONTROL_PANEL
|
//#define RA_CONTROL_PANEL
|
||||||
|
|
||||||
|
// The MakerLab Mini Panel with graphic controller and SD support
|
||||||
|
// http://reprap.org/wiki/Mini_panel
|
||||||
|
//#define MINIPANEL
|
||||||
|
|
||||||
// Delta calibration menu
|
// Delta calibration menu
|
||||||
// uncomment to add three points calibration menu option.
|
// uncomment to add three points calibration menu option.
|
||||||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||||||
|
|
|
@ -56,7 +56,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -352,7 +352,6 @@
|
||||||
//#define USE_SMALL_INFOFONT
|
//#define USE_SMALL_INFOFONT
|
||||||
#endif // DOGLCD
|
#endif // DOGLCD
|
||||||
|
|
||||||
|
|
||||||
// @section more
|
// @section more
|
||||||
|
|
||||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||||
|
@ -373,6 +372,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
@ -464,6 +464,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
|
||||||
#define FILAMENTCHANGE_ZADD 10
|
#define FILAMENTCHANGE_ZADD 10
|
||||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||||
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||||
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||||
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -377,11 +377,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define Z_ENABLE_ON 0
|
#define Z_ENABLE_ON 0
|
||||||
#define E_ENABLE_ON 0 // For all extruders
|
#define E_ENABLE_ON 0 // For all extruders
|
||||||
|
|
||||||
// Disables axis when it's not being used.
|
// Disables axis stepper immediately when it's not being used.
|
||||||
// WARNING: When motors turn off there is a chance of losing position accuracy!
|
// WARNING: When motors turn off there is a chance of losing position accuracy!
|
||||||
#define DISABLE_X false
|
#define DISABLE_X false
|
||||||
#define DISABLE_Y false
|
#define DISABLE_Y false
|
||||||
#define DISABLE_Z false
|
#define DISABLE_Z false
|
||||||
|
// Warn on display about possibly reduced accuracy
|
||||||
|
//#define DISABLE_REDUCED_ACCURACY_WARNING
|
||||||
|
|
||||||
// @section extruder
|
// @section extruder
|
||||||
|
|
||||||
|
@ -439,16 +441,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
//===========================================================================
|
//===========================================================================
|
||||||
//=========================== Manual Bed Leveling ===========================
|
//============================ Mesh Bed Leveling ============================
|
||||||
//===========================================================================
|
//===========================================================================
|
||||||
|
|
||||||
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.
|
|
||||||
//#define MESH_BED_LEVELING // Enable mesh bed leveling.
|
//#define MESH_BED_LEVELING // Enable mesh bed leveling.
|
||||||
|
|
||||||
#if ENABLED(MANUAL_BED_LEVELING)
|
|
||||||
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
|
|
||||||
#endif // MANUAL_BED_LEVELING
|
|
||||||
|
|
||||||
#if ENABLED(MESH_BED_LEVELING)
|
#if ENABLED(MESH_BED_LEVELING)
|
||||||
#define MESH_MIN_X 10
|
#define MESH_MIN_X 10
|
||||||
#define MESH_MAX_X (X_MAX_POS - MESH_MIN_X)
|
#define MESH_MAX_X (X_MAX_POS - MESH_MIN_X)
|
||||||
|
@ -457,6 +454,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
|
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
|
||||||
#define MESH_NUM_Y_POINTS 3
|
#define MESH_NUM_Y_POINTS 3
|
||||||
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0.
|
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0.
|
||||||
|
|
||||||
|
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.
|
||||||
|
|
||||||
|
#if ENABLED(MANUAL_BED_LEVELING)
|
||||||
|
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
|
||||||
|
#endif // MANUAL_BED_LEVELING
|
||||||
|
|
||||||
#endif // MESH_BED_LEVELING
|
#endif // MESH_BED_LEVELING
|
||||||
|
|
||||||
//===========================================================================
|
//===========================================================================
|
||||||
|
@ -466,7 +470,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// @section bedlevel
|
// @section bedlevel
|
||||||
|
|
||||||
#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||||
#//define DEBUG_LEVELING_FEATURE
|
//#define DEBUG_LEVELING_FEATURE
|
||||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||||
|
|
||||||
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
|
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
|
||||||
|
@ -499,7 +503,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// Non-linear bed leveling will be used.
|
// Non-linear bed leveling will be used.
|
||||||
// Compensate by interpolating between the nearest four Z probe values for each point.
|
// Compensate by interpolating between the nearest four Z probe values for each point.
|
||||||
// Useful for deltas where the print surface may appear like a bowl or dome shape.
|
// Useful for deltas where the print surface may appear like a bowl or dome shape.
|
||||||
// Works best with ACCURATE_BED_LEVELING_POINTS 5 or higher.
|
// Works best with AUTO_BED_LEVELING_GRID_POINTS 5 or higher.
|
||||||
#define AUTO_BED_LEVELING_GRID_POINTS 7
|
#define AUTO_BED_LEVELING_GRID_POINTS 7
|
||||||
|
|
||||||
#else // !AUTO_BED_LEVELING_GRID
|
#else // !AUTO_BED_LEVELING_GRID
|
||||||
|
@ -635,7 +639,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {XYZ_STEPS, XYZ_STEPS, XYZ_STEPS, 158} // default steps per unit for PowerWasp
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {XYZ_STEPS, XYZ_STEPS, XYZ_STEPS, 158} // default steps per unit for PowerWasp
|
||||||
#define DEFAULT_MAX_FEEDRATE {200, 200, 200, 200} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {200, 200, 200, 200} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,9000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,9000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||||
|
@ -711,10 +715,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
//#define ULTRA_LCD //general LCD support, also 16x2
|
//#define ULTRA_LCD //general LCD support, also 16x2
|
||||||
//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
|
//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
|
||||||
//define SDSUPPORT // Enable SD Card Support in Hardware Console
|
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
|
||||||
// Changed behaviour! If you need SDSUPPORT uncomment it!
|
// Changed behaviour! If you need SDSUPPORT uncomment it!
|
||||||
//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
|
//#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
|
||||||
//#define SDEXTRASLOW // Use even slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
|
|
||||||
//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
|
//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
|
||||||
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
|
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
|
||||||
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
|
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
|
||||||
|
@ -734,13 +737,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD
|
// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD
|
||||||
// http://panucatt.com
|
// http://panucatt.com
|
||||||
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
|
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
|
||||||
//#define VIKI2
|
//#define VIKI2
|
||||||
//#define miniVIKI
|
//#define miniVIKI
|
||||||
|
|
||||||
// This is a new controller currently under development. https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
|
// This is a new controller currently under development. https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
|
||||||
//
|
//
|
||||||
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
|
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
|
||||||
//#define ELB_FULL_GRAPHIC_CONTROLLER
|
//#define ELB_FULL_GRAPHIC_CONTROLLER
|
||||||
//#define SD_DETECT_INVERTED
|
//#define SD_DETECT_INVERTED
|
||||||
|
|
||||||
|
@ -755,7 +758,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
|
// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
|
||||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||||
//
|
//
|
||||||
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
|
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
|
||||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||||
|
|
||||||
// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
|
// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
|
||||||
|
@ -791,7 +794,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define LCD_I2C_VIKI
|
//#define LCD_I2C_VIKI
|
||||||
|
|
||||||
// SSD1306 OLED generic display support
|
// SSD1306 OLED generic display support
|
||||||
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
|
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino
|
||||||
//#define U8GLIB_SSD1306
|
//#define U8GLIB_SSD1306
|
||||||
|
|
||||||
// Shift register panels
|
// Shift register panels
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -232,7 +232,13 @@
|
||||||
#define INVERT_E_STEP_PIN false
|
#define INVERT_E_STEP_PIN false
|
||||||
|
|
||||||
// Default stepper release if idle. Set to 0 to deactivate.
|
// Default stepper release if idle. Set to 0 to deactivate.
|
||||||
|
// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
|
||||||
|
// Time can be set by M18 and M84.
|
||||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||||
|
#define DISABLE_INACTIVE_X true
|
||||||
|
#define DISABLE_INACTIVE_Y true
|
||||||
|
#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
|
||||||
|
#define DISABLE_INACTIVE_E true
|
||||||
|
|
||||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||||
|
@ -344,7 +350,7 @@
|
||||||
// @section more
|
// @section more
|
||||||
|
|
||||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||||
//#define USE_WATCHDOG
|
#define USE_WATCHDOG
|
||||||
|
|
||||||
#if ENABLED(USE_WATCHDOG)
|
#if ENABLED(USE_WATCHDOG)
|
||||||
// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
|
// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
|
||||||
|
@ -380,7 +386,6 @@
|
||||||
#if ENABLED(ADVANCE)
|
#if ENABLED(ADVANCE)
|
||||||
#define EXTRUDER_ADVANCE_K .0
|
#define EXTRUDER_ADVANCE_K .0
|
||||||
#define D_FILAMENT 2.85
|
#define D_FILAMENT 2.85
|
||||||
#define STEPS_MM_E 836
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// @section extras
|
// @section extras
|
||||||
|
|
|
@ -472,7 +472,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Set the number of grid points per dimension.
|
// Set the number of grid points per dimension.
|
||||||
// You probably don't need more than 3 (squared=9).
|
// You probably don't need more than 3 (squared=9).
|
||||||
|
@ -527,6 +527,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
@ -605,7 +606,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
|
||||||
|
|
||||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {400, 400, 400, 163} // default steps per unit for ***** MakiBox A6 *****
|
#define DEFAULT_AXIS_STEPS_PER_UNIT {400, 400, 400, 163} // default steps per unit for ***** MakiBox A6 *****
|
||||||
#define DEFAULT_MAX_FEEDRATE {60, 60, 20, 45} // (mm/sec)
|
#define DEFAULT_MAX_FEEDRATE {60, 60, 20, 45} // (mm/sec)
|
||||||
#define DEFAULT_MAX_ACCELERATION {2000,2000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
#define DEFAULT_MAX_ACCELERATION {2000,2000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||||
|
|
||||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -296,10 +296,11 @@
|
||||||
|
|
||||||
#if ENABLED(SDSUPPORT)
|
#if ENABLED(SDSUPPORT)
|
||||||
|
|
||||||
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
|
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
|
||||||
// You can get round this by connecting a push button or single throw switch to the pin defined as SD_DETECT_PIN
|
// around this by connecting a push button or single throw switch to the pin defined
|
||||||
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
|
// as SD_DETECT_PIN in your board's pins definitions.
|
||||||
// be commented out otherwise
|
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
|
||||||
|
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
|
||||||
//#define SD_DETECT_INVERTED
|
//#define SD_DETECT_INVERTED
|
||||||
|
|
||||||
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
||||||
|
@ -346,7 +347,6 @@
|
||||||
//#define USE_SMALL_INFOFONT
|
//#define USE_SMALL_INFOFONT
|
||||||
#endif // DOGLCD
|
#endif // DOGLCD
|
||||||
|
|
||||||
|
|
||||||
// @section more
|
// @section more
|
||||||
|
|
||||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||||
|
@ -367,6 +367,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
@ -458,6 +459,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
|
||||||
#define FILAMENTCHANGE_ZADD 10
|
#define FILAMENTCHANGE_ZADD 10
|
||||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||||
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||||
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||||
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -431,7 +431,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
|
|
||||||
// @section bedlevel
|
// @section bedlevel
|
||||||
|
|
||||||
|
|
||||||
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||||
//#define DEBUG_LEVELING_FEATURE
|
//#define DEBUG_LEVELING_FEATURE
|
||||||
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||||
|
@ -460,7 +459,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
#define FRONT_PROBE_BED_POSITION 20
|
#define FRONT_PROBE_BED_POSITION 20
|
||||||
#define BACK_PROBE_BED_POSITION 170
|
#define BACK_PROBE_BED_POSITION 170
|
||||||
|
|
||||||
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
|
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||||
|
|
||||||
// Set the number of grid points per dimension.
|
// Set the number of grid points per dimension.
|
||||||
// You probably don't need more than 3 (squared=9).
|
// You probably don't need more than 3 (squared=9).
|
||||||
|
@ -515,6 +514,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||||
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||||
|
|
||||||
|
|
||||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||||
|
|
||||||
|
|
|
@ -52,7 +52,7 @@
|
||||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||||
* mintemp and maxtemp. Turn this off by excuting M109 without F*
|
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||||
*/
|
*/
|
||||||
|
@ -347,7 +347,6 @@
|
||||||
//#define USE_SMALL_INFOFONT
|
//#define USE_SMALL_INFOFONT
|
||||||
#endif // DOGLCD
|
#endif // DOGLCD
|
||||||
|
|
||||||
|
|
||||||
// @section more
|
// @section more
|
||||||
|
|
||||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||||
|
@ -368,6 +367,7 @@
|
||||||
//#define BABYSTEPPING
|
//#define BABYSTEPPING
|
||||||
#if ENABLED(BABYSTEPPING)
|
#if ENABLED(BABYSTEPPING)
|
||||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||||
|
//not implemented for CoreXY and deltabots!
|
||||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||||
#endif
|
#endif
|
||||||
|
@ -459,6 +459,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
|
||||||
#define FILAMENTCHANGE_ZADD 10
|
#define FILAMENTCHANGE_ZADD 10
|
||||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||||
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
||||||
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
||||||
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
Reference in a new issue