Merge pull request #2034 from thinkyhead/fixup_configs

Edit thermal runaway description
This commit is contained in:
Scott Lahteine 2015-05-07 21:46:05 -07:00
commit 0511ccda23
13 changed files with 325 additions and 403 deletions

View file

@ -270,42 +270,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
@ -411,7 +405,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define Z_MAX_POS 200 #define Z_MAX_POS 200
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -421,7 +415,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Mesh Bed Leveling ============================ //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -442,7 +436,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
// @section bedlevel // @section bedlevel

View file

@ -270,42 +270,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//=========================================================================== //===========================================================================
@ -410,7 +404,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define Z_MAX_POS 200 #define Z_MAX_POS 200
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -420,7 +414,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Manual Bed Leveling ========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -441,7 +435,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
// @section bedlevel // @section bedlevel

View file

@ -236,42 +236,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//=========================================================================== //===========================================================================
@ -349,7 +343,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define Z_MAX_POS 235 #define Z_MAX_POS 235
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -359,7 +353,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Manual Bed Leveling ========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -380,7 +374,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)

View file

@ -236,42 +236,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//=========================================================================== //===========================================================================
@ -349,7 +343,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define Z_MAX_POS 235 #define Z_MAX_POS 235
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -359,7 +353,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Manual Bed Leveling ========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -376,7 +370,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)

View file

@ -257,42 +257,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//=========================================================================== //===========================================================================
@ -370,7 +364,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#define Z_MAX_POS 180 #define Z_MAX_POS 180
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -380,7 +374,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Manual Bed Leveling ========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -401,7 +395,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)

View file

@ -286,42 +286,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//=========================================================================== //===========================================================================
@ -426,7 +420,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define Z_MAX_POS 200 #define Z_MAX_POS 200
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -436,7 +430,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Mesh Bed Leveling ============================ //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -457,7 +451,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
// @section bedlevel // @section bedlevel

View file

@ -288,42 +288,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//=========================================================================== //===========================================================================
@ -401,7 +395,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define Z_MAX_POS 225 #define Z_MAX_POS 225
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -411,7 +405,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Manual Bed Leveling ========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -432,7 +426,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)

View file

@ -256,42 +256,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//=========================================================================== //===========================================================================
@ -369,7 +363,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#define Z_MAX_POS 200 #define Z_MAX_POS 200
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -379,7 +373,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Manual Bed Leveling ========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -400,7 +394,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)

View file

@ -286,42 +286,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 120 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 120 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 4 // in degree Celsius
//=========================================================================== //===========================================================================
@ -399,7 +393,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#define Z_MAX_POS MANUAL_Z_HOME_POS #define Z_MAX_POS MANUAL_Z_HOME_POS
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -409,7 +403,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Manual Bed Leveling ========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -430,7 +424,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)

View file

@ -286,42 +286,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//=========================================================================== //===========================================================================
@ -399,7 +393,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#define Z_MAX_POS MANUAL_Z_HOME_POS #define Z_MAX_POS MANUAL_Z_HOME_POS
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -409,7 +403,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Manual Bed Leveling ========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -430,7 +424,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)

View file

@ -286,42 +286,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//=========================================================================== //===========================================================================
@ -399,7 +393,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define Z_MAX_POS MANUAL_Z_HOME_POS #define Z_MAX_POS MANUAL_Z_HOME_POS
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -409,7 +403,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Manual Bed Leveling ========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -430,7 +424,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) #define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)

View file

@ -256,42 +256,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//=========================================================================== //===========================================================================
@ -369,7 +363,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#define Z_MAX_POS 86 #define Z_MAX_POS 86
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -379,7 +373,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Manual Bed Leveling ========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -400,7 +394,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)

View file

@ -258,42 +258,36 @@ Here are some standard links for getting your machine calibrated:
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
//=========================================================================== //===========================================================================
//============================= Thermal Runaway Protection ================== //======================== Thermal Runaway Protection =======================
//=========================================================================== //===========================================================================
/*
This is a feature to protect your printer from burn up in flames if it has
a thermistor coming off place (this happened to a friend of mine recently and
motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature than actual. /**
The system will turn the heater on forever, burning up the filament and anything * Thermal Runaway Protection protects your printer from damage and fire if a
else around. * thermistor falls out or temperature sensors fail in any way.
*
After the temperature reaches the target for the first time, this feature will * The issue: If a thermistor falls out or a temperature sensor fails,
start measuring for how long the current temperature stays below the target * Marlin can no longer sense the actual temperature. Since a disconnected
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). * thermistor reads as a low temperature, the firmware will keep the heater on.
*
If it stays longer than _PERIOD, it means the thermistor temperature * The solution: Once the temperature reaches the target, start observing.
cannot catch up with the target, so something *may be* wrong. Then, to be on the * If the temperature stays too far below the target (hysteresis) for too long,
safe side, the system will he halt. * the firmware will halt as a safety precaution.
*
Bear in mind the count down will just start AFTER the first time the * Note that because the countdown starts only AFTER the temperature reaches
thermistor temperature is over the target, so you will have no problem if * the target, this will not catch a thermistor that is already disconnected
your extruder heater takes 2 minutes to hit the target on heating. * when the print starts!
*
*/ * To enable for all extruder heaters, uncomment the two defines below:
// If you want to enable this feature for all your extruder heaters, */
// uncomment the 2 defines below:
// Parameters for all extruder heaters // Parameters for all extruder heaters
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds #define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
// If you want to enable this feature for your bed heater, // To enable for the bed heater, uncomment the two defines below:
// uncomment the 2 defines below:
// Parameters for the bed heater // Parameters for the bed heater
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds #define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius #define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
//=========================================================================== //===========================================================================
@ -371,7 +365,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#define Z_MAX_POS 120 #define Z_MAX_POS 120
//=========================================================================== //===========================================================================
//============================= Filament Runout Sensor ====================== //========================= Filament Runout Sensor ==========================
//=========================================================================== //===========================================================================
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament //#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
@ -381,7 +375,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. //#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
//=========================================================================== //===========================================================================
//============================ Manual Bed Leveling ========================== //=========================== Manual Bed Leveling ===========================
//=========================================================================== //===========================================================================
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling // #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
@ -402,7 +396,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
#endif // MESH_BED_LEVELING #endif // MESH_BED_LEVELING
//=========================================================================== //===========================================================================
//============================= Bed Auto Leveling =========================== //============================ Bed Auto Leveling ============================
//=========================================================================== //===========================================================================
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)