fix 1 bug, add error messages

===============================================

make changes requested by reviewers

===============================================

add M43 test to Travis, fix EOL, remove trailing spaces
This commit is contained in:
Bob-the-Kuhn 2017-04-12 23:22:11 -05:00
parent 28fec61f92
commit 1acb84ba02
2 changed files with 10 additions and 8 deletions

View file

@ -328,7 +328,7 @@ script:
# RA_CONTROL_PANEL
#
- restore_configs
- opt_enable RA_CONTROL_PANEL
- opt_enable RA_CONTROL_PANEL PINS_DEBUGGING
- build_marlin
#
######## I2C LCD/PANELS ##############

View file

@ -5397,12 +5397,11 @@ inline void gcode_M42() {
#if !(NUM_SERVOS >= 1 && HAS_SERVO_0)
SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("SERVO not setup");
#elif !HAS_Z_SERVO_ENDSTOP
SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Z_ENDSTOP_SERVO_NR not setup");
#else
#if !defined(z_servo_angle)
const int z_servo_angle[2] = Z_SERVO_ANGLES;
#endif
uint8_t probe_index = code_seen('P') ? code_value_byte() : 0;
uint8_t probe_index = code_seen('P') ? code_value_byte() : Z_ENDSTOP_SERVO_NR;
SERIAL_PROTOCOLLNPGM("Servo probe test");
SERIAL_PROTOCOLLNPAIR(". using index: ", probe_index);
SERIAL_PROTOCOLLNPAIR(". deploy angle: ", z_servo_angle[0]);
@ -5418,7 +5417,6 @@ inline void gcode_M42() {
probe_inverting = Z_MIN_ENDSTOP_INVERTING;
#elif ENABLED(Z_MIN_PROBE_ENDSTOP)
#define PROBE_TEST_PIN Z_MIN_PROBE_PIN
SERIAL_PROTOCOLLNPAIR(". probe uses Z_MIN_PROBE_PIN: ", PROBE_TEST_PIN);
SERIAL_PROTOCOLLNPGM(". uses Z_MIN_PROBE_ENDSTOP_INVERTING (ignores Z_MIN_ENDSTOP_INVERTING)");
SERIAL_PROTOCOLPGM(". Z_MIN_PROBE_ENDSTOP_INVERTING: ");
@ -5443,7 +5441,7 @@ inline void gcode_M42() {
if (probe_inverting != deploy_state) SERIAL_PROTOCOLLNPGM("WARNING - INVERTING setting probably backwards");
refresh_cmd_timeout();
if (deploy_state != stow_state) {
SERIAL_PROTOCOLLNPGM("TLTouch detected"); // BLTouch clone?
SERIAL_PROTOCOLLNPGM("BLTouch clone detected");
if (deploy_state) {
SERIAL_PROTOCOLLNPGM(". DEPLOYED state: HIGH (logic 1)");
SERIAL_PROTOCOLLNPGM(". STOWED (triggered) state: LOW (logic 0)");
@ -5452,6 +5450,10 @@ inline void gcode_M42() {
SERIAL_PROTOCOLLNPGM(". DEPLOYED state: LOW (logic 0)");
SERIAL_PROTOCOLLNPGM(". STOWED (triggered) state: HIGH (logic 1)");
}
#if ENABLED(BLTOUCH)
SERIAL_PROTOCOLLNPGM("ERROR: BLTOUCH enabled - set this device up as a Z Servo Probe with inverting as true.");
#endif
}
else { // measure active signal length
servo[probe_index].move(z_servo_angle[0]); //deploy