Improve pulse timing and step reliability (#16128)
This commit is contained in:
parent
5f06f42ccd
commit
1bad8f1b17
5 changed files with 128 additions and 105 deletions
|
@ -1548,10 +1548,10 @@
|
|||
/**
|
||||
* Maximum stepping rate (in Hz) the stepper driver allows
|
||||
* If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
|
||||
* 5000000 : Maximum for TMC2xxx stepper drivers
|
||||
* 1000000 : Maximum for LV8729 stepper driver
|
||||
* 500000 : Maximum for A4988 stepper driver
|
||||
* 400000 : Maximum for TMC2xxx stepper drivers
|
||||
* 250000 : Maximum for DRV8825 stepper driver
|
||||
* 200000 : Maximum for LV8729 stepper driver
|
||||
* 150000 : Maximum for TB6600 stepper driver
|
||||
* 15000 : Maximum for TB6560 stepper driver
|
||||
*
|
||||
|
|
|
@ -595,11 +595,7 @@
|
|||
#elif HAS_DRIVER(A4988) || HAS_DRIVER(A5984)
|
||||
#define MINIMUM_STEPPER_PULSE 1
|
||||
#elif TRINAMICS
|
||||
#if ENABLED(LIN_ADVANCE) && (HAS_TMC_STANDALONE_E_DRIVER || (HAS_TMC_E_DRIVER && DISABLED(SQUARE_WAVE_STEPPING)))
|
||||
#define MINIMUM_STEPPER_PULSE 1
|
||||
#else
|
||||
#define MINIMUM_STEPPER_PULSE 0
|
||||
#endif
|
||||
#elif HAS_DRIVER(LV8729)
|
||||
#define MINIMUM_STEPPER_PULSE 0
|
||||
#else
|
||||
|
@ -612,14 +608,14 @@
|
|||
#define MAXIMUM_STEPPER_RATE 15000
|
||||
#elif HAS_DRIVER(TB6600)
|
||||
#define MAXIMUM_STEPPER_RATE 150000
|
||||
#elif HAS_DRIVER(LV8729)
|
||||
#define MAXIMUM_STEPPER_RATE 200000
|
||||
#elif HAS_DRIVER(DRV8825)
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
#elif TRINAMICS
|
||||
#define MAXIMUM_STEPPER_RATE 400000
|
||||
#elif HAS_DRIVER(A4988)
|
||||
#define MAXIMUM_STEPPER_RATE 500000
|
||||
#elif HAS_DRIVER(LV8729)
|
||||
#define MAXIMUM_STEPPER_RATE 1000000
|
||||
#elif TRINAMICS
|
||||
#define MAXIMUM_STEPPER_RATE 5000000
|
||||
#else
|
||||
#define MAXIMUM_STEPPER_RATE 250000
|
||||
#endif
|
||||
|
|
|
@ -2551,11 +2551,3 @@ static_assert( _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2)
|
|||
#error "SHOW_REMAINING_TIME currently requires a Graphical LCD."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ENABLED(LIN_ADVANCE) && MINIMUM_STEPPER_PULSE < 1
|
||||
#if HAS_TMC_STANDALONE_E_DRIVER
|
||||
#error "LIN_ADVANCE with TMC standalone driver on extruder requires MIMIMUM_STEPPER_PULSE >= 1"
|
||||
#elif HAS_TMC_E_DRIVER && DISABLED(SQUARE_WAVE_STEPPING)
|
||||
#error "LIN_ADVANCE with TMC driver on extruder requires SQUARE_WAVE_STEPPING or MINIMUM_STEPPER_PULSE >= 1"
|
||||
#endif
|
||||
#endif
|
||||
|
|
|
@ -338,6 +338,17 @@ xyze_int8_t Stepper::count_direction{0};
|
|||
#if DISABLED(MIXING_EXTRUDER)
|
||||
#define E_APPLY_STEP(v,Q) E_STEP_WRITE(stepper_extruder, v)
|
||||
#endif
|
||||
#define TIMER_SETUP_NS (CYCLES_TO_NS(TIMER_READ_ADD_AND_STORE_CYCLES))
|
||||
|
||||
#define PULSE_HIGH_TICK_COUNT hal_timer_t(NS_TO_PULSE_TIMER_TICKS(_MIN_PULSE_HIGH_NS - _MIN(_MIN_PULSE_HIGH_NS, TIMER_SETUP_NS)))
|
||||
#define PULSE_LOW_TICK_COUNT hal_timer_t(NS_TO_PULSE_TIMER_TICKS(_MIN_PULSE_LOW_NS - _MIN(_MIN_PULSE_LOW_NS, TIMER_SETUP_NS)))
|
||||
|
||||
#define START_TIMED_PULSE(DIR) (end_tick_count = HAL_timer_get_count(PULSE_TIMER_NUM) + PULSE_##DIR##_TICK_COUNT)
|
||||
#define AWAIT_TIMED_PULSE() while (HAL_timer_get_count(PULSE_TIMER_NUM) < end_tick_count) { }
|
||||
#define START_HIGH_PULSE() START_TIMED_PULSE(HIGH)
|
||||
#define START_LOW_PULSE() START_TIMED_PULSE(LOW)
|
||||
#define AWAIT_HIGH_PULSE() AWAIT_TIMED_PULSE()
|
||||
#define AWAIT_LOW_PULSE() AWAIT_TIMED_PULSE()
|
||||
|
||||
void Stepper::wake_up() {
|
||||
// TCNT1 = 0;
|
||||
|
@ -1416,34 +1427,73 @@ void Stepper::stepper_pulse_phase_isr() {
|
|||
// Just update the value we will get at the end of the loop
|
||||
step_events_completed += events_to_do;
|
||||
|
||||
// Get the timer count and estimate the end of the pulse
|
||||
hal_timer_t pulse_end = HAL_timer_get_count(PULSE_TIMER_NUM) + hal_timer_t(MIN_PULSE_TICKS);
|
||||
|
||||
const hal_timer_t added_step_ticks = hal_timer_t(ADDED_STEP_TICKS);
|
||||
|
||||
// Take multiple steps per interrupt (For high speed moves)
|
||||
do {
|
||||
bool firstStep = true;
|
||||
xyze_bool_t step_needed{0};
|
||||
hal_timer_t end_tick_count;
|
||||
|
||||
do {
|
||||
#define _APPLY_STEP(AXIS) AXIS ##_APPLY_STEP
|
||||
#define _INVERT_STEP_PIN(AXIS) INVERT_## AXIS ##_STEP_PIN
|
||||
|
||||
// Determine if pulses are needed
|
||||
#define PULSE_PREP(AXIS) do{ \
|
||||
delta_error[_AXIS(AXIS)] += advance_dividend[_AXIS(AXIS)]; \
|
||||
step_needed[_AXIS(AXIS)] = (delta_error[_AXIS(AXIS)] >= 0); \
|
||||
if (step_needed[_AXIS(AXIS)]) { \
|
||||
count_position[_AXIS(AXIS)] += count_direction[_AXIS(AXIS)]; \
|
||||
delta_error[_AXIS(AXIS)] -= advance_divisor; \
|
||||
} \
|
||||
}while(0)
|
||||
|
||||
// Start an active pulse, if Bresenham says so, and update position
|
||||
#define PULSE_START(AXIS) do{ \
|
||||
delta_error[_AXIS(AXIS)] += advance_dividend[_AXIS(AXIS)]; \
|
||||
if (delta_error[_AXIS(AXIS)] >= 0) { \
|
||||
if (step_needed[_AXIS(AXIS)]) { \
|
||||
_APPLY_STEP(AXIS)(!_INVERT_STEP_PIN(AXIS), 0); \
|
||||
count_position[_AXIS(AXIS)] += count_direction[_AXIS(AXIS)]; \
|
||||
} \
|
||||
}while(0)
|
||||
|
||||
// Stop an active pulse, if any, and adjust error term
|
||||
#define PULSE_STOP(AXIS) do { \
|
||||
if (delta_error[_AXIS(AXIS)] >= 0) { \
|
||||
delta_error[_AXIS(AXIS)] -= advance_divisor; \
|
||||
if (step_needed[_AXIS(AXIS)]) { \
|
||||
_APPLY_STEP(AXIS)(_INVERT_STEP_PIN(AXIS), 0); \
|
||||
} \
|
||||
}while(0)
|
||||
|
||||
// Determine if pulses are needed
|
||||
#if HAS_X_STEP
|
||||
PULSE_PREP(X);
|
||||
#endif
|
||||
#if HAS_Y_STEP
|
||||
PULSE_PREP(Y);
|
||||
#endif
|
||||
#if HAS_Z_STEP
|
||||
PULSE_PREP(Z);
|
||||
#endif
|
||||
|
||||
#if EITHER(LIN_ADVANCE, MIXING_EXTRUDER)
|
||||
delta_error.e += advance_dividend.e;
|
||||
if (delta_error.e >= 0) {
|
||||
count_position.e += count_direction.e;
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
delta_error.e -= advance_divisor;
|
||||
// Don't step E here - But remember the number of steps to perform
|
||||
motor_direction(E_AXIS) ? --LA_steps : ++LA_steps;
|
||||
#else
|
||||
step_needed[E_AXIS] = delta_error.e >= 0;
|
||||
#endif
|
||||
}
|
||||
#elif HAS_E0_STEP
|
||||
PULSE_PREP(E);
|
||||
#endif
|
||||
|
||||
#if (MINIMUM_STEPPER_PULSE || MAXIMUM_STEPPER_RATE) && DISABLED(I2S_STEPPER_STREAM)
|
||||
if (firstStep)
|
||||
firstStep = false;
|
||||
else
|
||||
AWAIT_LOW_PULSE();
|
||||
#endif
|
||||
|
||||
// Pulse start
|
||||
#if HAS_X_STEP
|
||||
PULSE_START(X);
|
||||
|
@ -1455,24 +1505,10 @@ void Stepper::stepper_pulse_phase_isr() {
|
|||
PULSE_START(Z);
|
||||
#endif
|
||||
|
||||
// Pulse Extruders
|
||||
// Tick the E axis, correct error term and update position
|
||||
#if EITHER(LIN_ADVANCE, MIXING_EXTRUDER)
|
||||
delta_error.e += advance_dividend.e;
|
||||
if (delta_error.e >= 0) {
|
||||
count_position.e += count_direction.e;
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
delta_error.e -= advance_divisor;
|
||||
// Don't step E here - But remember the number of steps to perform
|
||||
motor_direction(E_AXIS) ? --LA_steps : ++LA_steps;
|
||||
#else // !LIN_ADVANCE && MIXING_EXTRUDER
|
||||
// Don't adjust delta_error.e here!
|
||||
// Being positive is the criteria for ending the pulse.
|
||||
E_STEP_WRITE(mixer.get_next_stepper(), !INVERT_E_STEP_PIN);
|
||||
#endif
|
||||
}
|
||||
#else // !LIN_ADVANCE && !MIXING_EXTRUDER
|
||||
#if HAS_E0_STEP
|
||||
#if DISABLED(LIN_ADVANCE)
|
||||
#if ENABLED(MIXING_EXTRUDER)
|
||||
if (step_needed[E_AXIS]) E_STEP_WRITE(mixer.get_next_stepper(), !INVERT_E_STEP_PIN);
|
||||
#elif HAS_E0_STEP
|
||||
PULSE_START(E);
|
||||
#endif
|
||||
#endif
|
||||
|
@ -1482,14 +1518,11 @@ void Stepper::stepper_pulse_phase_isr() {
|
|||
#endif
|
||||
|
||||
// TODO: need to deal with MINIMUM_STEPPER_PULSE over i2s
|
||||
#if MINIMUM_STEPPER_PULSE && DISABLED(I2S_STEPPER_STREAM)
|
||||
// Just wait for the requested pulse duration
|
||||
while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ }
|
||||
#if (MINIMUM_STEPPER_PULSE || MAXIMUM_STEPPER_RATE) && DISABLED(I2S_STEPPER_STREAM)
|
||||
START_HIGH_PULSE();
|
||||
AWAIT_HIGH_PULSE();
|
||||
#endif
|
||||
|
||||
// Add the delay needed to ensure the maximum driver rate is enforced
|
||||
if (signed(added_step_ticks) > 0) pulse_end += hal_timer_t(added_step_ticks);
|
||||
|
||||
// Pulse stop
|
||||
#if HAS_X_STEP
|
||||
PULSE_STOP(X);
|
||||
|
@ -1503,31 +1536,26 @@ void Stepper::stepper_pulse_phase_isr() {
|
|||
|
||||
#if DISABLED(LIN_ADVANCE)
|
||||
#if ENABLED(MIXING_EXTRUDER)
|
||||
|
||||
if (delta_error.e >= 0) {
|
||||
delta_error.e -= advance_divisor;
|
||||
E_STEP_WRITE(mixer.get_stepper(), INVERT_E_STEP_PIN);
|
||||
}
|
||||
|
||||
#else // !MIXING_EXTRUDER
|
||||
|
||||
#if HAS_E0_STEP
|
||||
PULSE_STOP(E);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#endif // !MIXING_EXTRUDER
|
||||
#endif // !LIN_ADVANCE
|
||||
|
||||
// Decrement the count of pending pulses to do
|
||||
--events_to_do;
|
||||
|
||||
// For minimum pulse time wait after stopping pulses also
|
||||
if (events_to_do) {
|
||||
// Just wait for the requested pulse duration
|
||||
while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ }
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
// Add to the value, the time that the pulse must be active (to be used on the next loop)
|
||||
pulse_end += hal_timer_t(MIN_PULSE_TICKS);
|
||||
#if (MINIMUM_STEPPER_PULSE || MAXIMUM_STEPPER_RATE) && DISABLED(I2S_STEPPER_STREAM)
|
||||
if (events_to_do) START_LOW_PULSE();
|
||||
#endif
|
||||
}
|
||||
|
||||
} while (events_to_do);
|
||||
} while (--events_to_do);
|
||||
}
|
||||
|
||||
// This is the last half of the stepper interrupt: This one processes and
|
||||
|
@ -1909,13 +1937,19 @@ uint32_t Stepper::stepper_block_phase_isr() {
|
|||
DELAY_NS(MINIMUM_STEPPER_POST_DIR_DELAY);
|
||||
#endif
|
||||
|
||||
// Get the timer count and estimate the end of the pulse
|
||||
hal_timer_t pulse_end = HAL_timer_get_count(PULSE_TIMER_NUM) + hal_timer_t(MIN_PULSE_TICKS);
|
||||
|
||||
const hal_timer_t added_step_ticks = hal_timer_t(ADDED_STEP_TICKS);
|
||||
//const hal_timer_t added_step_ticks = hal_timer_t(ADDED_STEP_TICKS);
|
||||
|
||||
// Step E stepper if we have steps
|
||||
bool firstStep = true;
|
||||
hal_timer_t end_tick_count;
|
||||
|
||||
while (LA_steps) {
|
||||
#if (MINIMUM_STEPPER_PULSE || MAXIMUM_STEPPER_RATE) && DISABLED(I2S_STEPPER_STREAM)
|
||||
if (firstStep)
|
||||
firstStep = false;
|
||||
else
|
||||
AWAIT_LOW_PULSE();
|
||||
#endif
|
||||
|
||||
// Set the STEP pulse ON
|
||||
#if ENABLED(MIXING_EXTRUDER)
|
||||
|
@ -1925,16 +1959,16 @@ uint32_t Stepper::stepper_block_phase_isr() {
|
|||
#endif
|
||||
|
||||
// Enforce a minimum duration for STEP pulse ON
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
// Just wait for the requested pulse duration
|
||||
while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ }
|
||||
#if (MINIMUM_STEPPER_PULSE || MAXIMUM_STEPPER_RATE)
|
||||
START_HIGH_PULSE();
|
||||
#endif
|
||||
|
||||
// Add the delay needed to ensure the maximum driver rate is enforced
|
||||
if (signed(added_step_ticks) > 0) pulse_end += hal_timer_t(added_step_ticks);
|
||||
|
||||
LA_steps < 0 ? ++LA_steps : --LA_steps;
|
||||
|
||||
#if (MINIMUM_STEPPER_PULSE || MAXIMUM_STEPPER_RATE)
|
||||
AWAIT_HIGH_PULSE();
|
||||
#endif
|
||||
|
||||
// Set the STEP pulse OFF
|
||||
#if ENABLED(MIXING_EXTRUDER)
|
||||
E_STEP_WRITE(mixer.get_stepper(), INVERT_E_STEP_PIN);
|
||||
|
@ -1944,13 +1978,9 @@ uint32_t Stepper::stepper_block_phase_isr() {
|
|||
|
||||
// For minimum pulse time wait before looping
|
||||
// Just wait for the requested pulse duration
|
||||
if (LA_steps) {
|
||||
while (HAL_timer_get_count(PULSE_TIMER_NUM) < pulse_end) { /* nada */ }
|
||||
#if MINIMUM_STEPPER_PULSE
|
||||
// Add to the value, the time that the pulse must be active (to be used on the next loop)
|
||||
pulse_end += hal_timer_t(MIN_PULSE_TICKS);
|
||||
#if (MINIMUM_STEPPER_PULSE || MAXIMUM_STEPPER_RATE)
|
||||
if (LA_steps) START_LOW_PULSE();
|
||||
#endif
|
||||
}
|
||||
} // LA_steps
|
||||
|
||||
return interval;
|
||||
|
|
|
@ -57,6 +57,7 @@
|
|||
//
|
||||
|
||||
#ifdef CPU_32_BIT
|
||||
#define TIMER_READ_ADD_AND_STORE_CYCLES 34UL
|
||||
|
||||
// The base ISR takes 792 cycles
|
||||
#define ISR_BASE_CYCLES 792UL
|
||||
|
@ -85,6 +86,7 @@
|
|||
#define ISR_STEPPER_CYCLES 16UL
|
||||
|
||||
#else
|
||||
#define TIMER_READ_ADD_AND_STORE_CYCLES 13UL
|
||||
|
||||
// The base ISR takes 752 cycles
|
||||
#define ISR_BASE_CYCLES 752UL
|
||||
|
@ -116,43 +118,32 @@
|
|||
|
||||
// Add time for each stepper
|
||||
#if HAS_X_STEP
|
||||
#define ISR_START_X_STEPPER_CYCLES ISR_START_STEPPER_CYCLES
|
||||
#define ISR_X_STEPPER_CYCLES ISR_STEPPER_CYCLES
|
||||
#else
|
||||
#define ISR_START_X_STEPPER_CYCLES 0UL
|
||||
#define ISR_X_STEPPER_CYCLES 0UL
|
||||
#endif
|
||||
#if HAS_Y_STEP
|
||||
#define ISR_START_Y_STEPPER_CYCLES ISR_START_STEPPER_CYCLES
|
||||
#define ISR_Y_STEPPER_CYCLES ISR_STEPPER_CYCLES
|
||||
#else
|
||||
#define ISR_START_Y_STEPPER_CYCLES 0UL
|
||||
#define ISR_Y_STEPPER_CYCLES 0UL
|
||||
#endif
|
||||
#if HAS_Z_STEP
|
||||
#define ISR_START_Z_STEPPER_CYCLES ISR_START_STEPPER_CYCLES
|
||||
#define ISR_Z_STEPPER_CYCLES ISR_STEPPER_CYCLES
|
||||
#else
|
||||
#define ISR_START_Z_STEPPER_CYCLES 0UL
|
||||
#define ISR_Z_STEPPER_CYCLES 0UL
|
||||
#endif
|
||||
|
||||
// E is always interpolated, even for mixing extruders
|
||||
#define ISR_START_E_STEPPER_CYCLES ISR_START_STEPPER_CYCLES
|
||||
#define ISR_E_STEPPER_CYCLES ISR_STEPPER_CYCLES
|
||||
|
||||
// If linear advance is disabled, the loop also handles them
|
||||
#if DISABLED(LIN_ADVANCE) && ENABLED(MIXING_EXTRUDER)
|
||||
#define ISR_START_MIXING_STEPPER_CYCLES ((MIXING_STEPPERS) * (ISR_START_STEPPER_CYCLES))
|
||||
#define ISR_MIXING_STEPPER_CYCLES ((MIXING_STEPPERS) * (ISR_STEPPER_CYCLES))
|
||||
#else
|
||||
#define ISR_START_MIXING_STEPPER_CYCLES 0UL
|
||||
#define ISR_MIXING_STEPPER_CYCLES 0UL
|
||||
#endif
|
||||
|
||||
// Calculate the minimum time to start all stepper pulses in the ISR loop
|
||||
#define MIN_ISR_START_LOOP_CYCLES (ISR_START_X_STEPPER_CYCLES + ISR_START_Y_STEPPER_CYCLES + ISR_START_Z_STEPPER_CYCLES + ISR_START_E_STEPPER_CYCLES + ISR_START_MIXING_STEPPER_CYCLES)
|
||||
|
||||
// And the total minimum loop time, not including the base
|
||||
#define MIN_ISR_LOOP_CYCLES (ISR_X_STEPPER_CYCLES + ISR_Y_STEPPER_CYCLES + ISR_Z_STEPPER_CYCLES + ISR_E_STEPPER_CYCLES + ISR_MIXING_STEPPER_CYCLES)
|
||||
|
||||
|
@ -170,14 +161,28 @@
|
|||
// adding the "start stepper pulse" code section execution cycles to account for that not all
|
||||
// pulses start at the beginning of the loop, so an extra time must be added to compensate so
|
||||
// the last generated pulse (usually the extruder stepper) has the right length
|
||||
#if HAS_DRIVER(LV8729) && MINIMUM_STEPPER_PULSE == 0
|
||||
#define MIN_PULSE_TICKS ((((PULSE_TIMER_TICKS_PER_US) + 1) / 2) + ((MIN_ISR_START_LOOP_CYCLES) / uint32_t(PULSE_TIMER_PRESCALE)))
|
||||
#if MINIMUM_STEPPER_PULSE && MAXIMUM_STEPPER_RATE
|
||||
constexpr uint32_t _MIN_STEP_PERIOD_NS = 1000000000UL / MAXIMUM_STEPPER_RATE;
|
||||
constexpr uint32_t _MIN_PULSE_HIGH_NS = 1000UL * MINIMUM_STEPPER_PULSE;
|
||||
constexpr uint32_t _MIN_PULSE_LOW_NS = _MAX((_MIN_STEP_PERIOD_NS - _MIN(_MIN_STEP_PERIOD_NS, _MIN_PULSE_HIGH_NS)), _MIN_PULSE_HIGH_NS);
|
||||
#elif MINIMUM_STEPPER_PULSE
|
||||
// Assume 50% duty cycle
|
||||
constexpr uint32_t _MIN_STEP_PERIOD_NS = 1000000000UL / MAXIMUM_STEPPER_RATE;
|
||||
constexpr uint32_t _MIN_PULSE_HIGH_NS = 1000UL * MINIMUM_STEPPER_PULSE;
|
||||
constexpr uint32_t _MIN_PULSE_LOW_NS = _MIN_PULSE_HIGH_NS;
|
||||
#elif MAXIMUM_STEPPER_RATE
|
||||
// Assume 50% duty cycle
|
||||
constexpr uint32_t _MIN_PULSE_HIGH_NS = 500000000UL / MAXIMUM_STEPPER_RATE;
|
||||
constexpr uint32_t _MIN_PULSE_LOW_NS = _MIN_PULSE_HIGH_NS;
|
||||
#else
|
||||
#define MIN_PULSE_TICKS (((PULSE_TIMER_TICKS_PER_US) * uint32_t(MINIMUM_STEPPER_PULSE)) + ((MIN_ISR_START_LOOP_CYCLES) / uint32_t(PULSE_TIMER_PRESCALE)))
|
||||
#error "Expected at least one of MINIMUM_STEPPER_PULSE or MAXIMUM_STEPPER_RATE to be defined"
|
||||
#endif
|
||||
|
||||
// Calculate the extra ticks of the PULSE timer between step pulses
|
||||
#define ADDED_STEP_TICKS (((MIN_STEPPER_PULSE_CYCLES) / (PULSE_TIMER_PRESCALE)) - (MIN_PULSE_TICKS))
|
||||
// TODO: NS_TO_PULSE_TIMER_TICKS has some rounding issues:
|
||||
// 1. PULSE_TIMER_TICKS_PER_US rounds to an integer, which loses 20% of the count for a 2.5 MHz pulse tick (such as for LPC1768)
|
||||
// 2. The math currently rounds down to the closes tick. Perhaps should round up.
|
||||
constexpr uint32_t NS_TO_PULSE_TIMER_TICKS(uint32_t NS) { return PULSE_TIMER_TICKS_PER_US * (NS) / 1000UL; }
|
||||
#define CYCLES_TO_NS(CYC) (1000UL * (CYC) / ((F_CPU) / 1000000))
|
||||
|
||||
// But the user could be enforcing a minimum time, so the loop time is
|
||||
#define ISR_LOOP_CYCLES (ISR_LOOP_BASE_CYCLES + _MAX(MIN_STEPPER_PULSE_CYCLES, MIN_ISR_LOOP_CYCLES))
|
||||
|
|
Reference in a new issue