MIN_PROBE_EDGE replaces DELTA_PROBEABLE_RADIUS

This commit is contained in:
Scott Lahteine 2018-03-19 01:18:57 -05:00
parent eaefc1e410
commit 1d22609473
50 changed files with 52 additions and 331 deletions

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET
@ -865,8 +859,7 @@
* With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves.
*
* Note: Be sure to turn off auto-retract during filament change.
* Note: Current Zlift reset by G28 or G28 Z.
* Be sure to turn off auto-retract during filament change.
*
* Note that M207 / M208 / M209 settings are saved to EEPROM.
*

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -565,7 +565,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 400 }
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 400, 400}
/**
* Default Max Feed Rate (mm/s)

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET
@ -1413,11 +1407,6 @@
*/
//#define AUTO_REPORT_TEMPERATURES
/**
* Auto-report SdCard status with M27 S<seconds>
*/
//#define AUTO_REPORT_SD_STATUS
/**
* Include capabilities in M115 output
*/

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET
@ -780,7 +774,7 @@
// The minimum pulse width (in µs) for stepping a stepper.
// Set this if you find stepping unreliable, or if using a very fast CPU.
// 0 is OK for AVR, 0 is OK for A4989 drivers, 2 is needed for DRV8825 drivers
#define MINIMUM_STEPPER_PULSE 1 // (µs)
#define MINIMUM_STEPPER_PULSE 2 // (µs) DRV8825 on 32bit CPUs
// @section temperature

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -745,12 +745,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -750,12 +750,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -739,12 +739,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -705,7 +705,7 @@
#if ENABLED(BABYSTEPPING)
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
#define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
#define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
#define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
//#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
@ -739,12 +739,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -739,12 +739,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -739,12 +739,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -739,12 +739,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -739,12 +739,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -744,12 +744,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -739,12 +739,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -737,12 +737,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -738,12 +738,6 @@
// @section leveling
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#endif
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET

View file

@ -146,10 +146,8 @@
* a subsequent G or T leveling operation for backward compatibility.
*
* P1 Phase 1 Invalidate entire Mesh and continue with automatic generation of the Mesh data using
* the Z-Probe. Usually the probe can't reach all areas that the nozzle can reach. On
* Cartesian printers, points within the X_PROBE_OFFSET_FROM_EXTRUDER and Y_PROBE_OFFSET_FROM_EXTRUDER
* area cannot be automatically probed. For Delta printers the area in which DELTA_PROBEABLE_RADIUS
* and DELTA_PRINTABLE_RADIUS do not overlap will not be automatically probed.
* the Z-Probe. Usually the probe can't reach all areas that the nozzle can reach. For delta
* printers only the areas where the probe and nozzle can both reach will be automatically probed.
*
* Unreachable points will be handled in Phase 2 and Phase 3.
*

View file

@ -984,6 +984,20 @@
#endif
#endif // SKEW_CORRECTION
/**
* Set granular options based on the specific type of leveling
*/
#define UBL_SEGMENTED (ENABLED(AUTO_BED_LEVELING_UBL) && (ENABLED(DELTA)))
#define ABL_PLANAR (ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_3POINT))
#define ABL_GRID (ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR))
#define OLDSCHOOL_ABL (ABL_PLANAR || ABL_GRID)
#define HAS_ABL (OLDSCHOOL_ABL || ENABLED(AUTO_BED_LEVELING_UBL))
#define HAS_LEVELING (HAS_ABL || ENABLED(MESH_BED_LEVELING))
#define HAS_AUTOLEVEL (HAS_ABL && DISABLED(PROBE_MANUALLY))
#define HAS_MESH (ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL) || ENABLED(MESH_BED_LEVELING))
#define PLANNER_LEVELING (OLDSCHOOL_ABL || ENABLED(MESH_BED_LEVELING) || UBL_SEGMENTED || ENABLED(SKEW_CORRECTION))
#define HAS_PROBING_PROCEDURE (HAS_ABL || ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST))
/**
* Heater & Fan Pausing
*/
@ -1004,11 +1018,25 @@
#endif
/**
* Delta radius/rod trimmers/angle trimmers
* Bed Probing rectangular bounds
* These can be further constrained in code for Delta and SCARA
*/
#ifndef MIN_PROBE_EDGE
#define MIN_PROBE_EDGE 0
#endif
#if ENABLED(DELTA)
/**
* Delta radius/rod trimmers/angle trimmers
*/
#define _PROBE_RADIUS (DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#ifndef DELTA_CALIBRATION_RADIUS
#define DELTA_CALIBRATION_RADIUS DELTA_PRINTABLE_RADIUS - 10
#ifdef X_PROBE_OFFSET_FROM_EXTRUDER
#define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - MAX3(abs(X_PROBE_OFFSET_FROM_EXTRUDER), abs(Y_PROBE_OFFSET_FROM_EXTRUDER), abs(MIN_PROBE_EDGE)))
#else
#define DELTA_CALIBRATION_RADIUS _PROBE_RADIUS
#endif
#endif
#ifndef DELTA_ENDSTOP_ADJ
#define DELTA_ENDSTOP_ADJ { 0, 0, 0 }
@ -1022,59 +1050,36 @@
#ifndef DELTA_DIAGONAL_ROD_TRIM_TOWER
#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0, 0, 0}
#endif
#endif
/**
* Set granular options based on the specific type of leveling
*/
#define UBL_SEGMENTED (ENABLED(AUTO_BED_LEVELING_UBL) && (ENABLED(DELTA)))
#define ABL_PLANAR (ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_3POINT))
#define ABL_GRID (ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR))
#define OLDSCHOOL_ABL (ABL_PLANAR || ABL_GRID)
#define HAS_ABL (OLDSCHOOL_ABL || ENABLED(AUTO_BED_LEVELING_UBL))
#define HAS_LEVELING (HAS_ABL || ENABLED(MESH_BED_LEVELING))
#define HAS_AUTOLEVEL (HAS_ABL && DISABLED(PROBE_MANUALLY))
#define HAS_MESH (ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL) || ENABLED(MESH_BED_LEVELING))
#define PLANNER_LEVELING (OLDSCHOOL_ABL || ENABLED(MESH_BED_LEVELING) || UBL_SEGMENTED || ENABLED(SKEW_CORRECTION))
#define HAS_PROBING_PROCEDURE (HAS_ABL || ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST))
#if HAS_PROBING_PROCEDURE
#define PROBE_BED_WIDTH abs(RIGHT_PROBE_BED_POSITION - (LEFT_PROBE_BED_POSITION))
#define PROBE_BED_HEIGHT abs(BACK_PROBE_BED_POSITION - (FRONT_PROBE_BED_POSITION))
#endif
#if ENABLED(SEGMENT_LEVELED_MOVES) && !defined(LEVELED_SEGMENT_LENGTH)
#define LEVELED_SEGMENT_LENGTH 5
#endif
/**
* Bed Probing rectangular bounds
* These can be further constrained in code for Delta and SCARA
*/
#ifndef MIN_PROBE_EDGE
#define MIN_PROBE_EDGE 0
#endif
#if ENABLED(DELTA)
// Probing points may be verified at compile time within the radius
// using static_assert(HYPOT2(X2-X1,Y2-Y1)<=sq(DELTA_PRINTABLE_RADIUS),"bad probe point!")
// so that may be added to SanityCheck.h in the future.
#define _MIN_PROBE_X (X_CENTER - (DELTA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE)
#define _MIN_PROBE_Y (Y_CENTER - (DELTA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE)
#define _MAX_PROBE_X (X_CENTER + DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#define _MAX_PROBE_Y (Y_CENTER + DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#define _MIN_PROBE_X (X_CENTER - (_PROBE_RADIUS))
#define _MIN_PROBE_Y (Y_CENTER - (_PROBE_RADIUS))
#define _MAX_PROBE_X (X_CENTER + _PROBE_RADIUS)
#define _MAX_PROBE_Y (Y_CENTER + _PROBE_RADIUS)
#elif IS_SCARA
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#define _PROBE_RADIUS (SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#define _MIN_PROBE_X (X_CENTER - (SCARA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE)
#define _MIN_PROBE_Y (Y_CENTER - (SCARA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE)
#define _MAX_PROBE_X (X_CENTER + SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#define _MAX_PROBE_Y (Y_CENTER + SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#else
// Boundaries for Cartesian probing based on bed limits
#define _MIN_PROBE_X (max(X_MIN_BED + MIN_PROBE_EDGE, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define _MIN_PROBE_Y (max(Y_MIN_BED + MIN_PROBE_EDGE, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#define _MAX_PROBE_X (min(X_MAX_BED - (MIN_PROBE_EDGE), X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define _MAX_PROBE_Y (min(Y_MAX_BED - (MIN_PROBE_EDGE), Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#endif
#if ENABLED(SEGMENT_LEVELED_MOVES) && !defined(LEVELED_SEGMENT_LENGTH)
#define LEVELED_SEGMENT_LENGTH 5
#endif
// These may be overridden in Configuration.h if a smaller area is desired
@ -1116,10 +1121,8 @@
#define _MESH_MAX_X (min(X_MAX_BED - (MESH_INSET), X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define _MESH_MAX_Y (min(Y_MAX_BED - (MESH_INSET), Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#endif
#endif
// These may be overridden in Configuration.h if a smaller area is desired
#ifndef MESH_MIN_X
#define MESH_MIN_X _MESH_MIN_X

View file

@ -227,6 +227,8 @@
#error "LIN_ADVANCE (1.5) no longer uses LIN_ADVANCE_E_D_RATIO. Check your configuration."
#elif defined(NEOPIXEL_RGBW_LED)
#error "NEOPIXEL_RGBW_LED is now NEOPIXEL_LED. Please update your configuration."
#elif ENABLED(DELTA) && defined(DELTA_PROBEABLE_RADIUS)
#error "Remove DELTA_PROBEABLE_RADIUS and use MIN_PROBE_EDGE to inset the probe area instead."
#elif defined(UBL_MESH_INSET)
#error "UBL_MESH_INSET is now just MESH_INSET. Please update your configuration."
#elif defined(UBL_MESH_MIN_X) || defined(UBL_MESH_MIN_Y) || defined(UBL_MESH_MAX_X) || defined(UBL_MESH_MAX_Y)