Bring configs up to date

This commit is contained in:
Scott Lahteine 2019-11-21 04:48:18 -06:00
parent b904ba0f29
commit 20964ca7dc
57 changed files with 492 additions and 104 deletions

View file

@ -726,6 +726,11 @@
*/ */
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
#if ENABLED(LIMITED_MAX_FR_EDITING)
#define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
#endif
/** /**
* Default Max Acceleration (change/s) change = mm/s * Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves) * (Maximum start speed for accelerated moves)
@ -734,6 +739,11 @@
*/ */
#define DEFAULT_MAX_ACCELERATION { 2000, 2000, 50, 2000 } #define DEFAULT_MAX_ACCELERATION { 2000, 2000, 50, 2000 }
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
#define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
#endif
/** /**
* Default Acceleration (change/s) change = mm/s * Default Acceleration (change/s) change = mm/s
* Override with M204 * Override with M204
@ -759,6 +769,11 @@
#define DEFAULT_XJERK 20.0 #define DEFAULT_XJERK 20.0
#define DEFAULT_YJERK 20.0 #define DEFAULT_YJERK 20.0
#define DEFAULT_ZJERK 0.4 #define DEFAULT_ZJERK 0.4
//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
#if ENABLED(LIMITED_JERK_EDITING)
#define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
#endif
#endif #endif
#define DEFAULT_EJERK 5.0 // May be used by Linear Advance #define DEFAULT_EJERK 5.0 // May be used by Linear Advance

View file

@ -972,9 +972,6 @@
// Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
// especially with "vase mode" printing. Set too high and vases cannot be continued. // especially with "vase mode" printing. Set too high and vases cannot be continued.
#define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
//#define DEBUG_POWER_LOSS_RECOVERY // Debug informations on serial output
//#define SAVE_INFO_INTERVAL_MS 0 // Force SD recov. write interval, on each layer start if 0
#endif #endif
/** /**

View file

@ -971,9 +971,6 @@
// Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
// especially with "vase mode" printing. Set too high and vases cannot be continued. // especially with "vase mode" printing. Set too high and vases cannot be continued.
#define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
//#define DEBUG_POWER_LOSS_RECOVERY // Debug informations on serial output
//#define SAVE_INFO_INTERVAL_MS 0 // Force SD recov. write interval, on each layer start if 0
#endif #endif
/** /**

View file

@ -1105,6 +1105,7 @@
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
#define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor. #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor.
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
// Set one or more commands to execute on filament runout. // Set one or more commands to execute on filament runout.
// (After 'M412 H' Marlin will ask the host to handle the process.) // (After 'M412 H' Marlin will ask the host to handle the process.)

View file

@ -960,6 +960,8 @@
*/ */
//#define POWER_LOSS_RECOVERY //#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY) #if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

View file

@ -877,12 +877,13 @@
* on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
* *
* Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
* MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10. * and a minimum Z_HOMING_HEIGHT of 10.
*/ */
//#define TOUCH_MI_PROBE //#define TOUCH_MI_PROBE
#if ENABLED(TOUCH_MI_PROBE) #if ENABLED(TOUCH_MI_PROBE)
#define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
//#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
//#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
#endif #endif
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

View file

@ -877,12 +877,13 @@
* on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
* *
* Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
* MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10. * and a minimum Z_HOMING_HEIGHT of 10.
*/ */
//#define TOUCH_MI_PROBE //#define TOUCH_MI_PROBE
#if ENABLED(TOUCH_MI_PROBE) #if ENABLED(TOUCH_MI_PROBE)
#define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
//#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
//#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
#endif #endif
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

View file

@ -877,12 +877,13 @@
* on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
* *
* Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
* MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10. * and a minimum Z_HOMING_HEIGHT of 10.
*/ */
//#define TOUCH_MI_PROBE //#define TOUCH_MI_PROBE
#if ENABLED(TOUCH_MI_PROBE) #if ENABLED(TOUCH_MI_PROBE)
#define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts
//#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed
//#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu)
#endif #endif
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

View file

@ -1275,6 +1275,8 @@
#if ENABLED(LEVEL_BED_CORNERS) #if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
#define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners
#define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
//#define LEVEL_CENTER_TOO // Move to the center after the last corner //#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif #endif

View file

@ -482,6 +482,7 @@
#define HEATER_2_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5 #define BED_MINTEMP 5
// Above this temperature the heater will be switched off. // Above this temperature the heater will be switched off.
@ -492,6 +493,7 @@
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#if ENABLED(BED_AC) #if ENABLED(BED_AC)
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
#else #else
@ -1004,6 +1006,8 @@
* Specify a Probe position as { X, Y, Z } * Specify a Probe position as { X, Y, Z }
*/ */
#define NOZZLE_TO_PROBE_OFFSET { -22, 0, -1.5 } #define NOZZLE_TO_PROBE_OFFSET { -22, 0, -1.5 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10 #define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes // X and Y axis travel speed (mm/m) between probes
@ -1314,9 +1318,6 @@
#define GRID_MAX_POINTS_X 6 #define GRID_MAX_POINTS_X 6
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// The Z probe minimum outer margin (to validate G29 parameters).
#define MIN_PROBE_EDGE 10
// Probe along the Y axis, advancing X after each column // Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST //#define PROBE_Y_FIRST

View file

@ -909,7 +909,19 @@
// Add an 'M73' G-code to set the current percentage // Add an 'M73' G-code to set the current percentage
#define LCD_SET_PROGRESS_MANUALLY #define LCD_SET_PROGRESS_MANUALLY
#if HAS_PRINT_PROGRESS // Show the E position (filament used) during printing
//#define LCD_SHOW_E_TOTAL
#if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
//#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
//#define SHOW_REMAINING_TIME // Display estimated time to completion
#if ENABLED(SHOW_REMAINING_TIME)
//#define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation
//#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time
#endif
#endif
#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
//#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
#if ENABLED(LCD_PROGRESS_BAR) #if ENABLED(LCD_PROGRESS_BAR)
#define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar

View file

@ -938,7 +938,7 @@
#define SD_DETECT_INVERTED #define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place. #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
// Reverse SD sort to show "more recent" files first, according to the card's FAT. // Reverse SD sort to show "more recent" files first, according to the card's FAT.
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.

View file

@ -447,6 +447,8 @@
#define HEATER_1_MAXTEMP 410 #define HEATER_1_MAXTEMP 410
#define HEATER_2_MAXTEMP 410 #define HEATER_2_MAXTEMP 410
#define HEATER_3_MAXTEMP 410 #define HEATER_3_MAXTEMP 410
#define HEATER_4_MAXTEMP 410
#define HEATER_5_MAXTEMP 410
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
@ -2013,6 +2015,12 @@
// //
//#define MALYAN_LCD //#define MALYAN_LCD
//
// LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays
// See Configuration_adv.h for all configuration options.
//
//#define LULZBOT_TOUCH_UI
// //
// Third-party or vendor-customized controller interfaces. // Third-party or vendor-customized controller interfaces.
// Sources should be installed in 'src/lcd/extensible_ui'. // Sources should be installed in 'src/lcd/extensible_ui'.

View file

@ -655,8 +655,8 @@
//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated //#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
// minimum time in microseconds that a movement needs to take if the buffer is emptied. // Minimum time that a segment needs to take if the buffer is emptied
#define DEFAULT_MINSEGMENTTIME 20000 #define DEFAULT_MINSEGMENTTIME 20000 // (ms)
// If defined the movements slow down when the look ahead buffer is only half full // If defined the movements slow down when the look ahead buffer is only half full
#define SLOWDOWN #define SLOWDOWN
@ -855,11 +855,35 @@
#define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440
#endif #endif
// Include a page of printer information in the LCD Main Menu #if HAS_LCD_MENU
//#define LCD_INFO_MENU
#if ENABLED(LCD_INFO_MENU) // Include a page of printer information in the LCD Main Menu
//#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages //#define LCD_INFO_MENU
#endif #if ENABLED(LCD_INFO_MENU)
//#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
#endif
// BACK menu items keep the highlight at the top
//#define TURBO_BACK_MENU_ITEM
/**
* LED Control Menu
* Add LED Control to the LCD menu
*/
//#define LED_CONTROL_MENU
#if ENABLED(LED_CONTROL_MENU)
#define LED_COLOR_PRESETS // Enable the Preset Color menu option
#if ENABLED(LED_COLOR_PRESETS)
#define LED_USER_PRESET_RED 255 // User defined RED value
#define LED_USER_PRESET_GREEN 128 // User defined GREEN value
#define LED_USER_PRESET_BLUE 0 // User defined BLUE value
#define LED_USER_PRESET_WHITE 255 // User defined WHITE value
#define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity
//#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
#endif
#endif
#endif // HAS_LCD_MENU
// Scroll a longer status message into view // Scroll a longer status message into view
//#define STATUS_MESSAGE_SCROLLING //#define STATUS_MESSAGE_SCROLLING
@ -896,23 +920,6 @@
#endif #endif
#endif #endif
/**
* LED Control Menu
* Enable this feature to add LED Control to the LCD menu
*/
//#define LED_CONTROL_MENU
#if ENABLED(LED_CONTROL_MENU)
#define LED_COLOR_PRESETS // Enable the Preset Color menu option
#if ENABLED(LED_COLOR_PRESETS)
#define LED_USER_PRESET_RED 255 // User defined RED value
#define LED_USER_PRESET_GREEN 128 // User defined GREEN value
#define LED_USER_PRESET_BLUE 0 // User defined BLUE value
#define LED_USER_PRESET_WHITE 255 // User defined WHITE value
#define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity
//#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
#endif
#endif // LED_CONTROL_MENU
#if ENABLED(SDSUPPORT) #if ENABLED(SDSUPPORT)
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
@ -949,6 +956,7 @@
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
@ -1167,6 +1175,7 @@
//#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames
//#define STATUS_HEAT_PERCENT // Show heating in a progress bar //#define STATUS_HEAT_PERCENT // Show heating in a progress bar
//#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
//#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of PROGMEM.
// Frivolous Game Options // Frivolous Game Options
//#define MARLIN_BRICKOUT //#define MARLIN_BRICKOUT
@ -1244,8 +1253,12 @@
// Use a smaller font when labels don't fit buttons // Use a smaller font when labels don't fit buttons
#define TOUCH_UI_FIT_TEXT #define TOUCH_UI_FIT_TEXT
// Runtime language selection (otherwise LCD_LANGUAGE) // Allow language selection from menu at run-time (otherwise use LCD_LANGUAGE)
//#define TOUCH_UI_LANGUAGE_MENU //#define LCD_LANGUAGE_1 en
//#define LCD_LANGUAGE_2 fr
//#define LCD_LANGUAGE_3 de
//#define LCD_LANGUAGE_4 es
//#define LCD_LANGUAGE_5 it
// Use a numeric passcode for "Screen lock" keypad. // Use a numeric passcode for "Screen lock" keypad.
// (recommended for smaller displays) // (recommended for smaller displays)
@ -2433,6 +2446,13 @@
*/ */
#define EXTENDED_CAPABILITIES_REPORT #define EXTENDED_CAPABILITIES_REPORT
/**
* Expected Printer Check
* Add the M16 G-code to compare a string to the MACHINE_NAME.
* M16 with a non-matching string causes the printer to halt.
*/
//#define EXPECTED_PRINTER_CHECK
/** /**
* Disable all Volumetric extrusion options * Disable all Volumetric extrusion options
*/ */
@ -2487,6 +2507,13 @@
//#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
#endif #endif
/**
* Startup commands
*
* Execute certain G-code commands immediately after power-on.
*/
//#define STARTUP_COMMANDS "M17 Z"
/** /**
* G-code Macros * G-code Macros
* *

View file

@ -733,6 +733,11 @@
*/ */
#define DEFAULT_MAX_FEEDRATE { 360, 150, 30, 40 } #define DEFAULT_MAX_FEEDRATE { 360, 150, 30, 40 }
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
#if ENABLED(LIMITED_MAX_FR_EDITING)
#define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
#endif
/** /**
* Default Max Acceleration (change/s) change = mm/s * Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves) * (Maximum start speed for accelerated moves)
@ -741,6 +746,11 @@
*/ */
#define DEFAULT_MAX_ACCELERATION { 1200, 350, 100, 500 } #define DEFAULT_MAX_ACCELERATION { 1200, 350, 100, 500 }
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
#define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
#endif
/** /**
* Default Acceleration (change/s) change = mm/s * Default Acceleration (change/s) change = mm/s
* Override with M204 * Override with M204
@ -766,6 +776,11 @@
#define DEFAULT_XJERK 13.0 #define DEFAULT_XJERK 13.0
#define DEFAULT_YJERK 5.0 #define DEFAULT_YJERK 5.0
#define DEFAULT_ZJERK 0.4 #define DEFAULT_ZJERK 0.4
//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
#if ENABLED(LIMITED_JERK_EDITING)
#define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
#endif
#endif #endif
#define DEFAULT_EJERK 5.0 // May be used by Linear Advance #define DEFAULT_EJERK 5.0 // May be used by Linear Advance

View file

@ -733,6 +733,11 @@
*/ */
#define DEFAULT_MAX_FEEDRATE { 360, 150, 30, 40 } #define DEFAULT_MAX_FEEDRATE { 360, 150, 30, 40 }
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
#if ENABLED(LIMITED_MAX_FR_EDITING)
#define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
#endif
/** /**
* Default Max Acceleration (change/s) change = mm/s * Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves) * (Maximum start speed for accelerated moves)
@ -741,6 +746,11 @@
*/ */
#define DEFAULT_MAX_ACCELERATION { 1200, 350, 100, 500 } #define DEFAULT_MAX_ACCELERATION { 1200, 350, 100, 500 }
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
#define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
#endif
/** /**
* Default Acceleration (change/s) change = mm/s * Default Acceleration (change/s) change = mm/s
* Override with M204 * Override with M204
@ -766,6 +776,11 @@
#define DEFAULT_XJERK 13.0 #define DEFAULT_XJERK 13.0
#define DEFAULT_YJERK 5.0 #define DEFAULT_YJERK 5.0
#define DEFAULT_ZJERK 0.4 #define DEFAULT_ZJERK 0.4
//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
#if ENABLED(LIMITED_JERK_EDITING)
#define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
#endif
#endif #endif
#define DEFAULT_EJERK 5.0 // May be used by Linear Advance #define DEFAULT_EJERK 5.0 // May be used by Linear Advance

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *
@ -2512,6 +2515,13 @@
//#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
#endif #endif
/**
* Startup commands
*
* Execute certain G-code commands immediately after power-on.
*/
//#define STARTUP_COMMANDS "M17 Z"
/** /**
* G-code Macros * G-code Macros
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
#define FAN_KICKSTART_TIME 100 #define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -939,10 +939,17 @@
// Feedrate (mm/m) for the "accurate" probe of each point // Feedrate (mm/m) for the "accurate" probe of each point
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
// The number of probes to perform at each point. /**
// Set to 2 for a fast/slow probe, using the second probe result. * Multiple Probing
// Set to 3 or more for slow probes, averaging the results. *
* You may get improved results by probing 2 or more times.
* With EXTRA_PROBING the more atypical reading(s) will be disregarded.
*
* A total of 2 does fast/slow probes with a weighted average.
* A total of 3 or more adds more slow probes, taking the average.
*/
//#define MULTIPLE_PROBING 2 //#define MULTIPLE_PROBING 2
//#define EXTRA_PROBING 1
/** /**
* Z probes require clearance when deploying, stowing, and moving between * Z probes require clearance when deploying, stowing, and moving between

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
#define FAN_KICKSTART_TIME 100 #define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -731,6 +731,11 @@
*/ */
#define DEFAULT_MAX_FEEDRATE { 250, 250, 30, 55 } #define DEFAULT_MAX_FEEDRATE { 250, 250, 30, 55 }
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
#if ENABLED(LIMITED_MAX_FR_EDITING)
#define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
#endif
/** /**
* Default Max Acceleration (change/s) change = mm/s * Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves) * (Maximum start speed for accelerated moves)
@ -739,6 +744,11 @@
*/ */
#define DEFAULT_MAX_ACCELERATION { 2000, 2000, 120, 10000 } #define DEFAULT_MAX_ACCELERATION { 2000, 2000, 120, 10000 }
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
#define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
#endif
/** /**
* Default Acceleration (change/s) change = mm/s * Default Acceleration (change/s) change = mm/s
* Override with M204 * Override with M204
@ -764,6 +774,11 @@
#define DEFAULT_XJERK 8.0 #define DEFAULT_XJERK 8.0
#define DEFAULT_YJERK 8.0 #define DEFAULT_YJERK 8.0
#define DEFAULT_ZJERK 0.4 #define DEFAULT_ZJERK 0.4
//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
#if ENABLED(LIMITED_JERK_EDITING)
#define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
#endif
#endif #endif
#define DEFAULT_EJERK 5.0 // May be used by Linear Advance #define DEFAULT_EJERK 5.0 // May be used by Linear Advance

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
#define FAN_KICKSTART_TIME 100 #define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -731,6 +731,11 @@
*/ */
#define DEFAULT_MAX_FEEDRATE { 250, 250, 30, 55 } #define DEFAULT_MAX_FEEDRATE { 250, 250, 30, 55 }
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
#if ENABLED(LIMITED_MAX_FR_EDITING)
#define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
#endif
/** /**
* Default Max Acceleration (change/s) change = mm/s * Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves) * (Maximum start speed for accelerated moves)
@ -739,6 +744,11 @@
*/ */
#define DEFAULT_MAX_ACCELERATION { 2000, 2000, 120, 10000 } #define DEFAULT_MAX_ACCELERATION { 2000, 2000, 120, 10000 }
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
#define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
#endif
/** /**
* Default Acceleration (change/s) change = mm/s * Default Acceleration (change/s) change = mm/s
* Override with M204 * Override with M204
@ -764,6 +774,11 @@
#define DEFAULT_XJERK 8.0 #define DEFAULT_XJERK 8.0
#define DEFAULT_YJERK 8.0 #define DEFAULT_YJERK 8.0
#define DEFAULT_ZJERK 0.4 #define DEFAULT_ZJERK 0.4
//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
#if ENABLED(LIMITED_JERK_EDITING)
#define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
#endif
#endif #endif
#define DEFAULT_EJERK 5.0 // May be used by Linear Advance #define DEFAULT_EJERK 5.0 // May be used by Linear Advance

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
#define FAN_KICKSTART_TIME 100 #define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -2005,6 +2005,43 @@
#endif // K8200_VM8201 #endif // K8200_VM8201
//=============================================================================
//============================== OLED Displays ==============================
//=============================================================================
//
// SSD1306 OLED full graphics generic display
//
//#define U8GLIB_SSD1306
//
// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
//
//#define SAV_3DGLCD
#if ENABLED(SAV_3DGLCD)
#define U8GLIB_SSD1306
//#define U8GLIB_SH1106
#endif
//
// TinyBoy2 128x64 OLED / Encoder Panel
//
//#define OLED_PANEL_TINYBOY2
//
// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
// http://reprap.org/wiki/MKS_12864OLED
//
// Tiny, but very sharp OLED display
//
//#define MKS_12864OLED // Uses the SH1106 controller (default)
//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller
//
// Einstart S OLED SSD1306
//
//#define U8GLIB_SH1106_EINSTART
// //
// Overlord OLED display/controller with i2c buzzer and LEDs // Overlord OLED display/controller with i2c buzzer and LEDs
// //

View file

@ -303,6 +303,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
#define FAN_KICKSTART_TIME 500 #define FAN_KICKSTART_TIME 500
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -737,6 +737,11 @@
*/ */
#define DEFAULT_MAX_FEEDRATE { 700, 700, 100, 10000 } #define DEFAULT_MAX_FEEDRATE { 700, 700, 100, 10000 }
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
#if ENABLED(LIMITED_MAX_FR_EDITING)
#define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
#endif
/** /**
* Default Max Acceleration (change/s) change = mm/s * Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves) * (Maximum start speed for accelerated moves)
@ -745,6 +750,11 @@
*/ */
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 } #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
#define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
#endif
/** /**
* Default Acceleration (change/s) change = mm/s * Default Acceleration (change/s) change = mm/s
* Override with M204 * Override with M204
@ -903,11 +913,10 @@
/** /**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0). * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
* *
* In the following example the X and Y offsets are both positive: * In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10 *
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 * #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
* *
* +-- BACK ---+ * +-- BACK ---+
* | | * | |
@ -919,10 +928,10 @@
* | | * | |
* O-- FRONT --+ * O-- FRONT --+
* (0,0) * (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/ */
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
// Certain types of probes need to stay away from edges // Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10 #define MIN_PROBE_EDGE 10
@ -956,7 +965,7 @@
* *
* Use these settings to specify the distance (mm) to raise the probe (or * Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative) * lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. * probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here. * Only integer values >= 1 are valid here.
* *
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1214,12 +1223,6 @@
#define GRID_MAX_POINTS_X 3 #define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column // Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST //#define PROBE_Y_FIRST
@ -1273,19 +1276,6 @@
#endif // BED_LEVELING #endif // BED_LEVELING
/**
* Points to probe for all 3-point Leveling procedures.
* Override if the automatically selected points are inadequate.
*/
#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
//#define PROBE_PT_1_X 15
//#define PROBE_PT_1_Y 180
//#define PROBE_PT_2_X 15
//#define PROBE_PT_2_Y 20
//#define PROBE_PT_3_X 170
//#define PROBE_PT_3_Y 20
#endif
/** /**
* Add a bed leveling sub-menu for ABL or MBL. * Add a bed leveling sub-menu for ABL or MBL.
* Include a guided procedure if manual probing is enabled. * Include a guided procedure if manual probing is enabled.
@ -1593,10 +1583,10 @@
* *
* Select the language to display on the LCD. These languages are available: * Select the language to display on the LCD. These languages are available:
* *
* en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, jp-kana, * en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, it, jp_kana,
* ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test * ko_KR, nl, pl, pt, pt_br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
* *
* :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' }
*/ */
#define LCD_LANGUAGE en #define LCD_LANGUAGE en

View file

@ -214,7 +214,7 @@
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98
#endif #endif
// Show extra position information in M114 // Show extra position information with 'M114 D'
//#define M114_DETAIL //#define M114_DETAIL
// Show Temperature ADC value // Show Temperature ADC value
@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *
@ -379,6 +382,7 @@
#define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
#define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
#define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
//#define CASE_LIGHT_MAX_PWM 128 // Limit pwm
//#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu
//#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting.
//#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED.
@ -901,6 +905,18 @@
// Add an 'M73' G-code to set the current percentage // Add an 'M73' G-code to set the current percentage
//#define LCD_SET_PROGRESS_MANUALLY //#define LCD_SET_PROGRESS_MANUALLY
// Show the E position (filament used) during printing
//#define LCD_SHOW_E_TOTAL
#if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
//#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
//#define SHOW_REMAINING_TIME // Display estimated time to completion
#if ENABLED(SHOW_REMAINING_TIME)
//#define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation
//#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time
#endif
#endif
#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
//#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
#if ENABLED(LCD_PROGRESS_BAR) #if ENABLED(LCD_PROGRESS_BAR)
@ -1219,21 +1235,48 @@
//#define TOUCH_UI_PORTRAIT //#define TOUCH_UI_PORTRAIT
//#define TOUCH_UI_MIRRORED //#define TOUCH_UI_MIRRORED
// Enable UTF8 rendering capabilities. // UTF8 processing and rendering.
// Unsupported characters are shown as '?'.
//#define TOUCH_UI_USE_UTF8 //#define TOUCH_UI_USE_UTF8
#if ENABLED(TOUCH_UI_USE_UTF8) #if ENABLED(TOUCH_UI_USE_UTF8)
// Western accents support. These accented characters use
// combined bitmaps and require relatively little storage.
#define TOUCH_UI_UTF8_WESTERN_CHARSET #define TOUCH_UI_UTF8_WESTERN_CHARSET
#if ENABLED(TOUCH_UI_UTF8_WESTERN_CHARSET)
// Additional character groups. These characters require
// full bitmaps and take up considerable storage:
//#define TOUCH_UI_UTF8_SUPERSCRIPTS // ¹ ² ³
//#define TOUCH_UI_UTF8_COPYRIGHT // © ®
//#define TOUCH_UI_UTF8_GERMANIC // ß
//#define TOUCH_UI_UTF8_SCANDINAVIAN // Æ Ð Ø Þ æ ð ø þ
//#define TOUCH_UI_UTF8_PUNCTUATION // « » ¿ ¡
//#define TOUCH_UI_UTF8_CURRENCY // ¢ £ ¤ ¥
//#define TOUCH_UI_UTF8_ORDINALS // º ª
//#define TOUCH_UI_UTF8_MATHEMATICS // ± × ÷
//#define TOUCH_UI_UTF8_FRACTIONS // ¼ ½ ¾
//#define TOUCH_UI_UTF8_SYMBOLS // µ ¶ ¦ § ¬
#endif
#endif #endif
// When labels do not fit buttons, use smaller font // Use a smaller font when labels don't fit buttons
#define TOUCH_UI_FIT_TEXT #define TOUCH_UI_FIT_TEXT
// Runtime language selection (otherwise LCD_LANGUAGE) // Allow language selection from menu at run-time (otherwise use LCD_LANGUAGE)
//#define TOUCH_UI_LANGUAGE_MENU //#define LCD_LANGUAGE_1 en
//#define LCD_LANGUAGE_2 fr
//#define LCD_LANGUAGE_3 de
//#define LCD_LANGUAGE_4 es
//#define LCD_LANGUAGE_5 it
// Use a numeric passcode for "Screen lock" keypad. // Use a numeric passcode for "Screen lock" keypad.
// (recommended for smaller displays) // (recommended for smaller displays)
//#define TOUCH_UI_PASSCODE //#define TOUCH_UI_PASSCODE
// Output extra debug info for Touch UI events
//#define TOUCH_UI_DEBUG
// Developer menu (accessed by touching "About Printer" copyright text)
//#define TOUCH_UI_DEVELOPER_MENU
#endif #endif
// //
@ -1328,6 +1371,42 @@
// @section leveling // @section leveling
/**
* Points to probe for all 3-point Leveling procedures.
* Override if the automatically selected points are inadequate.
*/
#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
//#define PROBE_PT_1_X 15
//#define PROBE_PT_1_Y 180
//#define PROBE_PT_2_X 15
//#define PROBE_PT_2_Y 20
//#define PROBE_PT_3_X 170
//#define PROBE_PT_3_Y 20
#endif
/**
* Override MIN_PROBE_EDGE for each side of the build plate
* Useful to get probe points to exact positions on targets or
* to allow leveling to avoid plate clamps on only specific
* sides of the bed.
*
* If you are replacing the prior *_PROBE_BED_POSITION options,
* LEFT and FRONT values in most cases will map directly over
* RIGHT and REAR would be the inverse such as
* (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
*
* This will allow all positions to match at compilation, however
* should the probe position be modified with M851XY then the
* probe points will follow. This prevents any change from causing
* the probe to be unable to reach any points.
*/
#if PROBE_SELECTED && !IS_KINEMATIC
//#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
//#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
//#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
//#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
#endif
#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large // Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET //#define MESH_MIN_X MESH_INSET
@ -2074,7 +2153,7 @@
#define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down)
#define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down)
#define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper
#define X_CHAIN_POS 0 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI #define X_CHAIN_POS -1 // Position in SPI chain. (<=0 : Not in chain. 1 : Nearest MOSI)
#endif #endif
#if AXIS_DRIVER_TYPE_X2(L6470) #if AXIS_DRIVER_TYPE_X2(L6470)
@ -2082,7 +2161,7 @@
#define X2_OVERCURRENT 2000 #define X2_OVERCURRENT 2000
#define X2_STALLCURRENT 1500 #define X2_STALLCURRENT 1500
#define X2_MAX_VOLTAGE 127 #define X2_MAX_VOLTAGE 127
#define X2_CHAIN_POS 0 #define X2_CHAIN_POS -1
#endif #endif
#if AXIS_DRIVER_TYPE_Y(L6470) #if AXIS_DRIVER_TYPE_Y(L6470)
@ -2090,7 +2169,7 @@
#define Y_OVERCURRENT 2000 #define Y_OVERCURRENT 2000
#define Y_STALLCURRENT 1500 #define Y_STALLCURRENT 1500
#define Y_MAX_VOLTAGE 127 #define Y_MAX_VOLTAGE 127
#define Y_CHAIN_POS 0 #define Y_CHAIN_POS -1
#endif #endif
#if AXIS_DRIVER_TYPE_Y2(L6470) #if AXIS_DRIVER_TYPE_Y2(L6470)
@ -2098,7 +2177,7 @@
#define Y2_OVERCURRENT 2000 #define Y2_OVERCURRENT 2000
#define Y2_STALLCURRENT 1500 #define Y2_STALLCURRENT 1500
#define Y2_MAX_VOLTAGE 127 #define Y2_MAX_VOLTAGE 127
#define Y2_CHAIN_POS 0 #define Y2_CHAIN_POS -1
#endif #endif
#if AXIS_DRIVER_TYPE_Z(L6470) #if AXIS_DRIVER_TYPE_Z(L6470)
@ -2106,7 +2185,7 @@
#define Z_OVERCURRENT 2000 #define Z_OVERCURRENT 2000
#define Z_STALLCURRENT 1500 #define Z_STALLCURRENT 1500
#define Z_MAX_VOLTAGE 127 #define Z_MAX_VOLTAGE 127
#define Z_CHAIN_POS 0 #define Z_CHAIN_POS -1
#endif #endif
#if AXIS_DRIVER_TYPE_Z2(L6470) #if AXIS_DRIVER_TYPE_Z2(L6470)
@ -2114,7 +2193,7 @@
#define Z2_OVERCURRENT 2000 #define Z2_OVERCURRENT 2000
#define Z2_STALLCURRENT 1500 #define Z2_STALLCURRENT 1500
#define Z2_MAX_VOLTAGE 127 #define Z2_MAX_VOLTAGE 127
#define Z2_CHAIN_POS 0 #define Z2_CHAIN_POS -1
#endif #endif
#if AXIS_DRIVER_TYPE_Z3(L6470) #if AXIS_DRIVER_TYPE_Z3(L6470)
@ -2122,7 +2201,7 @@
#define Z3_OVERCURRENT 2000 #define Z3_OVERCURRENT 2000
#define Z3_STALLCURRENT 1500 #define Z3_STALLCURRENT 1500
#define Z3_MAX_VOLTAGE 127 #define Z3_MAX_VOLTAGE 127
#define Z3_CHAIN_POS 0 #define Z3_CHAIN_POS -1
#endif #endif
#if AXIS_DRIVER_TYPE_E0(L6470) #if AXIS_DRIVER_TYPE_E0(L6470)
@ -2130,7 +2209,7 @@
#define E0_OVERCURRENT 2000 #define E0_OVERCURRENT 2000
#define E0_STALLCURRENT 1500 #define E0_STALLCURRENT 1500
#define E0_MAX_VOLTAGE 127 #define E0_MAX_VOLTAGE 127
#define E0_CHAIN_POS 0 #define E0_CHAIN_POS -1
#endif #endif
#if AXIS_DRIVER_TYPE_E1(L6470) #if AXIS_DRIVER_TYPE_E1(L6470)
@ -2138,7 +2217,7 @@
#define E1_OVERCURRENT 2000 #define E1_OVERCURRENT 2000
#define E1_STALLCURRENT 1500 #define E1_STALLCURRENT 1500
#define E1_MAX_VOLTAGE 127 #define E1_MAX_VOLTAGE 127
#define E1_CHAIN_POS 0 #define E1_CHAIN_POS -1
#endif #endif
#if AXIS_DRIVER_TYPE_E2(L6470) #if AXIS_DRIVER_TYPE_E2(L6470)
@ -2146,7 +2225,7 @@
#define E2_OVERCURRENT 2000 #define E2_OVERCURRENT 2000
#define E2_STALLCURRENT 1500 #define E2_STALLCURRENT 1500
#define E2_MAX_VOLTAGE 127 #define E2_MAX_VOLTAGE 127
#define E2_CHAIN_POS 0 #define E2_CHAIN_POS -1
#endif #endif
#if AXIS_DRIVER_TYPE_E3(L6470) #if AXIS_DRIVER_TYPE_E3(L6470)
@ -2154,7 +2233,7 @@
#define E3_OVERCURRENT 2000 #define E3_OVERCURRENT 2000
#define E3_STALLCURRENT 1500 #define E3_STALLCURRENT 1500
#define E3_MAX_VOLTAGE 127 #define E3_MAX_VOLTAGE 127
#define E3_CHAIN_POS 0 #define E3_CHAIN_POS -1
#endif #endif
#if AXIS_DRIVER_TYPE_E4(L6470) #if AXIS_DRIVER_TYPE_E4(L6470)
@ -2162,7 +2241,7 @@
#define E4_OVERCURRENT 2000 #define E4_OVERCURRENT 2000
#define E4_STALLCURRENT 1500 #define E4_STALLCURRENT 1500
#define E4_MAX_VOLTAGE 127 #define E4_MAX_VOLTAGE 127
#define E4_CHAIN_POS 0 #define E4_CHAIN_POS -1
#endif #endif
#if AXIS_DRIVER_TYPE_E5(L6470) #if AXIS_DRIVER_TYPE_E5(L6470)
@ -2170,7 +2249,7 @@
#define E5_OVERCURRENT 2000 #define E5_OVERCURRENT 2000
#define E5_STALLCURRENT 1500 #define E5_STALLCURRENT 1500
#define E5_MAX_VOLTAGE 127 #define E5_MAX_VOLTAGE 127
#define E5_CHAIN_POS 0 #define E5_CHAIN_POS -1
#endif #endif
/** /**

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -1147,6 +1147,9 @@
// Before deploy/stow pause for user confirmation // Before deploy/stow pause for user confirmation
#define PAUSE_BEFORE_DEPLOY_STOW #define PAUSE_BEFORE_DEPLOY_STOW
#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
//#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
#endif
/** /**
* Enable one or more of the following if probing seems unreliable. * Enable one or more of the following if probing seems unreliable.

View file

@ -805,6 +805,11 @@
*/ */
#define DEFAULT_MAX_FEEDRATE { 100, 100, 100, 25 } #define DEFAULT_MAX_FEEDRATE { 100, 100, 100, 25 }
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
#if ENABLED(LIMITED_MAX_FR_EDITING)
#define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
#endif
/** /**
* Default Max Acceleration (change/s) change = mm/s * Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves) * (Maximum start speed for accelerated moves)
@ -813,6 +818,11 @@
*/ */
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 1000, 3000 } #define DEFAULT_MAX_ACCELERATION { 1000, 1000, 1000, 3000 }
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
#define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
#endif
/** /**
* Default Acceleration (change/s) change = mm/s * Default Acceleration (change/s) change = mm/s
* Override with M204 * Override with M204
@ -838,6 +848,11 @@
#define DEFAULT_XJERK 10.0 #define DEFAULT_XJERK 10.0
#define DEFAULT_YJERK DEFAULT_XJERK #define DEFAULT_YJERK DEFAULT_XJERK
#define DEFAULT_ZJERK DEFAULT_XJERK // Must be same as XY for delta #define DEFAULT_ZJERK DEFAULT_XJERK // Must be same as XY for delta
//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
#if ENABLED(LIMITED_JERK_EDITING)
#define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
#endif
#endif #endif
#define DEFAULT_EJERK 5.0 // May be used by Linear Advance #define DEFAULT_EJERK 5.0 // May be used by Linear Advance

View file

@ -2058,17 +2058,27 @@
#define E5_HYBRID_THRESHOLD 30 #define E5_HYBRID_THRESHOLD 30
/** /**
* Use StallGuard2 to home / probe X, Y, Z.
*
* TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode. * X, Y, and Z homing will always be done in spreadCycle mode.
* *
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity. * X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Higher values make the system LESS sensitive. * Use M914 X Y Z to set the stall threshold at runtime:
* Lower value make the system MORE sensitive. *
* Too low values can lead to false positives, while too high values will collide the axis without triggering. * Sensitivity TMC2209 Others
* It is advised to set X/Y/Z_HOME_BUMP_MM to 0. * HIGHEST 255 -64 (Too sensitive => False positive)
* M914 X/Y/Z to live tune the setting * LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
* SPI_ENDSTOPS *** Beta feature! *** TMC2130 Only ***
* Poll the driver through SPI to determine load when homing.
* Removes the need for a wire from DIAG1 to an endstop pin.
*
* IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when
* homing and adds a guard period for endstop triggering.
* *
* TMC2209 requires STEALTHCHOP enabled for SENSORLESS_HOMING * TMC2209 requires STEALTHCHOP enabled for SENSORLESS_HOMING
*/ */

View file

@ -817,6 +817,11 @@
*/ */
#define DEFAULT_MAX_FEEDRATE { 100, 100, 100, 25 } #define DEFAULT_MAX_FEEDRATE { 100, 100, 100, 25 }
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
#if ENABLED(LIMITED_MAX_FR_EDITING)
#define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
#endif
/** /**
* Default Max Acceleration (change/s) change = mm/s * Default Max Acceleration (change/s) change = mm/s
* (Maximum start speed for accelerated moves) * (Maximum start speed for accelerated moves)
@ -825,6 +830,11 @@
*/ */
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 1000, 3000 } #define DEFAULT_MAX_ACCELERATION { 1000, 1000, 1000, 3000 }
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
#define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
#endif
/** /**
* Default Acceleration (change/s) change = mm/s * Default Acceleration (change/s) change = mm/s
* Override with M204 * Override with M204
@ -850,6 +860,11 @@
#define DEFAULT_XJERK 10.0 #define DEFAULT_XJERK 10.0
#define DEFAULT_YJERK DEFAULT_XJERK #define DEFAULT_YJERK DEFAULT_XJERK
#define DEFAULT_ZJERK DEFAULT_XJERK // Must be same as XY for delta #define DEFAULT_ZJERK DEFAULT_XJERK // Must be same as XY for delta
//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
#if ENABLED(LIMITED_JERK_EDITING)
#define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
#endif
#endif #endif
#define DEFAULT_EJERK 5.0 // May be used by Linear Advance #define DEFAULT_EJERK 5.0 // May be used by Linear Advance

View file

@ -2059,17 +2059,27 @@
#define E5_HYBRID_THRESHOLD 30 #define E5_HYBRID_THRESHOLD 30
/** /**
* Use StallGuard2 to home / probe X, Y, Z.
*
* TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode. * X, Y, and Z homing will always be done in spreadCycle mode.
* *
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity. * X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Higher values make the system LESS sensitive. * Use M914 X Y Z to set the stall threshold at runtime:
* Lower value make the system MORE sensitive. *
* Too low values can lead to false positives, while too high values will collide the axis without triggering. * Sensitivity TMC2209 Others
* It is advised to set X/Y/Z_HOME_BUMP_MM to 0. * HIGHEST 255 -64 (Too sensitive => False positive)
* M914 X/Y/Z to live tune the setting * LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
* SPI_ENDSTOPS *** Beta feature! *** TMC2130 Only ***
* Poll the driver through SPI to determine load when homing.
* Removes the need for a wire from DIAG1 to an endstop pin.
*
* IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when
* homing and adds a guard period for endstop triggering.
* *
* TMC2209 requires STEALTHCHOP enabled for SENSORLESS_HOMING * TMC2209 requires STEALTHCHOP enabled for SENSORLESS_HOMING
*/ */

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *

View file

@ -290,6 +290,9 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// Some coolers may require a non-zero "off" state.
//#define FAN_OFF_PWM 1
/** /**
* PWM Fan Scaling * PWM Fan Scaling
* *