Merge pull request #1750 from thinkyhead/fixup_config

Bring all configs up to date

Marlin/Configuration.h

@@ -338,7 +338,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define DISABLE_E false // For all extruders
 #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
-// If you motor turns to wrong direction, you can invert it here:
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
 #define INVERT_X_DIR false
 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
@@ -428,7 +428,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
     // You probably don't need more than 3 (squared=9)
     #define AUTO_BED_LEVELING_GRID_POINTS 2
 
-
   #else  // !AUTO_BED_LEVELING_GRID
 
       // Arbitrary points to probe. A simple cross-product
@@ -442,7 +441,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 
   #endif // AUTO_BED_LEVELING_GRID
 
-
   // Offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
   #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // Probe on: -left  +right
@@ -572,7 +570,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 // See also language.h
 #define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Chose ONE of the next three charsets. This has to match your hardware. In case of a full graphic display this information is not important.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
 // To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
 // See also documentation/LCDLanguageFont.md
   #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
@@ -653,7 +651,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 //#define FAST_PWM_FAN
 
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
-// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
 //#define FAN_SOFT_PWM
 

Marlin/Configuration_adv.h

@@ -122,8 +122,7 @@
     #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
   #endif
 
-
+#endif // Z_DUAL_STEPPER_DRIVERS
-#endif
 
 // Same again but for Y Axis.
 //#define Y_DUAL_STEPPER_DRIVERS
@@ -242,6 +241,14 @@
 //#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
 
+#ifdef SDSUPPORT
+
+  // If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+  // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+  // in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+  // be commented out otherwise
+  #define SDCARDDETECTINVERTED
+
   #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
@@ -264,6 +271,8 @@
     //#define PROGRESS_MSG_ONCE
   #endif
 
+#endif // SDSUPPORT
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -300,7 +309,7 @@
   #define EXTRUDER_ADVANCE_K .0
   #define D_FILAMENT 2.85
   #define STEPS_MM_E 836
-#endif // ADVANCE
+#endif
 
 // Arc interpretation settings:
 #define MM_PER_ARC_SEGMENT 1
@@ -308,12 +317,6 @@
 
 const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
-// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
-// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
-// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
-// be commented out otherwise
-#define SDCARDDETECTINVERTED
-
 // Control heater 0 and heater 1 in parallel.
 //#define HEATERS_PARALLEL
 

Marlin/configurator/config/Configuration.h

@@ -329,13 +329,13 @@ your extruder heater takes 2 minutes to hit the target on heating.
   // #define ENDSTOPPULLUP_ZMIN
 #endif
 
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 //#define DISABLE_MAX_ENDSTOPS
 //#define DISABLE_MIN_ENDSTOPS
 
@@ -361,17 +361,17 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR true     // for Mendel set to false, for Orca set to true
+#define INVERT_X_DIR true
-#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
+#define INVERT_Y_DIR false
-#define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true
+#define INVERT_Z_DIR true
 
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.
-#define INVERT_E0_DIR false   // Direct drive extruder v9: true. Geared extruder: false
+#define INVERT_E0_DIR false
-#define INVERT_E1_DIR false   // Direct drive extruder v9: true. Geared extruder: false
+#define INVERT_E1_DIR false
-#define INVERT_E2_DIR false   // Direct drive extruder v9: true. Geared extruder: false
+#define INVERT_E2_DIR false
-#define INVERT_E3_DIR false   // Direct drive extruder v9: true. Geared extruder: false
+#define INVERT_E3_DIR false
 
 // @section homing
 
@@ -455,11 +455,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
     #define FRONT_PROBE_BED_POSITION 20
     #define BACK_PROBE_BED_POSITION 170
 
+    #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
+
     // Set the number of grid points per dimension
     // You probably don't need more than 3 (squared=9)
     #define AUTO_BED_LEVELING_GRID_POINTS 2
 
-
   #else  // !AUTO_BED_LEVELING_GRID
 
       // Arbitrary points to probe. A simple cross-product
@@ -473,11 +474,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #endif // AUTO_BED_LEVELING_GRID
 
-
   // Offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
-  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // -left  +right
+  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // Probe on: -left  +right
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // -front +behind
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Probe on: -front +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // -below (always!)
 
   #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
@@ -487,6 +487,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #define Z_RAISE_BEFORE_PROBING 15   //How much the extruder will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
+  #define Z_RAISE_AFTER_PROBING 15    //How much the extruder will be raised after the last probing point.
+
+//   #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
+                                                                            //Useful to retract a deployable probe.
                                                                            
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@@ -571,8 +575,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #ifdef CUSTOM_M_CODES
   #ifdef ENABLE_AUTO_BED_LEVELING
     #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-    #define Z_PROBE_OFFSET_RANGE_MIN -15
+    #define Z_PROBE_OFFSET_RANGE_MIN -20
-    #define Z_PROBE_OFFSET_RANGE_MAX -5
+    #define Z_PROBE_OFFSET_RANGE_MAX 20
   #endif
 #endif
 
@@ -604,13 +608,16 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 // @section lcd
 
 // Define your display language below. Replace (en) with your language code and uncomment.
-// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
+// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
 // See also language.h
 //#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Character based displays can have different extended charsets.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
-#define DISPLAY_CHARSET_HD44780_JAPAN     // "ääööüüß23°"
+// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
-//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
+// See also documentation/LCDLanguageFont.md
+  #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
+  //#define DISPLAY_CHARSET_HD44780_WESTERN
+  //#define DISPLAY_CHARSET_HD44780_CYRILLIC
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
@@ -623,6 +630,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+                                               // 0 to disable buzzer feedback  
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -687,7 +695,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define FAST_PWM_FAN
 
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
-// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
 //#define FAN_SOFT_PWM
 

Marlin/configurator/config/Configuration_adv.h

@@ -112,6 +112,30 @@
 // On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
 //#define Z_DUAL_STEPPER_DRIVERS
 
+#ifdef Z_DUAL_STEPPER_DRIVERS
+
+  // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+  // That way the machine is capable to align the bed during home, since both Z steppers are homed. 
+  // There is also an implementation of M666 (software endstops adjustment) to this feature.
+  // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+  // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+  // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+  // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+  // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+  #define Z_DUAL_ENDSTOPS
+
+  #ifdef Z_DUAL_ENDSTOPS
+    #define Z2_STEP_PIN E2_STEP_PIN           // Stepper to be used to Z2 axis.
+    #define Z2_DIR_PIN E2_DIR_PIN
+    #define Z2_ENABLE_PIN E2_ENABLE_PIN
+    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
+    const bool Z2_MAX_ENDSTOP_INVERTING = false;
+    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+  #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
 // Same again but for Y Axis.
 //#define Y_DUAL_STEPPER_DRIVERS
 
@@ -168,6 +192,7 @@
 #define X_HOME_RETRACT_MM 5
 #define Y_HOME_RETRACT_MM 5
 #define Z_HOME_RETRACT_MM 2
+#define HOMING_BUMP_DIVISOR {10, 10, 20}  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
 //#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
 
 // @section machine
@@ -231,8 +256,8 @@
 //===========================================================================
 
 #define ENCODER_RATE_MULTIPLIER         // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
-#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value
+#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
-#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
 //#define ENCODER_RATE_MULTIPLIER_DEBUG  // If defined, output the encoder steps per second value
 
 //#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
@@ -240,6 +265,14 @@
 
 // @section lcd
 
+#ifdef SDSUPPORT
+
+  // If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+  // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+  // in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+  // be commented out otherwise
+  #define SDCARDDETECTINVERTED
+
   #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
@@ -262,6 +295,8 @@
     //#define PROGRESS_MSG_ONCE
   #endif
 
+#endif // SDSUPPORT
+
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
@@ -298,12 +333,8 @@
 
 #ifdef ADVANCE
   #define EXTRUDER_ADVANCE_K .0
-
   #define D_FILAMENT 2.85
   #define STEPS_MM_E 836
-  #define EXTRUSION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
-  #define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUSION_AREA)
-
 #endif // ADVANCE
 
 // Arc interpretation settings:
@@ -312,14 +343,6 @@
 
 const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
-// @section lcd
-
-// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
-// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
-// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
-// be commented out otherwise
-#define SDCARDDETECTINVERTED
-
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.
@@ -333,7 +356,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 
 // The number of linear motions that can be in the plan at any give time.
 // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
-#if defined SDSUPPORT
+#ifdef SDSUPPORT
   #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
   #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
@@ -377,6 +400,139 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #endif
 #endif
 
+/******************************************************************************\
+ * enable this section if you have TMC26X motor drivers. 
+ * you need to import the TMC26XStepper library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_TMCDRIVER
+#ifdef HAVE_TMCDRIVER
+
+//	#define X_IS_TMC
+	#define X_MAX_CURRENT 1000  //in mA
+	#define X_SENSE_RESISTOR 91 //in mOhms
+	#define X_MICROSTEPS 16     //number of microsteps
+	
+//	#define X2_IS_TMC
+	#define X2_MAX_CURRENT 1000  //in mA
+	#define X2_SENSE_RESISTOR 91 //in mOhms
+	#define X2_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y_IS_TMC
+	#define Y_MAX_CURRENT 1000  //in mA
+	#define Y_SENSE_RESISTOR 91 //in mOhms
+	#define Y_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y2_IS_TMC
+	#define Y2_MAX_CURRENT 1000  //in mA
+	#define Y2_SENSE_RESISTOR 91 //in mOhms
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define Z_IS_TMC
+	#define Z_MAX_CURRENT 1000  //in mA
+	#define Z_SENSE_RESISTOR 91 //in mOhms
+	#define Z_MICROSTEPS 16     //number of microsteps
+	
+//	#define Z2_IS_TMC
+	#define Z2_MAX_CURRENT 1000  //in mA
+	#define Z2_SENSE_RESISTOR 91 //in mOhms
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	
+//	#define E0_IS_TMC
+	#define E0_MAX_CURRENT 1000  //in mA
+	#define E0_SENSE_RESISTOR 91 //in mOhms
+	#define E0_MICROSTEPS 16     //number of microsteps
+	
+//	#define E1_IS_TMC
+	#define E1_MAX_CURRENT 1000  //in mA
+	#define E1_SENSE_RESISTOR 91 //in mOhms
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E2_IS_TMC
+	#define E2_MAX_CURRENT 1000  //in mA
+	#define E2_SENSE_RESISTOR 91 //in mOhms
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E3_IS_TMC
+	#define E3_MAX_CURRENT 1000  //in mA
+	#define E3_SENSE_RESISTOR 91 //in mOhms
+	#define E3_MICROSTEPS 16     //number of microsteps		
+
+#endif
+
+/******************************************************************************\
+ * enable this section if you have L6470  motor drivers. 
+ * you need to import the L6470 library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_L6470DRIVER
+#ifdef HAVE_L6470DRIVER
+
+//	#define X_IS_L6470
+	#define X_MICROSTEPS 16     //number of microsteps
+	#define X_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define X2_IS_L6470
+	#define X2_MICROSTEPS 16     //number of microsteps
+	#define X2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y_IS_L6470
+	#define Y_MICROSTEPS 16     //number of microsteps
+	#define Y_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y2_IS_L6470
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	#define Y2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall	
+	
+//	#define Z_IS_L6470
+	#define Z_MICROSTEPS 16     //number of microsteps
+	#define Z_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Z2_IS_L6470
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	#define Z2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E0_IS_L6470
+	#define E0_MICROSTEPS 16     //number of microsteps
+	#define E0_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E0_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E1_IS_L6470
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	#define E1_MICROSTEPS 16     //number of microsteps
+	#define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E2_IS_L6470
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	#define E2_MICROSTEPS 16     //number of microsteps
+	#define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E3_IS_L6470
+	#define E3_MICROSTEPS 16     //number of microsteps		
+	#define E3_MICROSTEPS 16     //number of microsteps
+	#define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+#endif
+
 #include "Conditionals.h"
 #include "SanityCheck.h"
 

Marlin/example_configurations/Felix/Configuration.h

@@ -264,24 +264,27 @@ your extruder heater takes 2 minutes to hit the target on heating.
 // uncomment the 2 defines below:
 
 // Parameters for all extruder heaters
-//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 60 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds
-//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 5 // in degree Celsius
+//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
 
 // If you want to enable this feature for your bed heater,
 // uncomment the 2 defines below:
 
 // Parameters for the bed heater
-//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 30 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
-//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 5// in degree Celsius
+//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
 
 
 //===========================================================================
 //============================= Mechanical Settings =========================
 //===========================================================================
 
-// Uncomment the following line to enable CoreXY kinematics
+// Uncomment this option to enable CoreXY kinematics
 // #define COREXY
 
+// Enable this option for Toshiba steppers
+// #define CONFIG_STEPPERS_TOSHIBA
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -295,7 +298,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
   // #define ENDSTOPPULLUP_ZMIN
 #endif
 
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
@@ -318,13 +321,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DISABLE_E false // For all extruders
 #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
-#define INVERT_X_DIR true     // for Mendel set to false, for Orca set to true
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_Y_DIR true    // for Mendel set to true, for Orca set to false
+#define INVERT_X_DIR true
-#define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR true
-#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_Z_DIR true
-#define INVERT_E1_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E0_DIR false
-#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false
-#define INVERT_E3_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false
+#define INVERT_E3_DIR false
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -336,12 +340,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
 // Travel limits after homing (units are in mm)
-#define X_MAX_POS 255
 #define X_MIN_POS 0
-#define Y_MAX_POS 205
 #define Y_MIN_POS 0
-#define Z_MAX_POS 235
 #define Z_MIN_POS 0
+#define X_MAX_POS 255
+#define Y_MAX_POS 205
+#define Z_MAX_POS 235
 
 //===========================================================================
 //============================= Filament Runout Sensor ======================
@@ -379,39 +383,38 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 #ifdef ENABLE_AUTO_BED_LEVELING
 
-// There are 2 different ways to pick the X and Y locations to probe:
+  // There are 2 different ways to specify probing locations
-
+  //
   // - "grid" mode
-//    Probe every point in a rectangular grid
+  //   Probe several points in a rectangular grid.
-//    You must specify the rectangle, and the density of sample points
+  //   You specify the rectangle and the density of sample points.
   //   This mode is preferred because there are more measurements.
-//    It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
+  //
-
   // - "3-point" mode
   //   Probe 3 arbitrary points on the bed (that aren't colinear)
-//    You must specify the X & Y coordinates of all 3 points
+  //   You specify the XY coordinates of all 3 points.
 
+  // Enable this to sample the bed in a grid (least squares solution)
+  // Note: this feature generates 10KB extra code size
   #define AUTO_BED_LEVELING_GRID
-  // with AUTO_BED_LEVELING_GRID, the bed is sampled in a
+
-  // AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
-  // and least squares solution is calculated
-  // Note: this feature occupies 10'206 byte
   #ifdef AUTO_BED_LEVELING_GRID
 
     #define LEFT_PROBE_BED_POSITION 15
     #define RIGHT_PROBE_BED_POSITION 170
-    #define BACK_PROBE_BED_POSITION 180
     #define FRONT_PROBE_BED_POSITION 20
+    #define BACK_PROBE_BED_POSITION 180
 
-     // set the number of grid points per dimension
+    #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
-     // I wouldn't see a reason to go above 3 (=9 probing points on the bed)
+
+    // Set the number of grid points per dimension
+    // You probably don't need more than 3 (squared=9)
     #define AUTO_BED_LEVELING_GRID_POINTS 2
 
+  #else  // !AUTO_BED_LEVELING_GRID
 
-  #else  // not AUTO_BED_LEVELING_GRID
+      // Arbitrary points to probe. A simple cross-product
-    // with no grid, just probe 3 arbitrary points.  A simple cross-product
+      // is used to estimate the plane of the bed.
-    // is used to esimate the plane of the print bed
-
       #define ABL_PROBE_PT_1_X 15
       #define ABL_PROBE_PT_1_Y 180
       #define ABL_PROBE_PT_2_X 15
@@ -421,12 +424,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #endif // AUTO_BED_LEVELING_GRID
 
-
+  // Offsets to the probe relative to the extruder tip (Hotend - Probe)
-  // these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
-  #define X_PROBE_OFFSET_FROM_EXTRUDER -25
+  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // Probe on: -left  +right
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Probe on: -front +behind
-  #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
+  #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // -below (always!)
 
   #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
                                         // Be sure you have this distance over your Z_MAX_POS in case
@@ -435,6 +437,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #define Z_RAISE_BEFORE_PROBING 15   //How much the extruder will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
+  #define Z_RAISE_AFTER_PROBING 15    //How much the extruder will be raised after the last probing point.
+
+//   #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
+                                                                            //Useful to retract a deployable probe.
                                                                            
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@@ -472,10 +478,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 // Manual homing switch locations:
 // For deltabots this means top and center of the Cartesian print volume.
+#ifdef MANUAL_HOME_POSITIONS
   #define MANUAL_X_HOME_POS 0
   #define MANUAL_Y_HOME_POS 0
   #define MANUAL_Z_HOME_POS 0
   //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
+#endif
 
 //// MOVEMENT SETTINGS
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
@@ -513,8 +521,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #ifdef CUSTOM_M_CODES
   #ifdef ENABLE_AUTO_BED_LEVELING
     #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-    #define Z_PROBE_OFFSET_RANGE_MIN -15
+    #define Z_PROBE_OFFSET_RANGE_MIN -20
-    #define Z_PROBE_OFFSET_RANGE_MAX -5
+    #define Z_PROBE_OFFSET_RANGE_MAX 20
   #endif
 #endif
 
@@ -542,13 +550,16 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //==============================LCD and SD support=============================
 
 // Define your display language below. Replace (en) with your language code and uncomment.
-// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
+// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
 // See also language.h
 //#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Character based displays can have different extended charsets.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
-//#define DISPLAY_CHARSET_HD44780_JAPAN     // "ääööüüß23°"
+// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
-//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
+// See also documentation/LCDLanguageFont.md
+  #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
+  //#define DISPLAY_CHARSET_HD44780_WESTERN
+  //#define DISPLAY_CHARSET_HD44780_CYRILLIC
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
@@ -561,6 +572,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+                                               // 0 to disable buzzer feedback  
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -622,11 +634,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 // Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
 #define FAST_PWM_FAN
 
-// Temperature status LEDs that display the hotend and bet temperature.
-// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
-// Otherwise the RED led is on. There is 1C hysteresis.
-//#define TEMP_STAT_LEDS
-
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
@@ -638,6 +645,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 // at zero value, there are 128 effective control positions.
 #define SOFT_PWM_SCALE 0
 
+// Temperature status LEDs that display the hotend and bet temperature.
+// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
+// Otherwise the RED led is on. There is 1C hysteresis.
+//#define TEMP_STAT_LEDS
+
 // M240  Triggers a camera by emulating a Canon RC-1 Remote
 // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
 // #define PHOTOGRAPH_PIN     23

Marlin/example_configurations/Felix/Configuration_DUAL.h

@@ -264,24 +264,27 @@ your extruder heater takes 2 minutes to hit the target on heating.
 // uncomment the 2 defines below:
 
 // Parameters for all extruder heaters
-//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 60 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds
-//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 5 // in degree Celsius
+//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
 
 // If you want to enable this feature for your bed heater,
 // uncomment the 2 defines below:
 
 // Parameters for the bed heater
-//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 30 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
-//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 5// in degree Celsius
+//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
 
 
 //===========================================================================
 //============================= Mechanical Settings =========================
 //===========================================================================
 
-// Uncomment the following line to enable CoreXY kinematics
+// Uncomment this option to enable CoreXY kinematics
 // #define COREXY
 
+// Enable this option for Toshiba steppers
+// #define CONFIG_STEPPERS_TOSHIBA
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -295,7 +298,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
   // #define ENDSTOPPULLUP_ZMIN
 #endif
 
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
@@ -318,13 +321,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DISABLE_E false // For all extruders
 #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
-#define INVERT_X_DIR true     // for Mendel set to false, for Orca set to true
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_Y_DIR true     // for Mendel set to true, for Orca set to false
+#define INVERT_X_DIR true
-#define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR true
-#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_Z_DIR true
-#define INVERT_E1_DIR true    // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E0_DIR false
-#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR true
-#define INVERT_E3_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false
+#define INVERT_E3_DIR false
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -336,12 +340,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
 // Travel limits after homing (units are in mm)
-#define X_MAX_POS 255
 #define X_MIN_POS 0
-#define Y_MAX_POS 205
 #define Y_MIN_POS 0
-#define Z_MAX_POS 235
 #define Z_MIN_POS 0
+#define X_MAX_POS 255
+#define Y_MAX_POS 205
+#define Z_MAX_POS 235
 
 //===========================================================================
 //============================= Filament Runout Sensor ======================
@@ -379,39 +383,38 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 #ifdef ENABLE_AUTO_BED_LEVELING
 
-// There are 2 different ways to pick the X and Y locations to probe:
+  // There are 2 different ways to specify probing locations
-
+  //
   // - "grid" mode
-//    Probe every point in a rectangular grid
+  //   Probe several points in a rectangular grid.
-//    You must specify the rectangle, and the density of sample points
+  //   You specify the rectangle and the density of sample points.
   //   This mode is preferred because there are more measurements.
-//    It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
+  //
-
   // - "3-point" mode
   //   Probe 3 arbitrary points on the bed (that aren't colinear)
-//    You must specify the X & Y coordinates of all 3 points
+  //   You specify the XY coordinates of all 3 points.
 
+  // Enable this to sample the bed in a grid (least squares solution)
+  // Note: this feature generates 10KB extra code size
   #define AUTO_BED_LEVELING_GRID
-  // with AUTO_BED_LEVELING_GRID, the bed is sampled in a
+
-  // AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
-  // and least squares solution is calculated
-  // Note: this feature occupies 10'206 byte
   #ifdef AUTO_BED_LEVELING_GRID
 
     #define LEFT_PROBE_BED_POSITION 15
     #define RIGHT_PROBE_BED_POSITION 170
-    #define BACK_PROBE_BED_POSITION 180
     #define FRONT_PROBE_BED_POSITION 20
+    #define BACK_PROBE_BED_POSITION 180
 
-     // set the number of grid points per dimension
+    #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this      
-     // I wouldn't see a reason to go above 3 (=9 probing points on the bed)
+
+    // Set the number of grid points per dimension
+    // You probably don't need more than 3 (squared=9)
     #define AUTO_BED_LEVELING_GRID_POINTS 2
 
+  #else  // !AUTO_BED_LEVELING_GRID
 
-  #else  // not AUTO_BED_LEVELING_GRID
+      // Arbitrary points to probe. A simple cross-product
-    // with no grid, just probe 3 arbitrary points.  A simple cross-product
+      // is used to estimate the plane of the bed.
-    // is used to esimate the plane of the print bed
-
       #define ABL_PROBE_PT_1_X 15
       #define ABL_PROBE_PT_1_Y 180
       #define ABL_PROBE_PT_2_X 15
@@ -421,12 +424,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #endif // AUTO_BED_LEVELING_GRID
 
-
+  // Offsets to the probe relative to the extruder tip (Hotend - Probe)
-  // these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
-  #define X_PROBE_OFFSET_FROM_EXTRUDER -25
+  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // Probe on: -left  +right
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Probe on: -front +behind
-  #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
+  #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // -below (always!)
 
   #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
                                         // Be sure you have this distance over your Z_MAX_POS in case
@@ -435,6 +437,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #define Z_RAISE_BEFORE_PROBING 15   //How much the extruder will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
+  #define Z_RAISE_AFTER_PROBING 15    //How much the extruder will be raised after the last probing point.
+
+//   #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
+                                                                            //Useful to retract a deployable probe.
                                                                            
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
@@ -472,10 +478,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 // Manual homing switch locations:
 // For deltabots this means top and center of the Cartesian print volume.
+#ifdef MANUAL_HOME_POSITIONS
   #define MANUAL_X_HOME_POS 0
   #define MANUAL_Y_HOME_POS 0
   #define MANUAL_Z_HOME_POS 0
   //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
+#endif
 
 //// MOVEMENT SETTINGS
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
@@ -513,8 +521,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #ifdef CUSTOM_M_CODES
   #ifdef ENABLE_AUTO_BED_LEVELING
     #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-    #define Z_PROBE_OFFSET_RANGE_MIN -15
+    #define Z_PROBE_OFFSET_RANGE_MIN -20
-    #define Z_PROBE_OFFSET_RANGE_MAX -5
+    #define Z_PROBE_OFFSET_RANGE_MAX 20
   #endif
 #endif
 
@@ -542,13 +550,16 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //==============================LCD and SD support=============================
 
 // Define your display language below. Replace (en) with your language code and uncomment.
-// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
+// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
 // See also language.h
 //#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Character based displays can have different extended charsets.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
-//#define DISPLAY_CHARSET_HD44780_JAPAN     // "ääööüüß23°"
+// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
-//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
+// See also documentation/LCDLanguageFont.md
+  #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
+  //#define DISPLAY_CHARSET_HD44780_WESTERN
+  //#define DISPLAY_CHARSET_HD44780_CYRILLIC
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
@@ -561,6 +572,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+                                               // 0 to disable buzzer feedback  
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -619,15 +631,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 //#define SAV_3DLCD
 
-
 // Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
 #define FAST_PWM_FAN
 
-// Temperature status LEDs that display the hotend and bet temperature.
-// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
-// Otherwise the RED led is on. There is 1C hysteresis.
-//#define TEMP_STAT_LEDS
-
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
@@ -639,6 +645,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 // at zero value, there are 128 effective control positions.
 #define SOFT_PWM_SCALE 0
 
+// Temperature status LEDs that display the hotend and bet temperature.
+// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
+// Otherwise the RED led is on. There is 1C hysteresis.
+//#define TEMP_STAT_LEDS
+
 // M240  Triggers a camera by emulating a Canon RC-1 Remote
 // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
 // #define PHOTOGRAPH_PIN     23

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -100,6 +100,30 @@
 // On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
 //#define Z_DUAL_STEPPER_DRIVERS
 
+#ifdef Z_DUAL_STEPPER_DRIVERS
+
+  // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+  // That way the machine is capable to align the bed during home, since both Z steppers are homed. 
+  // There is also an implementation of M666 (software endstops adjustment) to this feature.
+  // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+  // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+  // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+  // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+  // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+  #define Z_DUAL_ENDSTOPS
+
+  #ifdef Z_DUAL_ENDSTOPS
+    #define Z2_STEP_PIN E2_STEP_PIN           // Stepper to be used to Z2 axis.
+    #define Z2_DIR_PIN E2_DIR_PIN
+    #define Z2_ENABLE_PIN E2_ENABLE_PIN
+    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
+    const bool Z2_MAX_ENDSTOP_INVERTING = false;
+    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+  #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
 // Same again but for Y Axis.
 //#define Y_DUAL_STEPPER_DRIVERS
 
@@ -210,13 +234,21 @@
 //===========================================================================
 
 #define ENCODER_RATE_MULTIPLIER         // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
-#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value
+#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
-#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
 //#define ENCODER_RATE_MULTIPLIER_DEBUG  // If defined, output the encoder steps per second value
 
 //#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
 
+#ifdef SDSUPPORT
+
+  // If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+  // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+  // in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+  // be commented out otherwise
+  #define SDCARDDETECTINVERTED
+
   #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
@@ -239,6 +271,8 @@
     //#define PROGRESS_MSG_ONCE
   #endif
 
+#endif // SDSUPPORT
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -275,7 +309,7 @@
   #define EXTRUDER_ADVANCE_K .0
   #define D_FILAMENT 2.85
   #define STEPS_MM_E 836
-#endif // ADVANCE
+#endif
 
 // Arc interpretation settings:
 #define MM_PER_ARC_SEGMENT 1
@@ -283,32 +317,6 @@
 
 const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
-// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
-// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
-// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
-// be commented out otherwise
-#define SDCARDDETECTINVERTED
-
-//#ifdef ULTIPANEL
-// #undef SDCARDDETECTINVERTED
-//#endif
-
-// Power Signal Control Definitions
-// By default use ATX definition
-#ifndef POWER_SUPPLY
-  #define POWER_SUPPLY 1
-#endif
-// 1 = ATX
-#if (POWER_SUPPLY == 1)
-  #define PS_ON_AWAKE  LOW
-  #define PS_ON_ASLEEP HIGH
-#endif
-// 2 = X-Box 360 203W
-#if (POWER_SUPPLY == 2)
-  #define PS_ON_AWAKE  HIGH
-  #define PS_ON_ASLEEP LOW
-#endif
-
 // Control heater 0 and heater 1 in parallel.
 //#define HEATERS_PARALLEL
 
@@ -318,7 +326,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 
 // The number of linear motions that can be in the plan at any give time.
 // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
-#if defined SDSUPPORT
+#ifdef SDSUPPORT
   #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
   #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
@@ -360,6 +368,139 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #endif
 #endif
 
+/******************************************************************************\
+ * enable this section if you have TMC26X motor drivers. 
+ * you need to import the TMC26XStepper library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_TMCDRIVER
+#ifdef HAVE_TMCDRIVER
+
+//	#define X_IS_TMC
+	#define X_MAX_CURRENT 1000  //in mA
+	#define X_SENSE_RESISTOR 91 //in mOhms
+	#define X_MICROSTEPS 16     //number of microsteps
+	
+//	#define X2_IS_TMC
+	#define X2_MAX_CURRENT 1000  //in mA
+	#define X2_SENSE_RESISTOR 91 //in mOhms
+	#define X2_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y_IS_TMC
+	#define Y_MAX_CURRENT 1000  //in mA
+	#define Y_SENSE_RESISTOR 91 //in mOhms
+	#define Y_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y2_IS_TMC
+	#define Y2_MAX_CURRENT 1000  //in mA
+	#define Y2_SENSE_RESISTOR 91 //in mOhms
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define Z_IS_TMC
+	#define Z_MAX_CURRENT 1000  //in mA
+	#define Z_SENSE_RESISTOR 91 //in mOhms
+	#define Z_MICROSTEPS 16     //number of microsteps
+	
+//	#define Z2_IS_TMC
+	#define Z2_MAX_CURRENT 1000  //in mA
+	#define Z2_SENSE_RESISTOR 91 //in mOhms
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	
+//	#define E0_IS_TMC
+	#define E0_MAX_CURRENT 1000  //in mA
+	#define E0_SENSE_RESISTOR 91 //in mOhms
+	#define E0_MICROSTEPS 16     //number of microsteps
+	
+//	#define E1_IS_TMC
+	#define E1_MAX_CURRENT 1000  //in mA
+	#define E1_SENSE_RESISTOR 91 //in mOhms
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E2_IS_TMC
+	#define E2_MAX_CURRENT 1000  //in mA
+	#define E2_SENSE_RESISTOR 91 //in mOhms
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E3_IS_TMC
+	#define E3_MAX_CURRENT 1000  //in mA
+	#define E3_SENSE_RESISTOR 91 //in mOhms
+	#define E3_MICROSTEPS 16     //number of microsteps		
+
+#endif
+
+/******************************************************************************\
+ * enable this section if you have L6470  motor drivers. 
+ * you need to import the L6470 library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_L6470DRIVER
+#ifdef HAVE_L6470DRIVER
+
+//	#define X_IS_L6470
+	#define X_MICROSTEPS 16     //number of microsteps
+	#define X_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define X2_IS_L6470
+	#define X2_MICROSTEPS 16     //number of microsteps
+	#define X2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y_IS_L6470
+	#define Y_MICROSTEPS 16     //number of microsteps
+	#define Y_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y2_IS_L6470
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	#define Y2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall	
+	
+//	#define Z_IS_L6470
+	#define Z_MICROSTEPS 16     //number of microsteps
+	#define Z_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Z2_IS_L6470
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	#define Z2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E0_IS_L6470
+	#define E0_MICROSTEPS 16     //number of microsteps
+	#define E0_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E0_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E1_IS_L6470
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	#define E1_MICROSTEPS 16     //number of microsteps
+	#define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E2_IS_L6470
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	#define E2_MICROSTEPS 16     //number of microsteps
+	#define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E3_IS_L6470
+	#define E3_MICROSTEPS 16     //number of microsteps		
+	#define E3_MICROSTEPS 16     //number of microsteps
+	#define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+#endif
+
 #include "Conditionals.h"
 #include "SanityCheck.h"
 

Marlin/example_configurations/Hephestos/Configuration.h

@@ -321,7 +321,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
   // #define ENDSTOPPULLUP_ZMIN
 #endif
 
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
@@ -344,13 +344,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DISABLE_E false // For all extruders
 #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
-#define INVERT_X_DIR true    // for Mendel set to false, for Orca set to true
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
+#define INVERT_X_DIR true
-#define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR false
-#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_Z_DIR true
-#define INVERT_E1_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E0_DIR false
-#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false
-#define INVERT_E3_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false
+#define INVERT_E3_DIR false
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -361,13 +362,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
-// Travel limits after homing (units in mm)
+// Travel limits after homing (units are in mm)
-#define X_MAX_POS 215
 #define X_MIN_POS 0
-#define Y_MAX_POS 210
 #define Y_MIN_POS 0
-#define Z_MAX_POS 180
 #define Z_MIN_POS 0
+#define X_MAX_POS 215
+#define Y_MAX_POS 210
+#define Z_MAX_POS 180
 
 //===========================================================================
 //============================= Filament Runout Sensor ======================
@@ -433,7 +434,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
     // You probably don't need more than 3 (squared=9)
     #define AUTO_BED_LEVELING_GRID_POINTS 2
 
-
   #else  // !AUTO_BED_LEVELING_GRID
 
       // Arbitrary points to probe. A simple cross-product
@@ -447,11 +447,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #endif // AUTO_BED_LEVELING_GRID
 
-
   // Offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
-  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // -left  +right
+  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // Probe on: -left  +right
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // -front +behind
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Probe on: -front +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // -below (always!)
 
   #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
@@ -463,6 +462,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
   #define Z_RAISE_AFTER_PROBING 15    //How much the extruder will be raised after the last probing point.
 
+//   #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
+                                                                            //Useful to retract a deployable probe.
+                                                                           
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
@@ -499,10 +501,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 // Manual homing switch locations:
 // For deltabots this means top and center of the Cartesian print volume.
+#ifdef MANUAL_HOME_POSITIONS
   #define MANUAL_X_HOME_POS 0
   #define MANUAL_Y_HOME_POS 0
   #define MANUAL_Z_HOME_POS 0
   //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
+#endif
 
 //// MOVEMENT SETTINGS
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
@@ -518,8 +522,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DEFAULT_RETRACT_ACCELERATION  1000   // E acceleration in mm/s^2 for retracts
 #define DEFAULT_TRAVEL_ACCELERATION   1000    // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
 
-
-
 // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
 // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
 // For the other hotends it is their distance from the extruder 0 hotend.
@@ -541,8 +543,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #ifdef CUSTOM_M_CODES
   #ifdef ENABLE_AUTO_BED_LEVELING
     #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-    #define Z_PROBE_OFFSET_RANGE_MIN -15
+    #define Z_PROBE_OFFSET_RANGE_MIN -20
-    #define Z_PROBE_OFFSET_RANGE_MAX -5
+    #define Z_PROBE_OFFSET_RANGE_MAX 20
   #endif
 #endif
 
@@ -570,13 +572,16 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //==============================LCD and SD support=============================
 
 // Define your display language below. Replace (en) with your language code and uncomment.
-// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
+// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
 // See also language.h
 //#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Character based displays can have different extended charsets.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
-#define DISPLAY_CHARSET_HD44780_JAPAN     // "ääööüüß23°"
+// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
-//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
+// See also documentation/LCDLanguageFont.md
+  #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
+  //#define DISPLAY_CHARSET_HD44780_WESTERN
+  //#define DISPLAY_CHARSET_HD44780_CYRILLIC
 
 #define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
@@ -589,6 +594,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+                                               // 0 to disable buzzer feedback  
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -651,7 +657,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define FAST_PWM_FAN
 
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
-// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
 //#define FAN_SOFT_PWM
 

Marlin/example_configurations/Hephestos/Configuration_adv.h

@@ -100,6 +100,30 @@
 // On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
 //#define Z_DUAL_STEPPER_DRIVERS
 
+#ifdef Z_DUAL_STEPPER_DRIVERS
+
+  // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+  // That way the machine is capable to align the bed during home, since both Z steppers are homed. 
+  // There is also an implementation of M666 (software endstops adjustment) to this feature.
+  // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+  // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+  // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+  // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+  // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+  #define Z_DUAL_ENDSTOPS
+
+  #ifdef Z_DUAL_ENDSTOPS
+    #define Z2_STEP_PIN E2_STEP_PIN           // Stepper to be used to Z2 axis.
+    #define Z2_DIR_PIN E2_DIR_PIN
+    #define Z2_ENABLE_PIN E2_ENABLE_PIN
+    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
+    const bool Z2_MAX_ENDSTOP_INVERTING = false;
+    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+  #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
 // Same again but for Y Axis.
 //#define Y_DUAL_STEPPER_DRIVERS
 
@@ -158,11 +182,7 @@
 //#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}
-#ifdef CONFIG_STEPPERS_TOSHIBA
+
-#define MAX_STEP_FREQUENCY 10000 // Max step frequency for Toshiba Stepper Controllers
-#else
-#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
-#endif
 //By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
 #define INVERT_X_STEP_PIN false
 #define INVERT_Y_STEP_PIN false
@@ -214,20 +234,28 @@
 //===========================================================================
 
 #define ENCODER_RATE_MULTIPLIER         // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
-#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value
+#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
-#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
 //#define ENCODER_RATE_MULTIPLIER_DEBUG  // If defined, output the encoder steps per second value
 
 //#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
 
+#ifdef SDSUPPORT
+
+  // If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+  // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+  // in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+  // be commented out otherwise
+  #define SDCARDDETECTINVERTED
+
   #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
   #define SDCARD_RATHERRECENTFIRST  //reverse file order of sd card menu display. Its sorted practically after the file system block order.
   // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
   // using:
-#define MENU_ADDAUTOSTART
+  //#define MENU_ADDAUTOSTART
 
   // Show a progress bar on HD44780 LCDs for SD printing
   //#define LCD_PROGRESS_BAR
@@ -243,6 +271,8 @@
     //#define PROGRESS_MSG_ONCE
   #endif
 
+#endif // SDSUPPORT
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -279,7 +309,7 @@
   #define EXTRUDER_ADVANCE_K .0
   #define D_FILAMENT 1.75
   #define STEPS_MM_E 100.47095761381482
-#endif // ADVANCE
+#endif
 
 // Arc interpretation settings:
 #define MM_PER_ARC_SEGMENT 1
@@ -287,12 +317,6 @@
 
 const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
-// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
-// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
-// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
-// be commented out otherwise
-#define SDCARDDETECTINVERTED
-
 // Control heater 0 and heater 1 in parallel.
 //#define HEATERS_PARALLEL
 
@@ -302,7 +326,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 
 // The number of linear motions that can be in the plan at any give time.
 // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
-#if defined SDSUPPORT
+#ifdef SDSUPPORT
   #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
   #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
@@ -344,6 +368,139 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #endif
 #endif
 
+/******************************************************************************\
+ * enable this section if you have TMC26X motor drivers. 
+ * you need to import the TMC26XStepper library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_TMCDRIVER
+#ifdef HAVE_TMCDRIVER
+
+//	#define X_IS_TMC
+	#define X_MAX_CURRENT 1000  //in mA
+	#define X_SENSE_RESISTOR 91 //in mOhms
+	#define X_MICROSTEPS 16     //number of microsteps
+	
+//	#define X2_IS_TMC
+	#define X2_MAX_CURRENT 1000  //in mA
+	#define X2_SENSE_RESISTOR 91 //in mOhms
+	#define X2_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y_IS_TMC
+	#define Y_MAX_CURRENT 1000  //in mA
+	#define Y_SENSE_RESISTOR 91 //in mOhms
+	#define Y_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y2_IS_TMC
+	#define Y2_MAX_CURRENT 1000  //in mA
+	#define Y2_SENSE_RESISTOR 91 //in mOhms
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define Z_IS_TMC
+	#define Z_MAX_CURRENT 1000  //in mA
+	#define Z_SENSE_RESISTOR 91 //in mOhms
+	#define Z_MICROSTEPS 16     //number of microsteps
+	
+//	#define Z2_IS_TMC
+	#define Z2_MAX_CURRENT 1000  //in mA
+	#define Z2_SENSE_RESISTOR 91 //in mOhms
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	
+//	#define E0_IS_TMC
+	#define E0_MAX_CURRENT 1000  //in mA
+	#define E0_SENSE_RESISTOR 91 //in mOhms
+	#define E0_MICROSTEPS 16     //number of microsteps
+	
+//	#define E1_IS_TMC
+	#define E1_MAX_CURRENT 1000  //in mA
+	#define E1_SENSE_RESISTOR 91 //in mOhms
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E2_IS_TMC
+	#define E2_MAX_CURRENT 1000  //in mA
+	#define E2_SENSE_RESISTOR 91 //in mOhms
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E3_IS_TMC
+	#define E3_MAX_CURRENT 1000  //in mA
+	#define E3_SENSE_RESISTOR 91 //in mOhms
+	#define E3_MICROSTEPS 16     //number of microsteps		
+
+#endif
+
+/******************************************************************************\
+ * enable this section if you have L6470  motor drivers. 
+ * you need to import the L6470 library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_L6470DRIVER
+#ifdef HAVE_L6470DRIVER
+
+//	#define X_IS_L6470
+	#define X_MICROSTEPS 16     //number of microsteps
+	#define X_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define X2_IS_L6470
+	#define X2_MICROSTEPS 16     //number of microsteps
+	#define X2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y_IS_L6470
+	#define Y_MICROSTEPS 16     //number of microsteps
+	#define Y_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y2_IS_L6470
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	#define Y2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall	
+	
+//	#define Z_IS_L6470
+	#define Z_MICROSTEPS 16     //number of microsteps
+	#define Z_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Z2_IS_L6470
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	#define Z2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E0_IS_L6470
+	#define E0_MICROSTEPS 16     //number of microsteps
+	#define E0_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E0_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E1_IS_L6470
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	#define E1_MICROSTEPS 16     //number of microsteps
+	#define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E2_IS_L6470
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	#define E2_MICROSTEPS 16     //number of microsteps
+	#define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E3_IS_L6470
+	#define E3_MICROSTEPS 16     //number of microsteps		
+	#define E3_MICROSTEPS 16     //number of microsteps
+	#define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+#endif
+
 #include "Conditionals.h"
 #include "SanityCheck.h"
 

Marlin/example_configurations/K8200/Configuration.h

@@ -326,7 +326,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
   #define ENDSTOPPULLUP_ZMIN
 #endif
 
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
@@ -349,13 +349,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DISABLE_E false // For all extruders
 #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
-#define INVERT_X_DIR false    // for Mendel set to false, for Orca set to true
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
+#define INVERT_X_DIR false
-#define INVERT_Z_DIR false    // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR false
-#define INVERT_E0_DIR true   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_Z_DIR false
-#define INVERT_E1_DIR true   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E0_DIR true
-#define INVERT_E2_DIR true   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR true
-#define INVERT_E3_DIR true   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR true
+#define INVERT_E3_DIR true
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -367,12 +368,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
 // Travel limits after homing (units are in mm)
-#define X_MAX_POS 200
 #define X_MIN_POS 0
-#define Y_MAX_POS 200
 #define Y_MIN_POS 0
-#define Z_MAX_POS 200
 #define Z_MIN_POS 0
+#define X_MAX_POS 200
+#define Y_MAX_POS 200
+#define Z_MAX_POS 200
 
 //===========================================================================
 //============================= Filament Runout Sensor ======================
@@ -438,7 +439,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
     // You probably don't need more than 3 (squared=9)
     #define AUTO_BED_LEVELING_GRID_POINTS 2
 
-
   #else  // !AUTO_BED_LEVELING_GRID
 
       // Arbitrary points to probe. A simple cross-product
@@ -452,11 +452,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #endif // AUTO_BED_LEVELING_GRID
 
-
   // Offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
-  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // -left  +right
+  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // Probe on: -left  +right
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // -front +behind
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Probe on: -front +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // -below (always!)
 
   #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
@@ -468,6 +467,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
   #define Z_RAISE_AFTER_PROBING 15    //How much the extruder will be raised after the last probing point.
 
+//   #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
+                                                                            //Useful to retract a deployable probe.
+                                                                           
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
@@ -504,10 +506,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 // Manual homing switch locations:
 // For deltabots this means top and center of the Cartesian print volume.
+#ifdef MANUAL_HOME_POSITIONS
   #define MANUAL_X_HOME_POS 0
   #define MANUAL_Y_HOME_POS 0
   #define MANUAL_Z_HOME_POS 0
   //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
+#endif
 
 //// MOVEMENT SETTINGS
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
@@ -545,8 +549,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #ifdef CUSTOM_M_CODES
   #ifdef ENABLE_AUTO_BED_LEVELING
     #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-    #define Z_PROBE_OFFSET_RANGE_MIN -15
+    #define Z_PROBE_OFFSET_RANGE_MIN -20
-    #define Z_PROBE_OFFSET_RANGE_MAX -5
+    #define Z_PROBE_OFFSET_RANGE_MAX 20
   #endif
 #endif
 
@@ -574,13 +578,16 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //==============================LCD and SD support=============================
 
 // Define your display language below. Replace (en) with your language code and uncomment.
-// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
+// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
 // See also language.h
 //#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Character based displays can have different extended charsets.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
-#define DISPLAY_CHARSET_HD44780_JAPAN     // "ääööüüß23°"
+// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
-//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
+// See also documentation/LCDLanguageFont.md
+  #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
+  //#define DISPLAY_CHARSET_HD44780_WESTERN
+  //#define DISPLAY_CHARSET_HD44780_CYRILLIC
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
@@ -593,6 +600,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+                                               // 0 to disable buzzer feedback  
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -655,7 +663,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define FAST_PWM_FAN
 
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
-// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
 //#define FAN_SOFT_PWM
 

Marlin/example_configurations/K8200/Configuration_adv.h

@@ -100,6 +100,30 @@
 // On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
 //#define Z_DUAL_STEPPER_DRIVERS
 
+#ifdef Z_DUAL_STEPPER_DRIVERS
+
+  // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+  // That way the machine is capable to align the bed during home, since both Z steppers are homed. 
+  // There is also an implementation of M666 (software endstops adjustment) to this feature.
+  // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+  // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+  // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+  // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+  // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+  #define Z_DUAL_ENDSTOPS
+
+  #ifdef Z_DUAL_ENDSTOPS
+    #define Z2_STEP_PIN E2_STEP_PIN           // Stepper to be used to Z2 axis.
+    #define Z2_DIR_PIN E2_DIR_PIN
+    #define Z2_ENABLE_PIN E2_ENABLE_PIN
+    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
+    const bool Z2_MAX_ENDSTOP_INVERTING = false;
+    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+  #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
 // Same again but for Y Axis.
 //#define Y_DUAL_STEPPER_DRIVERS
 
@@ -210,13 +234,21 @@
 //===========================================================================
 
 #define ENCODER_RATE_MULTIPLIER         // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
-#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value
+#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
-#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
 //#define ENCODER_RATE_MULTIPLIER_DEBUG  // If defined, output the encoder steps per second value
 
 //#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
 
+#ifdef SDSUPPORT
+
+  // If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+  // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+  // in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+  // be commented out otherwise
+  #define SDCARDDETECTINVERTED
+
   #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
@@ -239,6 +271,8 @@
     //#define PROGRESS_MSG_ONCE
   #endif
 
+#endif // SDSUPPORT
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -275,7 +309,7 @@
   #define EXTRUDER_ADVANCE_K .0
   #define D_FILAMENT 2.85
   #define STEPS_MM_E 836
-#endif // ADVANCE
+#endif
 
 // Arc interpretation settings:
 #define MM_PER_ARC_SEGMENT 1
@@ -283,12 +317,6 @@
 
 const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
-// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
-// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
-// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
-// be commented out otherwise
-#define SDCARDDETECTINVERTED
-
 // Control heater 0 and heater 1 in parallel.
 //#define HEATERS_PARALLEL
 
@@ -298,7 +326,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 
 // The number of linear motions that can be in the plan at any give time.
 // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
-#if defined SDSUPPORT
+#ifdef SDSUPPORT
   #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
   #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
@@ -340,6 +368,139 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #endif
 #endif
 
+/******************************************************************************\
+ * enable this section if you have TMC26X motor drivers. 
+ * you need to import the TMC26XStepper library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_TMCDRIVER
+#ifdef HAVE_TMCDRIVER
+
+//	#define X_IS_TMC
+	#define X_MAX_CURRENT 1000  //in mA
+	#define X_SENSE_RESISTOR 91 //in mOhms
+	#define X_MICROSTEPS 16     //number of microsteps
+	
+//	#define X2_IS_TMC
+	#define X2_MAX_CURRENT 1000  //in mA
+	#define X2_SENSE_RESISTOR 91 //in mOhms
+	#define X2_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y_IS_TMC
+	#define Y_MAX_CURRENT 1000  //in mA
+	#define Y_SENSE_RESISTOR 91 //in mOhms
+	#define Y_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y2_IS_TMC
+	#define Y2_MAX_CURRENT 1000  //in mA
+	#define Y2_SENSE_RESISTOR 91 //in mOhms
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define Z_IS_TMC
+	#define Z_MAX_CURRENT 1000  //in mA
+	#define Z_SENSE_RESISTOR 91 //in mOhms
+	#define Z_MICROSTEPS 16     //number of microsteps
+	
+//	#define Z2_IS_TMC
+	#define Z2_MAX_CURRENT 1000  //in mA
+	#define Z2_SENSE_RESISTOR 91 //in mOhms
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	
+//	#define E0_IS_TMC
+	#define E0_MAX_CURRENT 1000  //in mA
+	#define E0_SENSE_RESISTOR 91 //in mOhms
+	#define E0_MICROSTEPS 16     //number of microsteps
+	
+//	#define E1_IS_TMC
+	#define E1_MAX_CURRENT 1000  //in mA
+	#define E1_SENSE_RESISTOR 91 //in mOhms
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E2_IS_TMC
+	#define E2_MAX_CURRENT 1000  //in mA
+	#define E2_SENSE_RESISTOR 91 //in mOhms
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E3_IS_TMC
+	#define E3_MAX_CURRENT 1000  //in mA
+	#define E3_SENSE_RESISTOR 91 //in mOhms
+	#define E3_MICROSTEPS 16     //number of microsteps		
+
+#endif
+
+/******************************************************************************\
+ * enable this section if you have L6470  motor drivers. 
+ * you need to import the L6470 library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_L6470DRIVER
+#ifdef HAVE_L6470DRIVER
+
+//	#define X_IS_L6470
+	#define X_MICROSTEPS 16     //number of microsteps
+	#define X_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define X2_IS_L6470
+	#define X2_MICROSTEPS 16     //number of microsteps
+	#define X2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y_IS_L6470
+	#define Y_MICROSTEPS 16     //number of microsteps
+	#define Y_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y2_IS_L6470
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	#define Y2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall	
+	
+//	#define Z_IS_L6470
+	#define Z_MICROSTEPS 16     //number of microsteps
+	#define Z_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Z2_IS_L6470
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	#define Z2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E0_IS_L6470
+	#define E0_MICROSTEPS 16     //number of microsteps
+	#define E0_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E0_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E1_IS_L6470
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	#define E1_MICROSTEPS 16     //number of microsteps
+	#define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E2_IS_L6470
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	#define E2_MICROSTEPS 16     //number of microsteps
+	#define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E3_IS_L6470
+	#define E3_MICROSTEPS 16     //number of microsteps		
+	#define E3_MICROSTEPS 16     //number of microsteps
+	#define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+#endif
+
 #include "Conditionals.h"
 #include "SanityCheck.h"
 

Marlin/example_configurations/SCARA/Configuration.h

@@ -350,7 +350,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
   // #define ENDSTOPPULLUP_ZMIN
 #endif
 
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
@@ -373,13 +373,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DISABLE_E false // For all extruders
 #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
-#define INVERT_X_DIR false    // for Mendel set to false, for Orca set to true
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
+#define INVERT_X_DIR false
-#define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR false
-#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_Z_DIR true
-#define INVERT_E1_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E0_DIR false
-#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false
-#define INVERT_E3_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false
+#define INVERT_E3_DIR false
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -391,12 +392,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
 // Travel limits after homing (units are in mm)
-#define X_MAX_POS 200
 #define X_MIN_POS 0
-#define Y_MAX_POS 200
 #define Y_MIN_POS 0
-#define Z_MAX_POS 225
 #define Z_MIN_POS MANUAL_Z_HOME_POS
+#define X_MAX_POS 200
+#define Y_MAX_POS 200
+#define Z_MAX_POS 225
 
 //===========================================================================
 //============================= Filament Runout Sensor ======================
@@ -462,7 +463,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
     // You probably don't need more than 3 (squared=9)
     #define AUTO_BED_LEVELING_GRID_POINTS 2
 
-
   #else  // !AUTO_BED_LEVELING_GRID
 
       // Arbitrary points to probe. A simple cross-product
@@ -476,11 +476,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #endif // AUTO_BED_LEVELING_GRID
 
-
   // Offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
-  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // -left  +right
+  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // Probe on: -left  +right
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // -front +behind
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Probe on: -front +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // -below (always!)
 
   //#define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
@@ -492,6 +491,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
   #define Z_RAISE_AFTER_PROBING 15    //How much the extruder will be raised after the last probing point.
 
+//   #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
+                                                                            //Useful to retract a deployable probe.
+                                                                           
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
@@ -528,11 +530,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 // Manual homing switch locations:
 // For deltabots this means top and center of the Cartesian print volume.
+#ifdef MANUAL_HOME_POSITIONS
   // For SCARA: Offset between HomingPosition and Bed X=0 / Y=0
   #define MANUAL_X_HOME_POS -22.
   #define MANUAL_Y_HOME_POS -52.
   #define MANUAL_Z_HOME_POS 0.1  // Distance between nozzle and print surface after homing.
-
+#endif
 
 //// MOVEMENT SETTINGS
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
@@ -548,8 +551,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DEFAULT_RETRACT_ACCELERATION  2000   // E acceleration in mm/s^2 for retracts
 #define DEFAULT_TRAVEL_ACCELERATION   400    // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
 
-
-
 // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
 // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
 // For the other hotends it is their distance from the extruder 0 hotend.
@@ -571,8 +572,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #ifdef CUSTOM_M_CODES
   #ifdef ENABLE_AUTO_BED_LEVELING
     #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-    #define Z_PROBE_OFFSET_RANGE_MIN -15
+    #define Z_PROBE_OFFSET_RANGE_MIN -20
-    #define Z_PROBE_OFFSET_RANGE_MAX -5
+    #define Z_PROBE_OFFSET_RANGE_MAX 20
   #endif
 #endif
 
@@ -600,13 +601,16 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //==============================LCD and SD support=============================
 
 // Define your display language below. Replace (en) with your language code and uncomment.
-// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
+// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
 // See also language.h
 //#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Character based displays can have different extended charsets.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
-#define DISPLAY_CHARSET_HD44780_JAPAN     // "ääööüüß23°"
+// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
-//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
+// See also documentation/LCDLanguageFont.md
+  #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
+  //#define DISPLAY_CHARSET_HD44780_WESTERN
+  //#define DISPLAY_CHARSET_HD44780_CYRILLIC
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
@@ -619,6 +623,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+                                               // 0 to disable buzzer feedback  
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -681,7 +686,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define FAST_PWM_FAN
 
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
-// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
 //#define FAN_SOFT_PWM
 

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -100,6 +100,30 @@
 // On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
 //#define Z_DUAL_STEPPER_DRIVERS
 
+#ifdef Z_DUAL_STEPPER_DRIVERS
+
+  // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+  // That way the machine is capable to align the bed during home, since both Z steppers are homed. 
+  // There is also an implementation of M666 (software endstops adjustment) to this feature.
+  // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+  // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+  // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+  // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+  // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+  #define Z_DUAL_ENDSTOPS
+
+  #ifdef Z_DUAL_ENDSTOPS
+    #define Z2_STEP_PIN E2_STEP_PIN           // Stepper to be used to Z2 axis.
+    #define Z2_DIR_PIN E2_DIR_PIN
+    #define Z2_ENABLE_PIN E2_ENABLE_PIN
+    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
+    const bool Z2_MAX_ENDSTOP_INVERTING = false;
+    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+  #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
 // Same again but for Y Axis.
 //#define Y_DUAL_STEPPER_DRIVERS
 
@@ -159,8 +183,6 @@
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}
 
-#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
-
 //By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
 #define INVERT_X_STEP_PIN false
 #define INVERT_Y_STEP_PIN false
@@ -212,13 +234,21 @@
 //===========================================================================
 
 #define ENCODER_RATE_MULTIPLIER         // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
-#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value
+#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
-#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
 //#define ENCODER_RATE_MULTIPLIER_DEBUG  // If defined, output the encoder steps per second value
 
 //#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
 
+#ifdef SDSUPPORT
+
+  // If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+  // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+  // in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+  // be commented out otherwise
+  #define SDCARDDETECTINVERTED
+
   #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
@@ -227,7 +257,7 @@
   // using:
   //#define MENU_ADDAUTOSTART
 
-// Show a progress bar on the LCD when printing from SD?
+  // Show a progress bar on HD44780 LCDs for SD printing
   //#define LCD_PROGRESS_BAR
 
   #ifdef LCD_PROGRESS_BAR
@@ -241,6 +271,8 @@
     //#define PROGRESS_MSG_ONCE
   #endif
 
+#endif // SDSUPPORT
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -285,12 +317,6 @@
 
 const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
-// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
-// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
-// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
-// be commented out otherwise
-#define SDCARDDETECTINVERTED
-
 // Control heater 0 and heater 1 in parallel.
 //#define HEATERS_PARALLEL
 
@@ -300,7 +326,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 
 // The number of linear motions that can be in the plan at any give time.
 // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
-#if defined SDSUPPORT
+#ifdef SDSUPPORT
   #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
   #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
@@ -322,9 +348,11 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 #ifdef FWRETRACT
   #define MIN_RETRACT 0.1                //minimum extruded mm to accept a automatic gcode retraction attempt
   #define RETRACT_LENGTH 3               //default retract length (positive mm)
+  #define RETRACT_LENGTH_SWAP 13         //default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 35            //default feedrate for retracting (mm/s)
   #define RETRACT_ZLIFT 0                //default retract Z-lift
   #define RETRACT_RECOVER_LENGTH 0       //default additional recover length (mm, added to retract length when recovering)
+  #define RETRACT_RECOVER_LENGTH_SWAP 0  //default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
@@ -340,6 +368,139 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #endif
 #endif
 
+/******************************************************************************\
+ * enable this section if you have TMC26X motor drivers. 
+ * you need to import the TMC26XStepper library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_TMCDRIVER
+#ifdef HAVE_TMCDRIVER
+
+//	#define X_IS_TMC
+	#define X_MAX_CURRENT 1000  //in mA
+	#define X_SENSE_RESISTOR 91 //in mOhms
+	#define X_MICROSTEPS 16     //number of microsteps
+	
+//	#define X2_IS_TMC
+	#define X2_MAX_CURRENT 1000  //in mA
+	#define X2_SENSE_RESISTOR 91 //in mOhms
+	#define X2_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y_IS_TMC
+	#define Y_MAX_CURRENT 1000  //in mA
+	#define Y_SENSE_RESISTOR 91 //in mOhms
+	#define Y_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y2_IS_TMC
+	#define Y2_MAX_CURRENT 1000  //in mA
+	#define Y2_SENSE_RESISTOR 91 //in mOhms
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define Z_IS_TMC
+	#define Z_MAX_CURRENT 1000  //in mA
+	#define Z_SENSE_RESISTOR 91 //in mOhms
+	#define Z_MICROSTEPS 16     //number of microsteps
+	
+//	#define Z2_IS_TMC
+	#define Z2_MAX_CURRENT 1000  //in mA
+	#define Z2_SENSE_RESISTOR 91 //in mOhms
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	
+//	#define E0_IS_TMC
+	#define E0_MAX_CURRENT 1000  //in mA
+	#define E0_SENSE_RESISTOR 91 //in mOhms
+	#define E0_MICROSTEPS 16     //number of microsteps
+	
+//	#define E1_IS_TMC
+	#define E1_MAX_CURRENT 1000  //in mA
+	#define E1_SENSE_RESISTOR 91 //in mOhms
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E2_IS_TMC
+	#define E2_MAX_CURRENT 1000  //in mA
+	#define E2_SENSE_RESISTOR 91 //in mOhms
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E3_IS_TMC
+	#define E3_MAX_CURRENT 1000  //in mA
+	#define E3_SENSE_RESISTOR 91 //in mOhms
+	#define E3_MICROSTEPS 16     //number of microsteps		
+
+#endif
+
+/******************************************************************************\
+ * enable this section if you have L6470  motor drivers. 
+ * you need to import the L6470 library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_L6470DRIVER
+#ifdef HAVE_L6470DRIVER
+
+//	#define X_IS_L6470
+	#define X_MICROSTEPS 16     //number of microsteps
+	#define X_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define X2_IS_L6470
+	#define X2_MICROSTEPS 16     //number of microsteps
+	#define X2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y_IS_L6470
+	#define Y_MICROSTEPS 16     //number of microsteps
+	#define Y_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y2_IS_L6470
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	#define Y2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall	
+	
+//	#define Z_IS_L6470
+	#define Z_MICROSTEPS 16     //number of microsteps
+	#define Z_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Z2_IS_L6470
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	#define Z2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E0_IS_L6470
+	#define E0_MICROSTEPS 16     //number of microsteps
+	#define E0_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E0_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E1_IS_L6470
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	#define E1_MICROSTEPS 16     //number of microsteps
+	#define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E2_IS_L6470
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	#define E2_MICROSTEPS 16     //number of microsteps
+	#define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E3_IS_L6470
+	#define E3_MICROSTEPS 16     //number of microsteps		
+	#define E3_MICROSTEPS 16     //number of microsteps
+	#define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+#endif
+
 #include "Conditionals.h"
 #include "SanityCheck.h"
 

Marlin/example_configurations/WITBOX/Configuration.h

@@ -320,7 +320,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
   // #define ENDSTOPPULLUP_ZMIN
 #endif
 
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
@@ -343,13 +343,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DISABLE_E false // For all extruders
 #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
-#define INVERT_X_DIR true     // for Mendel set to false, for Orca set to true
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
+#define INVERT_X_DIR true
-#define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR false
-#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_Z_DIR true
-#define INVERT_E1_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E0_DIR false
-#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false
-#define INVERT_E3_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false
+#define INVERT_E3_DIR false
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -361,12 +362,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
 // Travel limits after homing (units are in mm)
-#define X_MAX_POS 297
 #define X_MIN_POS 0
-#define Y_MAX_POS 210
 #define Y_MIN_POS 0
-#define Z_MAX_POS 200
 #define Z_MIN_POS 0
+#define X_MAX_POS 297
+#define Y_MAX_POS 210
+#define Z_MAX_POS 200
 
 //===========================================================================
 //============================= Filament Runout Sensor ======================
@@ -432,7 +433,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
     // You probably don't need more than 3 (squared=9)
     #define AUTO_BED_LEVELING_GRID_POINTS 2
 
-
   #else  // !AUTO_BED_LEVELING_GRID
 
       // Arbitrary points to probe. A simple cross-product
@@ -446,11 +446,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #endif // AUTO_BED_LEVELING_GRID
 
-
   // Offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
-  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // -left  +right
+  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // Probe on: -left  +right
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // -front +behind
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Probe on: -front +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // -below (always!)
 
   #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
@@ -462,6 +461,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
   #define Z_RAISE_AFTER_PROBING 15    //How much the extruder will be raised after the last probing point.
 
+//   #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
+                                                                            //Useful to retract a deployable probe.
+                                                                           
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
@@ -498,10 +500,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 // Manual homing switch locations:
 // For deltabots this means top and center of the Cartesian print volume.
+#ifdef MANUAL_HOME_POSITIONS
   #define MANUAL_X_HOME_POS 0
   #define MANUAL_Y_HOME_POS 0
   #define MANUAL_Z_HOME_POS 0
   //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
+#endif
 
 //// MOVEMENT SETTINGS
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
@@ -538,8 +542,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #ifdef CUSTOM_M_CODES
   #ifdef ENABLE_AUTO_BED_LEVELING
     #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-    #define Z_PROBE_OFFSET_RANGE_MIN -15
+    #define Z_PROBE_OFFSET_RANGE_MIN -20
-    #define Z_PROBE_OFFSET_RANGE_MAX -5
+    #define Z_PROBE_OFFSET_RANGE_MAX 20
   #endif
 #endif
 
@@ -567,13 +571,16 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //==============================LCD and SD support=============================
 
 // Define your display language below. Replace (en) with your language code and uncomment.
-// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
+// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
 // See also language.h
 //#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Character based displays can have different extended charsets.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
-#define DISPLAY_CHARSET_HD44780_JAPAN     // "ääööüüß23°"
+// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
-//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
+// See also documentation/LCDLanguageFont.md
+  #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
+  //#define DISPLAY_CHARSET_HD44780_WESTERN
+  //#define DISPLAY_CHARSET_HD44780_CYRILLIC
 
 #define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
@@ -586,6 +593,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+                                               // 0 to disable buzzer feedback  
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -648,7 +656,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define FAST_PWM_FAN
 
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
-// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
 //#define FAN_SOFT_PWM
 

Marlin/example_configurations/WITBOX/Configuration_adv.h

@@ -100,6 +100,30 @@
 // On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
 //#define Z_DUAL_STEPPER_DRIVERS
 
+#ifdef Z_DUAL_STEPPER_DRIVERS
+
+  // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+  // That way the machine is capable to align the bed during home, since both Z steppers are homed. 
+  // There is also an implementation of M666 (software endstops adjustment) to this feature.
+  // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+  // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+  // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+  // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+  // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+  #define Z_DUAL_ENDSTOPS
+
+  #ifdef Z_DUAL_ENDSTOPS
+    #define Z2_STEP_PIN E2_STEP_PIN           // Stepper to be used to Z2 axis.
+    #define Z2_DIR_PIN E2_DIR_PIN
+    #define Z2_ENABLE_PIN E2_ENABLE_PIN
+    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
+    const bool Z2_MAX_ENDSTOP_INVERTING = false;
+    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+  #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
 // Same again but for Y Axis.
 //#define Y_DUAL_STEPPER_DRIVERS
 
@@ -158,11 +182,7 @@
 //#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}
-#ifdef CONFIG_STEPPERS_TOSHIBA
+
-#define MAX_STEP_FREQUENCY 10000 // Max step frequency for Toshiba Stepper Controllers
-#else
-#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
-#endif
 //By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
 #define INVERT_X_STEP_PIN false
 #define INVERT_Y_STEP_PIN false
@@ -214,20 +234,28 @@
 //===========================================================================
 
 #define ENCODER_RATE_MULTIPLIER         // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
-#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value
+#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
-#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
 //#define ENCODER_RATE_MULTIPLIER_DEBUG  // If defined, output the encoder steps per second value
 
 //#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
 
+#ifdef SDSUPPORT
+
+  // If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+  // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+  // in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+  // be commented out otherwise
+  #define SDCARDDETECTINVERTED
+
   #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
   #define SDCARD_RATHERRECENTFIRST  //reverse file order of sd card menu display. Its sorted practically after the file system block order.
   // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
   // using:
-#define MENU_ADDAUTOSTART
+  //#define MENU_ADDAUTOSTART
 
   // Show a progress bar on HD44780 LCDs for SD printing
   //#define LCD_PROGRESS_BAR
@@ -243,6 +271,8 @@
     //#define PROGRESS_MSG_ONCE
   #endif
 
+#endif // SDSUPPORT
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -279,7 +309,7 @@
   #define EXTRUDER_ADVANCE_K .0
   #define D_FILAMENT 1.75
   #define STEPS_MM_E 100.47095761381482
-#endif // ADVANCE
+#endif
 
 // Arc interpretation settings:
 #define MM_PER_ARC_SEGMENT 1
@@ -287,12 +317,6 @@
 
 const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
-// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
-// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
-// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
-// be commented out otherwise
-#define SDCARDDETECTINVERTED
-
 // Control heater 0 and heater 1 in parallel.
 //#define HEATERS_PARALLEL
 
@@ -302,7 +326,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 
 // The number of linear motions that can be in the plan at any give time.
 // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
-#if defined SDSUPPORT
+#ifdef SDSUPPORT
   #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
   #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
@@ -344,6 +368,139 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #endif
 #endif
 
+/******************************************************************************\
+ * enable this section if you have TMC26X motor drivers. 
+ * you need to import the TMC26XStepper library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_TMCDRIVER
+#ifdef HAVE_TMCDRIVER
+
+//	#define X_IS_TMC
+	#define X_MAX_CURRENT 1000  //in mA
+	#define X_SENSE_RESISTOR 91 //in mOhms
+	#define X_MICROSTEPS 16     //number of microsteps
+	
+//	#define X2_IS_TMC
+	#define X2_MAX_CURRENT 1000  //in mA
+	#define X2_SENSE_RESISTOR 91 //in mOhms
+	#define X2_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y_IS_TMC
+	#define Y_MAX_CURRENT 1000  //in mA
+	#define Y_SENSE_RESISTOR 91 //in mOhms
+	#define Y_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y2_IS_TMC
+	#define Y2_MAX_CURRENT 1000  //in mA
+	#define Y2_SENSE_RESISTOR 91 //in mOhms
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define Z_IS_TMC
+	#define Z_MAX_CURRENT 1000  //in mA
+	#define Z_SENSE_RESISTOR 91 //in mOhms
+	#define Z_MICROSTEPS 16     //number of microsteps
+	
+//	#define Z2_IS_TMC
+	#define Z2_MAX_CURRENT 1000  //in mA
+	#define Z2_SENSE_RESISTOR 91 //in mOhms
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	
+//	#define E0_IS_TMC
+	#define E0_MAX_CURRENT 1000  //in mA
+	#define E0_SENSE_RESISTOR 91 //in mOhms
+	#define E0_MICROSTEPS 16     //number of microsteps
+	
+//	#define E1_IS_TMC
+	#define E1_MAX_CURRENT 1000  //in mA
+	#define E1_SENSE_RESISTOR 91 //in mOhms
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E2_IS_TMC
+	#define E2_MAX_CURRENT 1000  //in mA
+	#define E2_SENSE_RESISTOR 91 //in mOhms
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E3_IS_TMC
+	#define E3_MAX_CURRENT 1000  //in mA
+	#define E3_SENSE_RESISTOR 91 //in mOhms
+	#define E3_MICROSTEPS 16     //number of microsteps		
+
+#endif
+
+/******************************************************************************\
+ * enable this section if you have L6470  motor drivers. 
+ * you need to import the L6470 library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_L6470DRIVER
+#ifdef HAVE_L6470DRIVER
+
+//	#define X_IS_L6470
+	#define X_MICROSTEPS 16     //number of microsteps
+	#define X_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define X2_IS_L6470
+	#define X2_MICROSTEPS 16     //number of microsteps
+	#define X2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y_IS_L6470
+	#define Y_MICROSTEPS 16     //number of microsteps
+	#define Y_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y2_IS_L6470
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	#define Y2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall	
+	
+//	#define Z_IS_L6470
+	#define Z_MICROSTEPS 16     //number of microsteps
+	#define Z_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Z2_IS_L6470
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	#define Z2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E0_IS_L6470
+	#define E0_MICROSTEPS 16     //number of microsteps
+	#define E0_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E0_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E1_IS_L6470
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	#define E1_MICROSTEPS 16     //number of microsteps
+	#define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E2_IS_L6470
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	#define E2_MICROSTEPS 16     //number of microsteps
+	#define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E3_IS_L6470
+	#define E3_MICROSTEPS 16     //number of microsteps		
+	#define E3_MICROSTEPS 16     //number of microsteps
+	#define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+#endif
+
 #include "Conditionals.h"
 #include "SanityCheck.h"
 

Marlin/example_configurations/delta/generic/Configuration.h

@@ -348,7 +348,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
   // #define ENDSTOPPULLUP_ZMIN
 #endif
 
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
@@ -371,19 +371,18 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DISABLE_E false // For all extruders
 #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
 #define INVERT_X_DIR false // DELTA does not invert
 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
-
+#define INVERT_E0_DIR false
-#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false
-#define INVERT_E1_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false
-#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E3_DIR false
-#define INVERT_E3_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
-// deltas always home to max
+#define X_HOME_DIR 1 // deltas always home to max
-#define X_HOME_DIR 1
 #define Y_HOME_DIR 1
 #define Z_HOME_DIR 1
 
@@ -391,12 +390,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
 // Travel limits after homing (units are in mm)
-#define X_MAX_POS DELTA_PRINTABLE_RADIUS
 #define X_MIN_POS -DELTA_PRINTABLE_RADIUS
-#define Y_MAX_POS DELTA_PRINTABLE_RADIUS
 #define Y_MIN_POS -DELTA_PRINTABLE_RADIUS
-#define Z_MAX_POS MANUAL_Z_HOME_POS
 #define Z_MIN_POS 0
+#define X_MAX_POS DELTA_PRINTABLE_RADIUS
+#define Y_MAX_POS DELTA_PRINTABLE_RADIUS
+#define Z_MAX_POS MANUAL_Z_HOME_POS
 
 //===========================================================================
 //============================= Filament Runout Sensor ======================
@@ -430,18 +429,33 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //===========================================================================
 
 //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
-// Z-Probe Repeatability test is not supported in Deltas yet.
+//#define Z_PROBE_REPEATABILITY_TEST // Z-Probe Repeatability test is not supported in Deltas yet.
 
 #ifdef ENABLE_AUTO_BED_LEVELING
 
-  // Deltas only support grid mode
+  // There are 2 different ways to specify probing locations
-  #define AUTO_BED_LEVELING_GRID
+  //
+  // - "grid" mode
+  //   Probe several points in a rectangular grid.
+  //   You specify the rectangle and the density of sample points.
+  //   This mode is preferred because there are more measurements.
+  //
+  // - "3-point" mode
+  //   Probe 3 arbitrary points on the bed (that aren't colinear)
+  //   You specify the XY coordinates of all 3 points.
+
+  // Enable this to sample the bed in a grid (least squares solution)
+  // Note: this feature generates 10KB extra code size
+  #define AUTO_BED_LEVELING_GRID  // Deltas only support grid mode
+
+  #ifdef AUTO_BED_LEVELING_GRID
 
     #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
+
     #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
     #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
-  #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
     #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
+    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
     
     #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
 
@@ -451,10 +465,23 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
     // Works best with ACCURATE_BED_LEVELING_POINTS 5 or higher.
     #define AUTO_BED_LEVELING_GRID_POINTS 9
 
+  #else  // !AUTO_BED_LEVELING_GRID
+
+      // Arbitrary points to probe. A simple cross-product
+      // is used to estimate the plane of the bed.
+      #define ABL_PROBE_PT_1_X 15
+      #define ABL_PROBE_PT_1_Y 180
+      #define ABL_PROBE_PT_2_X 15
+      #define ABL_PROBE_PT_2_Y 20
+      #define ABL_PROBE_PT_3_X 170
+      #define ABL_PROBE_PT_3_Y 20
+
+  #endif // AUTO_BED_LEVELING_GRID
+
   // Offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
-  #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // -left  +right
+  #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // Probe on: -left  +right
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // -front +behind
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Probe on: -front +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5  // -below (always!)
 
   #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
@@ -466,6 +493,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
   #define Z_RAISE_AFTER_PROBING 50    //How much the extruder will be raised after the last probing point.
 
+//   #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
+                                                                            //Useful to retract a deployable probe.
+                                                                           
+  //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
+  //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
+
   // Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
   // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
   //#define Z_PROBE_ALLEN_KEY
@@ -507,16 +540,17 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #endif // ENABLE_AUTO_BED_LEVELING
 
 
-
 // The position of the homing switches
 #define MANUAL_HOME_POSITIONS  // If defined, MANUAL_*_HOME_POS below will be used
 //#define BED_CENTER_AT_0_0  // If defined, the center of the bed is at (X=0, Y=0)
 
 // Manual homing switch locations:
 // For deltabots this means top and center of the Cartesian print volume.
+#ifdef MANUAL_HOME_POSITIONS
   #define MANUAL_X_HOME_POS 0
   #define MANUAL_Y_HOME_POS 0
   #define MANUAL_Z_HOME_POS 250 // For delta: Distance between nozzle and print surface after homing.
+#endif
 
 //// MOVEMENT SETTINGS
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
@@ -555,8 +589,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #ifdef CUSTOM_M_CODES
   #ifdef ENABLE_AUTO_BED_LEVELING
     #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-    #define Z_PROBE_OFFSET_RANGE_MIN -15
+    #define Z_PROBE_OFFSET_RANGE_MIN -20
-    #define Z_PROBE_OFFSET_RANGE_MAX -5
+    #define Z_PROBE_OFFSET_RANGE_MAX 20
   #endif
 #endif
 
@@ -588,7 +622,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 // See also language.h
 #define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Chose ONE of the next three charsets. This has to match your hardware. In case of a full graphic display this information is not important.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
 // To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
 // See also documentation/LCDLanguageFont.md
   #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
@@ -606,6 +640,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+                                               // 0 to disable buzzer feedback  
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -675,7 +710,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define FAST_PWM_FAN
 
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
-// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
 //#define FAN_SOFT_PWM
 

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -22,7 +22,7 @@
 
 #ifdef PIDTEMP
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
-  // if Kc is choosen well, the additional required power due to increased melting should be compensated.
+  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
   #define PID_ADD_EXTRUSION_RATE
   #ifdef PID_ADD_EXTRUSION_RATE
     #define  DEFAULT_Kc (1) //heating power=Kc*(e_speed)
@@ -32,11 +32,11 @@
 
 //automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
 //The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
+//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
 // the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
 // you exit the value by any M109 without F*
 // Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
 #define AUTOTEMP
 #ifdef AUTOTEMP
   #define AUTOTEMP_OLDWEIGHT 0.98
@@ -100,6 +100,30 @@
 // On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
 //#define Z_DUAL_STEPPER_DRIVERS
 
+#ifdef Z_DUAL_STEPPER_DRIVERS
+
+  // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+  // That way the machine is capable to align the bed during home, since both Z steppers are homed. 
+  // There is also an implementation of M666 (software endstops adjustment) to this feature.
+  // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+  // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+  // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+  // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+  // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+  #define Z_DUAL_ENDSTOPS
+
+  #ifdef Z_DUAL_ENDSTOPS
+    #define Z2_STEP_PIN E2_STEP_PIN           // Stepper to be used to Z2 axis.
+    #define Z2_DIR_PIN E2_DIR_PIN
+    #define Z2_ENABLE_PIN E2_ENABLE_PIN
+    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
+    const bool Z2_MAX_ENDSTOP_INVERTING = false;
+    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+  #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
 // Same again but for Y Axis.
 //#define Y_DUAL_STEPPER_DRIVERS
 
@@ -155,13 +179,10 @@
 #define Y_HOME_RETRACT_MM 5
 #define Z_HOME_RETRACT_MM 5 // deltas need the same for all three axis
 #define HOMING_BUMP_DIVISOR {10, 10, 20}  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
-
 //#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}
 
-#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
-
 //By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
 #define INVERT_X_STEP_PIN false
 #define INVERT_Y_STEP_PIN false
@@ -174,9 +195,9 @@
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
 #define DEFAULT_MINTRAVELFEEDRATE     0.0
 
-// Feedrates for manual moves along X, Y, Z, E from panel
 #ifdef ULTIPANEL
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif
 
 // minimum time in microseconds that a movement needs to take if the buffer is emptied.
@@ -214,36 +235,46 @@
 //===========================================================================
 
 #define ENCODER_RATE_MULTIPLIER         // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
-#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value
+#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
-#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
 //#define ENCODER_RATE_MULTIPLIER_DEBUG  // If defined, output the encoder steps per second value
 
 //#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
 
+#ifdef SDSUPPORT
+
+  // If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+  // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+  // in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+  // be commented out otherwise
+  #define SDCARDDETECTINVERTED
+
   #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
   #define SDCARD_RATHERRECENTFIRST  //reverse file order of sd card menu display. Its sorted practically after the file system block order.
-// if a file is deleted, it frees a block. hence, the order is not purely cronological. To still have auto0.g accessible, there is again the option to do that.
+  // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
   // using:
   //#define MENU_ADDAUTOSTART
 
-// Show a progress bar on the LCD when printing from SD
+  // Show a progress bar on HD44780 LCDs for SD printing
   //#define LCD_PROGRESS_BAR
 
   #ifdef LCD_PROGRESS_BAR
     // Amount of time (ms) to show the bar
     #define PROGRESS_BAR_BAR_TIME 2000
     // Amount of time (ms) to show the status message
-  #define PROGRESS_BAR_MSG_TIME 2000
+    #define PROGRESS_BAR_MSG_TIME 3000
     // Amount of time (ms) to retain the status message (0=forever)
     #define PROGRESS_MSG_EXPIRE   0
     // Enable this to show messages for MSG_TIME then hide them
     //#define PROGRESS_MSG_ONCE
   #endif
 
-// The hardware watchdog should reset the Microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
+#endif // SDSUPPORT
+
+// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
 #ifdef USE_WATCHDOG
@@ -257,7 +288,7 @@
 //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
 
 // Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
-// it can e.g. be used to change z-positions in the print startup phase in realtime
+// it can e.g. be used to change z-positions in the print startup phase in real-time
 // does not respect endstops!
 //#define BABYSTEPPING
 #ifdef BABYSTEPPING
@@ -270,7 +301,7 @@
 //
 // advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
 //
-// hooke's law says:		force = k * distance
+// Hooke's law says:		force = k * distance
 // Bernoulli's principle says:	v ^ 2 / 2 + g . h + pressure / density = constant
 // so: v ^ 2 is proportional to number of steps we advance the extruder
 //#define ADVANCE
@@ -279,7 +310,7 @@
   #define EXTRUDER_ADVANCE_K .0
   #define D_FILAMENT 2.85
   #define STEPS_MM_E 836
-#endif // ADVANCE
+#endif
 
 // Arc interpretation settings:
 #define MM_PER_ARC_SEGMENT 1
@@ -287,12 +318,6 @@
 
 const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
-// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
-// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT 
-// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
-// be commented out otherwise
-#define SDCARDDETECTINVERTED 
-
 // Control heater 0 and heater 1 in parallel.
 //#define HEATERS_PARALLEL
 
@@ -301,20 +326,20 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 //===========================================================================
 
 // The number of linear motions that can be in the plan at any give time.
-// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
+// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
-#if defined SDSUPPORT
+#ifdef SDSUPPORT
   #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
   #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
 #endif
 
 
-//The ASCII buffer for recieving from the serial:
+//The ASCII buffer for receiving from the serial:
 #define MAX_CMD_SIZE 96
 #define BUFSIZE 4
 
 
-// Firmware based and LCD controled retract
+// Firmware based and LCD controlled retract
 // M207 and M208 can be used to define parameters for the retraction.
 // The retraction can be called by the slicer using G10 and G11
 // until then, intended retractions can be detected by moves that only extrude and the direction.
@@ -344,6 +369,139 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #endif
 #endif
 
+/******************************************************************************\
+ * enable this section if you have TMC26X motor drivers. 
+ * you need to import the TMC26XStepper library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_TMCDRIVER
+#ifdef HAVE_TMCDRIVER
+
+//	#define X_IS_TMC
+	#define X_MAX_CURRENT 1000  //in mA
+	#define X_SENSE_RESISTOR 91 //in mOhms
+	#define X_MICROSTEPS 16     //number of microsteps
+	
+//	#define X2_IS_TMC
+	#define X2_MAX_CURRENT 1000  //in mA
+	#define X2_SENSE_RESISTOR 91 //in mOhms
+	#define X2_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y_IS_TMC
+	#define Y_MAX_CURRENT 1000  //in mA
+	#define Y_SENSE_RESISTOR 91 //in mOhms
+	#define Y_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y2_IS_TMC
+	#define Y2_MAX_CURRENT 1000  //in mA
+	#define Y2_SENSE_RESISTOR 91 //in mOhms
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define Z_IS_TMC
+	#define Z_MAX_CURRENT 1000  //in mA
+	#define Z_SENSE_RESISTOR 91 //in mOhms
+	#define Z_MICROSTEPS 16     //number of microsteps
+	
+//	#define Z2_IS_TMC
+	#define Z2_MAX_CURRENT 1000  //in mA
+	#define Z2_SENSE_RESISTOR 91 //in mOhms
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	
+//	#define E0_IS_TMC
+	#define E0_MAX_CURRENT 1000  //in mA
+	#define E0_SENSE_RESISTOR 91 //in mOhms
+	#define E0_MICROSTEPS 16     //number of microsteps
+	
+//	#define E1_IS_TMC
+	#define E1_MAX_CURRENT 1000  //in mA
+	#define E1_SENSE_RESISTOR 91 //in mOhms
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E2_IS_TMC
+	#define E2_MAX_CURRENT 1000  //in mA
+	#define E2_SENSE_RESISTOR 91 //in mOhms
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E3_IS_TMC
+	#define E3_MAX_CURRENT 1000  //in mA
+	#define E3_SENSE_RESISTOR 91 //in mOhms
+	#define E3_MICROSTEPS 16     //number of microsteps		
+
+#endif
+
+/******************************************************************************\
+ * enable this section if you have L6470  motor drivers. 
+ * you need to import the L6470 library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_L6470DRIVER
+#ifdef HAVE_L6470DRIVER
+
+//	#define X_IS_L6470
+	#define X_MICROSTEPS 16     //number of microsteps
+	#define X_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define X2_IS_L6470
+	#define X2_MICROSTEPS 16     //number of microsteps
+	#define X2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y_IS_L6470
+	#define Y_MICROSTEPS 16     //number of microsteps
+	#define Y_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y2_IS_L6470
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	#define Y2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall	
+	
+//	#define Z_IS_L6470
+	#define Z_MICROSTEPS 16     //number of microsteps
+	#define Z_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Z2_IS_L6470
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	#define Z2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E0_IS_L6470
+	#define E0_MICROSTEPS 16     //number of microsteps
+	#define E0_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E0_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E1_IS_L6470
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	#define E1_MICROSTEPS 16     //number of microsteps
+	#define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E2_IS_L6470
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	#define E2_MICROSTEPS 16     //number of microsteps
+	#define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E3_IS_L6470
+	#define E3_MICROSTEPS 16     //number of microsteps		
+	#define E3_MICROSTEPS 16     //number of microsteps
+	#define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+#endif
+
 #include "Conditionals.h"
 #include "SanityCheck.h"
 

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -348,7 +348,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
   // #define ENDSTOPPULLUP_ZMIN
 #endif
 
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
@@ -371,19 +371,18 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define DISABLE_E false // For all extruders
 #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
 #define INVERT_X_DIR false // DELTA does not invert
 #define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
-
+#define INVERT_E0_DIR false
-#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false
-#define INVERT_E1_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false
-#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E3_DIR false
-#define INVERT_E3_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
-// deltas always home to max
+#define X_HOME_DIR 1  // deltas always home to max
-#define X_HOME_DIR 1
 #define Y_HOME_DIR 1
 #define Z_HOME_DIR 1
 
@@ -391,12 +390,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
 // Travel limits after homing (units are in mm)
-#define X_MAX_POS DELTA_PRINTABLE_RADIUS
 #define X_MIN_POS -DELTA_PRINTABLE_RADIUS
-#define Y_MAX_POS DELTA_PRINTABLE_RADIUS
 #define Y_MIN_POS -DELTA_PRINTABLE_RADIUS
-#define Z_MAX_POS MANUAL_Z_HOME_POS
 #define Z_MIN_POS 0
+#define X_MAX_POS DELTA_PRINTABLE_RADIUS
+#define Y_MAX_POS DELTA_PRINTABLE_RADIUS
+#define Z_MAX_POS MANUAL_Z_HOME_POS
 
 //===========================================================================
 //============================= Filament Runout Sensor ======================
@@ -430,18 +429,33 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 //===========================================================================
 
 #define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
-// Z-Probe Repeatability test is not supported in Deltas yet.
+// #define Z_PROBE_REPEATABILITY_TEST // Z-Probe Repeatability test is not supported in Deltas yet.
 
 #ifdef ENABLE_AUTO_BED_LEVELING
 
-  // Deltas only support grid mode
+  // There are 2 different ways to specify probing locations
-  #define AUTO_BED_LEVELING_GRID
+  //
+  // - "grid" mode
+  //   Probe several points in a rectangular grid.
+  //   You specify the rectangle and the density of sample points.
+  //   This mode is preferred because there are more measurements.
+  //
+  // - "3-point" mode
+  //   Probe 3 arbitrary points on the bed (that aren't colinear)
+  //   You specify the XY coordinates of all 3 points.
+
+  // Enable this to sample the bed in a grid (least squares solution)
+  // Note: this feature generates 10KB extra code size
+  #define AUTO_BED_LEVELING_GRID  // Deltas only support grid mode
+
+  #ifdef AUTO_BED_LEVELING_GRID
 
     #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
+
     #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
     #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
-  #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
     #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS  
+    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
 
     #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this      
 
@@ -451,10 +465,23 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
     // Works best with ACCURATE_BED_LEVELING_POINTS 5 or higher.
     #define AUTO_BED_LEVELING_GRID_POINTS 9
 
+  #else  // !AUTO_BED_LEVELING_GRID
+
+      // Arbitrary points to probe. A simple cross-product
+      // is used to estimate the plane of the bed.
+      #define ABL_PROBE_PT_1_X 15
+      #define ABL_PROBE_PT_1_Y 180
+      #define ABL_PROBE_PT_2_X 15
+      #define ABL_PROBE_PT_2_Y 20
+      #define ABL_PROBE_PT_3_X 170
+      #define ABL_PROBE_PT_3_Y 20
+
+  #endif // AUTO_BED_LEVELING_GRID
+
   // Offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
-  #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // -left  +right
+  #define X_PROBE_OFFSET_FROM_EXTRUDER 0     // Probe on: -left  +right
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // -front +behind
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -10   // Probe on: -front +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5  // -below (always!)
 
   #define Z_RAISE_BEFORE_HOMING 15      // (in mm) Raise Z before homing (G28) for Probe Clearance.
@@ -466,6 +493,16 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
   #define Z_RAISE_AFTER_PROBING 50    //How much the extruder will be raised after the last probing point.
 
+//   #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
+                                                                            //Useful to retract a deployable probe.
+                                                                           
+  //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
+  //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
+
+  //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
+  //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
+  // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
+
   // Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
   // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
   #define Z_PROBE_ALLEN_KEY
@@ -507,16 +544,17 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #endif // ENABLE_AUTO_BED_LEVELING
 
 
-
 // The position of the homing switches
 #define MANUAL_HOME_POSITIONS  // If defined, MANUAL_*_HOME_POS below will be used
 #define BED_CENTER_AT_0_0  // If defined, the center of the bed is at (X=0, Y=0)
 
 // Manual homing switch locations:
 // For deltabots this means top and center of the Cartesian print volume.
+#ifdef MANUAL_HOME_POSITIONS
   #define MANUAL_X_HOME_POS 0
   #define MANUAL_Y_HOME_POS 0
   #define MANUAL_Z_HOME_POS 250 // For delta: Distance between nozzle and print surface after homing.
+#endif
 
 //// MOVEMENT SETTINGS
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
@@ -555,8 +593,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #ifdef CUSTOM_M_CODES
   #ifdef ENABLE_AUTO_BED_LEVELING
     #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-    #define Z_PROBE_OFFSET_RANGE_MIN -15
+    #define Z_PROBE_OFFSET_RANGE_MIN -20
-    #define Z_PROBE_OFFSET_RANGE_MAX -5
+    #define Z_PROBE_OFFSET_RANGE_MAX 20
   #endif
 #endif
 
@@ -588,7 +626,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 // See also language.h
 #define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Chose ONE of the next three charsets. This has to match your hardware. In case of a full graphic display this information is not important.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
 // To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
 // See also documentation/LCDLanguageFont.md
   #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
@@ -606,6 +644,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+                                               // 0 to disable buzzer feedback  
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -675,7 +714,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 //#define FAST_PWM_FAN
 
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
-// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
 //#define FAN_SOFT_PWM
 

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -22,7 +22,7 @@
 
 #ifdef PIDTEMP
   // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
-  // if Kc is choosen well, the additional required power due to increased melting should be compensated.
+  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
   #define PID_ADD_EXTRUSION_RATE
   #ifdef PID_ADD_EXTRUSION_RATE
     #define  DEFAULT_Kc (1) //heating power=Kc*(e_speed)
@@ -32,11 +32,11 @@
 
 //automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
 //The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
+//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
 // the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
 // you exit the value by any M109 without F*
 // Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
 #define AUTOTEMP
 #ifdef AUTOTEMP
   #define AUTOTEMP_OLDWEIGHT 0.98
@@ -100,6 +100,30 @@
 // On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
 //#define Z_DUAL_STEPPER_DRIVERS
 
+#ifdef Z_DUAL_STEPPER_DRIVERS
+
+  // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+  // That way the machine is capable to align the bed during home, since both Z steppers are homed. 
+  // There is also an implementation of M666 (software endstops adjustment) to this feature.
+  // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+  // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+  // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+  // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+  // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+  #define Z_DUAL_ENDSTOPS
+
+  #ifdef Z_DUAL_ENDSTOPS
+    #define Z2_STEP_PIN E2_STEP_PIN           // Stepper to be used to Z2 axis.
+    #define Z2_DIR_PIN E2_DIR_PIN
+    #define Z2_ENABLE_PIN E2_ENABLE_PIN
+    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
+    const bool Z2_MAX_ENDSTOP_INVERTING = false;
+    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+  #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
 // Same again but for Y Axis.
 //#define Y_DUAL_STEPPER_DRIVERS
 
@@ -155,13 +179,10 @@
 #define Y_HOME_RETRACT_MM 5
 #define Z_HOME_RETRACT_MM 5 // deltas need the same for all three axis
 #define HOMING_BUMP_DIVISOR {10, 10, 20}  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
-
 //#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}
 
-#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
-
 //By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
 #define INVERT_X_STEP_PIN false
 #define INVERT_Y_STEP_PIN false
@@ -174,9 +195,9 @@
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
 #define DEFAULT_MINTRAVELFEEDRATE     0.0
 
-// Feedrates for manual moves along X, Y, Z, E from panel
 #ifdef ULTIPANEL
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif
 
 // minimum time in microseconds that a movement needs to take if the buffer is emptied.
@@ -213,36 +234,46 @@
 //===========================================================================
 
 #define ENCODER_RATE_MULTIPLIER         // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
-#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value
+#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
-#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
 //#define ENCODER_RATE_MULTIPLIER_DEBUG  // If defined, output the encoder steps per second value
 
 //#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
 
+#ifdef SDSUPPORT
+
+  // If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+  // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+  // in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+  // be commented out otherwise
+  #define SDCARDDETECTINVERTED
+
   #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
   #define SDCARD_RATHERRECENTFIRST  //reverse file order of sd card menu display. Its sorted practically after the file system block order.
-// if a file is deleted, it frees a block. hence, the order is not purely cronological. To still have auto0.g accessible, there is again the option to do that.
+  // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
   // using:
   //#define MENU_ADDAUTOSTART
 
-// Show a progress bar on the LCD when printing from SD
+  // Show a progress bar on HD44780 LCDs for SD printing
   //#define LCD_PROGRESS_BAR
 
   #ifdef LCD_PROGRESS_BAR
     // Amount of time (ms) to show the bar
     #define PROGRESS_BAR_BAR_TIME 2000
     // Amount of time (ms) to show the status message
-  #define PROGRESS_BAR_MSG_TIME 2000
+    #define PROGRESS_BAR_MSG_TIME 3000
     // Amount of time (ms) to retain the status message (0=forever)
     #define PROGRESS_MSG_EXPIRE   0
     // Enable this to show messages for MSG_TIME then hide them
     //#define PROGRESS_MSG_ONCE
   #endif
 
-// The hardware watchdog should reset the Microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
+#endif // SDSUPPORT
+
+// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
 #ifdef USE_WATCHDOG
@@ -256,7 +287,7 @@
 //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
 
 // Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
-// it can e.g. be used to change z-positions in the print startup phase in realtime
+// it can e.g. be used to change z-positions in the print startup phase in real-time
 // does not respect endstops!
 //#define BABYSTEPPING
 #ifdef BABYSTEPPING
@@ -269,7 +300,7 @@
 //
 // advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
 //
-// hooke's law says:		force = k * distance
+// Hooke's law says:		force = k * distance
 // Bernoulli's principle says:	v ^ 2 / 2 + g . h + pressure / density = constant
 // so: v ^ 2 is proportional to number of steps we advance the extruder
 //#define ADVANCE
@@ -278,7 +309,7 @@
   #define EXTRUDER_ADVANCE_K .0
   #define D_FILAMENT 2.85
   #define STEPS_MM_E 836
-#endif // ADVANCE
+#endif
 
 // Arc interpretation settings:
 #define MM_PER_ARC_SEGMENT 1
@@ -286,12 +317,6 @@
 
 const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
-// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
-// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT 
-// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
-// be commented out otherwise
-#define SDCARDDETECTINVERTED 
-
 // Control heater 0 and heater 1 in parallel.
 //#define HEATERS_PARALLEL
 
@@ -300,20 +325,20 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 //===========================================================================
 
 // The number of linear motions that can be in the plan at any give time.
-// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
+// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
-#if defined SDSUPPORT
+#ifdef SDSUPPORT
   #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
   #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
 #endif
 
 
-//The ASCII buffer for recieving from the serial:
+//The ASCII buffer for receiving from the serial:
 #define MAX_CMD_SIZE 96
 #define BUFSIZE 4
 
 
-// Firmware based and LCD controled retract
+// Firmware based and LCD controlled retract
 // M207 and M208 can be used to define parameters for the retraction.
 // The retraction can be called by the slicer using G10 and G11
 // until then, intended retractions can be detected by moves that only extrude and the direction.
@@ -343,6 +368,139 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #endif
 #endif
 
+/******************************************************************************\
+ * enable this section if you have TMC26X motor drivers. 
+ * you need to import the TMC26XStepper library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_TMCDRIVER
+#ifdef HAVE_TMCDRIVER
+
+//	#define X_IS_TMC
+	#define X_MAX_CURRENT 1000  //in mA
+	#define X_SENSE_RESISTOR 91 //in mOhms
+	#define X_MICROSTEPS 16     //number of microsteps
+	
+//	#define X2_IS_TMC
+	#define X2_MAX_CURRENT 1000  //in mA
+	#define X2_SENSE_RESISTOR 91 //in mOhms
+	#define X2_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y_IS_TMC
+	#define Y_MAX_CURRENT 1000  //in mA
+	#define Y_SENSE_RESISTOR 91 //in mOhms
+	#define Y_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y2_IS_TMC
+	#define Y2_MAX_CURRENT 1000  //in mA
+	#define Y2_SENSE_RESISTOR 91 //in mOhms
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define Z_IS_TMC
+	#define Z_MAX_CURRENT 1000  //in mA
+	#define Z_SENSE_RESISTOR 91 //in mOhms
+	#define Z_MICROSTEPS 16     //number of microsteps
+	
+//	#define Z2_IS_TMC
+	#define Z2_MAX_CURRENT 1000  //in mA
+	#define Z2_SENSE_RESISTOR 91 //in mOhms
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	
+//	#define E0_IS_TMC
+	#define E0_MAX_CURRENT 1000  //in mA
+	#define E0_SENSE_RESISTOR 91 //in mOhms
+	#define E0_MICROSTEPS 16     //number of microsteps
+	
+//	#define E1_IS_TMC
+	#define E1_MAX_CURRENT 1000  //in mA
+	#define E1_SENSE_RESISTOR 91 //in mOhms
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E2_IS_TMC
+	#define E2_MAX_CURRENT 1000  //in mA
+	#define E2_SENSE_RESISTOR 91 //in mOhms
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E3_IS_TMC
+	#define E3_MAX_CURRENT 1000  //in mA
+	#define E3_SENSE_RESISTOR 91 //in mOhms
+	#define E3_MICROSTEPS 16     //number of microsteps		
+
+#endif
+
+/******************************************************************************\
+ * enable this section if you have L6470  motor drivers. 
+ * you need to import the L6470 library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_L6470DRIVER
+#ifdef HAVE_L6470DRIVER
+
+//	#define X_IS_L6470
+	#define X_MICROSTEPS 16     //number of microsteps
+	#define X_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define X2_IS_L6470
+	#define X2_MICROSTEPS 16     //number of microsteps
+	#define X2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y_IS_L6470
+	#define Y_MICROSTEPS 16     //number of microsteps
+	#define Y_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y2_IS_L6470
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	#define Y2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall	
+	
+//	#define Z_IS_L6470
+	#define Z_MICROSTEPS 16     //number of microsteps
+	#define Z_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Z2_IS_L6470
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	#define Z2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E0_IS_L6470
+	#define E0_MICROSTEPS 16     //number of microsteps
+	#define E0_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E0_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E1_IS_L6470
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	#define E1_MICROSTEPS 16     //number of microsteps
+	#define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E2_IS_L6470
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	#define E2_MICROSTEPS 16     //number of microsteps
+	#define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E3_IS_L6470
+	#define E3_MICROSTEPS 16     //number of microsteps		
+	#define E3_MICROSTEPS 16     //number of microsteps
+	#define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+#endif
+
 #include "Conditionals.h"
 #include "SanityCheck.h"
 

Marlin/example_configurations/makibox/Configuration.h

@@ -318,7 +318,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
   // #define ENDSTOPPULLUP_ZMIN
 #endif
 
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
@@ -341,13 +341,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DISABLE_E false // For all extruders
 #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
-#define INVERT_X_DIR false    // for Mendel set to false, for Orca set to true
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
+#define INVERT_X_DIR false
-#define INVERT_Z_DIR false    // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR false
-#define INVERT_E0_DIR true    // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_Z_DIR false
-#define INVERT_E1_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E0_DIR true
-#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false
-#define INVERT_E3_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false
+#define INVERT_E3_DIR false
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -359,12 +360,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
 // Travel limits after homing (units are in mm)
-#define X_MAX_POS 110
 #define X_MIN_POS 0
-#define Y_MAX_POS 150
 #define Y_MIN_POS 0
-#define Z_MAX_POS 86
 #define Z_MIN_POS 0
+#define X_MAX_POS 110
+#define Y_MAX_POS 150
+#define Z_MAX_POS 86
 
 //===========================================================================
 //============================= Filament Runout Sensor ======================
@@ -430,7 +431,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
     // You probably don't need more than 3 (squared=9)
     #define AUTO_BED_LEVELING_GRID_POINTS 2
 
-
   #else  // !AUTO_BED_LEVELING_GRID
 
       // Arbitrary points to probe. A simple cross-product
@@ -444,11 +444,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #endif // AUTO_BED_LEVELING_GRID
 
-
   // Offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
-  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // -left  +right
+  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // Probe on: -left  +right
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // -front +behind
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Probe on: -front +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // -below (always!)
 
   #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
@@ -460,6 +459,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
   #define Z_RAISE_AFTER_PROBING 15    //How much the extruder will be raised after the last probing point.
 
+//   #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
+                                                                            //Useful to retract a deployable probe.
+                                                                           
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
@@ -496,10 +498,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 // Manual homing switch locations:
 // For deltabots this means top and center of the Cartesian print volume.
+#ifdef MANUAL_HOME_POSITIONS
   #define MANUAL_X_HOME_POS 0
   #define MANUAL_Y_HOME_POS 0
   #define MANUAL_Z_HOME_POS 0
   //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
+#endif
 
 //// MOVEMENT SETTINGS
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
@@ -536,8 +540,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #ifdef CUSTOM_M_CODES
   #ifdef ENABLE_AUTO_BED_LEVELING
     #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-    #define Z_PROBE_OFFSET_RANGE_MIN -15
+    #define Z_PROBE_OFFSET_RANGE_MIN -20
-    #define Z_PROBE_OFFSET_RANGE_MAX -5
+    #define Z_PROBE_OFFSET_RANGE_MAX 20
   #endif
 #endif
 
@@ -565,13 +569,16 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //==============================LCD and SD support=============================
 
 // Define your display language below. Replace (en) with your language code and uncomment.
-// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
+// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
 // See also language.h
 //#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Character based displays can have different extended charsets.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
-#define DISPLAY_CHARSET_HD44780_JAPAN     // "ääööüüß23°"
+// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
-//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
+// See also documentation/LCDLanguageFont.md
+  #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
+  //#define DISPLAY_CHARSET_HD44780_WESTERN
+  //#define DISPLAY_CHARSET_HD44780_CYRILLIC
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
@@ -584,6 +591,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+                                               // 0 to disable buzzer feedback  
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -646,7 +654,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define FAST_PWM_FAN
 
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
-// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
 //#define FAN_SOFT_PWM
 

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -32,7 +32,7 @@
 
 //automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
 //The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
+//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
 // the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
 // you exit the value by any M109 without F*
 // Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
@@ -100,6 +100,30 @@
 // On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
 //#define Z_DUAL_STEPPER_DRIVERS
 
+#ifdef Z_DUAL_STEPPER_DRIVERS
+
+  // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+  // That way the machine is capable to align the bed during home, since both Z steppers are homed. 
+  // There is also an implementation of M666 (software endstops adjustment) to this feature.
+  // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+  // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+  // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+  // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+  // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+  #define Z_DUAL_ENDSTOPS
+
+  #ifdef Z_DUAL_ENDSTOPS
+    #define Z2_STEP_PIN E2_STEP_PIN           // Stepper to be used to Z2 axis.
+    #define Z2_DIR_PIN E2_DIR_PIN
+    #define Z2_ENABLE_PIN E2_ENABLE_PIN
+    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
+    const bool Z2_MAX_ENDSTOP_INVERTING = false;
+    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+  #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
 // Same again but for Y Axis.
 //#define Y_DUAL_STEPPER_DRIVERS
 
@@ -159,8 +183,6 @@
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}
 
-#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
-
 //By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
 #define INVERT_X_STEP_PIN false
 #define INVERT_Y_STEP_PIN false
@@ -205,7 +227,6 @@
 // Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
 #define DIGIPOT_I2C_NUM_CHANNELS 4
 // actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
-//#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}
 #define DIGIPOT_I2C_MOTOR_CURRENTS {1.7, 1.7, 1.7, 1.7}
 
 //===========================================================================
@@ -213,13 +234,21 @@
 //===========================================================================
 
 #define ENCODER_RATE_MULTIPLIER         // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
-#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value
+#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
-#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
 //#define ENCODER_RATE_MULTIPLIER_DEBUG  // If defined, output the encoder steps per second value
 
 //#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
 
+#ifdef SDSUPPORT
+
+  // If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+  // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+  // in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+  // be commented out otherwise
+  //#define SDCARDDETECTINVERTED
+
   #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
@@ -228,20 +257,22 @@
   // using:
   //#define MENU_ADDAUTOSTART
 
-// Show a progress bar on the LCD when printing from SD
+  // Show a progress bar on HD44780 LCDs for SD printing
   //#define LCD_PROGRESS_BAR
 
   #ifdef LCD_PROGRESS_BAR
     // Amount of time (ms) to show the bar
     #define PROGRESS_BAR_BAR_TIME 2000
     // Amount of time (ms) to show the status message
-  #define PROGRESS_BAR_MSG_TIME 2000
+    #define PROGRESS_BAR_MSG_TIME 3000
     // Amount of time (ms) to retain the status message (0=forever)
     #define PROGRESS_MSG_EXPIRE   0
     // Enable this to show messages for MSG_TIME then hide them
     //#define PROGRESS_MSG_ONCE
   #endif
 
+#endif // SDSUPPORT
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -278,7 +309,7 @@
   #define EXTRUDER_ADVANCE_K .0
   #define D_FILAMENT 2.85
   #define STEPS_MM_E 836
-#endif // ADVANCE
+#endif
 
 // Arc interpretation settings:
 #define MM_PER_ARC_SEGMENT 1
@@ -286,12 +317,6 @@
 
 const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
-// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
-// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
-// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
-// be commented out otherwise
-//#define SDCARDDETECTINVERTED
-
 // Control heater 0 and heater 1 in parallel.
 //#define HEATERS_PARALLEL
 
@@ -301,7 +326,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 
 // The number of linear motions that can be in the plan at any give time.
 // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
-#if defined SDSUPPORT
+#ifdef SDSUPPORT
   #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
   #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
@@ -323,9 +348,11 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 #ifdef FWRETRACT
   #define MIN_RETRACT 0.1                //minimum extruded mm to accept a automatic gcode retraction attempt
   #define RETRACT_LENGTH 3               //default retract length (positive mm)
+  #define RETRACT_LENGTH_SWAP 13         //default swap retract length (positive mm), for extruder change
   #define RETRACT_FEEDRATE 45            //default feedrate for retracting (mm/s)
   #define RETRACT_ZLIFT 0                //default retract Z-lift
   #define RETRACT_RECOVER_LENGTH 0       //default additional recover length (mm, added to retract length when recovering)
+  #define RETRACT_RECOVER_LENGTH_SWAP 0  //default additional swap recover length (mm, added to retract length when recovering from extruder change)
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
@@ -341,6 +368,139 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #endif
 #endif
 
+/******************************************************************************\
+ * enable this section if you have TMC26X motor drivers. 
+ * you need to import the TMC26XStepper library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_TMCDRIVER
+#ifdef HAVE_TMCDRIVER
+
+//	#define X_IS_TMC
+	#define X_MAX_CURRENT 1000  //in mA
+	#define X_SENSE_RESISTOR 91 //in mOhms
+	#define X_MICROSTEPS 16     //number of microsteps
+	
+//	#define X2_IS_TMC
+	#define X2_MAX_CURRENT 1000  //in mA
+	#define X2_SENSE_RESISTOR 91 //in mOhms
+	#define X2_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y_IS_TMC
+	#define Y_MAX_CURRENT 1000  //in mA
+	#define Y_SENSE_RESISTOR 91 //in mOhms
+	#define Y_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y2_IS_TMC
+	#define Y2_MAX_CURRENT 1000  //in mA
+	#define Y2_SENSE_RESISTOR 91 //in mOhms
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define Z_IS_TMC
+	#define Z_MAX_CURRENT 1000  //in mA
+	#define Z_SENSE_RESISTOR 91 //in mOhms
+	#define Z_MICROSTEPS 16     //number of microsteps
+	
+//	#define Z2_IS_TMC
+	#define Z2_MAX_CURRENT 1000  //in mA
+	#define Z2_SENSE_RESISTOR 91 //in mOhms
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	
+//	#define E0_IS_TMC
+	#define E0_MAX_CURRENT 1000  //in mA
+	#define E0_SENSE_RESISTOR 91 //in mOhms
+	#define E0_MICROSTEPS 16     //number of microsteps
+	
+//	#define E1_IS_TMC
+	#define E1_MAX_CURRENT 1000  //in mA
+	#define E1_SENSE_RESISTOR 91 //in mOhms
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E2_IS_TMC
+	#define E2_MAX_CURRENT 1000  //in mA
+	#define E2_SENSE_RESISTOR 91 //in mOhms
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E3_IS_TMC
+	#define E3_MAX_CURRENT 1000  //in mA
+	#define E3_SENSE_RESISTOR 91 //in mOhms
+	#define E3_MICROSTEPS 16     //number of microsteps		
+
+#endif
+
+/******************************************************************************\
+ * enable this section if you have L6470  motor drivers. 
+ * you need to import the L6470 library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_L6470DRIVER
+#ifdef HAVE_L6470DRIVER
+
+//	#define X_IS_L6470
+	#define X_MICROSTEPS 16     //number of microsteps
+	#define X_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define X2_IS_L6470
+	#define X2_MICROSTEPS 16     //number of microsteps
+	#define X2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y_IS_L6470
+	#define Y_MICROSTEPS 16     //number of microsteps
+	#define Y_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y2_IS_L6470
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	#define Y2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall	
+	
+//	#define Z_IS_L6470
+	#define Z_MICROSTEPS 16     //number of microsteps
+	#define Z_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Z2_IS_L6470
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	#define Z2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E0_IS_L6470
+	#define E0_MICROSTEPS 16     //number of microsteps
+	#define E0_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E0_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E1_IS_L6470
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	#define E1_MICROSTEPS 16     //number of microsteps
+	#define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E2_IS_L6470
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	#define E2_MICROSTEPS 16     //number of microsteps
+	#define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E3_IS_L6470
+	#define E3_MICROSTEPS 16     //number of microsteps		
+	#define E3_MICROSTEPS 16     //number of microsteps
+	#define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+#endif
+
 #include "Conditionals.h"
 #include "SanityCheck.h"
 

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -320,7 +320,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
   // #define ENDSTOPPULLUP_ZMIN
 #endif
 
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
@@ -343,13 +343,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DISABLE_E false // For all extruders
 #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
-#define INVERT_X_DIR false    // for Mendel set to false, for Orca set to true
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_Y_DIR true     // for Mendel set to true, for Orca set to false
+#define INVERT_X_DIR false
-#define INVERT_Z_DIR false    // for Mendel set to false, for Orca set to true
+#define INVERT_Y_DIR false
-#define INVERT_E0_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_Z_DIR true
-#define INVERT_E1_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E0_DIR false
-#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E1_DIR false
-#define INVERT_E3_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false
+#define INVERT_E2_DIR false
+#define INVERT_E3_DIR false
 
 // ENDSTOP SETTINGS:
 // Sets direction of endstops when homing; 1=MAX, -1=MIN
@@ -361,12 +362,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
 
 // Travel limits after homing (units are in mm)
-#define X_MAX_POS 205
 #define X_MIN_POS 0
-#define Y_MAX_POS 205
 #define Y_MIN_POS 0
-#define Z_MAX_POS 120
 #define Z_MIN_POS 0
+#define X_MAX_POS 205
+#define Y_MAX_POS 205
+#define Z_MAX_POS 120
 
 //===========================================================================
 //============================= Filament Runout Sensor ======================
@@ -432,7 +433,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
     // You probably don't need more than 3 (squared=9)
     #define AUTO_BED_LEVELING_GRID_POINTS 2
 
-
   #else  // !AUTO_BED_LEVELING_GRID
 
       // Arbitrary points to probe. A simple cross-product
@@ -446,11 +446,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
   #endif // AUTO_BED_LEVELING_GRID
 
-
   // Offsets to the probe relative to the extruder tip (Hotend - Probe)
   // X and Y offsets must be integers
-  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // -left  +right
+  #define X_PROBE_OFFSET_FROM_EXTRUDER -25     // Probe on: -left  +right
-  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // -front +behind
+  #define Y_PROBE_OFFSET_FROM_EXTRUDER -29     // Probe on: -front +behind
   #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35  // -below (always!)
 
   #define Z_RAISE_BEFORE_HOMING 4       // (in mm) Raise Z before homing (G28) for Probe Clearance.
@@ -462,6 +461,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
   #define Z_RAISE_AFTER_PROBING 15    //How much the extruder will be raised after the last probing point.
 
+//   #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
+                                                                            //Useful to retract a deployable probe.
+                                                                           
   //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
   //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
@@ -498,10 +500,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 
 // Manual homing switch locations:
 // For deltabots this means top and center of the Cartesian print volume.
+#ifdef MANUAL_HOME_POSITIONS
   #define MANUAL_X_HOME_POS 0
   #define MANUAL_Y_HOME_POS 0
   #define MANUAL_Z_HOME_POS 0
   //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
+#endif
 
 //// MOVEMENT SETTINGS
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
@@ -521,7 +525,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DEFAULT_RETRACT_ACCELERATION  3000   // E acceleration in mm/s^2 for retracts
 #define DEFAULT_TRAVEL_ACCELERATION   500    // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
 
-
 // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
 // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
 // For the other hotends it is their distance from the extruder 0 hotend.
@@ -543,8 +546,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #ifdef CUSTOM_M_CODES
   #ifdef ENABLE_AUTO_BED_LEVELING
     #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
-    #define Z_PROBE_OFFSET_RANGE_MIN -15
+    #define Z_PROBE_OFFSET_RANGE_MIN -20
-    #define Z_PROBE_OFFSET_RANGE_MAX -5
+    #define Z_PROBE_OFFSET_RANGE_MAX 20
   #endif
 #endif
 
@@ -572,13 +575,16 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //==============================LCD and SD support=============================
 
 // Define your display language below. Replace (en) with your language code and uncomment.
-// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
+// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, test
 // See also language.h
 //#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
 
-// Character based displays can have different extended charsets.
+// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display.
-#define DISPLAY_CHARSET_HD44780_JAPAN     // "ääööüüß23°"
+// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset.
-//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
+// See also documentation/LCDLanguageFont.md
+  #define DISPLAY_CHARSET_HD44780_JAPAN        // this is the most common hardware
+  //#define DISPLAY_CHARSET_HD44780_WESTERN
+  //#define DISPLAY_CHARSET_HD44780_CYRILLIC
 
 //#define ULTRA_LCD  //general LCD support, also 16x2
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
@@ -591,6 +597,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define ULTIPANEL  //the UltiPanel as on Thingiverse
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000	// this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
+                                               // 0 to disable buzzer feedback  
 
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
 // http://reprap.org/wiki/PanelOne
@@ -653,7 +660,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define FAST_PWM_FAN
 
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
-// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
 //#define FAN_SOFT_PWM
 

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -100,6 +100,30 @@
 // On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
 //#define Z_DUAL_STEPPER_DRIVERS
 
+#ifdef Z_DUAL_STEPPER_DRIVERS
+
+  // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+  // That way the machine is capable to align the bed during home, since both Z steppers are homed. 
+  // There is also an implementation of M666 (software endstops adjustment) to this feature.
+  // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+  // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+  // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+  // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+  // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+  #define Z_DUAL_ENDSTOPS
+
+  #ifdef Z_DUAL_ENDSTOPS
+    #define Z2_STEP_PIN E2_STEP_PIN           // Stepper to be used to Z2 axis.
+    #define Z2_DIR_PIN E2_DIR_PIN
+    #define Z2_ENABLE_PIN E2_ENABLE_PIN
+    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
+    const bool Z2_MAX_ENDSTOP_INVERTING = false;
+    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+  #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
 // Same again but for Y Axis.
 //#define Y_DUAL_STEPPER_DRIVERS
 
@@ -158,11 +182,7 @@
 //#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}
-#ifdef CONFIG_STEPPERS_TOSHIBA
+
-#define MAX_STEP_FREQUENCY 10000 // Max step frequency for Toshiba Stepper Controllers
-#else
-#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
-#endif
 //By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
 #define INVERT_X_STEP_PIN false
 #define INVERT_Y_STEP_PIN false
@@ -214,13 +234,21 @@
 //===========================================================================
 
 #define ENCODER_RATE_MULTIPLIER         // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
-#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value
+#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
-#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
 //#define ENCODER_RATE_MULTIPLIER_DEBUG  // If defined, output the encoder steps per second value
 
 //#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
 
+#ifdef SDSUPPORT
+
+  // If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+  // You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+  // in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
+  // be commented out otherwise
+  #define SDCARDDETECTINVERTED
+
   #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
@@ -229,7 +257,7 @@
   // using:
   //#define MENU_ADDAUTOSTART
 
-// Show a progress bar on the LCD when printing from SD?
+  // Show a progress bar on HD44780 LCDs for SD printing
   //#define LCD_PROGRESS_BAR
 
   #ifdef LCD_PROGRESS_BAR
@@ -243,6 +271,8 @@
     //#define PROGRESS_MSG_ONCE
   #endif
 
+#endif // SDSUPPORT
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -277,13 +307,9 @@
 
 #ifdef ADVANCE
   #define EXTRUDER_ADVANCE_K .0
-
   #define D_FILAMENT 2.85
   #define STEPS_MM_E 836
-  #define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
+#endif
-  #define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)
-
-#endif // ADVANCE
 
 // Arc interpretation settings:
 #define MM_PER_ARC_SEGMENT 1
@@ -291,12 +317,6 @@
 
 const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
-// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
-// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
-// in the pins.h file.  When using a push button pulling the pin to ground this will need inverted.  This setting should
-// be commented out otherwise
-#define SDCARDDETECTINVERTED
-
 // Control heater 0 and heater 1 in parallel.
 //#define HEATERS_PARALLEL
 
@@ -306,7 +326,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 
 // The number of linear motions that can be in the plan at any give time.
 // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
-#if defined SDSUPPORT
+#ifdef SDSUPPORT
   #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
   #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
@@ -348,6 +368,139 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #endif
 #endif
 
+/******************************************************************************\
+ * enable this section if you have TMC26X motor drivers. 
+ * you need to import the TMC26XStepper library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_TMCDRIVER
+#ifdef HAVE_TMCDRIVER
+
+//	#define X_IS_TMC
+	#define X_MAX_CURRENT 1000  //in mA
+	#define X_SENSE_RESISTOR 91 //in mOhms
+	#define X_MICROSTEPS 16     //number of microsteps
+	
+//	#define X2_IS_TMC
+	#define X2_MAX_CURRENT 1000  //in mA
+	#define X2_SENSE_RESISTOR 91 //in mOhms
+	#define X2_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y_IS_TMC
+	#define Y_MAX_CURRENT 1000  //in mA
+	#define Y_SENSE_RESISTOR 91 //in mOhms
+	#define Y_MICROSTEPS 16     //number of microsteps
+	
+//	#define Y2_IS_TMC
+	#define Y2_MAX_CURRENT 1000  //in mA
+	#define Y2_SENSE_RESISTOR 91 //in mOhms
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define Z_IS_TMC
+	#define Z_MAX_CURRENT 1000  //in mA
+	#define Z_SENSE_RESISTOR 91 //in mOhms
+	#define Z_MICROSTEPS 16     //number of microsteps
+	
+//	#define Z2_IS_TMC
+	#define Z2_MAX_CURRENT 1000  //in mA
+	#define Z2_SENSE_RESISTOR 91 //in mOhms
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	
+//	#define E0_IS_TMC
+	#define E0_MAX_CURRENT 1000  //in mA
+	#define E0_SENSE_RESISTOR 91 //in mOhms
+	#define E0_MICROSTEPS 16     //number of microsteps
+	
+//	#define E1_IS_TMC
+	#define E1_MAX_CURRENT 1000  //in mA
+	#define E1_SENSE_RESISTOR 91 //in mOhms
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E2_IS_TMC
+	#define E2_MAX_CURRENT 1000  //in mA
+	#define E2_SENSE_RESISTOR 91 //in mOhms
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	
+//	#define E3_IS_TMC
+	#define E3_MAX_CURRENT 1000  //in mA
+	#define E3_SENSE_RESISTOR 91 //in mOhms
+	#define E3_MICROSTEPS 16     //number of microsteps		
+
+#endif
+
+/******************************************************************************\
+ * enable this section if you have L6470  motor drivers. 
+ * you need to import the L6470 library into the arduino IDE for this
+ ******************************************************************************/
+
+//#define HAVE_L6470DRIVER
+#ifdef HAVE_L6470DRIVER
+
+//	#define X_IS_L6470
+	#define X_MICROSTEPS 16     //number of microsteps
+	#define X_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define X2_IS_L6470
+	#define X2_MICROSTEPS 16     //number of microsteps
+	#define X2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define X2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y_IS_L6470
+	#define Y_MICROSTEPS 16     //number of microsteps
+	#define Y_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Y2_IS_L6470
+	#define Y2_MICROSTEPS 16     //number of microsteps	
+	#define Y2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Y2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall	
+	
+//	#define Z_IS_L6470
+	#define Z_MICROSTEPS 16     //number of microsteps
+	#define Z_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define Z2_IS_L6470
+	#define Z2_MICROSTEPS 16     //number of microsteps
+	#define Z2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define Z2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E0_IS_L6470
+	#define E0_MICROSTEPS 16     //number of microsteps
+	#define E0_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E0_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E1_IS_L6470
+	#define E1_MICROSTEPS 16     //number of microsteps	
+	#define E1_MICROSTEPS 16     //number of microsteps
+	#define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E2_IS_L6470
+	#define E2_MICROSTEPS 16     //number of microsteps	
+	#define E2_MICROSTEPS 16     //number of microsteps
+	#define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+//	#define E3_IS_L6470
+	#define E3_MICROSTEPS 16     //number of microsteps		
+	#define E3_MICROSTEPS 16     //number of microsteps
+	#define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be carefull not to go too high    
+	#define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+	#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+	
+#endif
+
 #include "Conditionals.h"
 #include "SanityCheck.h"
 

Marlin/stepper.cpp

@@ -388,7 +388,9 @@ ISR(TIMER1_COMPA_vect) {
   {
     current_block = NULL;
     plan_discard_current_block();
+    #ifdef SD_FINISHED_RELEASECOMMAND
       if ((cleaning_buffer_counter == 1) && (SD_FINISHED_STEPPERRELEASE)) enquecommands_P(PSTR(SD_FINISHED_RELEASECOMMAND));
+    #endif
     cleaning_buffer_counter--;
     OCR1A = 200;
     return;