Merge pull request #7308 from thinkyhead/bf_cleanup_config_adv

Fixes for FWRETRACT
This commit is contained in:
Scott Lahteine 2017-07-29 21:20:19 -05:00 committed by GitHub
commit 29eef360d0
36 changed files with 306 additions and 203 deletions

View file

@ -76,7 +76,8 @@ script:
- build_marlin - build_marlin
# #
# Test 2 extruders (one MAX6675) and heated bed on basic RAMPS 1.4 # Test 2 extruders (one MAX6675) and heated bed on basic RAMPS 1.4
# plus a "Fix Mounted" Probe with Safe Homing and some arc options # Test a "Fix Mounted" Probe with Safe Homing, some arc options,
# linear bed leveling, M48, leveling debug, and firmware retraction.
# #
- opt_set MOTHERBOARD BOARD_RAMPS_14_EEB - opt_set MOTHERBOARD BOARD_RAMPS_14_EEB
- opt_set EXTRUDERS 2 - opt_set EXTRUDERS 2
@ -84,12 +85,10 @@ script:
- opt_set TEMP_SENSOR_1 1 - opt_set TEMP_SENSOR_1 1
- opt_set TEMP_SENSOR_BED 1 - opt_set TEMP_SENSOR_BED 1
- opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING ARC_P_CIRCLES CNC_WORKSPACE_PLANES - opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING ARC_P_CIRCLES CNC_WORKSPACE_PLANES
- opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER SDSUPPORT EEPROM_SETTINGS
- opt_enable BLINKM PCA9632 RGB_LED NEOPIXEL_RGBW_LED - opt_enable BLINKM PCA9632 RGB_LED NEOPIXEL_RGBW_LED
- build_marlin
#
# ...with AUTO_BED_LEVELING_LINEAR, Z_MIN_PROBE_REPEATABILITY_TEST, and DEBUG_LEVELING_FEATURE
#
- opt_enable AUTO_BED_LEVELING_LINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE - opt_enable AUTO_BED_LEVELING_LINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE
- opt_enable_adv FWRETRACT
- opt_set ABL_GRID_POINTS_X 16 - opt_set ABL_GRID_POINTS_X 16
- opt_set ABL_GRID_POINTS_Y 16 - opt_set ABL_GRID_POINTS_Y 16
- build_marlin - build_marlin

View file

@ -189,6 +189,13 @@
#define DEFAULT_KEEPALIVE_INTERVAL 2 #define DEFAULT_KEEPALIVE_INTERVAL 2
#endif #endif
/**
* Provide a MAX_AUTORETRACT for older configs
*/
#if ENABLED(FWRETRACT) && !defined(MAX_AUTORETRACT)
#define MAX_AUTORETRACT 99
#endif
/** /**
* MAX_STEP_FREQUENCY differs for TOSHIBA * MAX_STEP_FREQUENCY differs for TOSHIBA
*/ */

View file

@ -764,7 +764,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -774,7 +774,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -383,10 +383,15 @@ extern float soft_endstop_min[XYZ], soft_endstop_max[XYZ];
#endif #endif
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
extern bool autoretract_enabled; extern bool autoretract_enabled; // M209 S - Autoretract switch
extern bool retracted[EXTRUDERS]; // extruder[n].retracted extern float retract_length, // M207 S - G10 Retract length
extern float retract_length, retract_length_swap, retract_feedrate_mm_s, retract_zlift; retract_feedrate_mm_s, // M207 F - G10 Retract feedrate
extern float retract_recover_length, retract_recover_length_swap, retract_recover_feedrate_mm_s; retract_zlift, // M207 Z - G10 Retract hop size
retract_recover_length, // M208 S - G11 Recover length
retract_recover_feedrate_mm_s, // M208 F - G11 Recover feedrate
swap_retract_length, // M207 W - G10 Swap Retract length
swap_retract_recover_length, // M208 W - G11 Swap Recover length
swap_retract_recover_feedrate_mm_s; // M208 R - G11 Swap Recover feedrate
#endif #endif
// Print job timer // Print job timer

View file

@ -557,20 +557,22 @@ static uint8_t target_extruder;
baricuda_e_to_p_pressure = 0; baricuda_e_to_p_pressure = 0;
#endif #endif
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT) // Initialized by settings.load()...
bool autoretract_enabled, // M209 S - Autoretract switch
bool autoretract_enabled = false; retracted[EXTRUDERS] = { false }; // Which extruders are currently retracted
bool retracted[EXTRUDERS] = { false }; float retract_length, // M207 S - G10 Retract length
bool retracted_swap[EXTRUDERS] = { false }; retract_feedrate_mm_s, // M207 F - G10 Retract feedrate
retract_zlift, // M207 Z - G10 Retract hop size
float retract_length = RETRACT_LENGTH; retract_recover_length, // M208 S - G11 Recover length
float retract_length_swap = RETRACT_LENGTH_SWAP; retract_recover_feedrate_mm_s, // M208 F - G11 Recover feedrate
float retract_feedrate_mm_s = RETRACT_FEEDRATE; swap_retract_length, // M207 W - G10 Swap Retract length
float retract_zlift = RETRACT_ZLIFT; swap_retract_recover_length, // M208 W - G11 Swap Recover length
float retract_recover_length = RETRACT_RECOVER_LENGTH; swap_retract_recover_feedrate_mm_s; // M208 R - G11 Swap Recover feedrate
float retract_recover_length_swap = RETRACT_RECOVER_LENGTH_SWAP; #if EXTRUDERS > 1
float retract_recover_feedrate_mm_s = RETRACT_RECOVER_FEEDRATE; bool retracted_swap[EXTRUDERS] = { false }; // Which extruders are swap-retracted
#else
constexpr bool retracted_swap[1] = { false };
#endif
#endif // FWRETRACT #endif // FWRETRACT
#if HAS_POWER_SWITCH #if HAS_POWER_SWITCH
@ -3100,55 +3102,126 @@ static void homeaxis(const AxisEnum axis) {
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
void retract(const bool retracting, const bool swapping = false) { /**
* Retract or recover according to firmware settings
*
* This function handles retract/recover moves for G10 and G11,
* plus auto-retract moves sent from G0/G1 when E-only moves are done.
*
* To simplify the logic, doubled retract/recover moves are ignored.
*
* Note: Z lift is done transparently to the planner. Aborting
* a print between G10 and G11 may corrupt the Z position.
*
* Note: Auto-retract will apply the set Z hop in addition to any Z hop
* included in the G-code. Use M207 Z0 to to prevent double hop.
*/
void retract(const bool retracting
#if EXTRUDERS > 1
, bool swapping = false
#endif
) {
static float hop_height; static float hop_height, // Remember where the Z height started
hop_amount = 0.0; // Total amount lifted, for use in recover
if (retracting == retracted[active_extruder]) return; // Simply never allow two retracts or recovers in a row
if (retracted[active_extruder] == retracting) return;
#if EXTRUDERS < 2
bool swapping = false;
#endif
if (!retracting) swapping = retracted_swap[active_extruder];
/* // debugging
SERIAL_ECHOLNPAIR("retracting ", retracting);
SERIAL_ECHOLNPAIR("swapping ", swapping);
SERIAL_ECHOLNPAIR("active extruder ", active_extruder);
for (uint8_t i = 0; i < EXTRUDERS; ++i) {
SERIAL_ECHOPAIR("retracted[", i);
SERIAL_ECHOLNPAIR("] ", retracted[i]);
SERIAL_ECHOPAIR("retracted_swap[", i);
SERIAL_ECHOLNPAIR("] ", retracted_swap[i]);
}
SERIAL_ECHOLNPAIR("current_position[z] ", current_position[Z_AXIS]);
SERIAL_ECHOLNPAIR("hop_amount ", hop_amount);
//*/
const bool has_zhop = retract_zlift > 0.01; // Is there a hop set?
const float old_feedrate_mm_s = feedrate_mm_s; const float old_feedrate_mm_s = feedrate_mm_s;
const int16_t old_flow = flow_percentage[active_extruder];
// Don't apply flow multiplication to retract/recover
flow_percentage[active_extruder] = 100;
// The current position will be the destination for E and Z moves
set_destination_to_current(); set_destination_to_current();
if (retracting) { if (retracting) {
// Remember the Z height since G-code may include its own Z-hop
// For best results turn off Z hop if G-code already includes it
hop_height = destination[Z_AXIS];
// Retract by moving from a faux E position back to the current E position
feedrate_mm_s = retract_feedrate_mm_s; feedrate_mm_s = retract_feedrate_mm_s;
current_position[E_AXIS] += (swapping ? retract_length_swap : retract_length) / volumetric_multiplier[active_extruder]; current_position[E_AXIS] += (swapping ? swap_retract_length : retract_length) / volumetric_multiplier[active_extruder];
sync_plan_position_e(); sync_plan_position_e();
prepare_move_to_destination(); prepare_move_to_destination();
if (retract_zlift > 0.01) { // Is a Z hop set, and has the hop not yet been done?
hop_height = current_position[Z_AXIS]; if (has_zhop) {
// Pretend current position is lower hop_amount += retract_zlift; // Carriage is raised for retraction hop
current_position[Z_AXIS] -= retract_zlift; current_position[Z_AXIS] -= retract_zlift; // Pretend current pos is lower. Next move raises Z.
SYNC_PLAN_POSITION_KINEMATIC(); SYNC_PLAN_POSITION_KINEMATIC(); // Set the planner to the new position
// Raise up to the old current_position prepare_move_to_destination(); // Raise up to the old current pos
prepare_move_to_destination();
} }
} }
else { else {
// If a hop was done and Z hasn't changed, undo the Z hop
// If the height hasn't been lowered, undo the Z hop if (hop_amount && NEAR(hop_height, destination[Z_AXIS])) {
if (retract_zlift > 0.01 && hop_height <= current_position[Z_AXIS]) { current_position[Z_AXIS] += hop_amount; // Pretend current pos is higher. Next move lowers Z.
// Pretend current position is higher. Z will lower on the next move SYNC_PLAN_POSITION_KINEMATIC(); // Set the planner to the new position
current_position[Z_AXIS] += retract_zlift; prepare_move_to_destination(); // Lower to the old current pos
SYNC_PLAN_POSITION_KINEMATIC(); hop_amount = 0.0;
// Lower Z
prepare_move_to_destination();
} }
feedrate_mm_s = retract_recover_feedrate_mm_s; // A retract multiplier has been added here to get faster swap recovery
const float move_e = swapping ? retract_length_swap + retract_recover_length_swap : retract_length + retract_recover_length; feedrate_mm_s = swapping ? swap_retract_recover_feedrate_mm_s : retract_recover_feedrate_mm_s;
const float move_e = swapping ? swap_retract_length + swap_retract_recover_length : retract_length + retract_recover_length;
current_position[E_AXIS] -= move_e / volumetric_multiplier[active_extruder]; current_position[E_AXIS] -= move_e / volumetric_multiplier[active_extruder];
sync_plan_position_e(); sync_plan_position_e();
// Recover E prepare_move_to_destination(); // Recover E
prepare_move_to_destination();
} }
// Restore flow and feedrate
flow_percentage[active_extruder] = old_flow;
feedrate_mm_s = old_feedrate_mm_s; feedrate_mm_s = old_feedrate_mm_s;
// The active extruder is now retracted or recovered
retracted[active_extruder] = retracting; retracted[active_extruder] = retracting;
// If swap retract/recover then update the retracted_swap flag too
#if EXTRUDERS > 1
if (swapping) retracted_swap[active_extruder] = retracting;
#endif
/* // debugging
SERIAL_ECHOLNPAIR("retracting ", retracting);
SERIAL_ECHOLNPAIR("swapping ", swapping);
SERIAL_ECHOLNPAIR("active_extruder ", active_extruder);
for (uint8_t i = 0; i < EXTRUDERS; ++i) {
SERIAL_ECHOPAIR("retracted[", i);
SERIAL_ECHOLNPAIR("] ", retracted[i]);
SERIAL_ECHOPAIR("retracted_swap[", i);
SERIAL_ECHOLNPAIR("] ", retracted_swap[i]);
}
SERIAL_ECHOLNPAIR("current_position[z] ", current_position[Z_AXIS]);
SERIAL_ECHOLNPAIR("hop_amount ", hop_amount);
//*/
} // retract() } // retract()
#endif // FWRETRACT #endif // FWRETRACT
@ -3277,18 +3350,18 @@ inline void gcode_G0_G1(
gcode_get_destination(); // For X Y Z E F gcode_get_destination(); // For X Y Z E F
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
if (MIN_AUTORETRACT <= MAX_AUTORETRACT) {
if (autoretract_enabled && !(parser.seen('X') || parser.seen('Y') || parser.seen('Z')) && parser.seen('E')) { // When M209 Autoretract is enabled, convert E-only moves to firmware retract/recover moves
if (autoretract_enabled && parser.seen('E') && !(parser.seen('X') || parser.seen('Y') || parser.seen('Z'))) {
const float echange = destination[E_AXIS] - current_position[E_AXIS]; const float echange = destination[E_AXIS] - current_position[E_AXIS];
// Is this move an attempt to retract or recover? // Is this a retract or recover move?
if ((echange < -(MIN_RETRACT) && !retracted[active_extruder]) || (echange > MIN_RETRACT && retracted[active_extruder])) { if (WITHIN(FABS(echange), MIN_AUTORETRACT, MAX_AUTORETRACT) && retracted[active_extruder] == (echange > 0.0)) {
current_position[E_AXIS] = destination[E_AXIS]; // hide the slicer-generated retract/recover from calculations current_position[E_AXIS] = destination[E_AXIS]; // Hide a G1-based retract/recover from calculations
sync_plan_position_e(); // AND from the planner sync_plan_position_e(); // AND from the planner
retract(!retracted[active_extruder]); return retract(echange < 0.0); // Firmware-based retract/recover (double-retract ignored)
return; }
} }
} }
#endif // FWRETRACT #endif // FWRETRACT
#if IS_SCARA #if IS_SCARA
@ -8486,7 +8559,7 @@ inline void gcode_M205() {
* M207: Set firmware retraction values * M207: Set firmware retraction values
* *
* S[+units] retract_length * S[+units] retract_length
* W[+units] retract_length_swap (multi-extruder) * W[+units] swap_retract_length (multi-extruder)
* F[units/min] retract_feedrate_mm_s * F[units/min] retract_feedrate_mm_s
* Z[units] retract_zlift * Z[units] retract_zlift
*/ */
@ -8494,24 +8567,22 @@ inline void gcode_M205() {
if (parser.seen('S')) retract_length = parser.value_axis_units(E_AXIS); if (parser.seen('S')) retract_length = parser.value_axis_units(E_AXIS);
if (parser.seen('F')) retract_feedrate_mm_s = MMM_TO_MMS(parser.value_axis_units(E_AXIS)); if (parser.seen('F')) retract_feedrate_mm_s = MMM_TO_MMS(parser.value_axis_units(E_AXIS));
if (parser.seen('Z')) retract_zlift = parser.value_linear_units(); if (parser.seen('Z')) retract_zlift = parser.value_linear_units();
#if EXTRUDERS > 1 if (parser.seen('W')) swap_retract_length = parser.value_axis_units(E_AXIS);
if (parser.seen('W')) retract_length_swap = parser.value_axis_units(E_AXIS);
#endif
} }
/** /**
* M208: Set firmware un-retraction values * M208: Set firmware un-retraction values
* *
* S[+units] retract_recover_length (in addition to M207 S*) * S[+units] retract_recover_length (in addition to M207 S*)
* W[+units] retract_recover_length_swap (multi-extruder) * W[+units] swap_retract_recover_length (multi-extruder)
* F[units/min] retract_recover_feedrate_mm_s * F[units/min] retract_recover_feedrate_mm_s
* R[units/min] swap_retract_recover_feedrate_mm_s
*/ */
inline void gcode_M208() { inline void gcode_M208() {
if (parser.seen('S')) retract_recover_length = parser.value_axis_units(E_AXIS); if (parser.seen('S')) retract_recover_length = parser.value_axis_units(E_AXIS);
if (parser.seen('F')) retract_recover_feedrate_mm_s = MMM_TO_MMS(parser.value_axis_units(E_AXIS)); if (parser.seen('F')) retract_recover_feedrate_mm_s = MMM_TO_MMS(parser.value_axis_units(E_AXIS));
#if EXTRUDERS > 1 if (parser.seen('R')) swap_retract_recover_feedrate_mm_s = MMM_TO_MMS(parser.value_axis_units(E_AXIS));
if (parser.seen('W')) retract_recover_length_swap = parser.value_axis_units(E_AXIS); if (parser.seen('W')) swap_retract_recover_length = parser.value_axis_units(E_AXIS);
#endif
} }
/** /**
@ -8520,9 +8591,11 @@ inline void gcode_M205() {
* moves will be classified as retraction. * moves will be classified as retraction.
*/ */
inline void gcode_M209() { inline void gcode_M209() {
if (MIN_AUTORETRACT <= MAX_AUTORETRACT) {
if (parser.seen('S')) { if (parser.seen('S')) {
autoretract_enabled = parser.value_bool(); autoretract_enabled = parser.value_bool();
for (int i = 0; i < EXTRUDERS; i++) retracted[i] = false; for (uint8_t i = 0; i < EXTRUDERS; i++) retracted[i] = false;
}
} }
} }
@ -10987,7 +11060,7 @@ void process_next_command() {
gcode_M208(); gcode_M208();
break; break;
case 209: // M209: Turn Automatic Retract Detection on/off case 209: // M209: Turn Automatic Retract Detection on/off
gcode_M209(); if (MIN_AUTORETRACT <= MAX_AUTORETRACT) gcode_M209();
break; break;
#endif // FWRETRACT #endif // FWRETRACT

View file

@ -206,6 +206,8 @@
#error "Replace SLED_PIN with SOL1_PIN (applies to both Z_PROBE_SLED and SOLENOID_PROBE)." #error "Replace SLED_PIN with SOL1_PIN (applies to both Z_PROBE_SLED and SOLENOID_PROBE)."
#elif defined(CONTROLLERFAN_PIN) #elif defined(CONTROLLERFAN_PIN)
#error "CONTROLLERFAN_PIN is now CONTROLLER_FAN_PIN, enabled with USE_CONTROLLER_FAN. Please update your Configuration_adv.h." #error "CONTROLLERFAN_PIN is now CONTROLLER_FAN_PIN, enabled with USE_CONTROLLER_FAN. Please update your Configuration_adv.h."
#elif defined(MIN_RETRACT)
#error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT. Please update your Configuration_adv.h."
#endif #endif
/** /**

View file

@ -36,7 +36,7 @@
* *
*/ */
#define EEPROM_VERSION "V39" #define EEPROM_VERSION "V40"
// Change EEPROM version if these are changed: // Change EEPROM version if these are changed:
#define EEPROM_OFFSET 100 #define EEPROM_OFFSET 100
@ -125,44 +125,45 @@
* DOGLCD: 2 bytes * DOGLCD: 2 bytes
* 502 M250 C lcd_contrast (uint16_t) * 502 M250 C lcd_contrast (uint16_t)
* *
* FWRETRACT: 29 bytes * FWRETRACT: 33 bytes
* 504 M209 S autoretract_enabled (bool) * 504 M209 S autoretract_enabled (bool)
* 505 M207 S retract_length (float) * 505 M207 S retract_length (float)
* 509 M207 W retract_length_swap (float) * 509 M207 F retract_feedrate_mm_s (float)
* 513 M207 F retract_feedrate_mm_s (float) * 513 M207 Z retract_zlift (float)
* 517 M207 Z retract_zlift (float) * 517 M208 S retract_recover_length (float)
* 521 M208 S retract_recover_length (float) * 521 M208 F retract_recover_feedrate_mm_s (float)
* 525 M208 W retract_recover_length_swap (float) * 525 M207 W swap_retract_length (float)
* 529 M208 F retract_recover_feedrate_mm_s (float) * 529 M208 W swap_retract_recover_length (float)
* 533 M208 R swap_retract_recover_feedrate_mm_s (float)
* *
* Volumetric Extrusion: 21 bytes * Volumetric Extrusion: 21 bytes
* 533 M200 D volumetric_enabled (bool) * 537 M200 D volumetric_enabled (bool)
* 534 M200 T D filament_size (float x5) (T0..3) * 538 M200 T D filament_size (float x5) (T0..3)
* *
* HAVE_TMC2130: 20 bytes * HAVE_TMC2130: 20 bytes
* 554 M906 X Stepper X current (uint16_t) * 558 M906 X Stepper X current (uint16_t)
* 556 M906 Y Stepper Y current (uint16_t) * 560 M906 Y Stepper Y current (uint16_t)
* 558 M906 Z Stepper Z current (uint16_t) * 562 M906 Z Stepper Z current (uint16_t)
* 560 M906 X2 Stepper X2 current (uint16_t) * 564 M906 X2 Stepper X2 current (uint16_t)
* 562 M906 Y2 Stepper Y2 current (uint16_t) * 566 M906 Y2 Stepper Y2 current (uint16_t)
* 564 M906 Z2 Stepper Z2 current (uint16_t) * 568 M906 Z2 Stepper Z2 current (uint16_t)
* 566 M906 E0 Stepper E0 current (uint16_t) * 570 M906 E0 Stepper E0 current (uint16_t)
* 568 M906 E1 Stepper E1 current (uint16_t) * 572 M906 E1 Stepper E1 current (uint16_t)
* 570 M906 E2 Stepper E2 current (uint16_t) * 574 M906 E2 Stepper E2 current (uint16_t)
* 572 M906 E3 Stepper E3 current (uint16_t) * 576 M906 E3 Stepper E3 current (uint16_t)
* 576 M906 E4 Stepper E4 current (uint16_t) * 580 M906 E4 Stepper E4 current (uint16_t)
* *
* LIN_ADVANCE: 8 bytes * LIN_ADVANCE: 8 bytes
* 580 M900 K extruder_advance_k (float) * 584 M900 K extruder_advance_k (float)
* 584 M900 WHD advance_ed_ratio (float) * 588 M900 WHD advance_ed_ratio (float)
* *
* HAS_MOTOR_CURRENT_PWM: * HAS_MOTOR_CURRENT_PWM:
* 588 M907 X Stepper XY current (uint32_t) * 592 M907 X Stepper XY current (uint32_t)
* 592 M907 Z Stepper Z current (uint32_t) * 596 M907 Z Stepper Z current (uint32_t)
* 596 M907 E Stepper E current (uint32_t) * 600 M907 E Stepper E current (uint32_t)
* *
* 600 Minimum end-point * 604 Minimum end-point
* 1921 (600 + 36 + 9 + 288 + 988) Maximum end-point * 1925 (604 + 36 + 9 + 288 + 988) Maximum end-point
* *
* ======================================================================== * ========================================================================
* meshes_begin (between max and min end-point, directly above) * meshes_begin (between max and min end-point, directly above)
@ -520,26 +521,26 @@ void MarlinSettings::postprocess() {
#endif #endif
EEPROM_WRITE(lcd_contrast); EEPROM_WRITE(lcd_contrast);
#if ENABLED(FWRETRACT) #if DISABLED(FWRETRACT)
const bool autoretract_enabled = false;
const float retract_length = 3,
retract_feedrate_mm_s = 45,
retract_zlift = 0,
retract_recover_length = 0,
retract_recover_feedrate_mm_s = 0,
swap_retract_length = 13,
swap_retract_recover_length = 0,
swap_retract_recover_feedrate_mm_s = 8;
#endif
EEPROM_WRITE(autoretract_enabled); EEPROM_WRITE(autoretract_enabled);
EEPROM_WRITE(retract_length); EEPROM_WRITE(retract_length);
#if EXTRUDERS > 1
EEPROM_WRITE(retract_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE(dummy);
#endif
EEPROM_WRITE(retract_feedrate_mm_s); EEPROM_WRITE(retract_feedrate_mm_s);
EEPROM_WRITE(retract_zlift); EEPROM_WRITE(retract_zlift);
EEPROM_WRITE(retract_recover_length); EEPROM_WRITE(retract_recover_length);
#if EXTRUDERS > 1
EEPROM_WRITE(retract_recover_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE(dummy);
#endif
EEPROM_WRITE(retract_recover_feedrate_mm_s); EEPROM_WRITE(retract_recover_feedrate_mm_s);
#endif // FWRETRACT EEPROM_WRITE(swap_retract_length);
EEPROM_WRITE(swap_retract_recover_length);
EEPROM_WRITE(swap_retract_recover_feedrate_mm_s);
EEPROM_WRITE(volumetric_enabled); EEPROM_WRITE(volumetric_enabled);
@ -620,7 +621,7 @@ void MarlinSettings::postprocess() {
EEPROM_WRITE(val); EEPROM_WRITE(val);
#else #else
val = 0; val = 0;
for (uint8_t q = 0; q < 11; ++q) EEPROM_WRITE(val); for (uint8_t q = 11; q--;) EEPROM_WRITE(val);
#endif #endif
// //
@ -701,6 +702,7 @@ void MarlinSettings::postprocess() {
} }
else { else {
float dummy = 0; float dummy = 0;
bool dummyb;
working_crc = 0; //clear before reading first "real data" working_crc = 0; //clear before reading first "real data"
@ -830,7 +832,6 @@ void MarlinSettings::postprocess() {
EEPROM_READ(ubl.state.z_offset); EEPROM_READ(ubl.state.z_offset);
EEPROM_READ(ubl.state.storage_slot); EEPROM_READ(ubl.state.storage_slot);
#else #else
bool dummyb;
uint8_t dummyui8; uint8_t dummyui8;
EEPROM_READ(dummyb); EEPROM_READ(dummyb);
EEPROM_READ(dummy); EEPROM_READ(dummy);
@ -915,21 +916,17 @@ void MarlinSettings::postprocess() {
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
EEPROM_READ(autoretract_enabled); EEPROM_READ(autoretract_enabled);
EEPROM_READ(retract_length); EEPROM_READ(retract_length);
#if EXTRUDERS > 1
EEPROM_READ(retract_length_swap);
#else
EEPROM_READ(dummy);
#endif
EEPROM_READ(retract_feedrate_mm_s); EEPROM_READ(retract_feedrate_mm_s);
EEPROM_READ(retract_zlift); EEPROM_READ(retract_zlift);
EEPROM_READ(retract_recover_length); EEPROM_READ(retract_recover_length);
#if EXTRUDERS > 1
EEPROM_READ(retract_recover_length_swap);
#else
EEPROM_READ(dummy);
#endif
EEPROM_READ(retract_recover_feedrate_mm_s); EEPROM_READ(retract_recover_feedrate_mm_s);
#endif // FWRETRACT EEPROM_READ(swap_retract_length);
EEPROM_READ(swap_retract_recover_length);
EEPROM_READ(swap_retract_recover_feedrate_mm_s);
#else
EEPROM_READ(dummyb);
for (uint8_t q=8; q--;) EEPROM_READ(dummy);
#endif
EEPROM_READ(volumetric_enabled); EEPROM_READ(volumetric_enabled);
@ -1291,17 +1288,14 @@ void MarlinSettings::reset() {
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
autoretract_enabled = false; autoretract_enabled = false;
retract_length = RETRACT_LENGTH; retract_length = RETRACT_LENGTH;
#if EXTRUDERS > 1
retract_length_swap = RETRACT_LENGTH_SWAP;
#endif
retract_feedrate_mm_s = RETRACT_FEEDRATE; retract_feedrate_mm_s = RETRACT_FEEDRATE;
retract_zlift = RETRACT_ZLIFT; retract_zlift = RETRACT_ZLIFT;
retract_recover_length = RETRACT_RECOVER_LENGTH; retract_recover_length = RETRACT_RECOVER_LENGTH;
#if EXTRUDERS > 1
retract_recover_length_swap = RETRACT_RECOVER_LENGTH_SWAP;
#endif
retract_recover_feedrate_mm_s = RETRACT_RECOVER_FEEDRATE; retract_recover_feedrate_mm_s = RETRACT_RECOVER_FEEDRATE;
#endif swap_retract_length = RETRACT_LENGTH_SWAP;
swap_retract_recover_length = RETRACT_RECOVER_LENGTH_SWAP;
swap_retract_recover_feedrate_mm_s = RETRACT_RECOVER_FEEDRATE_SWAP;
#endif // FWRETRACT
volumetric_enabled = volumetric_enabled =
#if ENABLED(VOLUMETRIC_DEFAULT_ON) #if ENABLED(VOLUMETRIC_DEFAULT_ON)
@ -1753,9 +1747,7 @@ void MarlinSettings::reset() {
} }
CONFIG_ECHO_START; CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M207 S", LINEAR_UNIT(retract_length)); SERIAL_ECHOPAIR(" M207 S", LINEAR_UNIT(retract_length));
#if EXTRUDERS > 1 SERIAL_ECHOPAIR(" W", LINEAR_UNIT(swap_retract_length));
SERIAL_ECHOPAIR(" W", LINEAR_UNIT(retract_length_swap));
#endif
SERIAL_ECHOPAIR(" F", MMS_TO_MMM(LINEAR_UNIT(retract_feedrate_mm_s))); SERIAL_ECHOPAIR(" F", MMS_TO_MMM(LINEAR_UNIT(retract_feedrate_mm_s)));
SERIAL_ECHOLNPAIR(" Z", LINEAR_UNIT(retract_zlift)); SERIAL_ECHOLNPAIR(" Z", LINEAR_UNIT(retract_zlift));
@ -1765,14 +1757,12 @@ void MarlinSettings::reset() {
} }
CONFIG_ECHO_START; CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M208 S", LINEAR_UNIT(retract_recover_length)); SERIAL_ECHOPAIR(" M208 S", LINEAR_UNIT(retract_recover_length));
#if EXTRUDERS > 1 SERIAL_ECHOPAIR(" W", LINEAR_UNIT(swap_retract_recover_length));
SERIAL_ECHOPAIR(" W", LINEAR_UNIT(retract_recover_length_swap));
#endif
SERIAL_ECHOLNPAIR(" F", MMS_TO_MMM(LINEAR_UNIT(retract_recover_feedrate_mm_s))); SERIAL_ECHOLNPAIR(" F", MMS_TO_MMM(LINEAR_UNIT(retract_recover_feedrate_mm_s)));
if (!forReplay) { if (!forReplay) {
CONFIG_ECHO_START; CONFIG_ECHO_START;
SERIAL_ECHOLNPGM("Auto-Retract: S=0 to disable, 1 to interpret extrude-only moves as retracts or recoveries"); SERIAL_ECHOLNPGM("Auto-Retract: S=0 to disable, 1 to interpret E-only moves as retract/recover");
} }
CONFIG_ECHO_START; CONFIG_ECHO_START;
SERIAL_ECHOLNPAIR(" M209 S", autoretract_enabled ? 1 : 0); SERIAL_ECHOLNPAIR(" M209 S", autoretract_enabled ? 1 : 0);

View file

@ -757,7 +757,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -767,7 +767,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -764,7 +764,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -774,7 +774,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -764,7 +764,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -774,7 +774,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -757,7 +757,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -767,7 +767,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -740,7 +740,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -750,7 +750,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -757,7 +757,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -767,7 +767,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -757,7 +757,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -767,7 +767,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -757,7 +757,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -767,7 +767,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -764,7 +764,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -774,7 +774,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -754,7 +754,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -764,7 +764,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -764,7 +764,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -774,7 +774,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -757,7 +757,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -767,7 +767,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -757,7 +757,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -767,7 +767,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 35 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 35 // Default feedrate for retracting (mm/s)

View file

@ -760,7 +760,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -770,7 +770,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -770,7 +770,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -780,7 +780,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -757,7 +757,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -767,7 +767,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -762,7 +762,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -772,7 +772,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -761,7 +761,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -771,7 +771,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -759,7 +759,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -769,7 +769,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -759,7 +759,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -769,7 +769,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -764,7 +764,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -774,7 +774,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -759,7 +759,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -769,7 +769,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -764,7 +764,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -774,7 +774,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -757,7 +757,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -767,7 +767,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -757,7 +757,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -767,7 +767,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -764,7 +764,7 @@
* Use M207 and M208 to define parameters for retract / recover. * Use M207 and M208 to define parameters for retract / recover.
* *
* Use M209 to enable or disable auto-retract. * Use M209 to enable or disable auto-retract.
* With auto-retract enabled, all G1 E moves over the MIN_RETRACT length * With auto-retract enabled, all G1 E moves within the set range
* will be converted to firmware-based retract/recover moves. * will be converted to firmware-based retract/recover moves.
* *
* Be sure to turn off auto-retract during filament change. * Be sure to turn off auto-retract during filament change.
@ -774,7 +774,8 @@
*/ */
//#define FWRETRACT // ONLY PARTIALLY TESTED //#define FWRETRACT // ONLY PARTIALLY TESTED
#if ENABLED(FWRETRACT) #if ENABLED(FWRETRACT)
#define MIN_RETRACT 0.1 // A retract/recover of this length or longer can be converted to auto-retract #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
#define RETRACT_LENGTH 3 // Default retract length (positive mm) #define RETRACT_LENGTH 3 // Default retract length (positive mm)
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)

View file

@ -134,11 +134,11 @@
#define MSG_KILLED _UxGT("已杀掉") //"KILLED. " #define MSG_KILLED _UxGT("已杀掉") //"KILLED. "
#define MSG_STOPPED _UxGT("已停止") //"STOPPED. " #define MSG_STOPPED _UxGT("已停止") //"STOPPED. "
#define MSG_CONTROL_RETRACT _UxGT("回抽长度mm") //"Retract mm" retract_length, retract length (positive mm) #define MSG_CONTROL_RETRACT _UxGT("回抽长度mm") //"Retract mm" retract_length, retract length (positive mm)
#define MSG_CONTROL_RETRACT_SWAP _UxGT("换手回抽长度mm") //"Swap Re.mm" retract_length_swap, swap retract length (positive mm), for extruder change #define MSG_CONTROL_RETRACT_SWAP _UxGT("换手回抽长度mm") //"Swap Re.mm" swap_retract_length, swap retract length (positive mm), for extruder change
#define MSG_CONTROL_RETRACTF _UxGT("回抽速率mm/s") //"Retract V" retract_feedrate_mm_s, feedrate for retracting (mm/s) #define MSG_CONTROL_RETRACTF _UxGT("回抽速率mm/s") //"Retract V" retract_feedrate_mm_s, feedrate for retracting (mm/s)
#define MSG_CONTROL_RETRACT_ZLIFT _UxGT("Hop mm") //"Hop mm" retract_zlift, retract Z-lift #define MSG_CONTROL_RETRACT_ZLIFT _UxGT("Hop mm") //"Hop mm" retract_zlift, retract Z-lift
#define MSG_CONTROL_RETRACT_RECOVER _UxGT("回抽恢复长度mm") //"UnRet +mm" retract_recover_length, additional recover length (mm, added to retract length when recovering) #define MSG_CONTROL_RETRACT_RECOVER _UxGT("回抽恢复长度mm") //"UnRet +mm" retract_recover_length, additional recover length (mm, added to retract length when recovering)
#define MSG_CONTROL_RETRACT_RECOVER_SWAP _UxGT("换手回抽恢复长度mm") //"S UnRet+mm" retract_recover_length_swap, additional swap recover length (mm, added to retract length when recovering from extruder change) #define MSG_CONTROL_RETRACT_RECOVER_SWAP _UxGT("换手回抽恢复长度mm") //"S UnRet+mm" swap_retract_recover_length, additional swap recover length (mm, added to retract length when recovering from extruder change)
#define MSG_CONTROL_RETRACT_RECOVERF _UxGT("回抽恢复后进料速率mm/s") //"UnRet V" retract_recover_feedrate_mm_s, feedrate for recovering from retraction (mm/s) #define MSG_CONTROL_RETRACT_RECOVERF _UxGT("回抽恢复后进料速率mm/s") //"UnRet V" retract_recover_feedrate_mm_s, feedrate for recovering from retraction (mm/s)
#define MSG_AUTORETRACT _UxGT("自动抽回") //"AutoRetr." autoretract_enabled, #define MSG_AUTORETRACT _UxGT("自动抽回") //"AutoRetr." autoretract_enabled,
#define MSG_FILAMENTCHANGE _UxGT("更换丝料") //"Change filament" #define MSG_FILAMENTCHANGE _UxGT("更换丝料") //"Change filament"

View file

@ -134,11 +134,11 @@
#define MSG_KILLED _UxGT("已殺掉") //"KILLED. " #define MSG_KILLED _UxGT("已殺掉") //"KILLED. "
#define MSG_STOPPED _UxGT("已停止") //"STOPPED. " #define MSG_STOPPED _UxGT("已停止") //"STOPPED. "
#define MSG_CONTROL_RETRACT _UxGT("回抽長度mm") //"Retract mm" retract_length, retract length (positive mm) #define MSG_CONTROL_RETRACT _UxGT("回抽長度mm") //"Retract mm" retract_length, retract length (positive mm)
#define MSG_CONTROL_RETRACT_SWAP _UxGT("換手回抽長度mm") //"Swap Re.mm" retract_length_swap, swap retract length (positive mm), for extruder change #define MSG_CONTROL_RETRACT_SWAP _UxGT("換手回抽長度mm") //"Swap Re.mm" swap_retract_length, swap retract length (positive mm), for extruder change
#define MSG_CONTROL_RETRACTF _UxGT("回抽速率mm/s") //"Retract V" retract_feedrate_mm_s, feedrate for retracting (mm/s) #define MSG_CONTROL_RETRACTF _UxGT("回抽速率mm/s") //"Retract V" retract_feedrate_mm_s, feedrate for retracting (mm/s)
#define MSG_CONTROL_RETRACT_ZLIFT _UxGT("Hop mm") //"Hop mm" retract_zlift, retract Z-lift #define MSG_CONTROL_RETRACT_ZLIFT _UxGT("Hop mm") //"Hop mm" retract_zlift, retract Z-lift
#define MSG_CONTROL_RETRACT_RECOVER _UxGT("回抽恢複長度mm") //"UnRet +mm" retract_recover_length, additional recover length (mm, added to retract length when recovering) #define MSG_CONTROL_RETRACT_RECOVER _UxGT("回抽恢複長度mm") //"UnRet +mm" retract_recover_length, additional recover length (mm, added to retract length when recovering)
#define MSG_CONTROL_RETRACT_RECOVER_SWAP _UxGT("換手回抽恢複長度mm") //"S UnRet+mm" retract_recover_length_swap, additional swap recover length (mm, added to retract length when recovering from extruder change) #define MSG_CONTROL_RETRACT_RECOVER_SWAP _UxGT("換手回抽恢複長度mm") //"S UnRet+mm" swap_retract_recover_length, additional swap recover length (mm, added to retract length when recovering from extruder change)
#define MSG_CONTROL_RETRACT_RECOVERF _UxGT("回抽恢複後進料速率mm/s") //"UnRet V" retract_recover_feedrate_mm_s, feedrate for recovering from retraction (mm/s) #define MSG_CONTROL_RETRACT_RECOVERF _UxGT("回抽恢複後進料速率mm/s") //"UnRet V" retract_recover_feedrate_mm_s, feedrate for recovering from retraction (mm/s)
#define MSG_AUTORETRACT _UxGT("自動抽回") //"AutoRetr." autoretract_enabled, #define MSG_AUTORETRACT _UxGT("自動抽回") //"AutoRetr." autoretract_enabled,
#define MSG_FILAMENTCHANGE _UxGT("更換絲料") //"Change filament" #define MSG_FILAMENTCHANGE _UxGT("更換絲料") //"Change filament"

View file

@ -3380,13 +3380,13 @@ void kill_screen(const char* lcd_msg) {
MENU_ITEM_EDIT(bool, MSG_AUTORETRACT, &autoretract_enabled); MENU_ITEM_EDIT(bool, MSG_AUTORETRACT, &autoretract_enabled);
MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT, &retract_length, 0, 100); MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT, &retract_length, 0, 100);
#if EXTRUDERS > 1 #if EXTRUDERS > 1
MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_SWAP, &retract_length_swap, 0, 100); MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_SWAP, &swap_retract_length, 0, 100);
#endif #endif
MENU_ITEM_EDIT(float3, MSG_CONTROL_RETRACTF, &retract_feedrate_mm_s, 1, 999); MENU_ITEM_EDIT(float3, MSG_CONTROL_RETRACTF, &retract_feedrate_mm_s, 1, 999);
MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_ZLIFT, &retract_zlift, 0, 999); MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_ZLIFT, &retract_zlift, 0, 999);
MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_RECOVER, &retract_recover_length, -100, 100); MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_RECOVER, &retract_recover_length, -100, 100);
#if EXTRUDERS > 1 #if EXTRUDERS > 1
MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_RECOVER_SWAP, &retract_recover_length_swap, -100, 100); MENU_ITEM_EDIT(float52, MSG_CONTROL_RETRACT_RECOVER_SWAP, &swap_retract_recover_length, -100, 100);
#endif #endif
MENU_ITEM_EDIT(float3, MSG_CONTROL_RETRACT_RECOVERF, &retract_recover_feedrate_mm_s, 1, 999); MENU_ITEM_EDIT(float3, MSG_CONTROL_RETRACT_RECOVERF, &retract_recover_feedrate_mm_s, 1, 999);
END_MENU(); END_MENU();