Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
This commit is contained in:
commit
2acd3792fc
13 changed files with 2330 additions and 162 deletions
|
@ -70,6 +70,7 @@
|
|||
// 91 = Final OMCA board
|
||||
// 301= Rambo
|
||||
// 21 = Elefu Ra Board (v3)
|
||||
// 88 = 5DPrint D8 Driver Board
|
||||
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD 7
|
||||
|
@ -115,8 +116,10 @@
|
|||
// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
|
||||
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
|
||||
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
|
||||
// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
|
||||
// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
|
||||
// 20 is the PT100 circuit found in the Ultimainboard V2.x
|
||||
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor
|
||||
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
|
||||
//
|
||||
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
|
||||
// (but gives greater accuracy and more stable PID)
|
||||
|
@ -459,6 +462,15 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//=============================Additional Features===========================
|
||||
//===========================================================================
|
||||
|
||||
// Custom M code points
|
||||
#define CUSTOM_M_CODES
|
||||
#ifdef CUSTOM_M_CODES
|
||||
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
|
||||
#define Z_PROBE_OFFSET_RANGE_MIN -15
|
||||
#define Z_PROBE_OFFSET_RANGE_MAX -5
|
||||
#endif
|
||||
|
||||
|
||||
// EEPROM
|
||||
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
|
||||
// M500 - stores parameters in EEPROM
|
||||
|
|
|
@ -30,7 +30,7 @@
|
|||
|
||||
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
|
||||
//The maximum buffered steps/sec of the extruder motor are called "se".
|
||||
//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
|
||||
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
|
||||
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
|
||||
// you exit the value by any M109 without F*
|
||||
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
|
||||
|
@ -215,7 +215,7 @@
|
|||
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
|
||||
#define X_HOME_RETRACT_MM 5
|
||||
#define Y_HOME_RETRACT_MM 5
|
||||
#define Z_HOME_RETRACT_MM 1
|
||||
#define Z_HOME_RETRACT_MM 2
|
||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||
|
||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||
|
@ -410,10 +410,10 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|||
#ifdef FWRETRACT
|
||||
#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
|
||||
#define RETRACT_LENGTH 3 //default retract length (positive mm)
|
||||
#define RETRACT_FEEDRATE 80*60 //default feedrate for retracting
|
||||
#define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
|
||||
#define RETRACT_ZLIFT 0 //default retract Z-lift
|
||||
#define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
|
||||
#define RETRACT_RECOVER_FEEDRATE 8*60 //default feedrate for recovering from retraction
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
|
|
|
@ -118,6 +118,7 @@
|
|||
// M107 - Fan off
|
||||
// M109 - Sxxx Wait for extruder current temp to reach target temp. Waits only when heating
|
||||
// Rxxx Wait for extruder current temp to reach target temp. Waits when heating and cooling
|
||||
// IF AUTOTEMP is enabled, S<mintemp> B<maxtemp> F<factor>. Exit autotemp by any M109 without F
|
||||
// M114 - Output current position to serial port
|
||||
// M115 - Capabilities string
|
||||
// M117 - display message
|
||||
|
@ -1119,7 +1120,7 @@ void refresh_cmd_timeout(void)
|
|||
current_position[E_AXIS]+=retract_length/volumetric_multiplier[active_extruder];
|
||||
plan_set_e_position(current_position[E_AXIS]);
|
||||
float oldFeedrate = feedrate;
|
||||
feedrate=retract_feedrate;
|
||||
feedrate=retract_feedrate*60;
|
||||
retracted=true;
|
||||
prepare_move();
|
||||
current_position[Z_AXIS]-=retract_zlift;
|
||||
|
@ -1137,7 +1138,7 @@ void refresh_cmd_timeout(void)
|
|||
current_position[E_AXIS]-=(retract_length+retract_recover_length)/volumetric_multiplier[active_extruder];
|
||||
plan_set_e_position(current_position[E_AXIS]);
|
||||
float oldFeedrate = feedrate;
|
||||
feedrate=retract_recover_feedrate;
|
||||
feedrate=retract_recover_feedrate*60;
|
||||
retracted=false;
|
||||
prepare_move();
|
||||
feedrate = oldFeedrate;
|
||||
|
@ -1287,6 +1288,11 @@ void process_commands()
|
|||
feedrate = homing_feedrate[X_AXIS];
|
||||
if(homing_feedrate[Y_AXIS]<feedrate)
|
||||
feedrate = homing_feedrate[Y_AXIS];
|
||||
if (max_length(X_AXIS) > max_length(Y_AXIS)) {
|
||||
feedrate *= sqrt(pow(max_length(Y_AXIS) / max_length(X_AXIS), 2) + 1);
|
||||
} else {
|
||||
feedrate *= sqrt(pow(max_length(X_AXIS) / max_length(Y_AXIS), 2) + 1);
|
||||
}
|
||||
plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder);
|
||||
st_synchronize();
|
||||
|
||||
|
@ -2268,8 +2274,6 @@ void process_commands()
|
|||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHO(MSG_M200_INVALID_EXTRUDER);
|
||||
}
|
||||
SERIAL_ECHOLN(tmp_extruder);
|
||||
break;
|
||||
}
|
||||
volumetric_multiplier[tmp_extruder] = 1 / area;
|
||||
}
|
||||
|
@ -2341,7 +2345,7 @@ void process_commands()
|
|||
break;
|
||||
#endif
|
||||
#ifdef FWRETRACT
|
||||
case 207: //M207 - set retract length S[positive mm] F[feedrate mm/sec] Z[additional zlift/hop]
|
||||
case 207: //M207 - set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop]
|
||||
{
|
||||
if(code_seen('S'))
|
||||
{
|
||||
|
@ -2349,14 +2353,14 @@ void process_commands()
|
|||
}
|
||||
if(code_seen('F'))
|
||||
{
|
||||
retract_feedrate = code_value() ;
|
||||
retract_feedrate = code_value()/60 ;
|
||||
}
|
||||
if(code_seen('Z'))
|
||||
{
|
||||
retract_zlift = code_value() ;
|
||||
}
|
||||
}break;
|
||||
case 208: // M208 - set retract recover length S[positive mm surplus to the M207 S*] F[feedrate mm/sec]
|
||||
case 208: // M208 - set retract recover length S[positive mm surplus to the M207 S*] F[feedrate mm/min]
|
||||
{
|
||||
if(code_seen('S'))
|
||||
{
|
||||
|
@ -2364,7 +2368,7 @@ void process_commands()
|
|||
}
|
||||
if(code_seen('F'))
|
||||
{
|
||||
retract_recover_feedrate = code_value() ;
|
||||
retract_recover_feedrate = code_value()/60 ;
|
||||
}
|
||||
}break;
|
||||
case 209: // M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
|
||||
|
@ -2721,6 +2725,43 @@ void process_commands()
|
|||
}
|
||||
break;
|
||||
#endif
|
||||
|
||||
#ifdef CUSTOM_M_CODE_SET_Z_PROBE_OFFSET
|
||||
case CUSTOM_M_CODE_SET_Z_PROBE_OFFSET:
|
||||
{
|
||||
float value;
|
||||
if (code_seen('Z'))
|
||||
{
|
||||
value = code_value();
|
||||
if ((Z_PROBE_OFFSET_RANGE_MIN <= value) && (value <= Z_PROBE_OFFSET_RANGE_MAX))
|
||||
{
|
||||
zprobe_zoffset = -value; // compare w/ line 278 of ConfigurationStore.cpp
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOLNPGM(MSG_ZPROBE_ZOFFSET " " MSG_OK);
|
||||
SERIAL_PROTOCOLLN("");
|
||||
}
|
||||
else
|
||||
{
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOPGM(MSG_ZPROBE_ZOFFSET);
|
||||
SERIAL_ECHOPGM(MSG_Z_MIN);
|
||||
SERIAL_ECHO(Z_PROBE_OFFSET_RANGE_MIN);
|
||||
SERIAL_ECHOPGM(MSG_Z_MAX);
|
||||
SERIAL_ECHO(Z_PROBE_OFFSET_RANGE_MAX);
|
||||
SERIAL_PROTOCOLLN("");
|
||||
}
|
||||
}
|
||||
else
|
||||
{
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOLNPGM(MSG_ZPROBE_ZOFFSET " : ");
|
||||
SERIAL_ECHO(-zprobe_zoffset);
|
||||
SERIAL_PROTOCOLLN("");
|
||||
}
|
||||
break;
|
||||
}
|
||||
#endif // CUSTOM_M_CODE_SET_Z_PROBE_OFFSET
|
||||
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
case 600: //Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
|
||||
{
|
||||
|
@ -3051,7 +3092,16 @@ void process_commands()
|
|||
// Set the new active extruder and position
|
||||
active_extruder = tmp_extruder;
|
||||
#endif //else DUAL_X_CARRIAGE
|
||||
#ifdef DELTA
|
||||
|
||||
calculate_delta(current_position); // change cartesian kinematic to delta kinematic;
|
||||
//sent position to plan_set_position();
|
||||
plan_set_position(delta[X_AXIS], delta[Y_AXIS], delta[Z_AXIS],current_position[E_AXIS]);
|
||||
|
||||
#else
|
||||
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
|
||||
|
||||
#endif
|
||||
// Move to the old position if 'F' was in the parameters
|
||||
if(make_move && Stopped == false) {
|
||||
prepare_move();
|
||||
|
|
|
@ -6,8 +6,13 @@
|
|||
#include "Wire.h"
|
||||
|
||||
// Settings for the I2C based DIGIPOT (MCP4451) on Azteeg X3 Pro
|
||||
#if MOTHERBOARD == 88
|
||||
#define DIGIPOT_I2C_FACTOR 117.96
|
||||
#define DIGIPOT_I2C_MAX_CURRENT 1.736
|
||||
#else
|
||||
#define DIGIPOT_I2C_FACTOR 106.7
|
||||
#define DIGIPOT_I2C_MAX_CURRENT 2.5
|
||||
#endif
|
||||
|
||||
static byte current_to_wiper( float current ){
|
||||
return byte(ceil(float((DIGIPOT_I2C_FACTOR*current))));
|
||||
|
|
725
Marlin/example_configurations/makibox/Configuration.h
Normal file
725
Marlin/example_configurations/makibox/Configuration.h
Normal file
|
@ -0,0 +1,725 @@
|
|||
#ifndef CONFIGURATION_H
|
||||
#define CONFIGURATION_H
|
||||
|
||||
// This configuration file contains the basic settings.
|
||||
// Advanced settings can be found in Configuration_adv.h
|
||||
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
||||
//===========================================================================
|
||||
//============================= DELTA Printer ===============================
|
||||
//===========================================================================
|
||||
// For a Delta printer replace the configuration files with the files in the
|
||||
// example_configurations/delta directory.
|
||||
//
|
||||
|
||||
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
||||
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
|
||||
// build by the user have been successfully uploaded into firmware.
|
||||
#define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time
|
||||
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
|
||||
|
||||
// SERIAL_PORT selects which serial port should be used for communication with the host.
|
||||
// This allows the connection of wireless adapters (for instance) to non-default port pins.
|
||||
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
|
||||
#define SERIAL_PORT 0
|
||||
|
||||
// This determines the communication speed of the printer
|
||||
// This determines the communication speed of the printer
|
||||
#define BAUDRATE 250000
|
||||
|
||||
// This enables the serial port associated to the Bluetooth interface
|
||||
//#define BTENABLED // Enable BT interface on AT90USB devices
|
||||
|
||||
|
||||
//// The following define selects which electronics board you have. Please choose the one that matches your setup
|
||||
// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
|
||||
// 11 = Gen7 v1.1, v1.2 = 11
|
||||
// 12 = Gen7 v1.3
|
||||
// 13 = Gen7 v1.4
|
||||
// 2 = Cheaptronic v1.0
|
||||
// 20 = Sethi 3D_1
|
||||
// 3 = MEGA/RAMPS up to 1.2 = 3
|
||||
// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
|
||||
// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
|
||||
// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
|
||||
// 4 = Duemilanove w/ ATMega328P pin assignment
|
||||
// 5 = Gen6
|
||||
// 51 = Gen6 deluxe
|
||||
// 6 = Sanguinololu < 1.2
|
||||
// 62 = Sanguinololu 1.2 and above
|
||||
// 63 = Melzi
|
||||
// 64 = STB V1.1
|
||||
// 65 = Azteeg X1
|
||||
// 66 = Melzi with ATmega1284 (MaKr3d version)
|
||||
// 67 = Azteeg X3
|
||||
// 68 = Azteeg X3 Pro
|
||||
// 7 = Ultimaker
|
||||
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
|
||||
// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
||||
// 77 = 3Drag Controller
|
||||
// 8 = Teensylu
|
||||
// 80 = Rumba
|
||||
// 81 = Printrboard (AT90USB1286)
|
||||
// 82 = Brainwave (AT90USB646)
|
||||
// 83 = SAV Mk-I (AT90USB1286)
|
||||
// 9 = Gen3+
|
||||
// 70 = Megatronics
|
||||
// 701= Megatronics v2.0
|
||||
// 702= Minitronics v1.0
|
||||
// 90 = Alpha OMCA board
|
||||
// 91 = Final OMCA board
|
||||
// 301= Rambo
|
||||
// 21 = Elefu Ra Board (v3)
|
||||
// 88 = 5DPrint D8 Driver Board
|
||||
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD 88
|
||||
#endif
|
||||
|
||||
// Define this to set a custom name for your generic Mendel,
|
||||
// #define CUSTOM_MENDEL_NAME "This Mendel"
|
||||
|
||||
// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// This defines the number of extruders
|
||||
#define EXTRUDERS 1
|
||||
|
||||
//// The following define selects which power supply you have. Please choose the one that matches your setup
|
||||
// 1 = ATX
|
||||
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
|
||||
|
||||
#define POWER_SUPPLY 1
|
||||
|
||||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
// #define PS_DEFAULT_OFF
|
||||
|
||||
//===========================================================================
|
||||
//=============================Thermal Settings ============================
|
||||
//===========================================================================
|
||||
//
|
||||
//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
|
||||
//
|
||||
//// Temperature sensor settings:
|
||||
// -2 is thermocouple with MAX6675 (only for sensor 0)
|
||||
// -1 is thermocouple with AD595
|
||||
// 0 is not used
|
||||
// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
|
||||
// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
|
||||
// 3 is Mendel-parts thermistor (4.7k pullup)
|
||||
// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
|
||||
// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
|
||||
// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
|
||||
// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
|
||||
// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
|
||||
// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
|
||||
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
|
||||
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
|
||||
// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
|
||||
// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
|
||||
// 20 is the PT100 circuit found in the Ultimainboard V2.x
|
||||
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
|
||||
//
|
||||
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
|
||||
// (but gives greater accuracy and more stable PID)
|
||||
// 51 is 100k thermistor - EPCOS (1k pullup)
|
||||
// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
|
||||
// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
|
||||
//
|
||||
// 1047 is Pt1000 with 4k7 pullup
|
||||
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
// 147 is Pt100 with 4k7 pullup
|
||||
// 110 is Pt100 with 1k pullup (non standard)
|
||||
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_BED 12
|
||||
|
||||
// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
|
||||
//#define TEMP_SENSOR_1_AS_REDUNDANT
|
||||
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
|
||||
|
||||
// Actual temperature must be close to target for this long before M109 returns success
|
||||
#define TEMP_RESIDENCY_TIME 10 // (seconds)
|
||||
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
|
||||
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
|
||||
|
||||
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
|
||||
// to check that the wiring to the thermistor is not broken.
|
||||
// Otherwise this would lead to the heater being powered on all the time.
|
||||
#define HEATER_0_MINTEMP 5
|
||||
#define HEATER_1_MINTEMP 5
|
||||
#define HEATER_2_MINTEMP 5
|
||||
#define BED_MINTEMP 5
|
||||
|
||||
// When temperature exceeds max temp, your heater will be switched off.
|
||||
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
|
||||
// You should use MINTEMP for thermistor short/failure protection.
|
||||
#define HEATER_0_MAXTEMP 275
|
||||
#define HEATER_1_MAXTEMP 275
|
||||
#define HEATER_2_MAXTEMP 275
|
||||
#define BED_MAXTEMP 150
|
||||
|
||||
// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
|
||||
// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
|
||||
// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
|
||||
//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
|
||||
|
||||
// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
|
||||
//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R
|
||||
//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R
|
||||
|
||||
// PID settings:
|
||||
// Comment the following line to disable PID and enable bang-bang.
|
||||
#define PIDTEMP
|
||||
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
||||
#define PID_MAX 255 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#ifdef PIDTEMP
|
||||
//#define PID_DEBUG // Sends debug data to the serial port.
|
||||
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
|
||||
#define K1 0.95 //smoothing factor within the PID
|
||||
#define PID_dT ((OVERSAMPLENR * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
||||
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
// Ultimaker
|
||||
#define DEFAULT_Kp 22.2
|
||||
#define DEFAULT_Ki 1.08
|
||||
#define DEFAULT_Kd 114
|
||||
|
||||
// MakerGear
|
||||
// #define DEFAULT_Kp 7.0
|
||||
// #define DEFAULT_Ki 0.1
|
||||
// #define DEFAULT_Kd 12
|
||||
|
||||
// Mendel Parts V9 on 12V
|
||||
// #define DEFAULT_Kp 63.0
|
||||
// #define DEFAULT_Ki 2.25
|
||||
// #define DEFAULT_Kd 440
|
||||
#endif // PIDTEMP
|
||||
|
||||
// Bed Temperature Control
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
#define MAX_BED_POWER 175 // limits duty cycle to bed; 255=full current
|
||||
// This limit is set to 175 by default in the Makibox configuration and it can adjusted
|
||||
// to increase the heat up rate. However, if changed, user must be aware of the safety concerns
|
||||
// of drawing too much current from the power supply.
|
||||
|
||||
#ifdef PIDTEMPBED
|
||||
//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
#define DEFAULT_bedKp 10.00
|
||||
#define DEFAULT_bedKi .023
|
||||
#define DEFAULT_bedKd 305.4
|
||||
|
||||
//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from pidautotune
|
||||
// #define DEFAULT_bedKp 97.1
|
||||
// #define DEFAULT_bedKi 1.41
|
||||
// #define DEFAULT_bedKd 1675.16
|
||||
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#endif // PIDTEMPBED
|
||||
|
||||
|
||||
|
||||
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
||||
//can be software-disabled for whatever purposes by
|
||||
#define PREVENT_DANGEROUS_EXTRUDE
|
||||
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
|
||||
#define PREVENT_LENGTHY_EXTRUDE
|
||||
|
||||
#define EXTRUDE_MINTEMP 170
|
||||
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
||||
|
||||
//===========================================================================
|
||||
//=============================Mechanical Settings===========================
|
||||
//===========================================================================
|
||||
|
||||
// Uncomment the following line to enable CoreXY kinematics
|
||||
// #define COREXY
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
#ifndef ENDSTOPPULLUPS
|
||||
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
||||
// #define ENDSTOPPULLUP_XMAX
|
||||
// #define ENDSTOPPULLUP_YMAX
|
||||
// #define ENDSTOPPULLUP_ZMAX
|
||||
// #define ENDSTOPPULLUP_XMIN
|
||||
// #define ENDSTOPPULLUP_YMIN
|
||||
// #define ENDSTOPPULLUP_ZMIN
|
||||
#endif
|
||||
|
||||
#ifdef ENDSTOPPULLUPS
|
||||
#define ENDSTOPPULLUP_XMAX
|
||||
#define ENDSTOPPULLUP_YMAX
|
||||
#define ENDSTOPPULLUP_ZMAX
|
||||
#define ENDSTOPPULLUP_XMIN
|
||||
#define ENDSTOPPULLUP_YMIN
|
||||
#define ENDSTOPPULLUP_ZMIN
|
||||
#endif
|
||||
|
||||
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
|
||||
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
// Disable max endstops for compatibility with endstop checking routine
|
||||
#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
#endif
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
#define X_ENABLE_ON 0
|
||||
#define Y_ENABLE_ON 0
|
||||
#define Z_ENABLE_ON 0
|
||||
#define E_ENABLE_ON 0 // For all extruders
|
||||
|
||||
// Disables axis when it's not being used.
|
||||
#define DISABLE_X false
|
||||
#define DISABLE_Y false
|
||||
#define DISABLE_Z false
|
||||
#define DISABLE_E false // For all extruders
|
||||
|
||||
#define INVERT_X_DIR false // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
|
||||
#define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_E0_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
|
||||
// ENDSTOP SETTINGS:
|
||||
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
||||
#define X_HOME_DIR -1
|
||||
#define Y_HOME_DIR -1
|
||||
#define Z_HOME_DIR -1
|
||||
|
||||
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
|
||||
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
|
||||
// Travel limits after homing
|
||||
#define X_MAX_POS 110
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MAX_POS 150
|
||||
#define Y_MIN_POS 0
|
||||
#define Z_MAX_POS 86
|
||||
#define Z_MIN_POS 0
|
||||
|
||||
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
|
||||
#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
|
||||
#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
|
||||
//============================= Bed Auto Leveling ===========================
|
||||
|
||||
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
|
||||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
// There are 2 different ways to pick the X and Y locations to probe:
|
||||
|
||||
// - "grid" mode
|
||||
// Probe every point in a rectangular grid
|
||||
// You must specify the rectangle, and the density of sample points
|
||||
// This mode is preferred because there are more measurements.
|
||||
// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
|
||||
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You must specify the X & Y coordinates of all 3 points
|
||||
|
||||
#define AUTO_BED_LEVELING_GRID
|
||||
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
|
||||
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
|
||||
// and least squares solution is calculated
|
||||
// Note: this feature occupies 10'206 byte
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
#define LEFT_PROBE_BED_POSITION 15
|
||||
#define RIGHT_PROBE_BED_POSITION 170
|
||||
#define BACK_PROBE_BED_POSITION 180
|
||||
#define FRONT_PROBE_BED_POSITION 20
|
||||
|
||||
// set the number of grid points per dimension
|
||||
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||
|
||||
|
||||
#else // not AUTO_BED_LEVELING_GRID
|
||||
// with no grid, just probe 3 arbitrary points. A simple cross-product
|
||||
// is used to esimate the plane of the print bed
|
||||
|
||||
#define ABL_PROBE_PT_1_X 15
|
||||
#define ABL_PROBE_PT_1_Y 180
|
||||
#define ABL_PROBE_PT_2_X 15
|
||||
#define ABL_PROBE_PT_2_Y 20
|
||||
#define ABL_PROBE_PT_3_X 170
|
||||
#define ABL_PROBE_PT_3_Y 20
|
||||
|
||||
#endif // AUTO_BED_LEVELING_GRID
|
||||
|
||||
|
||||
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
|
||||
|
||||
#define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
|
||||
// Be sure you have this distance over your Z_MAX_POS in case
|
||||
|
||||
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min
|
||||
|
||||
#define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
|
||||
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
|
||||
|
||||
|
||||
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
|
||||
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
|
||||
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
|
||||
|
||||
// #define PROBE_SERVO_DEACTIVATION_DELAY 300
|
||||
|
||||
|
||||
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
||||
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
|
||||
|
||||
#define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area.
|
||||
// When defined, it will:
|
||||
// - Allow Z homing only after X and Y homing AND stepper drivers still enabled
|
||||
// - If stepper drivers timeout, it will need X and Y homing again before Z homing
|
||||
// - Position the probe in a defined XY point before Z Homing when homing all axis (G28)
|
||||
// - Block Z homing only when the probe is outside bed area.
|
||||
|
||||
#ifdef Z_SAFE_HOMING
|
||||
|
||||
#define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2) // X point for Z homing when homing all axis (G28)
|
||||
#define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2) // Y point for Z homing when homing all axis (G28)
|
||||
|
||||
#endif
|
||||
|
||||
#endif // ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
|
||||
//Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
|
||||
//// MOVEMENT SETTINGS
|
||||
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
|
||||
#define HOMING_FEEDRATE {1500, 1500, 120, 0} // set the homing speeds (mm/min) ***** MakiBox A6 *****
|
||||
|
||||
// default settings
|
||||
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {400, 400, 400, 163} // default steps per unit for ***** MakiBox A6 *****
|
||||
#define DEFAULT_MAX_FEEDRATE {60, 60, 20, 45} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {2000,2000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||
// For the other hotends it is their distance from the extruder 0 hotend.
|
||||
// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||
#define DEFAULT_XYJERK 20.0 // (mm/sec)
|
||||
#define DEFAULT_ZJERK 0.4 // (mm/sec)
|
||||
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
||||
|
||||
//===========================================================================
|
||||
//=============================Additional Features===========================
|
||||
//===========================================================================
|
||||
|
||||
// Custom M code points
|
||||
#define CUSTOM_M_CODES
|
||||
#ifdef CUSTOM_M_CODES
|
||||
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
|
||||
#define Z_PROBE_OFFSET_RANGE_MIN -15
|
||||
#define Z_PROBE_OFFSET_RANGE_MAX -5
|
||||
#endif
|
||||
|
||||
|
||||
// EEPROM
|
||||
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
|
||||
// M500 - stores parameters in EEPROM
|
||||
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
//define this to enable EEPROM support
|
||||
#define EEPROM_SETTINGS
|
||||
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
// please keep turned on if you can.
|
||||
//#define EEPROM_CHITCHAT
|
||||
|
||||
// Preheat Constants
|
||||
#define PLA_PREHEAT_HOTEND_TEMP 180
|
||||
#define PLA_PREHEAT_HPB_TEMP 70
|
||||
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
|
||||
#define ABS_PREHEAT_HOTEND_TEMP 240
|
||||
#define ABS_PREHEAT_HPB_TEMP 100
|
||||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
|
||||
//LCD and SD support
|
||||
//#define ULTRA_LCD //general LCD support, also 16x2
|
||||
//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
|
||||
#define SDSUPPORT // Enable SD Card Support in Hardware Console
|
||||
#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
|
||||
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
|
||||
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
|
||||
//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
|
||||
//#define ULTIPANEL //the UltiPanel as on Thingiverse
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
||||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
||||
|
||||
// The MaKr3d Makr-Panel with graphic controller and SD support
|
||||
// http://reprap.org/wiki/MaKr3d_MaKrPanel
|
||||
//#define MAKRPANEL
|
||||
|
||||
// The RepRapDiscount Smart Controller (white PCB)
|
||||
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
|
||||
//#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||||
|
||||
// The GADGETS3D G3D LCD/SD Controller (blue PCB)
|
||||
// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
|
||||
//#define G3D_PANEL
|
||||
|
||||
// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
||||
// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
|
||||
// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
|
||||
//#define REPRAPWORLD_KEYPAD
|
||||
//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click
|
||||
|
||||
// The Elefu RA Board Control Panel
|
||||
// http://www.elefu.com/index.php?route=product/product&product_id=53
|
||||
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARUDINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
||||
//#define RA_CONTROL_PANEL
|
||||
|
||||
//automatic expansion
|
||||
#if defined (MAKRPANEL)
|
||||
#define DOGLCD
|
||||
#define SDSUPPORT
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#define DEFAULT_LCD_CONTRAST 17
|
||||
#endif
|
||||
|
||||
#if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
||||
#define DOGLCD
|
||||
#define U8GLIB_ST7920
|
||||
#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||||
#endif
|
||||
|
||||
#if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
#if defined(REPRAPWORLD_KEYPAD)
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
#if defined(RA_CONTROL_PANEL)
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#define LCD_I2C_TYPE_PCA8574
|
||||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||||
#endif
|
||||
|
||||
//I2C PANELS
|
||||
|
||||
//#define LCD_I2C_SAINSMART_YWROBOT
|
||||
#ifdef LCD_I2C_SAINSMART_YWROBOT
|
||||
// This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )
|
||||
// Make sure it is placed in the Arduino libraries directory.
|
||||
#define LCD_I2C_TYPE_PCF8575
|
||||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
|
||||
//#define LCD_I2C_PANELOLU2
|
||||
#ifdef LCD_I2C_PANELOLU2
|
||||
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||||
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||||
// (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
|
||||
// Note: The PANELOLU2 encoder click input can either be directly connected to a pin
|
||||
// (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
|
||||
#define LCD_I2C_TYPE_MCP23017
|
||||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
|
||||
#ifndef ENCODER_PULSES_PER_STEP
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
#endif
|
||||
|
||||
#ifndef ENCODER_STEPS_PER_MENU_ITEM
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#endif
|
||||
|
||||
|
||||
#ifdef LCD_USE_I2C_BUZZER
|
||||
#define LCD_FEEDBACK_FREQUENCY_HZ 1000
|
||||
#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
||||
//#define LCD_I2C_VIKI
|
||||
#ifdef LCD_I2C_VIKI
|
||||
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||||
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||||
// Note: The pause/stop/resume LCD button pin should be connected to the Arduino
|
||||
// BTN_ENC pin (or set BTN_ENC to -1 if not used)
|
||||
#define LCD_I2C_TYPE_MCP23017
|
||||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
//#define SR_LCD
|
||||
#ifdef SR_LCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shift register
|
||||
//#define NEWPANEL
|
||||
#endif
|
||||
|
||||
|
||||
#ifdef ULTIPANEL
|
||||
// #define NEWPANEL //enable this if you have a click-encoder panel
|
||||
#define SDSUPPORT
|
||||
#define ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_HEIGHT 4
|
||||
#endif
|
||||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 16
|
||||
#define LCD_HEIGHT 2
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// default LCD contrast for dogm-like LCD displays
|
||||
#ifdef DOGLCD
|
||||
# ifndef DEFAULT_LCD_CONTRAST
|
||||
# define DEFAULT_LCD_CONTRAST 32
|
||||
# endif
|
||||
#endif
|
||||
|
||||
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||||
//#define FAST_PWM_FAN
|
||||
|
||||
// Temperature status LEDs that display the hotend and bet temperature.
|
||||
// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
|
||||
// Otherwise the RED led is on. There is 1C hysteresis.
|
||||
//#define TEMP_STAT_LEDS
|
||||
|
||||
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
|
||||
// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
|
||||
// is too low, you should also increment SOFT_PWM_SCALE.
|
||||
//#define FAN_SOFT_PWM
|
||||
|
||||
// Incrementing this by 1 will double the software PWM frequency,
|
||||
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
|
||||
// However, control resolution will be halved for each increment;
|
||||
// at zero value, there are 128 effective control positions.
|
||||
#define SOFT_PWM_SCALE 0
|
||||
|
||||
// M240 Triggers a camera by emulating a Canon RC-1 Remote
|
||||
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
||||
// #define PHOTOGRAPH_PIN 23
|
||||
|
||||
// SF send wrong arc g-codes when using Arc Point as fillet procedure
|
||||
//#define SF_ARC_FIX
|
||||
|
||||
// Support for the BariCUDA Paste Extruder.
|
||||
//#define BARICUDA
|
||||
|
||||
//define BlinkM/CyzRgb Support
|
||||
//#define BLINKM
|
||||
|
||||
/*********************************************************************\
|
||||
* R/C SERVO support
|
||||
* Sponsored by TrinityLabs, Reworked by codexmas
|
||||
**********************************************************************/
|
||||
|
||||
// Number of servos
|
||||
//
|
||||
// If you select a configuration below, this will receive a default value and does not need to be set manually
|
||||
// set it manually if you have more servos than extruders and wish to manually control some
|
||||
// leaving it undefined or defining as 0 will disable the servo subsystem
|
||||
// If unsure, leave commented / disabled
|
||||
//
|
||||
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
|
||||
|
||||
// Servo Endstops
|
||||
//
|
||||
// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
|
||||
// Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500.
|
||||
//
|
||||
|
||||
#define DIGIPOT_I2C
|
||||
|
||||
//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
|
||||
//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
|
||||
|
||||
#include "Configuration_adv.h"
|
||||
#include "thermistortables.h"
|
||||
|
||||
#endif //__CONFIGURATION_H
|
498
Marlin/example_configurations/makibox/Configuration_adv.h
Normal file
498
Marlin/example_configurations/makibox/Configuration_adv.h
Normal file
|
@ -0,0 +1,498 @@
|
|||
#ifndef CONFIGURATION_ADV_H
|
||||
#define CONFIGURATION_ADV_H
|
||||
|
||||
//===========================================================================
|
||||
//=============================Thermal Settings ============================
|
||||
//===========================================================================
|
||||
|
||||
#ifdef BED_LIMIT_SWITCHING
|
||||
#define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
|
||||
#endif
|
||||
#define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control
|
||||
|
||||
//// Heating sanity check:
|
||||
// This waits for the watch period in milliseconds whenever an M104 or M109 increases the target temperature
|
||||
// If the temperature has not increased at the end of that period, the target temperature is set to zero.
|
||||
// It can be reset with another M104/M109. This check is also only triggered if the target temperature and the current temperature
|
||||
// differ by at least 2x WATCH_TEMP_INCREASE
|
||||
//#define WATCH_TEMP_PERIOD 40000 //40 seconds
|
||||
//#define WATCH_TEMP_INCREASE 10 //Heat up at least 10 degree in 20 seconds
|
||||
|
||||
#ifdef PIDTEMP
|
||||
// this adds an experimental additional term to the heating power, proportional to the extrusion speed.
|
||||
// if Kc is chosen well, the additional required power due to increased melting should be compensated.
|
||||
#define PID_ADD_EXTRUSION_RATE
|
||||
#ifdef PID_ADD_EXTRUSION_RATE
|
||||
#define DEFAULT_Kc (1) //heating power=Kc*(e_speed)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
||||
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
|
||||
//The maximum buffered steps/sec of the extruder motor are called "se".
|
||||
//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
|
||||
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
|
||||
// you exit the value by any M109 without F*
|
||||
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
|
||||
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||
#define AUTOTEMP
|
||||
#ifdef AUTOTEMP
|
||||
#define AUTOTEMP_OLDWEIGHT 0.98
|
||||
#endif
|
||||
|
||||
//Show Temperature ADC value
|
||||
//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
|
||||
//#define SHOW_TEMP_ADC_VALUES
|
||||
|
||||
// extruder run-out prevention.
|
||||
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
|
||||
//#define EXTRUDER_RUNOUT_PREVENT
|
||||
#define EXTRUDER_RUNOUT_MINTEMP 190
|
||||
#define EXTRUDER_RUNOUT_SECONDS 30.
|
||||
#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
|
||||
#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
|
||||
#define EXTRUDER_RUNOUT_EXTRUDE 100
|
||||
|
||||
//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
|
||||
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
|
||||
#define TEMP_SENSOR_AD595_OFFSET 0.0
|
||||
#define TEMP_SENSOR_AD595_GAIN 1.0
|
||||
|
||||
//This is for controlling a fan to cool down the stepper drivers
|
||||
//it will turn on when any driver is enabled
|
||||
//and turn off after the set amount of seconds from last driver being disabled again
|
||||
#define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller (-1 to disable)
|
||||
#define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run
|
||||
#define CONTROLLERFAN_SPEED 255 // == full speed
|
||||
|
||||
// When first starting the main fan, run it at full speed for the
|
||||
// given number of milliseconds. This gets the fan spinning reliably
|
||||
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
|
||||
//#define FAN_KICKSTART_TIME 100
|
||||
|
||||
// Extruder cooling fans
|
||||
// Configure fan pin outputs to automatically turn on/off when the associated
|
||||
// extruder temperature is above/below EXTRUDER_AUTO_FAN_TEMPERATURE.
|
||||
// Multiple extruders can be assigned to the same pin in which case
|
||||
// the fan will turn on when any selected extruder is above the threshold.
|
||||
#define EXTRUDER_0_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_1_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_2_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
|
||||
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//=============================Mechanical Settings===========================
|
||||
//===========================================================================
|
||||
|
||||
#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
|
||||
|
||||
|
||||
//// AUTOSET LOCATIONS OF LIMIT SWITCHES
|
||||
//// Added by ZetaPhoenix 09-15-2012
|
||||
#ifdef MANUAL_HOME_POSITIONS // Use manual limit switch locations
|
||||
#define X_HOME_POS MANUAL_X_HOME_POS
|
||||
#define Y_HOME_POS MANUAL_Y_HOME_POS
|
||||
#define Z_HOME_POS MANUAL_Z_HOME_POS
|
||||
#else //Set min/max homing switch positions based upon homing direction and min/max travel limits
|
||||
//X axis
|
||||
#if X_HOME_DIR == -1
|
||||
#ifdef BED_CENTER_AT_0_0
|
||||
#define X_HOME_POS X_MAX_LENGTH * -0.5
|
||||
#else
|
||||
#define X_HOME_POS X_MIN_POS
|
||||
#endif //BED_CENTER_AT_0_0
|
||||
#else
|
||||
#ifdef BED_CENTER_AT_0_0
|
||||
#define X_HOME_POS X_MAX_LENGTH * 0.5
|
||||
#else
|
||||
#define X_HOME_POS X_MAX_POS
|
||||
#endif //BED_CENTER_AT_0_0
|
||||
#endif //X_HOME_DIR == -1
|
||||
|
||||
//Y axis
|
||||
#if Y_HOME_DIR == -1
|
||||
#ifdef BED_CENTER_AT_0_0
|
||||
#define Y_HOME_POS Y_MAX_LENGTH * -0.5
|
||||
#else
|
||||
#define Y_HOME_POS Y_MIN_POS
|
||||
#endif //BED_CENTER_AT_0_0
|
||||
#else
|
||||
#ifdef BED_CENTER_AT_0_0
|
||||
#define Y_HOME_POS Y_MAX_LENGTH * 0.5
|
||||
#else
|
||||
#define Y_HOME_POS Y_MAX_POS
|
||||
#endif //BED_CENTER_AT_0_0
|
||||
#endif //Y_HOME_DIR == -1
|
||||
|
||||
// Z axis
|
||||
#if Z_HOME_DIR == -1 //BED_CENTER_AT_0_0 not used
|
||||
#define Z_HOME_POS Z_MIN_POS
|
||||
#else
|
||||
#define Z_HOME_POS Z_MAX_POS
|
||||
#endif //Z_HOME_DIR == -1
|
||||
#endif //End auto min/max positions
|
||||
//END AUTOSET LOCATIONS OF LIMIT SWITCHES -ZP
|
||||
|
||||
|
||||
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
|
||||
|
||||
// A single Z stepper driver is usually used to drive 2 stepper motors.
|
||||
// Uncomment this define to utilize a separate stepper driver for each Z axis motor.
|
||||
// Only a few motherboards support this, like RAMPS, which have dual extruder support (the 2nd, often unused, extruder driver is used
|
||||
// to control the 2nd Z axis stepper motor). The pins are currently only defined for a RAMPS motherboards.
|
||||
// On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
|
||||
//#define Z_DUAL_STEPPER_DRIVERS
|
||||
|
||||
#ifdef Z_DUAL_STEPPER_DRIVERS
|
||||
#undef EXTRUDERS
|
||||
#define EXTRUDERS 1
|
||||
#endif
|
||||
|
||||
// Same again but for Y Axis.
|
||||
//#define Y_DUAL_STEPPER_DRIVERS
|
||||
|
||||
// Define if the two Y drives need to rotate in opposite directions
|
||||
#define INVERT_Y2_VS_Y_DIR true
|
||||
|
||||
#ifdef Y_DUAL_STEPPER_DRIVERS
|
||||
#undef EXTRUDERS
|
||||
#define EXTRUDERS 1
|
||||
#endif
|
||||
|
||||
#if defined (Z_DUAL_STEPPER_DRIVERS) && defined (Y_DUAL_STEPPER_DRIVERS)
|
||||
#error "You cannot have dual drivers for both Y and Z"
|
||||
#endif
|
||||
|
||||
// Enable this for dual x-carriage printers.
|
||||
// A dual x-carriage design has the advantage that the inactive extruder can be parked which
|
||||
// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
|
||||
// allowing faster printing speeds.
|
||||
//#define DUAL_X_CARRIAGE
|
||||
#ifdef DUAL_X_CARRIAGE
|
||||
// Configuration for second X-carriage
|
||||
// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
|
||||
// the second x-carriage always homes to the maximum endstop.
|
||||
#define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
|
||||
#define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
|
||||
#define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
|
||||
#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
|
||||
// However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software
|
||||
// override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
|
||||
// without modifying the firmware (through the "M218 T1 X???" command).
|
||||
// Remember: you should set the second extruder x-offset to 0 in your slicer.
|
||||
|
||||
// Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h)
|
||||
#define X2_ENABLE_PIN 29
|
||||
#define X2_STEP_PIN 25
|
||||
#define X2_DIR_PIN 23
|
||||
|
||||
// There are a few selectable movement modes for dual x-carriages using M605 S<mode>
|
||||
// Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
|
||||
// as long as it supports dual x-carriages. (M605 S0)
|
||||
// Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
|
||||
// that additional slicer support is not required. (M605 S1)
|
||||
// Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
|
||||
// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
|
||||
// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
|
||||
|
||||
// This is the default power-up mode which can be later using M605.
|
||||
#define DEFAULT_DUAL_X_CARRIAGE_MODE 0
|
||||
|
||||
// As the x-carriages are independent we can now account for any relative Z offset
|
||||
#define EXTRUDER1_Z_OFFSET 0.0 // z offset relative to extruder 0
|
||||
|
||||
// Default settings in "Auto-park Mode"
|
||||
#define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
|
||||
#define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
|
||||
|
||||
// Default x offset in duplication mode (typically set to half print bed width)
|
||||
#define DEFAULT_DUPLICATION_X_OFFSET 100
|
||||
|
||||
#endif //DUAL_X_CARRIAGE
|
||||
|
||||
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
|
||||
#define X_HOME_RETRACT_MM 5
|
||||
#define Y_HOME_RETRACT_MM 5
|
||||
#define Z_HOME_RETRACT_MM 2
|
||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||
|
||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||
|
||||
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
|
||||
|
||||
//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
|
||||
#define INVERT_X_STEP_PIN false
|
||||
#define INVERT_Y_STEP_PIN false
|
||||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
//default stepper release if idle
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min)
|
||||
#endif
|
||||
|
||||
//Comment to disable setting feedrate multiplier via encoder
|
||||
#ifdef ULTIPANEL
|
||||
#define ULTIPANEL_FEEDMULTIPLY
|
||||
#endif
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
#define DEFAULT_MINSEGMENTTIME 20000
|
||||
|
||||
// If defined the movements slow down when the look ahead buffer is only half full
|
||||
#define SLOWDOWN
|
||||
|
||||
// Frequency limit
|
||||
// See nophead's blog for more info
|
||||
// Not working O
|
||||
//#define XY_FREQUENCY_LIMIT 15
|
||||
|
||||
// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
|
||||
// of the buffer and all stops. This should not be much greater than zero and should only be changed
|
||||
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
|
||||
#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec)
|
||||
|
||||
// MS1 MS2 Stepper Driver Microstepping mode table
|
||||
#define MICROSTEP1 LOW,LOW
|
||||
#define MICROSTEP2 HIGH,LOW
|
||||
#define MICROSTEP4 LOW,HIGH
|
||||
#define MICROSTEP8 HIGH,HIGH
|
||||
#define MICROSTEP16 HIGH,HIGH
|
||||
|
||||
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
|
||||
#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
|
||||
|
||||
// Motor Current setting (Only functional when motor driver current ref pins are connected to a digital trimpot on supported boards)
|
||||
#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
|
||||
|
||||
// uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
|
||||
//#define DIGIPOT_I2C
|
||||
// Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
|
||||
#define DIGIPOT_I2C_NUM_CHANNELS 4
|
||||
// actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
|
||||
//#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}
|
||||
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.7, 1.7, 1.7, 1.7}
|
||||
|
||||
//===========================================================================
|
||||
//=============================Additional Features===========================
|
||||
//===========================================================================
|
||||
|
||||
//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
|
||||
#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
|
||||
#define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
|
||||
// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
|
||||
// using:
|
||||
//#define MENU_ADDAUTOSTART
|
||||
|
||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||
//#define USE_WATCHDOG
|
||||
|
||||
#ifdef USE_WATCHDOG
|
||||
// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
|
||||
// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
|
||||
// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
|
||||
//#define WATCHDOG_RESET_MANUAL
|
||||
#endif
|
||||
|
||||
// Enable the option to stop SD printing when hitting and endstops, needs to be enabled from the LCD menu when this option is enabled.
|
||||
//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
|
||||
|
||||
// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
|
||||
// it can e.g. be used to change z-positions in the print startup phase in real-time
|
||||
// does not respect endstops!
|
||||
//#define BABYSTEPPING
|
||||
#ifdef BABYSTEPPING
|
||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||
#define BABYSTEP_Z_MULTIPLICATOR 2 //faster z movements
|
||||
|
||||
#ifdef COREXY
|
||||
#error BABYSTEPPING not implemented for COREXY yet.
|
||||
#endif
|
||||
|
||||
#ifdef DELTA
|
||||
#ifdef BABYSTEP_XY
|
||||
#error BABYSTEPPING only implemented for Z axis on deltabots.
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// extruder advance constant (s2/mm3)
|
||||
//
|
||||
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
|
||||
//
|
||||
// Hooke's law says: force = k * distance
|
||||
// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
|
||||
// so: v ^ 2 is proportional to number of steps we advance the extruder
|
||||
//#define ADVANCE
|
||||
|
||||
#ifdef ADVANCE
|
||||
#define EXTRUDER_ADVANCE_K .0
|
||||
|
||||
#define D_FILAMENT 2.85
|
||||
#define STEPS_MM_E 836
|
||||
#define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
|
||||
#define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)
|
||||
|
||||
#endif // ADVANCE
|
||||
|
||||
// Arc interpretation settings:
|
||||
#define MM_PER_ARC_SEGMENT 1
|
||||
#define N_ARC_CORRECTION 25
|
||||
|
||||
const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
|
||||
|
||||
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
|
||||
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
|
||||
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
|
||||
// be commented out otherwise
|
||||
//#define SDCARDDETECTINVERTED
|
||||
|
||||
#ifdef ULTIPANEL
|
||||
#undef SDCARDDETECTINVERTED
|
||||
#endif
|
||||
|
||||
// Power Signal Control Definitions
|
||||
// By default use ATX definition
|
||||
#ifndef POWER_SUPPLY
|
||||
#define POWER_SUPPLY 1
|
||||
#endif
|
||||
// 1 = ATX
|
||||
#if (POWER_SUPPLY == 1)
|
||||
#define PS_ON_AWAKE LOW
|
||||
#define PS_ON_ASLEEP HIGH
|
||||
#endif
|
||||
// 2 = X-Box 360 203W
|
||||
#if (POWER_SUPPLY == 2)
|
||||
#define PS_ON_AWAKE HIGH
|
||||
#define PS_ON_ASLEEP LOW
|
||||
#endif
|
||||
|
||||
// Control heater 0 and heater 1 in parallel.
|
||||
//#define HEATERS_PARALLEL
|
||||
|
||||
//===========================================================================
|
||||
//=============================Buffers ============================
|
||||
//===========================================================================
|
||||
|
||||
// The number of linear motions that can be in the plan at any give time.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
|
||||
#if defined SDSUPPORT
|
||||
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
#else
|
||||
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
#endif
|
||||
|
||||
|
||||
//The ASCII buffer for receiving from the serial:
|
||||
#define MAX_CMD_SIZE 96
|
||||
#define BUFSIZE 4
|
||||
|
||||
|
||||
// Firmware based and LCD controlled retract
|
||||
// M207 and M208 can be used to define parameters for the retraction.
|
||||
// The retraction can be called by the slicer using G10 and G11
|
||||
// until then, intended retractions can be detected by moves that only extrude and the direction.
|
||||
// the moves are than replaced by the firmware controlled ones.
|
||||
|
||||
// #define FWRETRACT //ONLY PARTIALLY TESTED
|
||||
#ifdef FWRETRACT
|
||||
#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
|
||||
#define RETRACT_LENGTH 3 //default retract length (positive mm)
|
||||
#define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
|
||||
#define RETRACT_ZLIFT 0 //default retract Z-lift
|
||||
#define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
//adds support for experimental filament exchange support M600; requires display
|
||||
#ifdef ULTIPANEL
|
||||
#define FILAMENTCHANGEENABLE
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#define FILAMENTCHANGE_XPOS 3
|
||||
#define FILAMENTCHANGE_YPOS 3
|
||||
#define FILAMENTCHANGE_ZADD 10
|
||||
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
||||
#define FILAMENTCHANGE_FINALRETRACT -100
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#ifdef FILAMENTCHANGEENABLE
|
||||
#ifdef EXTRUDER_RUNOUT_PREVENT
|
||||
#error EXTRUDER_RUNOUT_PREVENT currently incompatible with FILAMENTCHANGE
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//============================= Define Defines ============================
|
||||
//===========================================================================
|
||||
#if EXTRUDERS > 1 && defined TEMP_SENSOR_1_AS_REDUNDANT
|
||||
#error "You cannot use TEMP_SENSOR_1_AS_REDUNDANT if EXTRUDERS > 1"
|
||||
#endif
|
||||
|
||||
#if EXTRUDERS > 1 && defined HEATERS_PARALLEL
|
||||
#error "You cannot use HEATERS_PARALLEL if EXTRUDERS > 1"
|
||||
#endif
|
||||
|
||||
#if TEMP_SENSOR_0 > 0
|
||||
#define THERMISTORHEATER_0 TEMP_SENSOR_0
|
||||
#define HEATER_0_USES_THERMISTOR
|
||||
#endif
|
||||
#if TEMP_SENSOR_1 > 0
|
||||
#define THERMISTORHEATER_1 TEMP_SENSOR_1
|
||||
#define HEATER_1_USES_THERMISTOR
|
||||
#endif
|
||||
#if TEMP_SENSOR_2 > 0
|
||||
#define THERMISTORHEATER_2 TEMP_SENSOR_2
|
||||
#define HEATER_2_USES_THERMISTOR
|
||||
#endif
|
||||
#if TEMP_SENSOR_BED > 0
|
||||
#define THERMISTORBED TEMP_SENSOR_BED
|
||||
#define BED_USES_THERMISTOR
|
||||
#endif
|
||||
#if TEMP_SENSOR_0 == -1
|
||||
#define HEATER_0_USES_AD595
|
||||
#endif
|
||||
#if TEMP_SENSOR_1 == -1
|
||||
#define HEATER_1_USES_AD595
|
||||
#endif
|
||||
#if TEMP_SENSOR_2 == -1
|
||||
#define HEATER_2_USES_AD595
|
||||
#endif
|
||||
#if TEMP_SENSOR_BED == -1
|
||||
#define BED_USES_AD595
|
||||
#endif
|
||||
#if TEMP_SENSOR_0 == -2
|
||||
#define HEATER_0_USES_MAX6675
|
||||
#endif
|
||||
#if TEMP_SENSOR_0 == 0
|
||||
#undef HEATER_0_MINTEMP
|
||||
#undef HEATER_0_MAXTEMP
|
||||
#endif
|
||||
#if TEMP_SENSOR_1 == 0
|
||||
#undef HEATER_1_MINTEMP
|
||||
#undef HEATER_1_MAXTEMP
|
||||
#endif
|
||||
#if TEMP_SENSOR_2 == 0
|
||||
#undef HEATER_2_MINTEMP
|
||||
#undef HEATER_2_MAXTEMP
|
||||
#endif
|
||||
#if TEMP_SENSOR_BED == 0
|
||||
#undef BED_MINTEMP
|
||||
#undef BED_MAXTEMP
|
||||
#endif
|
||||
|
||||
|
||||
#endif //__CONFIGURATION_ADV_H
|
|
@ -18,6 +18,8 @@
|
|||
// 9 Finnish
|
||||
// 10 Aragonese
|
||||
// 11 Dutch
|
||||
// 12 Catalan
|
||||
// 13 Basque-Euskera
|
||||
|
||||
#ifndef LANGUAGE_CHOICE
|
||||
#define LANGUAGE_CHOICE 1 // Pick your language from the list above
|
||||
|
@ -34,6 +36,9 @@
|
|||
#elif MOTHERBOARD == 77
|
||||
#define MACHINE_NAME "3Drag"
|
||||
#define FIRMWARE_URL "http://3dprint.elettronicain.it/"
|
||||
#elif MOTHERBOARD == 88
|
||||
#define MACHINE_NAME "Makibox"
|
||||
#define FIRMWARE_URL "https://github.com/ErikZalm/Marlin/"
|
||||
#else
|
||||
#ifdef CUSTOM_MENDEL_NAME
|
||||
#define MACHINE_NAME CUSTOM_MENDEL_NAME
|
||||
|
@ -77,8 +82,18 @@
|
|||
#define MSG_AUTO_HOME "Auto home"
|
||||
#define MSG_SET_ORIGIN "Set origin"
|
||||
#define MSG_PREHEAT_PLA "Preheat PLA"
|
||||
#define MSG_PREHEAT_PLA0 "Preheat PLA 1"
|
||||
#define MSG_PREHEAT_PLA1 "Preheat PLA 2"
|
||||
#define MSG_PREHEAT_PLA2 "Preheat PLA 3"
|
||||
#define MSG_PREHEAT_PLA012 "Preheat PLA All"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "Preheat PLA Bed"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "Preheat PLA conf"
|
||||
#define MSG_PREHEAT_ABS "Preheat ABS"
|
||||
#define MSG_PREHEAT_ABS0 "Preheat ABS 1"
|
||||
#define MSG_PREHEAT_ABS1 "Preheat ABS 2"
|
||||
#define MSG_PREHEAT_ABS2 "Preheat ABS 3"
|
||||
#define MSG_PREHEAT_ABS012 "Preheat ABS All"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "Preheat ABS Bed"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "Preheat ABS conf"
|
||||
#define MSG_COOLDOWN "Cooldown"
|
||||
#define MSG_SWITCH_PS_ON "Switch power on"
|
||||
|
@ -90,6 +105,8 @@
|
|||
#define MSG_MOVE_Y "Move Y"
|
||||
#define MSG_MOVE_Z "Move Z"
|
||||
#define MSG_MOVE_E "Extruder"
|
||||
#define MSG_MOVE_E1 "Extruder2"
|
||||
#define MSG_MOVE_E2 "Extruder3"
|
||||
#define MSG_MOVE_01MM "Move 0.1mm"
|
||||
#define MSG_MOVE_1MM "Move 1mm"
|
||||
#define MSG_MOVE_10MM "Move 10mm"
|
||||
|
@ -154,10 +171,10 @@
|
|||
#define MSG_KILLED "KILLED. "
|
||||
#define MSG_STOPPED "STOPPED. "
|
||||
#define MSG_CONTROL_RETRACT "Retract mm"
|
||||
#define MSG_CONTROL_RETRACTF "Retract F"
|
||||
#define MSG_CONTROL_RETRACTF "Retract V"
|
||||
#define MSG_CONTROL_RETRACT_ZLIFT "Hop mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet V"
|
||||
#define MSG_AUTORETRACT "AutoRetr."
|
||||
#define MSG_FILAMENTCHANGE "Change filament"
|
||||
#define MSG_INIT_SDCARD "Init. SD card"
|
||||
|
@ -251,7 +268,6 @@
|
|||
|
||||
#if LANGUAGE_CHOICE == 2
|
||||
|
||||
|
||||
// LCD Menu Messages
|
||||
// Please note these are limited to 17 characters!
|
||||
|
||||
|
@ -264,8 +280,18 @@
|
|||
#define MSG_AUTO_HOME "Auto. poz. zerowa"
|
||||
#define MSG_SET_ORIGIN "Ustaw punkt zero"
|
||||
#define MSG_PREHEAT_PLA "Rozgrzej PLA"
|
||||
#define MSG_PREHEAT_PLA0 "Rozgrzej PLA 1"
|
||||
#define MSG_PREHEAT_PLA1 "Rozgrzej PLA 2"
|
||||
#define MSG_PREHEAT_PLA2 "Rozgrzej PLA 3"
|
||||
#define MSG_PREHEAT_PLA012 "Roz. PLA Wszystko"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "Rozgrzej PLA Loze"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "Ustaw. rozg. PLA"
|
||||
#define MSG_PREHEAT_ABS "Rozgrzej ABS"
|
||||
#define MSG_PREHEAT_ABS0 "Rozgrzej ABS 1"
|
||||
#define MSG_PREHEAT_ABS1 "Rozgrzej ABS 2"
|
||||
#define MSG_PREHEAT_ABS2 "Rozgrzej ABS 3"
|
||||
#define MSG_PREHEAT_ABS012 "Roz. ABS Wszystko"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "Rozgrzej ABS Loze"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "Ustaw. rozg. ABS"
|
||||
#define MSG_COOLDOWN "Chlodzenie"
|
||||
#define MSG_SWITCH_PS_ON "Wlacz zasilacz"
|
||||
|
@ -277,6 +303,8 @@
|
|||
#define MSG_MOVE_Y "Przesun w Y"
|
||||
#define MSG_MOVE_Z "Przesun w Z"
|
||||
#define MSG_MOVE_E "Ekstruzja (os E)"
|
||||
#define MSG_MOVE_E1 "Extruder2"
|
||||
#define MSG_MOVE_E2 "Extruder3"
|
||||
#define MSG_MOVE_01MM "Przesuwaj co .1mm"
|
||||
#define MSG_MOVE_1MM "Przesuwaj co 1mm"
|
||||
#define MSG_MOVE_10MM "Przesuwaj co 10mm"
|
||||
|
@ -343,10 +371,10 @@
|
|||
#define MSG_STOPPED "Zatrzymany. "
|
||||
#define MSG_STEPPER_RELEASED "Zwolniony."
|
||||
#define MSG_CONTROL_RETRACT "Wycofaj mm"
|
||||
#define MSG_CONTROL_RETRACTF "Wycofaj F"
|
||||
#define MSG_CONTROL_RETRACTF "Wycofaj V"
|
||||
#define MSG_CONTROL_RETRACT_ZLIFT "Skok Z mm:"
|
||||
#define MSG_CONTROL_RETRACT_RECOVER "Cof. wycof. +mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "Cof. wycof. F"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "Cof. wycof. V"
|
||||
#define MSG_AUTORETRACT "Auto. wycofanie"
|
||||
#define MSG_FILAMENTCHANGE "Zmien filament"
|
||||
#define MSG_INIT_SDCARD "Inicjal. karty SD"
|
||||
|
@ -453,8 +481,18 @@
|
|||
#define MSG_AUTO_HOME "Home auto."
|
||||
#define MSG_SET_ORIGIN "Regler origine"
|
||||
#define MSG_PREHEAT_PLA " Prechauffage PLA"
|
||||
#define MSG_PREHEAT_PLA0 "Prechauff. PLA 1"
|
||||
#define MSG_PREHEAT_PLA1 "Prechauff. PLA 2"
|
||||
#define MSG_PREHEAT_PLA2 "Prechauff. PLA 3"
|
||||
#define MSG_PREHEAT_PLA012 "Prech. PLA Tout"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "Prech. PLA Plateau"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "Regl. prech. PLA"
|
||||
#define MSG_PREHEAT_ABS "Prechauffage ABS"
|
||||
#define MSG_PREHEAT_ABS0 "Prechauff. ABS 1"
|
||||
#define MSG_PREHEAT_ABS1 "Prechauff. ABS 2"
|
||||
#define MSG_PREHEAT_ABS2 "Prechauff. ABS 3"
|
||||
#define MSG_PREHEAT_ABS012 "Prech. ABS Tout"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "Prech. ABS Plateau"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "Regl. prech. ABS"
|
||||
#define MSG_COOLDOWN "Refroidir"
|
||||
#define MSG_SWITCH_PS_ON "Allumer alim."
|
||||
|
@ -468,6 +506,8 @@
|
|||
#define MSG_MOVE_Y "Move Y"
|
||||
#define MSG_MOVE_Z "Move Z"
|
||||
#define MSG_MOVE_E "Extruder"
|
||||
#define MSG_MOVE_E1 "Extruder2"
|
||||
#define MSG_MOVE_E2 "Extruder3"
|
||||
#define MSG_MOVE_01MM "Move 0.1mm"
|
||||
#define MSG_MOVE_1MM "Move 1mm"
|
||||
#define MSG_MOVE_10MM "Move 10mm"
|
||||
|
@ -532,10 +572,10 @@
|
|||
#define MSG_STOPPED "STOPPE."
|
||||
#define MSG_STEPPER_RELEASED "RELACHE."
|
||||
#define MSG_CONTROL_RETRACT "Retraction mm"
|
||||
#define MSG_CONTROL_RETRACTF "Retraction F"
|
||||
#define MSG_CONTROL_RETRACTF "Retraction V"
|
||||
#define MSG_CONTROL_RETRACT_ZLIFT "Hop mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet V"
|
||||
#define MSG_AUTORETRACT "Retract. Auto."
|
||||
#define MSG_FILAMENTCHANGE "Changer filament"
|
||||
#define MSG_INIT_SDCARD "Init. la carte SD"
|
||||
|
@ -643,8 +683,18 @@
|
|||
#define MSG_AUTO_HOME "Auto Nullpunkt"
|
||||
#define MSG_SET_ORIGIN "Setze Nullpunkt"
|
||||
#define MSG_PREHEAT_PLA "Vorwärmen PLA"
|
||||
#define MSG_PREHEAT_PLA0 "Vorwärmen PLA 1"
|
||||
#define MSG_PREHEAT_PLA1 "Vorwärmen PLA 2"
|
||||
#define MSG_PREHEAT_PLA2 "Vorwärmen PLA 3"
|
||||
#define MSG_PREHEAT_PLA012 "Vorw. PLA Alle"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "Vorw. PLA Bett"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "Vorwärm. PLA Ein."
|
||||
#define MSG_PREHEAT_ABS "Vorwärmen ABS"
|
||||
#define MSG_PREHEAT_ABS0 "Vorwärmen ABS 1"
|
||||
#define MSG_PREHEAT_ABS1 "Vorwärmen ABS 2"
|
||||
#define MSG_PREHEAT_ABS2 "Vorwärmen ABS 3"
|
||||
#define MSG_PREHEAT_ABS012 "Vorw. ABS Alle"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "Vorw. ABS Bett"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "Vorwärm. ABS Ein."
|
||||
#define MSG_COOLDOWN "Abkühlen"
|
||||
#define MSG_SWITCH_PS_ON "Switch Power On"
|
||||
|
@ -656,6 +706,8 @@
|
|||
#define MSG_MOVE_Y "Y bewegen"
|
||||
#define MSG_MOVE_Z "Z bewegen"
|
||||
#define MSG_MOVE_E "Extruder"
|
||||
#define MSG_MOVE_E1 "Extruder2"
|
||||
#define MSG_MOVE_E2 "Extruder3"
|
||||
#define MSG_MOVE_01MM "0.1mm bewegen"
|
||||
#define MSG_MOVE_1MM "1mm bewegen"
|
||||
#define MSG_MOVE_10MM "10mm bewegen"
|
||||
|
@ -722,10 +774,10 @@
|
|||
#define MSG_STOPPED "GESTOPPT"
|
||||
#define MSG_STEPPER_RELEASED "Stepper frei"
|
||||
#define MSG_CONTROL_RETRACT "Retract mm"
|
||||
#define MSG_CONTROL_RETRACTF "Retract F"
|
||||
#define MSG_CONTROL_RETRACTF "Retract V"
|
||||
#define MSG_CONTROL_RETRACT_ZLIFT "Hop mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet V"
|
||||
#define MSG_AUTORETRACT "AutoRetr."
|
||||
#define MSG_FILAMENTCHANGE "Filament wechseln"
|
||||
#define MSG_INIT_SDCARD "Init. SD-Card"
|
||||
|
@ -832,8 +884,18 @@
|
|||
#define MSG_AUTO_HOME "Llevar al origen"
|
||||
#define MSG_SET_ORIGIN "Establecer cero"
|
||||
#define MSG_PREHEAT_PLA "Precalentar PLA"
|
||||
#define MSG_PREHEAT_PLA0 "Precalentar PLA 1"
|
||||
#define MSG_PREHEAT_PLA1 "Precalentar PLA 2"
|
||||
#define MSG_PREHEAT_PLA2 "Precalentar PLA 3"
|
||||
#define MSG_PREHEAT_PLA012 "Precal. PLA Todo"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "Precal. PLA Base"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "Ajustar temp. PLA"
|
||||
#define MSG_PREHEAT_ABS "Precalentar ABS"
|
||||
#define MSG_PREHEAT_ABS0 "Precalentar ABS 1"
|
||||
#define MSG_PREHEAT_ABS1 "Precalentar ABS 2"
|
||||
#define MSG_PREHEAT_ABS2 "Precalentar ABS 3"
|
||||
#define MSG_PREHEAT_ABS012 "Precal. ABS Todo"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "Precal. ABS Base"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "Ajustar temp. ABS"
|
||||
#define MSG_COOLDOWN "Enfriar"
|
||||
#define MSG_SWITCH_PS_ON "Switch Power On"
|
||||
|
@ -841,13 +903,15 @@
|
|||
#define MSG_EXTRUDE "Extruir"
|
||||
#define MSG_RETRACT "Retraer"
|
||||
#define MSG_MOVE_AXIS "Mover ejes"
|
||||
#define MSG_MOVE_X "Move X"
|
||||
#define MSG_MOVE_Y "Move Y"
|
||||
#define MSG_MOVE_Z "Move Z"
|
||||
#define MSG_MOVE_E "Extruder"
|
||||
#define MSG_MOVE_01MM "Move 0.1mm"
|
||||
#define MSG_MOVE_1MM "Move 1mm"
|
||||
#define MSG_MOVE_10MM "Move 10mm"
|
||||
#define MSG_MOVE_X "Mover X"
|
||||
#define MSG_MOVE_Y "Mover Y"
|
||||
#define MSG_MOVE_Z "Mover Z"
|
||||
#define MSG_MOVE_E "Extrusor"
|
||||
#define MSG_MOVE_E1 "Extrusor2"
|
||||
#define MSG_MOVE_E2 "Extrusor3"
|
||||
#define MSG_MOVE_01MM "Mover 0.1mm"
|
||||
#define MSG_MOVE_1MM "Mover 1mm"
|
||||
#define MSG_MOVE_10MM "Mover 10mm"
|
||||
#define MSG_SPEED "Velocidad"
|
||||
#define MSG_NOZZLE "Nozzle"
|
||||
#define MSG_NOZZLE1 "Nozzle2"
|
||||
|
@ -908,12 +972,12 @@
|
|||
#define MSG_KILLED "PARADA DE EMERG."
|
||||
#define MSG_STOPPED "PARADA"
|
||||
#define MSG_CONTROL_RETRACT "Retraer mm"
|
||||
#define MSG_CONTROL_RETRACTF "Retraer F"
|
||||
#define MSG_CONTROL_RETRACTF "Retraer V"
|
||||
#define MSG_CONTROL_RETRACT_ZLIFT "Levantar mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVER "DesRet +mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "DesRet F"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "DesRet V"
|
||||
#define MSG_AUTORETRACT "AutoRetr."
|
||||
#define MSG_FILAMENTCHANGE "Change filament"
|
||||
#define MSG_FILAMENTCHANGE "Cambiar filamento"
|
||||
#define MSG_INIT_SDCARD "Iniciando tarjeta"
|
||||
#define MSG_CNG_SDCARD "Cambiar tarjeta"
|
||||
#define MSG_RECTRACT_WIDE "Retraer"
|
||||
|
@ -969,7 +1033,7 @@
|
|||
#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID "\n"
|
||||
#define MSG_COUNT_X " Cuenta X:"
|
||||
#define MSG_ERR_KILLED "¡¡Impresora Parada con kill()!!"
|
||||
#define MSG_ERR_STOPPED "¡Impresora parada por errores. Arregle el error y use M999 Para reiniciar!. (La temperatura se reestablece. Ajustela antes de continuar)"
|
||||
#define MSG_ERR_STOPPED "¡Impresora parada por errores. Arregle el error y use M999 Para reiniciar!. (La temperatura se reestablece. Ajustela despues de continuar)"
|
||||
#define MSG_RESEND "Reenviar:"
|
||||
#define MSG_UNKNOWN_COMMAND "Comando Desconocido:\""
|
||||
#define MSG_ACTIVE_EXTRUDER "Extrusor Activo: "
|
||||
|
@ -1026,8 +1090,18 @@
|
|||
#define MSG_AUTO_HOME "Парковка"
|
||||
#define MSG_SET_ORIGIN "Запомнить ноль"
|
||||
#define MSG_PREHEAT_PLA "Преднагрев PLA"
|
||||
#define MSG_PREHEAT_PLA0 "Преднагрев PLA0"
|
||||
#define MSG_PREHEAT_PLA1 "Преднагрев PLA1"
|
||||
#define MSG_PREHEAT_PLA2 "Преднагрев PLA2"
|
||||
#define MSG_PREHEAT_PLA012 "Преднаг. PLA все"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "Пред. PLA Кровать"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "Настройки PLA"
|
||||
#define MSG_PREHEAT_ABS "Преднагрев ABS"
|
||||
#define MSG_PREHEAT_ABS0 "Преднагрев ABS0"
|
||||
#define MSG_PREHEAT_ABS1 "Преднагрев ABS1"
|
||||
#define MSG_PREHEAT_ABS2 "Преднагрев ABS2"
|
||||
#define MSG_PREHEAT_ABS012 "Преднаг. ABS все "
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "Пред. ABS Кровать"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "Настройки ABS"
|
||||
#define MSG_COOLDOWN "Охлаждение"
|
||||
#define MSG_SWITCH_PS_ON "Switch Power On"
|
||||
|
@ -1039,6 +1113,8 @@
|
|||
#define MSG_MOVE_Y "Move Y"
|
||||
#define MSG_MOVE_Z "Move Z"
|
||||
#define MSG_MOVE_E "Extruder"
|
||||
#define MSG_MOVE_E1 "Extruder2"
|
||||
#define MSG_MOVE_E2 "Extruder3"
|
||||
#define MSG_MOVE_01MM "Move 0.1mm"
|
||||
#define MSG_MOVE_1MM "Move 1mm"
|
||||
#define MSG_MOVE_10MM "Move 10mm"
|
||||
|
@ -1091,8 +1167,8 @@
|
|||
#define MSG_WATCH "Обзор \003"
|
||||
#define MSG_PREPARE "Действия \x7E"
|
||||
#define MSG_TUNE "Настройки \x7E"
|
||||
#define MSG_RESUME_PRINT "Продолжить печать"
|
||||
#define MSG_RESUME_PRINT "Продолжить печать"
|
||||
#define MSG_PAUSE_PRINT "Продолжить печать"
|
||||
#define MSG_RESUME_PRINT "возобн. печать"
|
||||
#define MSG_STOP_PRINT "Остановить печать"
|
||||
#define MSG_CARD_MENU "Меню карты \x7E"
|
||||
#define MSG_NO_CARD "Нет карты"
|
||||
|
@ -1103,10 +1179,10 @@
|
|||
#define MSG_KILLED "УБИТО."
|
||||
#define MSG_STOPPED "ОСТАНОВЛЕНО."
|
||||
#define MSG_CONTROL_RETRACT "Откат mm:"
|
||||
#define MSG_CONTROL_RETRACTF "Откат F:"
|
||||
#define MSG_CONTROL_RETRACTF "Откат V:"
|
||||
#define MSG_CONTROL_RETRACT_ZLIFT "Прыжок mm:"
|
||||
#define MSG_CONTROL_RETRACT_RECOVER "Возврат +mm:"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "Возврат F:"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "Возврат V:"
|
||||
#define MSG_AUTORETRACT "АвтоОткат:"
|
||||
#define MSG_FILAMENTCHANGE "Change filament"
|
||||
#define MSG_INIT_SDCARD "Init. SD-Card"
|
||||
|
@ -1211,8 +1287,18 @@
|
|||
#define MSG_AUTO_HOME "Auto Home"
|
||||
#define MSG_SET_ORIGIN "Imposta Origine"
|
||||
#define MSG_PREHEAT_PLA "Preriscalda PLA"
|
||||
#define MSG_PREHEAT_PLA0 "Preriscalda PLA 1"
|
||||
#define MSG_PREHEAT_PLA1 "Preriscalda PLA 2"
|
||||
#define MSG_PREHEAT_PLA2 "Preriscalda PLA 3"
|
||||
#define MSG_PREHEAT_PLA012 "Preris. PLA Tutto"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "Preri. PLA Piatto"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "Preris. PLA Conf"
|
||||
#define MSG_PREHEAT_ABS "Preriscalda ABS"
|
||||
#define MSG_PREHEAT_ABS0 "Preriscalda ABS 1"
|
||||
#define MSG_PREHEAT_ABS1 "Preriscalda ABS 2"
|
||||
#define MSG_PREHEAT_ABS2 "Preriscalda ABS 3"
|
||||
#define MSG_PREHEAT_ABS012 "Preris. ABS Tutto"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "Preri. ABS Piatto"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "Preris. ABS Conf"
|
||||
#define MSG_COOLDOWN "Raffredda"
|
||||
#define MSG_SWITCH_PS_ON "Switch Power On"
|
||||
|
@ -1224,6 +1310,8 @@
|
|||
#define MSG_MOVE_Y "Move Y"
|
||||
#define MSG_MOVE_Z "Move Z"
|
||||
#define MSG_MOVE_E "Extruder"
|
||||
#define MSG_MOVE_E1 "Extruder2"
|
||||
#define MSG_MOVE_E2 "Extruder3"
|
||||
#define MSG_MOVE_01MM "Move 0.1mm"
|
||||
#define MSG_MOVE_1MM "Move 1mm"
|
||||
#define MSG_MOVE_10MM "Move 10mm"
|
||||
|
@ -1288,10 +1376,10 @@
|
|||
#define MSG_KILLED "UCCISO. "
|
||||
#define MSG_STOPPED "ARRESTATO. "
|
||||
#define MSG_CONTROL_RETRACT "Ritrai mm"
|
||||
#define MSG_CONTROL_RETRACTF "Ritrai F"
|
||||
#define MSG_CONTROL_RETRACTF "Ritrai V"
|
||||
#define MSG_CONTROL_RETRACT_ZLIFT "Salta mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet V"
|
||||
#define MSG_AUTORETRACT "AutoArretramento"
|
||||
#define MSG_FILAMENTCHANGE "Cambia filamento"
|
||||
#define MSG_INIT_SDCARD "Iniz. SD-Card"
|
||||
|
@ -1398,8 +1486,18 @@
|
|||
#define MSG_AUTO_HOME "Ir para origen"
|
||||
#define MSG_SET_ORIGIN "Estabelecer orig."
|
||||
#define MSG_PREHEAT_PLA "Pre-aquecer PLA"
|
||||
#define MSG_PREHEAT_PLA0 " pre-aquecer PLA 1"
|
||||
#define MSG_PREHEAT_PLA1 " pre-aquecer PLA 2"
|
||||
#define MSG_PREHEAT_PLA2 " pre-aquecer PLA 3"
|
||||
#define MSG_PREHEAT_PLA012 " pre-aq. PLA Tudo"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY " pre-aq. PLA \002Base"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "PLA setting"
|
||||
#define MSG_PREHEAT_ABS "Pre-aquecer ABS"
|
||||
#define MSG_PREHEAT_ABS0 " pre-aquecer ABS 1"
|
||||
#define MSG_PREHEAT_ABS1 " pre-aquecer ABS 2"
|
||||
#define MSG_PREHEAT_ABS2 " pre-aquecer ABS 3"
|
||||
#define MSG_PREHEAT_ABS012 " pre-aq. ABS Tudo"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY " pre-aq. ABS \002Base"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "ABS setting"
|
||||
#define MSG_COOLDOWN "Esfriar"
|
||||
#define MSG_SWITCH_PS_ON "Switch Power On"
|
||||
|
@ -1413,6 +1511,8 @@
|
|||
#define MSG_MOVE_Y "Move Y"
|
||||
#define MSG_MOVE_Z "Move Z"
|
||||
#define MSG_MOVE_E "Extruder"
|
||||
#define MSG_MOVE_E1 "Extruder2"
|
||||
#define MSG_MOVE_E2 "Extruder3"
|
||||
#define MSG_MOVE_01MM "Move 0.1mm"
|
||||
#define MSG_MOVE_1MM "Move 1mm"
|
||||
#define MSG_MOVE_10MM "Move 10mm"
|
||||
|
@ -1481,10 +1581,10 @@
|
|||
#define MSG_STOPPED "PARADA. "
|
||||
#define MSG_STEPPER_RELEASED "Lancado."
|
||||
#define MSG_CONTROL_RETRACT " Retrair mm:"
|
||||
#define MSG_CONTROL_RETRACTF " Retrair F:"
|
||||
#define MSG_CONTROL_RETRACTF " Retrair V:"
|
||||
#define MSG_CONTROL_RETRACT_ZLIFT " Levantar mm:"
|
||||
#define MSG_CONTROL_RETRACT_RECOVER " DesRet +mm:"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF " DesRet F:"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF " DesRet V:"
|
||||
#define MSG_AUTORETRACT " AutoRetr.:"
|
||||
#define MSG_FILAMENTCHANGE "Change filament"
|
||||
#define MSG_INIT_SDCARD "Init. SD-Card"
|
||||
|
@ -1592,8 +1692,18 @@
|
|||
#define MSG_AUTO_HOME "Aja referenssiin"
|
||||
#define MSG_SET_ORIGIN "Aseta origo"
|
||||
#define MSG_PREHEAT_PLA "Esilammita PLA"
|
||||
#define MSG_PREHEAT_PLA0 "Esilammita PLA 1"
|
||||
#define MSG_PREHEAT_PLA1 "Esilammita PLA 2"
|
||||
#define MSG_PREHEAT_PLA2 "Esilammita PLA 3"
|
||||
#define MSG_PREHEAT_PLA012 "Esila. PLA Kaikki"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "Esila. PLA Alusta"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "Esilamm. PLA konf"
|
||||
#define MSG_PREHEAT_ABS "Esilammita ABS"
|
||||
#define MSG_PREHEAT_ABS0 "Esilammita ABS 1"
|
||||
#define MSG_PREHEAT_ABS1 "Esilammita ABS 2"
|
||||
#define MSG_PREHEAT_ABS2 "Esilammita ABS 3"
|
||||
#define MSG_PREHEAT_ABS012 "Esila. ABS Kaikki"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "Esila. ABS Alusta"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "Esilamm. ABS konf"
|
||||
#define MSG_COOLDOWN "Jaahdyta"
|
||||
#define MSG_SWITCH_PS_ON "Virta paalle"
|
||||
|
@ -1605,6 +1715,8 @@
|
|||
#define MSG_MOVE_Y "Move Y"
|
||||
#define MSG_MOVE_Z "Move Z"
|
||||
#define MSG_MOVE_E "Extruder"
|
||||
#define MSG_MOVE_E1 "Extruder2"
|
||||
#define MSG_MOVE_E2 "Extruder3"
|
||||
#define MSG_MOVE_01MM "Move 0.1mm"
|
||||
#define MSG_MOVE_1MM "Move 1mm"
|
||||
#define MSG_MOVE_10MM "Move 10mm"
|
||||
|
@ -1669,10 +1781,10 @@
|
|||
#define MSG_KILLED "KILLED. "
|
||||
#define MSG_STOPPED "STOPPED. "
|
||||
#define MSG_CONTROL_RETRACT "Veda mm"
|
||||
#define MSG_CONTROL_RETRACTF "Veda F"
|
||||
#define MSG_CONTROL_RETRACTF "Veda V"
|
||||
#define MSG_CONTROL_RETRACT_ZLIFT "Z mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVER "UnRet +mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet F"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "UnRet V"
|
||||
#define MSG_AUTORETRACT "AutoVeto."
|
||||
#define MSG_FILAMENTCHANGE "Change filament"
|
||||
#define MSG_INIT_SDCARD "Init. SD-Card"
|
||||
|
@ -1779,8 +1891,18 @@
|
|||
#define MSG_AUTO_HOME "Levar a l'orichen"
|
||||
#define MSG_SET_ORIGIN "Establir zero"
|
||||
#define MSG_PREHEAT_PLA "Precalentar PLA"
|
||||
#define MSG_PREHEAT_PLA0 "Precalentar PLA0"
|
||||
#define MSG_PREHEAT_PLA1 "Precalentar PLA1"
|
||||
#define MSG_PREHEAT_PLA2 "Precalentar PLA2"
|
||||
#define MSG_PREHEAT_PLA012 "Precalentar PLA a"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "Prec. PLA Base"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "Achustar tem. PLA"
|
||||
#define MSG_PREHEAT_ABS "Precalentar ABS"
|
||||
#define MSG_PREHEAT_ABS0 "Precalentar ABS0"
|
||||
#define MSG_PREHEAT_ABS1 "Precalentar ABS1"
|
||||
#define MSG_PREHEAT_ABS2 "Precalentar ABS2"
|
||||
#define MSG_PREHEAT_ABS012 "Precalentar ABS a"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "Prec. ABS Base"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "Achustar tem. ABS"
|
||||
#define MSG_COOLDOWN "Enfriar"
|
||||
#define MSG_SWITCH_PS_ON "Enchegar Fuent"
|
||||
|
@ -1792,6 +1914,8 @@
|
|||
#define MSG_MOVE_Y "Move Y"
|
||||
#define MSG_MOVE_Z "Move Z"
|
||||
#define MSG_MOVE_E "Extruder"
|
||||
#define MSG_MOVE_E1 "Extruder2"
|
||||
#define MSG_MOVE_E2 "Extruder3"
|
||||
#define MSG_MOVE_01MM "Move 0.1mm"
|
||||
#define MSG_MOVE_1MM "Move 1mm"
|
||||
#define MSG_MOVE_10MM "Move 10mm"
|
||||
|
@ -1972,8 +2096,18 @@
|
|||
#define MSG_AUTO_HOME "Auto home"
|
||||
#define MSG_SET_ORIGIN "Nulpunt instellen"
|
||||
#define MSG_PREHEAT_PLA "PLA voorverwarmen"
|
||||
#define MSG_PREHEAT_PLA0 "PLA voorverw. 0"
|
||||
#define MSG_PREHEAT_PLA1 "PLA voorverw. 1"
|
||||
#define MSG_PREHEAT_PLA2 "PLA voorverw. 2"
|
||||
#define MSG_PREHEAT_PLA012 "PLA voorverw. aan"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "PLA voorverw. Bed"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "PLA verw. conf"
|
||||
#define MSG_PREHEAT_ABS "ABS voorverwarmen"
|
||||
#define MSG_PREHEAT_ABS0 "ABS voorverw. 0"
|
||||
#define MSG_PREHEAT_ABS1 "ABS voorverw. 1"
|
||||
#define MSG_PREHEAT_ABS2 "ABS voorverw. 2"
|
||||
#define MSG_PREHEAT_ABS012 "ABS voorverw. aan"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "ABS voorverw. Bed"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "ABS verw. conf"
|
||||
#define MSG_COOLDOWN "Afkoelen"
|
||||
#define MSG_SWITCH_PS_ON "Stroom aan"
|
||||
|
@ -1985,6 +2119,8 @@
|
|||
#define MSG_MOVE_Y "Verplaats Y"
|
||||
#define MSG_MOVE_Z "Verplaats Z"
|
||||
#define MSG_MOVE_E "Extruder"
|
||||
#define MSG_MOVE_E1 "Extruder2"
|
||||
#define MSG_MOVE_E2 "Extruder3"
|
||||
#define MSG_MOVE_01MM "Verplaats 0.1mm"
|
||||
#define MSG_MOVE_1MM "Verplaats 1mm"
|
||||
#define MSG_MOVE_10MM "Verplaats 10mm"
|
||||
|
@ -1995,6 +2131,9 @@
|
|||
#define MSG_BED "Bed"
|
||||
#define MSG_FAN_SPEED "Fan snelheid"
|
||||
#define MSG_FLOW "Flow"
|
||||
#define MSG_FLOW0 "Flow 0"
|
||||
#define MSG_FLOW1 "Flow 1"
|
||||
#define MSG_FLOW2 "Flow 2"
|
||||
#define MSG_CONTROL "Control"
|
||||
#define MSG_MIN " \002 Min"
|
||||
#define MSG_MAX " \002 Max"
|
||||
|
@ -2087,6 +2226,7 @@
|
|||
#define MSG_M105_INVALID_EXTRUDER "M105 Ongeldige extruder "
|
||||
#define MSG_M200_INVALID_EXTRUDER "M200 Ongeldige extruder "
|
||||
#define MSG_M218_INVALID_EXTRUDER "M218 Ongeldige extruder "
|
||||
#define MSG_M221_INVALID_EXTRUDER "M221 Ongeldige extruder "
|
||||
#define MSG_ERR_NO_THERMISTORS "Geen thermistors - geen temperatuur"
|
||||
#define MSG_M109_INVALID_EXTRUDER "M109 Ongeldige extruder "
|
||||
#define MSG_HEATING "Opwarmen..."
|
||||
|
@ -2139,4 +2279,401 @@
|
|||
|
||||
#endif
|
||||
|
||||
|
||||
#if LANGUAGE_CHOICE == 12
|
||||
|
||||
// LCD Menu Messages
|
||||
|
||||
// Please note these are limited to 17 characters!
|
||||
|
||||
#define WELCOME_MSG MACHINE_NAME " preparada."
|
||||
#define MSG_SD_INSERTED "SD detectada."
|
||||
#define MSG_SD_REMOVED "SD expulsada."
|
||||
#define MSG_MAIN "Menu principal"
|
||||
#define MSG_AUTOSTART "Inici automatic"
|
||||
#define MSG_DISABLE_STEPPERS "Apagar motors"
|
||||
#define MSG_AUTO_HOME "Home global"
|
||||
#define MSG_SET_ORIGIN "Establir origen"
|
||||
#define MSG_PREHEAT_PLA "Preescalfar PLA"
|
||||
#define MSG_PREHEAT_PLA0 "Preescalfar PLA 1"
|
||||
#define MSG_PREHEAT_PLA1 "Preescalfar PLA 2"
|
||||
#define MSG_PREHEAT_PLA2 "Preescalfar PLA 3"
|
||||
#define MSG_PREHEAT_PLA012 "Preesc. tot PLA"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "Preesc. llit PLA"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "Configuració PLA"
|
||||
#define MSG_PREHEAT_ABS "Preescalfar ABS"
|
||||
#define MSG_PREHEAT_ABS0 "Preescalfar ABS 1"
|
||||
#define MSG_PREHEAT_ABS1 "Preescalfar ABS 2"
|
||||
#define MSG_PREHEAT_ABS2 "Preescalfar ABS 3"
|
||||
#define MSG_PREHEAT_ABS012 "Preesc. tot ABS"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "Preesc. llit ABS"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "Configuració ABS"
|
||||
#define MSG_COOLDOWN "Refredar"
|
||||
#define MSG_SWITCH_PS_ON "Switch power on"
|
||||
#define MSG_SWITCH_PS_OFF "Switch power off"
|
||||
#define MSG_EXTRUDE "Extruir"
|
||||
#define MSG_RETRACT "Refredar"
|
||||
#define MSG_MOVE_AXIS "Moure eixos"
|
||||
#define MSG_MOVE_X "Moure X"
|
||||
#define MSG_MOVE_Y "Moure Y"
|
||||
#define MSG_MOVE_Z "Moure Z"
|
||||
#define MSG_MOVE_E "Extrusor"
|
||||
#define MSG_MOVE_E1 "Extruder2"
|
||||
#define MSG_MOVE_E2 "Extruder3"
|
||||
#define MSG_MOVE_01MM "Moure 0.1mm"
|
||||
#define MSG_MOVE_1MM "Moure 1mm"
|
||||
#define MSG_MOVE_10MM "Moure 10mm"
|
||||
#define MSG_SPEED "Velocitat"
|
||||
#define MSG_NOZZLE "Nozzle"
|
||||
#define MSG_NOZZLE1 "Nozzle2"
|
||||
#define MSG_NOZZLE2 "Nozzle3"
|
||||
#define MSG_BED "Llit"
|
||||
#define MSG_FAN_SPEED "Vel. Ventilador"
|
||||
#define MSG_FLOW "Fluxe"
|
||||
#define MSG_FLOW0 "Fluxe 0"
|
||||
#define MSG_FLOW1 "Fluxe 1"
|
||||
#define MSG_FLOW2 "Fluxe 2"
|
||||
#define MSG_CONTROL "Control"
|
||||
#define MSG_MIN " \002 Min"
|
||||
#define MSG_MAX " \002 Max"
|
||||
#define MSG_FACTOR " \002 Fact"
|
||||
#define MSG_AUTOTEMP "Autotemp"
|
||||
#define MSG_ON "On "
|
||||
#define MSG_OFF "Off"
|
||||
#define MSG_PID_P "PID-P"
|
||||
#define MSG_PID_I "PID-I"
|
||||
#define MSG_PID_D "PID-D"
|
||||
#define MSG_PID_C "PID-C"
|
||||
#define MSG_ACC "Accel"
|
||||
#define MSG_VXY_JERK "Vxy-jerk"
|
||||
#define MSG_VZ_JERK "Vz-jerk"
|
||||
#define MSG_VE_JERK "Ve-jerk"
|
||||
#define MSG_VMAX "Vmax "
|
||||
#define MSG_X "x"
|
||||
#define MSG_Y "y"
|
||||
#define MSG_Z "z"
|
||||
#define MSG_E "e"
|
||||
#define MSG_VMIN "Vmin"
|
||||
#define MSG_VTRAV_MIN "VTrav min"
|
||||
#define MSG_AMAX "Amax "
|
||||
#define MSG_A_RETRACT "A-retract"
|
||||
#define MSG_XSTEPS "Xpassos/mm"
|
||||
#define MSG_YSTEPS "Ypassos/mm"
|
||||
#define MSG_ZSTEPS "Zpassos/mm"
|
||||
#define MSG_ESTEPS "Epassos/mm"
|
||||
#define MSG_RECTRACT "Retreure"
|
||||
#define MSG_TEMPERATURE "Temperatura"
|
||||
#define MSG_MOTION "Moviment"
|
||||
#define MSG_CONTRAST "Contrast de LCD"
|
||||
#define MSG_STORE_EPROM "Desar a memoria"
|
||||
#define MSG_LOAD_EPROM "Carregar de mem."
|
||||
#define MSG_RESTORE_FAILSAFE "Rest. emergencia"
|
||||
#define MSG_REFRESH "Refrescar"
|
||||
#define MSG_WATCH "Pantalla Info."
|
||||
#define MSG_PREPARE "Preparar"
|
||||
#define MSG_TUNE "Calibrar"
|
||||
#define MSG_PAUSE_PRINT "Pausa imp."
|
||||
#define MSG_RESUME_PRINT "Reprendre imp."
|
||||
#define MSG_STOP_PRINT "Parar inp."
|
||||
#define MSG_CARD_MENU "Imprimir de SD"
|
||||
#define MSG_NO_CARD "-Sense targeta SD"
|
||||
#define MSG_DWELL "Repos..."
|
||||
#define MSG_USERWAIT "Esperant usuari.."
|
||||
#define MSG_RESUMING "Reprenent imp."
|
||||
#define MSG_NO_MOVE "Sense moviment."
|
||||
#define MSG_KILLED "PARADA DE EMERG. "
|
||||
#define MSG_STOPPED "ATURAT. "
|
||||
#define MSG_CONTROL_RETRACT "Retreure mm"
|
||||
#define MSG_CONTROL_RETRACTF "Retreure F"
|
||||
#define MSG_CONTROL_RETRACT_ZLIFT "Aixecar mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVER "DesRet +mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "DesRet F"
|
||||
#define MSG_AUTORETRACT "AutoRetr."
|
||||
#define MSG_FILAMENTCHANGE "Canviar filament"
|
||||
#define MSG_INIT_SDCARD "Iniciant SD"
|
||||
#define MSG_CNG_SDCARD "Canviar SD"
|
||||
#define MSG_ZPROBE_OUT "Z probe out. bed"
|
||||
#define MSG_POSITION_UNKNOWN "Home X/Y abans Z"
|
||||
#define MSG_ZPROBE_ZOFFSET "Z Offset"
|
||||
#define MSG_BABYSTEP_X "Babystep X"
|
||||
#define MSG_BABYSTEP_Y "Babystep Y"
|
||||
#define MSG_BABYSTEP_Z "Babystep Z"
|
||||
#define MSG_ENDSTOP_ABORT "Endstop abort"
|
||||
|
||||
// Serial Console Messages
|
||||
|
||||
#define MSG_Enqueing "en cua \""
|
||||
#define MSG_POWERUP "PowerUp"
|
||||
#define MSG_EXTERNAL_RESET " Reset Extern"
|
||||
#define MSG_BROWNOUT_RESET " Reset per Voltatge Incorrecte"
|
||||
#define MSG_WATCHDOG_RESET " Reset per Bloqueix"
|
||||
#define MSG_SOFTWARE_RESET " Reset per Software"
|
||||
#define MSG_AUTHOR " | Author: "
|
||||
#define MSG_CONFIGURATION_VER "Ultima actualitzacio: "
|
||||
#define MSG_FREE_MEMORY " Memoria lliure: "
|
||||
#define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
|
||||
#define MSG_OK "ok"
|
||||
#define MSG_FILE_SAVED "Fitxer desat."
|
||||
#define MSG_ERR_LINE_NO "El Numero de la Linia no es igual al Ultimo Numero de Linia+1, Ultima Linia:"
|
||||
#define MSG_ERR_CHECKSUM_MISMATCH "el checksum no coincideix, Ultima Linia:"
|
||||
#define MSG_ERR_NO_CHECKSUM "No s'ha trobat el Checksum amb el numero de linea, Ultima Linea:"
|
||||
#define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "No s'ha trobat Numero de Linea amb el Checksum, Ultima Linea:"
|
||||
#define MSG_FILE_PRINTED "Impresio acabada"
|
||||
#define MSG_BEGIN_FILE_LIST "Inici de la llista d'arxius"
|
||||
#define MSG_END_FILE_LIST "Fi de la llista d'arxius"
|
||||
#define MSG_M104_INVALID_EXTRUDER "M104 Extrusor Invalid "
|
||||
#define MSG_M105_INVALID_EXTRUDER "M105 Extrusor Invalid "
|
||||
#define MSG_M200_INVALID_EXTRUDER "M200 Extrusor Invalid "
|
||||
#define MSG_M218_INVALID_EXTRUDER "M218 Extrusor Invalid "
|
||||
#define MSG_M221_INVALID_EXTRUDER "M221 Extrusor Invalid "
|
||||
#define MSG_ERR_NO_THERMISTORS "No hi ha termistors - sense temperatura"
|
||||
#define MSG_M109_INVALID_EXTRUDER "M109 Extrusor Invalid "
|
||||
#define MSG_HEATING "Escalfant..."
|
||||
#define MSG_HEATING_COMPLETE "Escalfament acabat."
|
||||
#define MSG_BED_HEATING "Escalfant llit."
|
||||
#define MSG_BED_DONE "Llit Calent."
|
||||
#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID "\n"
|
||||
#define MSG_COUNT_X " Count X: "
|
||||
#define MSG_ERR_KILLED "Impressora Parada per kill()!"
|
||||
#define MSG_ERR_STOPPED "Impressora Parada per errors. Repara l'error i utilitza M999 per reiniciar!. (Hi ha un reset de temperatura, cal ajustarla abans de continuuar)"
|
||||
#define MSG_RESEND "Reenviar: "
|
||||
#define MSG_UNKNOWN_COMMAND "Comanda Desconeguda: \""
|
||||
#define MSG_ACTIVE_EXTRUDER "Extrusor Actiu: "
|
||||
#define MSG_INVALID_EXTRUDER "Extrusor Invalid"
|
||||
#define MSG_X_MIN "x_min: "
|
||||
#define MSG_X_MAX "x_max: "
|
||||
#define MSG_Y_MIN "y_min: "
|
||||
#define MSG_Y_MAX "y_max: "
|
||||
#define MSG_Z_MIN "z_min: "
|
||||
#define MSG_Z_MAX "z_max: "
|
||||
#define MSG_M119_REPORT "Comprobant finals de carrera."
|
||||
#define MSG_ENDSTOP_HIT "Activat"
|
||||
#define MSG_ENDSTOP_OPEN "obert"
|
||||
#define MSG_HOTEND_OFFSET "Hotend offsets:"
|
||||
|
||||
#define MSG_SD_CANT_OPEN_SUBDIR "No s'ha pogut obrir la carpeta"
|
||||
#define MSG_SD_INIT_FAIL "Error al iniciar la SD"
|
||||
#define MSG_SD_VOL_INIT_FAIL "Error al montar el volum"
|
||||
#define MSG_SD_OPENROOT_FAIL "Error al obrir la carpeta arrel"
|
||||
#define MSG_SD_CARD_OK "Targeta SD OK"
|
||||
#define MSG_SD_WORKDIR_FAIL "Error al obrir la carpeta de treball"
|
||||
#define MSG_SD_OPEN_FILE_FAIL "Error al obrir, Fitxer: "
|
||||
#define MSG_SD_FILE_OPENED "Fitxer obert:"
|
||||
#define MSG_SD_SIZE " Mida: "
|
||||
#define MSG_SD_FILE_SELECTED "Fitxer Seleccionat"
|
||||
#define MSG_SD_WRITE_TO_FILE "Desant al fitxer: "
|
||||
#define MSG_SD_PRINTING_BYTE "SD imprimint el byte "
|
||||
#define MSG_SD_NOT_PRINTING "No s'està imprimint amb SD"
|
||||
#define MSG_SD_ERR_WRITE_TO_FILE "Error al esciure al fitxer"
|
||||
#define MSG_SD_CANT_ENTER_SUBDIR "No es pot obrir la carpeta: "
|
||||
|
||||
#define MSG_STEPPER_TOO_HIGH "Steprate massa alt: "
|
||||
#define MSG_ENDSTOPS_HIT "S'ha tocat el final de carrera: "
|
||||
#define MSG_ERR_COLD_EXTRUDE_STOP " extrusio freda evitada"
|
||||
#define MSG_ERR_LONG_EXTRUDE_STOP " extrusio massa llarga evitada"
|
||||
#define MSG_BABYSTEPPING_X "Babystepping X"
|
||||
#define MSG_BABYSTEPPING_Y "Babystepping Y"
|
||||
#define MSG_BABYSTEPPING_Z "Babystepping Z"
|
||||
#define MSG_SERIAL_ERROR_MENU_STRUCTURE "Error a l'estructura dels menus"
|
||||
|
||||
#endif
|
||||
|
||||
//Basque-Euskera
|
||||
#if LANGUAGE_CHOICE == 13
|
||||
|
||||
// LCD Menu Messages
|
||||
// Please note these are limited to 17 characters!
|
||||
|
||||
#define WELCOME_MSG MACHINE_NAME " prest."
|
||||
#define MSG_SD_INSERTED "Txartela sartuta"
|
||||
#define MSG_SD_REMOVED "Txartela kenduta"
|
||||
#define MSG_MAIN "Menu nagusia"
|
||||
#define MSG_AUTOSTART "Auto hasiera"
|
||||
#define MSG_DISABLE_STEPPERS "Itzali motoreak"
|
||||
#define MSG_AUTO_HOME "Hasierara joan"
|
||||
#define MSG_SET_ORIGIN "Hasiera ipini"
|
||||
#define MSG_PREHEAT_PLA "Aurreberotu PLA"
|
||||
#define MSG_PREHEAT_PLA0 "Aurreberotu PLA1"
|
||||
#define MSG_PREHEAT_PLA1 "Aurreberotu PLA2"
|
||||
#define MSG_PREHEAT_PLA2 "Aurreberotu PLA3"
|
||||
#define MSG_PREHEAT_PLA012 "Berotu PLA Guztia"
|
||||
#define MSG_PREHEAT_PLA_BEDONLY "Berotu PLA Ohea"
|
||||
#define MSG_PREHEAT_PLA_SETTINGS "Berotu PLA Konfig"
|
||||
#define MSG_PREHEAT_ABS "Aurreberotu ABS"
|
||||
#define MSG_PREHEAT_ABS0 "Aurreberotu ABS 1"
|
||||
#define MSG_PREHEAT_ABS1 "Aurreberotu ABS 2"
|
||||
#define MSG_PREHEAT_ABS2 "Aurreberotu ABS 3"
|
||||
#define MSG_PREHEAT_ABS012 "Berotu ABS Guztia"
|
||||
#define MSG_PREHEAT_ABS_BEDONLY "Berotu ABS Ohea"
|
||||
#define MSG_PREHEAT_ABS_SETTINGS "Berotu ABS Konfig"
|
||||
#define MSG_COOLDOWN "Hoztu"
|
||||
#define MSG_SWITCH_PS_ON "Energia piztu"
|
||||
#define MSG_SWITCH_PS_OFF "Energia itzali"
|
||||
#define MSG_EXTRUDE "Estruitu"
|
||||
#define MSG_RETRACT "Atzera eragin"
|
||||
#define MSG_MOVE_AXIS "Ardatzak mugitu"
|
||||
#define MSG_MOVE_X "Mugitu X"
|
||||
#define MSG_MOVE_Y "Mugitu Y"
|
||||
#define MSG_MOVE_Z "Mugitu Z"
|
||||
#define MSG_MOVE_E "Estrusorea"
|
||||
#define MSG_MOVE_E1 "Estrusorea2"
|
||||
#define MSG_MOVE_E2 "Estrusorea3"
|
||||
#define MSG_MOVE_01MM "Mugitu 0.1mm"
|
||||
#define MSG_MOVE_1MM "Mugitu 1mm"
|
||||
#define MSG_MOVE_10MM "Mugitu 10mm"
|
||||
#define MSG_SPEED "Abiadura"
|
||||
#define MSG_NOZZLE "Pita"
|
||||
#define MSG_NOZZLE1 "Pita2"
|
||||
#define MSG_NOZZLE2 "Pita3"
|
||||
#define MSG_BED "Ohea"
|
||||
#define MSG_FAN_SPEED "Haizagailua"
|
||||
#define MSG_FLOW "Fluxua"
|
||||
#define MSG_FLOW0 "Fluxua 0"
|
||||
#define MSG_FLOW1 "Fluxua 1"
|
||||
#define MSG_FLOW2 "Fluxua 2"
|
||||
#define MSG_CONTROL "Kontrola"
|
||||
#define MSG_MIN " \002 Min"
|
||||
#define MSG_MAX " \002 Max"
|
||||
#define MSG_FACTOR " \002 Faktorea"
|
||||
#define MSG_AUTOTEMP "Auto tenperatura"
|
||||
#define MSG_ON "On "
|
||||
#define MSG_OFF "Off"
|
||||
#define MSG_PID_P "PID-P"
|
||||
#define MSG_PID_I "PID-I"
|
||||
#define MSG_PID_D "PID-D"
|
||||
#define MSG_PID_C "PID-C"
|
||||
#define MSG_ACC "Azelerazioa"
|
||||
#define MSG_VXY_JERK "Vxy-astindua"
|
||||
#define MSG_VZ_JERK "Vz-astindua"
|
||||
#define MSG_VE_JERK "Ve-astindua"
|
||||
#define MSG_VMAX "Vmax "
|
||||
#define MSG_X "x"
|
||||
#define MSG_Y "y"
|
||||
#define MSG_Z "z"
|
||||
#define MSG_E "e"
|
||||
#define MSG_VMIN "Vmin"
|
||||
#define MSG_VTRAV_MIN "VTrav min"
|
||||
#define MSG_AMAX "Amax "
|
||||
#define MSG_A_RETRACT "A-retrakt"
|
||||
#define MSG_XSTEPS "X pausoak/mm"
|
||||
#define MSG_YSTEPS "Y pausoak/mm"
|
||||
#define MSG_ZSTEPS "Z pausoak/mm"
|
||||
#define MSG_ESTEPS "E pausoak/mm"
|
||||
#define MSG_RECTRACT "Atzera eragin"
|
||||
#define MSG_TEMPERATURE "Tenperatura"
|
||||
#define MSG_MOTION "Mugimendua"
|
||||
#define MSG_CONTRAST "LCD kontrastea"
|
||||
#define MSG_STORE_EPROM "Gorde memoria"
|
||||
#define MSG_LOAD_EPROM "Kargatu memoria"
|
||||
#define MSG_RESTORE_FAILSAFE "Larri. berriz."
|
||||
#define MSG_REFRESH "Berriz kargatu"
|
||||
#define MSG_WATCH "Pantaila info"
|
||||
#define MSG_PREPARE "Prestatu"
|
||||
#define MSG_TUNE "Doitu"
|
||||
#define MSG_PAUSE_PRINT "Pausatu inprimak."
|
||||
#define MSG_RESUME_PRINT "Jarraitu inprima."
|
||||
#define MSG_STOP_PRINT "Gelditu inprima."
|
||||
#define MSG_CARD_MENU "SD-tik inprimatu"
|
||||
#define MSG_NO_CARD "Ez dago txartelik"
|
||||
#define MSG_DWELL "Lo egin..."
|
||||
#define MSG_USERWAIT "Aginduak zain..."
|
||||
#define MSG_RESUMING "Jarraitzen inpri."
|
||||
#define MSG_NO_MOVE "Mugimendu gabe"
|
||||
#define MSG_KILLED "LARRIALDI GELDIA"
|
||||
#define MSG_STOPPED "GELDITUTA. "
|
||||
#define MSG_CONTROL_RETRACT "Atzera egin mm"
|
||||
#define MSG_CONTROL_RETRACTF "Atzera egin V"
|
||||
#define MSG_CONTROL_RETRACT_ZLIFT "Igo mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVER "Atzera egin +mm"
|
||||
#define MSG_CONTROL_RETRACT_RECOVERF "Atzera egin V"
|
||||
#define MSG_AUTORETRACT "Atzera egin"
|
||||
#define MSG_FILAMENTCHANGE "Aldatu filament."
|
||||
#define MSG_INIT_SDCARD "Hasieratu txartela"
|
||||
#define MSG_CNG_SDCARD "Aldatu txartela"
|
||||
#define MSG_ZPROBE_OUT "Z ohe hasiera"
|
||||
#define MSG_POSITION_UNKNOWN "Posizio ezezaguna"
|
||||
#define MSG_ZPROBE_ZOFFSET "Z konpentsatu"
|
||||
#define MSG_BABYSTEP_X "Babystep X"
|
||||
#define MSG_BABYSTEP_Y "Babystep Y"
|
||||
#define MSG_BABYSTEP_Z "Babystep Z"
|
||||
#define MSG_ENDSTOP_ABORT "Endstop deuseztat"
|
||||
|
||||
// Serial Console Messages
|
||||
|
||||
#define MSG_Enqueing "Zerrendan \""
|
||||
#define MSG_POWERUP "Pizketa"
|
||||
#define MSG_EXTERNAL_RESET " Kanpoko Reset"
|
||||
#define MSG_BROWNOUT_RESET " Tentsio Okerra Reset"
|
||||
#define MSG_WATCHDOG_RESET " Reset Blokeoa"
|
||||
#define MSG_SOFTWARE_RESET " Software Reset"
|
||||
#define MSG_AUTHOR " | Egilea: "
|
||||
#define MSG_CONFIGURATION_VER " Azken Aktualizazio: "
|
||||
#define MSG_FREE_MEMORY " Aske Memoria: "
|
||||
#define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
|
||||
#define MSG_OK "ok"
|
||||
#define MSG_FILE_SAVED "Gordetuta."
|
||||
#define MSG_ERR_LINE_NO "Lerro zenbakia ez da azken zenbakia+1 berdina, Azken Lerroa: "
|
||||
#define MSG_ERR_CHECKSUM_MISMATCH "checksum-ak ez du aldiberekotasuna, Azken Lerroa: "
|
||||
#define MSG_ERR_NO_CHECKSUM "Ez da checksum-ik aurkitu lerro zenbakian, Azken Lerroa: "
|
||||
#define MSG_ERR_NO_LINENUMBER_WITH_CHECKSUM "Ez da lerro zenbakia aurkitu checksum-arekin, Azken Lerroa: "
|
||||
#define MSG_FILE_PRINTED "Inprimaketa bukatua"
|
||||
#define MSG_BEGIN_FILE_LIST "Hasi artxibo zerrenda"
|
||||
#define MSG_END_FILE_LIST "Amaitu artxibo zerrenda"
|
||||
#define MSG_M104_INVALID_EXTRUDER "M104 Balio gabeko Estrusorea "
|
||||
#define MSG_M105_INVALID_EXTRUDER "M105 Balio gabeko Estrusorea "
|
||||
#define MSG_M200_INVALID_EXTRUDER "M200 Balio gabeko Estrusorea "
|
||||
#define MSG_M218_INVALID_EXTRUDER "M218 Balio gabeko Estrusorea "
|
||||
#define MSG_M221_INVALID_EXTRUDER "M221 Balio gabeko Estrusorea "
|
||||
#define MSG_ERR_NO_THERMISTORS "Termistorerik ez dago - Tenperaturarik gabe"
|
||||
#define MSG_M109_INVALID_EXTRUDER "M109 Balio gabeko Estrusorea "
|
||||
#define MSG_HEATING "Berotzen..."
|
||||
#define MSG_HEATING_COMPLETE "berotuta."
|
||||
#define MSG_BED_HEATING "Ohea berotzen."
|
||||
#define MSG_BED_DONE "Ohea berotuta."
|
||||
#define MSG_M115_REPORT "FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:" FIRMWARE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID "\n"
|
||||
#define MSG_COUNT_X " X Kontu: "
|
||||
#define MSG_ERR_KILLED "Inprimagailua geldituta. kill() called!"
|
||||
#define MSG_ERR_STOPPED "Akatsen eraginez inprimagailua geldituta. Errorea konpondu eta M999 erabili berrabiarazteko. (Tenperatura galdu egin da. Berriro ipini)"
|
||||
#define MSG_RESEND "Bidali berriro: "
|
||||
#define MSG_UNKNOWN_COMMAND "Agindu ezezaguna: \""
|
||||
#define MSG_ACTIVE_EXTRUDER "Estrusore Aktiboa: "
|
||||
#define MSG_INVALID_EXTRUDER "Balio gabeko Estrusorea"
|
||||
#define MSG_X_MIN "x_min: "
|
||||
#define MSG_X_MAX "x_max: "
|
||||
#define MSG_Y_MIN "y_min: "
|
||||
#define MSG_Y_MAX "y_max: "
|
||||
#define MSG_Z_MIN "z_min: "
|
||||
#define MSG_Z_MAX "z_max: "
|
||||
#define MSG_M119_REPORT "Bide amaiera egiaztatzen"
|
||||
#define MSG_ENDSTOP_HIT "Sakatuta"
|
||||
#define MSG_ENDSTOP_OPEN "irekia"
|
||||
#define MSG_HOTEND_OFFSET "Hotend offsets:"
|
||||
|
||||
#define MSG_SD_CANT_OPEN_SUBDIR "Azpidirektorio ezin da ireki"
|
||||
#define MSG_SD_INIT_FAIL "Akatsa txartela hasterakoan"
|
||||
#define MSG_SD_VOL_INIT_FAIL "Akatsa partizioa hasterakoan"
|
||||
#define MSG_SD_OPENROOT_FAIL "Akatsa direktorio nagusian"
|
||||
#define MSG_SD_CARD_OK "SD card ok"
|
||||
#define MSG_SD_WORKDIR_FAIL "Akatsa lan direktorioan"
|
||||
#define MSG_SD_OPEN_FILE_FAIL "Akatsa irekitzean, File: "
|
||||
#define MSG_SD_FILE_OPENED "Artxiboa irekita: "
|
||||
#define MSG_SD_SIZE " Tamaina: "
|
||||
#define MSG_SD_FILE_SELECTED "Artxiboa aukeratuta"
|
||||
#define MSG_SD_WRITE_TO_FILE "Artxiboa idazten: "
|
||||
#define MSG_SD_PRINTING_BYTE "SD byte idazten "
|
||||
#define MSG_SD_NOT_PRINTING "Ez dago SD-tik inprimatzen"
|
||||
#define MSG_SD_ERR_WRITE_TO_FILE "Akatsak artxiboa idazten"
|
||||
#define MSG_SD_CANT_ENTER_SUBDIR "Azpidirektorio ezin da ireki: "
|
||||
|
||||
#define MSG_STEPPER_TOO_HIGH "Motorra oso goi dago: "
|
||||
#define MSG_ENDSTOPS_HIT "Bide amaiera ukitu da: "
|
||||
#define MSG_ERR_COLD_EXTRUDE_STOP " estrusio hotza saihestua"
|
||||
#define MSG_ERR_LONG_EXTRUDE_STOP " estrusio oso luzea saihestua"
|
||||
#define MSG_BABYSTEPPING_X "Babystepping X"
|
||||
#define MSG_BABYSTEPPING_Y "Babystepping Y"
|
||||
#define MSG_BABYSTEPPING_Z "Babystepping Z"
|
||||
#define MSG_SERIAL_ERROR_MENU_STRUCTURE "Akatsak menu-an"
|
||||
|
||||
#endif
|
||||
|
||||
#endif // ifndef LANGUAGE_H
|
||||
|
|
104
Marlin/pins.h
104
Marlin/pins.h
|
@ -1,6 +1,7 @@
|
|||
#ifndef PINS_H
|
||||
#define PINS_H
|
||||
|
||||
#if MOTHERBOARD != 88
|
||||
#define X_MS1_PIN -1
|
||||
#define X_MS2_PIN -1
|
||||
#define Y_MS1_PIN -1
|
||||
|
@ -12,6 +13,91 @@
|
|||
#define E1_MS1_PIN -1
|
||||
#define E1_MS2_PIN -1
|
||||
#define DIGIPOTSS_PIN -1
|
||||
#endif
|
||||
|
||||
/****************************************************************************************
|
||||
* 5DPrint D8 Driver board
|
||||
* https://bitbucket.org/makible/5dprint-d8-controller-board
|
||||
****************************************************************************************/
|
||||
|
||||
#if MOTHERBOARD == 88
|
||||
|
||||
#define KNOWN_BOARD 1
|
||||
#define AT90USB 1286 // Disable MarlinSerial etc.
|
||||
|
||||
#ifndef __AVR_AT90USB1286__
|
||||
#error Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
|
||||
#endif
|
||||
|
||||
#define LARGE_FLASH true
|
||||
|
||||
#define X_STEP_PIN 0
|
||||
#define X_DIR_PIN 1
|
||||
#define X_ENABLE_PIN 23
|
||||
#define X_STOP_PIN 37
|
||||
|
||||
#define Y_STEP_PIN 2
|
||||
#define Y_DIR_PIN 3
|
||||
#define Y_ENABLE_PIN 19
|
||||
#define Y_STOP_PIN 36
|
||||
|
||||
#define Z_STEP_PIN 4
|
||||
#define Z_DIR_PIN 5
|
||||
#define Z_ENABLE_PIN 18
|
||||
#define Z_STOP_PIN 39
|
||||
|
||||
#define E0_STEP_PIN 6
|
||||
#define E0_DIR_PIN 7
|
||||
#define E0_ENABLE_PIN 17
|
||||
|
||||
#define HEATER_0_PIN 21 // Extruder
|
||||
#define HEATER_1_PIN -1
|
||||
#define HEATER_2_PIN -1
|
||||
#define HEATER_BED_PIN 20 // Bed
|
||||
// You may need to change FAN_PIN to 16 because Marlin isn't using fastio.h
|
||||
// for the fan and Teensyduino uses a different pin mapping.
|
||||
#define FAN_PIN 16 // Fan
|
||||
|
||||
#define TEMP_0_PIN 1 // Extruder / Analog pin numbering
|
||||
#define TEMP_BED_PIN 0 // Bed / Analog pin numbering
|
||||
|
||||
#define TEMP_1_PIN -1
|
||||
#define TEMP_2_PIN -1
|
||||
|
||||
#define SDPOWER -1
|
||||
#define LED_PIN -1
|
||||
#define PS_ON_PIN -1
|
||||
#define KILL_PIN -1
|
||||
#define ALARM_PIN -1
|
||||
|
||||
// The SDSS pin uses a different pin mapping from file Sd2PinMap.h
|
||||
#define SDSS 20
|
||||
|
||||
#ifndef SDSUPPORT
|
||||
// these pins are defined in the SD library if building with SD support
|
||||
#define SCK_PIN 9
|
||||
#define MISO_PIN 11
|
||||
#define MOSI_PIN 10
|
||||
#endif
|
||||
|
||||
// Microstepping pins
|
||||
// Note that the pin mapping is not from fastio.h
|
||||
// See Sd2PinMap.h for the pin configurations
|
||||
#define X_MS1_PIN 25
|
||||
#define X_MS2_PIN 26
|
||||
#define Y_MS1_PIN 9
|
||||
#define Y_MS2_PIN 8
|
||||
#define Z_MS1_PIN 7
|
||||
#define Z_MS2_PIN 6
|
||||
#define E0_MS1_PIN 5
|
||||
#define E0_MS2_PIN 4
|
||||
|
||||
#endif /* 88 */
|
||||
|
||||
/****************************************************************************************
|
||||
*
|
||||
*
|
||||
****************************************************************************************/
|
||||
|
||||
#if MOTHERBOARD == 99
|
||||
#define KNOWN_BOARD 1
|
||||
|
@ -502,7 +588,7 @@
|
|||
#endif
|
||||
|
||||
#if MOTHERBOARD == 35
|
||||
#define CONTROLLERFAN_PIN 10 //Pin used for the fan to cool controller
|
||||
#define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller
|
||||
#endif
|
||||
|
||||
#define PS_ON_PIN 12
|
||||
|
@ -1054,6 +1140,22 @@
|
|||
#define FAN_PIN 4
|
||||
#endif
|
||||
|
||||
#ifdef NUM_SERVOS
|
||||
#define SERVO0_PIN -1
|
||||
|
||||
#if NUM_SERVOS > 1
|
||||
#define SERVO1_PIN -1
|
||||
#endif
|
||||
|
||||
#if NUM_SERVOS > 2
|
||||
#define SERVO2_PIN -1
|
||||
#endif
|
||||
|
||||
#if NUM_SERVOS > 3
|
||||
#define SERVO3_PIN -1
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#define PS_ON_PIN -1
|
||||
#define KILL_PIN -1
|
||||
|
||||
|
|
|
@ -1228,13 +1228,22 @@ void digipot_current(uint8_t driver, int current)
|
|||
|
||||
void microstep_init()
|
||||
{
|
||||
#if defined(X_MS1_PIN) && X_MS1_PIN > -1
|
||||
const uint8_t microstep_modes[] = MICROSTEP_MODES;
|
||||
pinMode(X_MS2_PIN,OUTPUT);
|
||||
pinMode(Y_MS2_PIN,OUTPUT);
|
||||
pinMode(Z_MS2_PIN,OUTPUT);
|
||||
pinMode(E0_MS2_PIN,OUTPUT);
|
||||
|
||||
#if defined(E1_MS1_PIN) && E1_MS1_PIN > -1
|
||||
pinMode(E1_MS1_PIN,OUTPUT);
|
||||
pinMode(E1_MS2_PIN,OUTPUT);
|
||||
#endif
|
||||
|
||||
#if defined(X_MS1_PIN) && X_MS1_PIN > -1
|
||||
pinMode(X_MS1_PIN,OUTPUT);
|
||||
pinMode(X_MS2_PIN,OUTPUT);
|
||||
pinMode(Y_MS1_PIN,OUTPUT);
|
||||
pinMode(Y_MS2_PIN,OUTPUT);
|
||||
pinMode(Z_MS1_PIN,OUTPUT);
|
||||
pinMode(Z_MS2_PIN,OUTPUT);
|
||||
pinMode(E0_MS1_PIN,OUTPUT);
|
||||
pinMode(E0_MS2_PIN,OUTPUT);
|
||||
for(int i=0;i<=4;i++) microstep_mode(i,microstep_modes[i]);
|
||||
#endif
|
||||
}
|
||||
|
@ -1247,7 +1256,9 @@ void microstep_ms(uint8_t driver, int8_t ms1, int8_t ms2)
|
|||
case 1: digitalWrite( Y_MS1_PIN,ms1); break;
|
||||
case 2: digitalWrite( Z_MS1_PIN,ms1); break;
|
||||
case 3: digitalWrite(E0_MS1_PIN,ms1); break;
|
||||
#if defined(E1_MS1_PIN) && E1_MS1_PIN > -1
|
||||
case 4: digitalWrite(E1_MS1_PIN,ms1); break;
|
||||
#endif
|
||||
}
|
||||
if(ms2 > -1) switch(driver)
|
||||
{
|
||||
|
@ -1255,7 +1266,9 @@ void microstep_ms(uint8_t driver, int8_t ms1, int8_t ms2)
|
|||
case 1: digitalWrite( Y_MS2_PIN,ms2); break;
|
||||
case 2: digitalWrite( Z_MS2_PIN,ms2); break;
|
||||
case 3: digitalWrite(E0_MS2_PIN,ms2); break;
|
||||
#if defined(E1_MS2_PIN) && E1_MS2_PIN > -1
|
||||
case 4: digitalWrite(E1_MS2_PIN,ms2); break;
|
||||
#endif
|
||||
}
|
||||
}
|
||||
|
||||
|
@ -1286,8 +1299,10 @@ void microstep_readings()
|
|||
SERIAL_PROTOCOLPGM("E0: ");
|
||||
SERIAL_PROTOCOL( digitalRead(E0_MS1_PIN));
|
||||
SERIAL_PROTOCOLLN( digitalRead(E0_MS2_PIN));
|
||||
#if defined(E1_MS1_PIN) && E1_MS1_PIN > -1
|
||||
SERIAL_PROTOCOLPGM("E1: ");
|
||||
SERIAL_PROTOCOL( digitalRead(E1_MS1_PIN));
|
||||
SERIAL_PROTOCOLLN( digitalRead(E1_MS2_PIN));
|
||||
#endif
|
||||
}
|
||||
|
||||
|
|
|
@ -258,14 +258,14 @@ void PID_autotune(float temp, int extruder, int ncycles)
|
|||
Kp = 0.33*Ku;
|
||||
Ki = Kp/Tu;
|
||||
Kd = Kp*Tu/3;
|
||||
SERIAL_PROTOCOLLNPGM(" Some overshoot ")
|
||||
SERIAL_PROTOCOLLNPGM(" Some overshoot ");
|
||||
SERIAL_PROTOCOLPGM(" Kp: "); SERIAL_PROTOCOLLN(Kp);
|
||||
SERIAL_PROTOCOLPGM(" Ki: "); SERIAL_PROTOCOLLN(Ki);
|
||||
SERIAL_PROTOCOLPGM(" Kd: "); SERIAL_PROTOCOLLN(Kd);
|
||||
Kp = 0.2*Ku;
|
||||
Ki = 2*Kp/Tu;
|
||||
Kd = Kp*Tu/3;
|
||||
SERIAL_PROTOCOLLNPGM(" No overshoot ")
|
||||
SERIAL_PROTOCOLLNPGM(" No overshoot ");
|
||||
SERIAL_PROTOCOLPGM(" Kp: "); SERIAL_PROTOCOLLN(Kp);
|
||||
SERIAL_PROTOCOLPGM(" Ki: "); SERIAL_PROTOCOLLN(Ki);
|
||||
SERIAL_PROTOCOLPGM(" Kd: "); SERIAL_PROTOCOLLN(Kd);
|
||||
|
|
|
@ -564,6 +564,63 @@ const short temptable_10[][2] PROGMEM = {
|
|||
};
|
||||
#endif
|
||||
|
||||
#if (THERMISTORHEATER_0 == 11) || (THERMISTORHEATER_1 == 11) || (THERMISTORHEATER_2 == 11) || (THERMISTORBED == 11)
|
||||
// QU-BD silicone bed QWG-104F-3950 thermistor
|
||||
|
||||
const short temptable_11[][2] PROGMEM = {
|
||||
{1*OVERSAMPLENR, 938},
|
||||
{31*OVERSAMPLENR, 314},
|
||||
{41*OVERSAMPLENR, 290},
|
||||
{51*OVERSAMPLENR, 272},
|
||||
{61*OVERSAMPLENR, 258},
|
||||
{71*OVERSAMPLENR, 247},
|
||||
{81*OVERSAMPLENR, 237},
|
||||
{91*OVERSAMPLENR, 229},
|
||||
{101*OVERSAMPLENR, 221},
|
||||
{111*OVERSAMPLENR, 215},
|
||||
{121*OVERSAMPLENR, 209},
|
||||
{131*OVERSAMPLENR, 204},
|
||||
{141*OVERSAMPLENR, 199},
|
||||
{151*OVERSAMPLENR, 195},
|
||||
{161*OVERSAMPLENR, 190},
|
||||
{171*OVERSAMPLENR, 187},
|
||||
{181*OVERSAMPLENR, 183},
|
||||
{191*OVERSAMPLENR, 179},
|
||||
{201*OVERSAMPLENR, 176},
|
||||
{221*OVERSAMPLENR, 170},
|
||||
{241*OVERSAMPLENR, 165},
|
||||
{261*OVERSAMPLENR, 160},
|
||||
{281*OVERSAMPLENR, 155},
|
||||
{301*OVERSAMPLENR, 150},
|
||||
{331*OVERSAMPLENR, 144},
|
||||
{361*OVERSAMPLENR, 139},
|
||||
{391*OVERSAMPLENR, 133},
|
||||
{421*OVERSAMPLENR, 128},
|
||||
{451*OVERSAMPLENR, 123},
|
||||
{491*OVERSAMPLENR, 117},
|
||||
{531*OVERSAMPLENR, 111},
|
||||
{571*OVERSAMPLENR, 105},
|
||||
{611*OVERSAMPLENR, 100},
|
||||
{641*OVERSAMPLENR, 95},
|
||||
{681*OVERSAMPLENR, 90},
|
||||
{711*OVERSAMPLENR, 85},
|
||||
{751*OVERSAMPLENR, 79},
|
||||
{791*OVERSAMPLENR, 72},
|
||||
{811*OVERSAMPLENR, 69},
|
||||
{831*OVERSAMPLENR, 65},
|
||||
{871*OVERSAMPLENR, 57},
|
||||
{881*OVERSAMPLENR, 55},
|
||||
{901*OVERSAMPLENR, 51},
|
||||
{921*OVERSAMPLENR, 45},
|
||||
{941*OVERSAMPLENR, 39},
|
||||
{971*OVERSAMPLENR, 28},
|
||||
{981*OVERSAMPLENR, 23},
|
||||
{991*OVERSAMPLENR, 17},
|
||||
{1001*OVERSAMPLENR, 9},
|
||||
{1021*OVERSAMPLENR, -27}
|
||||
};
|
||||
#endif
|
||||
|
||||
#if (THERMISTORHEATER_0 == 20) || (THERMISTORHEATER_1 == 20) || (THERMISTORHEATER_2 == 20) || (THERMISTORBED == 20) // PT100 with INA826 amp on Ultimaker v2.0 electronics
|
||||
/* The PT100 in the Ultimaker v2.0 electronics has a high sample value for a high temperature.
|
||||
This does not match the normal thermistor behaviour so we need to set the following defines */
|
||||
|
@ -781,6 +838,14 @@ const short temptable_55[][2] PROGMEM = {
|
|||
#endif
|
||||
|
||||
#if (THERMISTORHEATER_0 == 60) || (THERMISTORHEATER_1 == 60) || (THERMISTORHEATER_2 == 60) || (THERMISTORBED == 60) // Maker's Tool Works Kapton Bed Thermister
|
||||
// ./createTemperatureLookup.py --r0=100000 --t0=25 --r1=0 --r2=4700 --beta=3950
|
||||
// r0: 100000
|
||||
// t0: 25
|
||||
// r1: 0 (parallel with rTherm)
|
||||
// r2: 4700 (series with rTherm)
|
||||
// beta: 3950
|
||||
// min adc: 1 at 0.0048828125 V
|
||||
// max adc: 1023 at 4.9951171875 V
|
||||
const short temptable_60[][2] PROGMEM = {
|
||||
{51*OVERSAMPLENR, 272},
|
||||
{61*OVERSAMPLENR, 258},
|
||||
|
@ -856,6 +921,41 @@ const short temptable_60[][2] PROGMEM = {
|
|||
{1008*OVERSAMPLENR, 0},
|
||||
};
|
||||
#endif
|
||||
#if (THERMISTORBED == 12)
|
||||
//100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
|
||||
const short temptable_12[][2] PROGMEM = {
|
||||
{35*OVERSAMPLENR, 180}, //top rating 180C
|
||||
{211*OVERSAMPLENR, 140},
|
||||
{233*OVERSAMPLENR, 135},
|
||||
{261*OVERSAMPLENR, 130},
|
||||
{290*OVERSAMPLENR, 125},
|
||||
{328*OVERSAMPLENR, 120},
|
||||
{362*OVERSAMPLENR, 115},
|
||||
{406*OVERSAMPLENR, 110},
|
||||
{446*OVERSAMPLENR, 105},
|
||||
{496*OVERSAMPLENR, 100},
|
||||
{539*OVERSAMPLENR, 95},
|
||||
{585*OVERSAMPLENR, 90},
|
||||
{629*OVERSAMPLENR, 85},
|
||||
{675*OVERSAMPLENR, 80},
|
||||
{718*OVERSAMPLENR, 75},
|
||||
{758*OVERSAMPLENR, 70},
|
||||
{793*OVERSAMPLENR, 65},
|
||||
{822*OVERSAMPLENR, 60},
|
||||
{841*OVERSAMPLENR, 55},
|
||||
{875*OVERSAMPLENR, 50},
|
||||
{899*OVERSAMPLENR, 45},
|
||||
{926*OVERSAMPLENR, 40},
|
||||
{946*OVERSAMPLENR, 35},
|
||||
{962*OVERSAMPLENR, 30},
|
||||
{977*OVERSAMPLENR, 25},
|
||||
{987*OVERSAMPLENR, 20},
|
||||
{995*OVERSAMPLENR, 15},
|
||||
{1001*OVERSAMPLENR, 10},
|
||||
{1010*OVERSAMPLENR, 0},
|
||||
{1023*OVERSAMPLENR, -40},
|
||||
};
|
||||
#endif
|
||||
|
||||
// Pt1000 and Pt100 handling
|
||||
//
|
||||
|
|
|
@ -305,37 +305,6 @@ static void lcd_autostart_sd()
|
|||
}
|
||||
#endif
|
||||
|
||||
void lcd_preheat_pla()
|
||||
{
|
||||
setTargetHotend0(plaPreheatHotendTemp);
|
||||
setTargetHotend1(plaPreheatHotendTemp);
|
||||
setTargetHotend2(plaPreheatHotendTemp);
|
||||
setTargetBed(plaPreheatHPBTemp);
|
||||
fanSpeed = plaPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
|
||||
void lcd_preheat_abs()
|
||||
{
|
||||
setTargetHotend0(absPreheatHotendTemp);
|
||||
setTargetHotend1(absPreheatHotendTemp);
|
||||
setTargetHotend2(absPreheatHotendTemp);
|
||||
setTargetBed(absPreheatHPBTemp);
|
||||
fanSpeed = absPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
|
||||
static void lcd_cooldown()
|
||||
{
|
||||
setTargetHotend0(0);
|
||||
setTargetHotend1(0);
|
||||
setTargetHotend2(0);
|
||||
setTargetBed(0);
|
||||
lcd_return_to_status();
|
||||
}
|
||||
|
||||
#ifdef BABYSTEPPING
|
||||
static void lcd_babystep_x()
|
||||
{
|
||||
|
@ -436,6 +405,154 @@ static void lcd_tune_menu()
|
|||
END_MENU();
|
||||
}
|
||||
|
||||
void lcd_preheat_pla0()
|
||||
{
|
||||
setTargetHotend0(plaPreheatHotendTemp);
|
||||
setTargetBed(plaPreheatHPBTemp);
|
||||
fanSpeed = plaPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
|
||||
void lcd_preheat_abs0()
|
||||
{
|
||||
setTargetHotend0(absPreheatHotendTemp);
|
||||
setTargetBed(absPreheatHPBTemp);
|
||||
fanSpeed = absPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
|
||||
#if TEMP_SENSOR_1 != 0 //2nd extruder preheat
|
||||
void lcd_preheat_pla1()
|
||||
{
|
||||
setTargetHotend1(plaPreheatHotendTemp);
|
||||
setTargetBed(plaPreheatHPBTemp);
|
||||
fanSpeed = plaPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
|
||||
void lcd_preheat_abs1()
|
||||
{
|
||||
setTargetHotend1(absPreheatHotendTemp);
|
||||
setTargetBed(absPreheatHPBTemp);
|
||||
fanSpeed = absPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
#endif //2nd extruder preheat
|
||||
|
||||
#if TEMP_SENSOR_2 != 0 //3 extruder preheat
|
||||
void lcd_preheat_pla2()
|
||||
{
|
||||
setTargetHotend2(plaPreheatHotendTemp);
|
||||
setTargetBed(plaPreheatHPBTemp);
|
||||
fanSpeed = plaPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
|
||||
void lcd_preheat_abs2()
|
||||
{
|
||||
setTargetHotend2(absPreheatHotendTemp);
|
||||
setTargetBed(absPreheatHPBTemp);
|
||||
fanSpeed = absPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
#endif //3 extruder preheat
|
||||
|
||||
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 //more than one extruder present
|
||||
void lcd_preheat_pla012()
|
||||
{
|
||||
setTargetHotend0(plaPreheatHotendTemp);
|
||||
setTargetHotend1(plaPreheatHotendTemp);
|
||||
setTargetHotend2(plaPreheatHotendTemp);
|
||||
setTargetBed(plaPreheatHPBTemp);
|
||||
fanSpeed = plaPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
|
||||
void lcd_preheat_abs012()
|
||||
{
|
||||
setTargetHotend0(absPreheatHotendTemp);
|
||||
setTargetHotend1(absPreheatHotendTemp);
|
||||
setTargetHotend2(absPreheatHotendTemp);
|
||||
setTargetBed(absPreheatHPBTemp);
|
||||
fanSpeed = absPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
#endif //more than one extruder present
|
||||
|
||||
void lcd_preheat_pla_bedonly()
|
||||
{
|
||||
setTargetBed(plaPreheatHPBTemp);
|
||||
fanSpeed = plaPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
|
||||
void lcd_preheat_abs_bedonly()
|
||||
{
|
||||
setTargetBed(absPreheatHPBTemp);
|
||||
fanSpeed = absPreheatFanSpeed;
|
||||
lcd_return_to_status();
|
||||
setWatch(); // heater sanity check timer
|
||||
}
|
||||
|
||||
static void lcd_preheat_pla_menu()
|
||||
{
|
||||
START_MENU();
|
||||
MENU_ITEM(back, MSG_PREPARE, lcd_prepare_menu);
|
||||
MENU_ITEM(function, MSG_PREHEAT_PLA0, lcd_preheat_pla0);
|
||||
#if TEMP_SENSOR_1 != 0 //2 extruder preheat
|
||||
MENU_ITEM(function, MSG_PREHEAT_PLA1, lcd_preheat_pla1);
|
||||
#endif //2 extruder preheat
|
||||
#if TEMP_SENSOR_2 != 0 //3 extruder preheat
|
||||
MENU_ITEM(function, MSG_PREHEAT_PLA2, lcd_preheat_pla2);
|
||||
#endif //3 extruder preheat
|
||||
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 //all extruder preheat
|
||||
MENU_ITEM(function, MSG_PREHEAT_PLA012, lcd_preheat_pla012);
|
||||
#endif //2 extruder preheat
|
||||
#if TEMP_SENSOR_BED != 0
|
||||
MENU_ITEM(function, MSG_PREHEAT_PLA_BEDONLY, lcd_preheat_pla_bedonly);
|
||||
#endif
|
||||
END_MENU();
|
||||
}
|
||||
|
||||
static void lcd_preheat_abs_menu()
|
||||
{
|
||||
START_MENU();
|
||||
MENU_ITEM(back, MSG_PREPARE, lcd_prepare_menu);
|
||||
MENU_ITEM(function, MSG_PREHEAT_ABS0, lcd_preheat_abs0);
|
||||
#if TEMP_SENSOR_1 != 0 //2 extruder preheat
|
||||
MENU_ITEM(function, MSG_PREHEAT_ABS1, lcd_preheat_abs1);
|
||||
#endif //2 extruder preheat
|
||||
#if TEMP_SENSOR_2 != 0 //3 extruder preheat
|
||||
MENU_ITEM(function, MSG_PREHEAT_ABS2, lcd_preheat_abs2);
|
||||
#endif //3 extruder preheat
|
||||
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 //all extruder preheat
|
||||
MENU_ITEM(function, MSG_PREHEAT_ABS012, lcd_preheat_abs012);
|
||||
#endif //2 extruder preheat
|
||||
#if TEMP_SENSOR_BED != 0
|
||||
MENU_ITEM(function, MSG_PREHEAT_ABS_BEDONLY, lcd_preheat_abs_bedonly);
|
||||
#endif
|
||||
END_MENU();
|
||||
}
|
||||
|
||||
void lcd_cooldown()
|
||||
{
|
||||
setTargetHotend0(0);
|
||||
setTargetHotend1(0);
|
||||
setTargetHotend2(0);
|
||||
setTargetBed(0);
|
||||
fanSpeed = 0;
|
||||
lcd_return_to_status();
|
||||
}
|
||||
|
||||
static void lcd_prepare_menu()
|
||||
{
|
||||
START_MENU();
|
||||
|
@ -448,8 +565,15 @@ static void lcd_prepare_menu()
|
|||
MENU_ITEM(gcode, MSG_DISABLE_STEPPERS, PSTR("M84"));
|
||||
MENU_ITEM(gcode, MSG_AUTO_HOME, PSTR("G28"));
|
||||
//MENU_ITEM(gcode, MSG_SET_ORIGIN, PSTR("G92 X0 Y0 Z0"));
|
||||
MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla);
|
||||
MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs);
|
||||
#if TEMP_SENSOR_0 != 0
|
||||
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_BED != 0
|
||||
MENU_ITEM(submenu, MSG_PREHEAT_PLA, lcd_preheat_pla_menu);
|
||||
MENU_ITEM(submenu, MSG_PREHEAT_ABS, lcd_preheat_abs_menu);
|
||||
#else
|
||||
MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla0);
|
||||
MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs0);
|
||||
#endif
|
||||
#endif
|
||||
MENU_ITEM(function, MSG_COOLDOWN, lcd_cooldown);
|
||||
#if PS_ON_PIN > -1
|
||||
if (powersupply)
|
||||
|
|
|
@ -204,15 +204,15 @@ M Codes
|
|||
* M140 - Set bed target temp
|
||||
* M190 - Sxxx Wait for bed current temp to reach target temp. Waits only when heating
|
||||
* Rxxx Wait for bed current temp to reach target temp. Waits when heating and cooling
|
||||
* M200 - Set filament diameter
|
||||
* M200 D<millimeters>- set filament diameter and set E axis units to cubic millimeters (use S0 to set back to millimeters).
|
||||
* M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000)
|
||||
* M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!!
|
||||
* M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec
|
||||
* M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate
|
||||
* M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk
|
||||
* M206 - set additional homeing offset
|
||||
* M207 - set retract length S[positive mm] F[feedrate mm/sec] Z[additional zlift/hop]
|
||||
* M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/sec]
|
||||
* M207 - set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop], stays in mm regardless of M200 setting
|
||||
* M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/min]
|
||||
* M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
|
||||
* M218 - set hotend offset (in mm): T<extruder_number> X<offset_on_X> Y<offset_on_Y>
|
||||
* M220 S<factor in percent>- set speed factor override percentage
|
||||
|
|
Reference in a new issue