diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 7aab802c5..1cc2bdc4e 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/default/Configuration_adv.h b/Marlin/src/config/default/Configuration_adv.h
index 7aab802c5..1cc2bdc4e 100644
--- a/Marlin/src/config/default/Configuration_adv.h
+++ b/Marlin/src/config/default/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index 6468fecdb..6acdde3da 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
index 3c583e99a..2634b8c5d 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
index a956ed557..ad0030299 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
index 7aab802c5..1cc2bdc4e 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index feb4e1afe..6269446a6 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
index faf55b9b5..a9e198fc6 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
index 40661a358..13abc5000 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
index 9cc2bf874..e900d9589 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
index 40661a358..13abc5000 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Cartesio/Configuration_adv.h b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
index d632feba0..5f1461a1b 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration_adv.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
index 45992cce4..6e97c0b83 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
index b8c1b5620..b77f7cbbe 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
index 24aa8b1ae..4b461a812 100644
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
index eb9818aea..efe2a65dc 100644
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
index e7befc767..00f32b35b 100644
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
index eb9818aea..efe2a65dc 100644
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Felix/Configuration_adv.h b/Marlin/src/config/examples/Felix/Configuration_adv.h
index 205f9b2be..55fdd9253 100644
--- a/Marlin/src/config/examples/Felix/Configuration_adv.h
+++ b/Marlin/src/config/examples/Felix/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index 217676fe4..11e3e23e7 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
index 1f4dfd5f9..d2c14372b 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
index bc41b990f..0ee2c9146 100644
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/MakerParts/Configuration_adv.h b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
index 7aebd01bd..c3608c8d5 100644
--- a/Marlin/src/config/examples/MakerParts/Configuration_adv.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
index 7c65ff699..27f5ed9d7 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
index e55d1d891..c9cf0e883 100644
--- a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index 72917b914..d94d77dd0 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
index 484e52cd6..08c606f71 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
@@ -754,6 +754,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/RigidBot/Configuration_adv.h b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
index 52c2fafd2..b9b8052f6 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration_adv.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/SCARA/Configuration_adv.h b/Marlin/src/config/examples/SCARA/Configuration_adv.h
index ed6290d1a..70c7f3550 100644
--- a/Marlin/src/config/examples/SCARA/Configuration_adv.h
+++ b/Marlin/src/config/examples/SCARA/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
index db8101419..1007df1bf 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/TheBorg/Configuration_adv.h b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
index 6d72365f5..fb5d0048a 100644
--- a/Marlin/src/config/examples/TheBorg/Configuration_adv.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
index 932a4d258..037d2cfd7 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
index d387726ec..aef9570d1 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
index da3717be4..890a3fd26 100644
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
@@ -759,6 +759,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
index 04ca9efeb..bd5f2641f 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index a17c69209..e863cfd88 100644
--- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
+++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index 4fc0e364e..bf875efe0 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index bf4ec5dba..6c6f18c66 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index eb471b709..aa14fe390 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/generic/Configuration_adv.h b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
index eb471b709..aa14fe390 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
index eb471b709..aa14fe390 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
index ea5c5da50..373b3d453 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
@@ -753,6 +753,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
index c35d5dfb5..a0a82a177 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -748,6 +748,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index 96f21ce3c..810e5857c 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/makibox/Configuration_adv.h b/Marlin/src/config/examples/makibox/Configuration_adv.h
index 9db0c5559..6d1b38c94 100644
--- a/Marlin/src/config/examples/makibox/Configuration_adv.h
+++ b/Marlin/src/config/examples/makibox/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
index fc8b2af43..60a28b09b 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -746,6 +746,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/config/examples/wt150/Configuration_adv.h b/Marlin/src/config/examples/wt150/Configuration_adv.h
index e7ce5cc26..f84a0691f 100644
--- a/Marlin/src/config/examples/wt150/Configuration_adv.h
+++ b/Marlin/src/config/examples/wt150/Configuration_adv.h
@@ -747,6 +747,30 @@
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
+/**
+ * Repeatedly attempt G29 leveling until it succeeds.
+ * Stop after G29_MAX_RETRIES attempts.
+ */
+//#define G29_RETRY_AND_RECOVER
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define G29_MAX_RETRIES 3
+  #define G29_HALT_ON_FAILURE
+  /**
+   * Specify the GCODE commands that will be executed when leveling succeeds,
+   * between attempts, and after the maximum number of retries have been tried.
+   */
+  #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
+  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
+  /**
+   * Specify an action command to send to the host on a recovery attempt or failure.
+   * Will be sent in the form '//action:ACTION_ON_G29_FAILURE', e.g. '//action:probe_failed'.
+   * The host must be configured to handle the action command.
+   */
+  #define G29_ACTION_ON_RECOVER "probe_rewipe"
+  #define G29_ACTION_ON_FAILURE "probe_failed"
+#endif
+
 // @section extras
 
 //
diff --git a/Marlin/src/gcode/gcode.cpp b/Marlin/src/gcode/gcode.cpp
index 20b93af18..88c9555c5 100644
--- a/Marlin/src/gcode/gcode.cpp
+++ b/Marlin/src/gcode/gcode.cpp
@@ -61,6 +61,11 @@ bool GcodeSuite::axis_relative_modes[] = AXIS_RELATIVE_MODES;
   float GcodeSuite::coordinate_system[MAX_COORDINATE_SYSTEMS][XYZ];
 #endif
 
+#if HAS_LEVELING && ENABLED(G29_RETRY_AND_RECOVER)
+  #include "../feature/bedlevel/bedlevel.h"
+  #include "../module/planner.h"
+#endif
+
 /**
  * Set target_extruder from the T parameter or the active_extruder
  *
@@ -125,6 +130,44 @@ void GcodeSuite::dwell(millis_t time) {
   while (PENDING(millis(), time)) idle();
 }
 
+/**
+ * When G29_RETRY_AND_RECOVER is enabled, call G29() in
+ * a loop with recovery and retry handling.
+ */
+#if HAS_LEVELING && ENABLED(G29_RETRY_AND_RECOVER)
+
+  void GcodeSuite::G29_with_retry() {
+    set_bed_leveling_enabled(false);
+    for (uint8_t i = G29_MAX_RETRIES; i--;) {
+      G29();
+      if (planner.leveling_active) break;
+      #ifdef G29_ACTION_ON_RECOVER
+        SERIAL_ECHOLNPGM("//action:" G29_ACTION_ON_RECOVER);
+      #endif
+      #ifdef G29_RECOVERY_COMMANDS
+        process_subcommands_now_P(PSTR(G29_RECOVER_COMMANDS));
+      #endif
+    }
+    if (planner.leveling_active) {
+      #ifdef G29_SUCCESS_COMMANDS
+        process_subcommands_now_P(PSTR(G29_SUCCESS_COMMANDS));
+      #endif
+    }
+    else {
+      #ifdef G29_FAILURE_COMMANDS
+        process_subcommands_now_P(PSTR(G29_FAILURE_COMMANDS));
+      #endif
+      #ifdef G29_ACTION_ON_FAILURE
+        SERIAL_ECHOLNPGM("//action:" G29_ACTION_ON_FAILURE);
+      #endif
+      #if ENABLED(G29_HALT_ON_FAILURE)
+        kill(PSTR(MSG_ERR_PROBING_FAILED));
+      #endif
+    }
+  }
+
+#endif // HAS_LEVELING && G29_RETRY_AND_RECOVER
+
 //
 // Placeholders for non-migrated codes
 //
@@ -135,7 +178,11 @@ void GcodeSuite::dwell(millis_t time) {
 /**
  * Process the parsed command and dispatch it to its handler
  */
-void GcodeSuite::process_parsed_command() {
+void GcodeSuite::process_parsed_command(
+  #if ENABLED(USE_EXECUTE_COMMANDS_IMMEDIATE)
+    const bool no_ok
+  #endif
+) {
   KEEPALIVE_STATE(IN_HANDLER);
 
   // Handle a known G, M, or T
@@ -190,8 +237,14 @@ void GcodeSuite::process_parsed_command() {
       case 28: G28(false); break;                                 // G28: Home all axes, one at a time
 
       #if HAS_LEVELING
-        case 29: G29(); break;                                    // G29: Bed leveling calibration
-      #endif
+        case 29:                                                  // G29: Bed leveling calibration
+          #if ENABLED(G29_RETRY_AND_RECOVER)
+            G29_with_retry();
+          #else
+            G29();
+          #endif
+          break;
+      #endif // HAS_LEVELING
 
       #if HAS_BED_PROBE
         case 30: G30(); break;                                    // G30: Single Z probe
@@ -612,7 +665,10 @@ void GcodeSuite::process_parsed_command() {
 
   KEEPALIVE_STATE(NOT_BUSY);
 
-  ok_to_send();
+  #if ENABLED(USE_EXECUTE_COMMANDS_IMMEDIATE)
+    if (!no_ok)
+  #endif
+      ok_to_send();
 }
 
 /**
@@ -638,6 +694,37 @@ void GcodeSuite::process_next_command() {
   process_parsed_command();
 }
 
+#if ENABLED(USE_EXECUTE_COMMANDS_IMMEDIATE)
+  /**
+   * Run a series of commands, bypassing the command queue to allow
+   * G-code "macros" to be called from within other G-code handlers.
+   */
+  void GcodeSuite::process_subcommands_now_P(const char *pgcode) {
+    // Save the parser state
+    char saved_cmd[strlen(parser.command_ptr) + 1];
+    strcpy(saved_cmd, parser.command_ptr);
+
+    // Process individual commands in string
+    while (pgm_read_byte_near(pgcode)) {
+      // Break up string at '\n' delimiters
+      const char *delim = strchr_P(pgcode, '\n');
+      size_t len = delim ? delim - pgcode : strlen_P(pgcode);
+      char cmd[len + 1];
+      strncpy_P(cmd, pgcode, len);
+      cmd[len] = '\0';
+      pgcode += len;
+      if (delim) pgcode++;
+
+      // Parse the next command in the string
+      parser.parse(cmd);
+      process_parsed_command(true);
+    }
+
+    // Restore the parser state
+    parser.parse(saved_cmd);
+  }
+#endif
+
 #if ENABLED(HOST_KEEPALIVE_FEATURE)
 
   /**
diff --git a/Marlin/src/gcode/gcode.h b/Marlin/src/gcode/gcode.h
index c8b072a23..c9f557c00 100644
--- a/Marlin/src/gcode/gcode.h
+++ b/Marlin/src/gcode/gcode.h
@@ -285,9 +285,17 @@ public:
 
   static bool get_target_extruder_from_command();
   static void get_destination_from_command();
-  static void process_parsed_command();
+  static void process_parsed_command(
+    #if ENABLED(USE_EXECUTE_COMMANDS_IMMEDIATE)
+      const bool no_ok = false
+    #endif
+  );
   static void process_next_command();
 
+  #if ENABLED(USE_EXECUTE_COMMANDS_IMMEDIATE)
+    static void process_subcommands_now_P(const char *pgcode);
+  #endif
+
   FORCE_INLINE static void home_all_axes() { G28(true); }
 
   /**
@@ -380,6 +388,9 @@ private:
 
   #if HAS_LEVELING
     static void G29();
+    #if ENABLED(G29_RETRY_AND_RECOVER)
+      static void G29_with_retry();
+    #endif
   #endif
 
   #if HAS_BED_PROBE
diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h
index 7d2650726..2714739bd 100644
--- a/Marlin/src/inc/Conditionals_post.h
+++ b/Marlin/src/inc/Conditionals_post.h
@@ -1448,4 +1448,8 @@
 // If platform requires early initialization of watchdog to properly boot
 #define EARLY_WATCHDOG (ENABLED(USE_WATCHDOG) && defined(ARDUINO_ARCH_SAM))
 
+#if ENABLED(G29_RETRY_AND_RECOVER)
+  #define USE_EXECUTE_COMMANDS_IMMEDIATE
+#endif
+
 #endif // CONDITIONALS_POST_H