Cohesion 3D Remix: Onboard SD card, Fysetc LCD (#13991)

This commit is contained in:
Bob Kuhn 2019-05-15 00:59:57 -05:00 committed by Scott Lahteine
parent dcaefc68a5
commit 48bd8899bd

View file

@ -139,11 +139,11 @@
//
#if ENABLED(SPINDLE_LASER_ENABLE)
#undef HEATER_0_PIN
#define SPINDLE_LASER_ENA_PIN P2_07 // FET 1
#undef HEATER_BED_PIN
#define SPINDLE_LASER_PWM_PIN P2_05 // Bed FET
#undef FAN_PIN
#define SPINDLE_DIR_PIN P2_06 // FET 4
#define SPINDLE_LASER_ENA_PIN P2_07 // FET 1
#define SPINDLE_LASER_PWM_PIN P2_05 // Bed FET
#define SPINDLE_DIR_PIN P2_06 // FET 4
#endif
//
@ -153,41 +153,134 @@
// defined to use the REPRAP_DISCOUNT_SMART_CONTROLLER.
//
// A remote SD card is currently not supported because the pins routed to the EXP2
// connector are shared with the onboard SD card, and Marlin does not support reading
// G-code files from the onboard SD card.
// connector are shared with the onboard SD card, and Marlin does not support that
// hardware configuration.
//
#if ENABLED(ULTRA_LCD)
#define BEEPER_PIN P1_31 // EXP1-1
#define SD_DETECT_PIN P0_27 // EXP2-7
#if ENABLED(FYSETC_MINI_12864)
#define BTN_EN1 P3_26 // EXP2-5
#define BTN_EN2 P3_25 // EXP2-3
#define BTN_ENC P1_30 // EXP1-2
#define FORCE_SOFT_SPI // REQUIRED - results in LCD soft SPI mode 3
#define LCD_PINS_RS P0_16 // EXP1-4
#define LCD_SDSS P0_28 // EXP2-4
#define LCD_PINS_ENABLE P0_18 // EXP1-3
#define LCD_PINS_D4 P0_15 // EXP1-5
#define BEEPER_PIN P1_31 // EXP1-1
#define BTN_ENC P1_30 // EXP1-2
#define DOGLCD_CS P0_18 // EXP1-3
#define DOGLCD_A0 P0_16 // EXP1-4
#define LCD_RESET_PIN P0_15 // EXP1-5
#define KILL_PIN P2_11 // EXP2-10
// A custom cable is REQUIRED for EXP2 cable because the SCK & MOSI on the card's EXP2 are dedicated
// to the onboard SD card. All required EXP2 signals come from the Ethernet connector. Pin 1 of this
// connector is the one nearest the motor power connector.
#define DOGLCD_SCK P1_17 // EXP2-2 => Ethernet pin 5 (bottom, 3 from left)
#define BTN_EN2 P1_09 // EXP2-3 => Ethernet pin 9 (bottom, 5 from left)
#define BTN_EN1 P1_04 // EXP2-5 => Ethernet pin 11 (bottom, 6 from left)
#define DOGLCD_MOSI P1_01 // EXP2-6 => Ethernet pin 13 (bottom, 7 from left)
#if ENABLED(SDSUPPORT)
#error "SDSUPPORT is not currently supported by the Cohesion3D boards"
// A custom EXP1 cable is required colored LEDs. Pins 1-5, 9, 10 of the cable go to pins 1-5, 9, 10
// on the board's EXP1 connector. Pins 6, 7, and 8 of the EXP1 cable go to the Ethernet connector.
// Rev 1.2 displays do NOT require the RGB LEDs. 2.0 and 2.1 displays do require RGB.
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN P1_16 // EXP1-6 => Ethernet pin 6 (top row, 3 from left)
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN P1_10 // EXP1-7 => Ethernet pin 10 (top row, 5 from left)
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN P1_00 // EXP1-8 => Ethernet pin 12 (top row, 6 from left)
#endif
#elif ENABLED(FYSETC_MINI_12864_2_1)
#define NEOPIXEL_PIN P1_16 // EXP1-6 => Ethernet pin 6 (top row, 3 from left)
#endif
#elif ENABLED(ULTRA_LCD)
#define BEEPER_PIN P1_31 // EXP1-1
//#define SD_DETECT_PIN P0_27 // EXP2-7
#define BTN_EN1 P3_26 // EXP2-5
#define BTN_EN2 P3_25 // EXP2-3
#define BTN_ENC P1_30 // EXP1-2
#define LCD_PINS_RS P0_16 // EXP1-4
#define LCD_SDSS P0_28 // EXP2-4
#define LCD_PINS_ENABLE P0_18 // EXP1-3
#define LCD_PINS_D4 P0_15 // EXP1-5
#define KILL_PIN P2_11 // EXP2-10
#endif // ULTRA_LCD
//
// SD Support
//
#if NONE(LPC_SD_LCD, LPC_SD_ONBOARD, LPC_SD_CUSTOM_CABLE)
#undef USB_SD_DISABLED
#define USB_SD_ONBOARD
#define LPC_SD_ONBOARD
#endif
#if ENABLED(LPC_SD_LCD)
#define SCK_PIN P0_07 // (52) system defined J3-9 & AUX-3
#define MISO_PIN P0_08 // (50) system defined J3-10 & AUX-3
#define MOSI_PIN P0_09 // (51) system defined J3-10 & AUX-3
#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS) - CS used by Marlin
#define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card
#elif ENABLED(LPC_SD_ONBOARD)
#if ENABLED(USB_SD_ONBOARD)
// When sharing the SD card with a PC the LCD menu options are
// needed to mount/unmount and refresh SD. So disable SD detect.
#define SHARED_SD_CARD
#undef SD_DETECT_PIN // No SD detect pin for the onboard card
#endif
#define SCK_PIN P0_07
#define MISO_PIN P0_08
#define MOSI_PIN P0_09
#define SS_PIN P0_06 // Chip select for SD card used by Marlin
#define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card
#endif
//
// Ethernet pins
//
#define ENET_MDIO P1_17
#define ENET_RX_ER P1_14
#define ENET_RXD1 P1_10
#define ENET_MOC P1_16
#define REF_CLK P1_15
#define ENET_RXD0 P1_09
#define ENET_CRS P1_08
#define ENET_TX_EN P1_04
#define ENET_TXD0 P1_00
#define ENET_TXD1 P1_01
//#define ENET_MDIO P1_17 // Ethernet pin 5 (bottom, 3 from left)
//#define ENET_RX_ER P1_14
//#define ENET_RXD1 P1_10 // Ethernet pin 10 (top row, 5 from left)
//#define ENET_MOC P1_16 // Ethernet pin 6 (top row, 3 from left)
//#define REF_CLK P1_15
//#define ENET_RXD0 P1_09 // Ethernet pin 9 (bottom, 5 from left)
//#define ENET_CRS P1_08 // Ethernet pin 8 (top row, 4 from left) - INPUT ONLY
//#define ENET_TX_EN P1_04 // Ethernet pin 11 (bottom, 6 from left)
//#define ENET_TXD0 P1_00 // Ethernet pin 12 (top row, 6 from left)
//#define ENET_TXD1 P1_01 // Ethernet pin 13 (bottom, 7 from left)
/**
* EXP1 pins
* 1 - P1_31
* 2 - P1_30
* 3 - P0_18
* 4 - P0_16
* 5 - P0_15
* 6 - N/C
* 7 - N/C
* 8 - P0_27 (also on EXP2-7)
* 9 - GND
* 10 - +5V
*
*
* EXP2 pins
* 1 - P0_08
* 2 - P0_07
* 3 - P3_26
* 4 - P0_28
* 5 - P3_25
* 6 - P0_09
* 7 - P0_27 (also on EXP1_8)
* 8 - P2_11
* 9 - GND
* 10 - N/C
*/