diff --git a/Marlin/language.h b/Marlin/language.h index e13fc3176..f554c6ae1 100644 --- a/Marlin/language.h +++ b/Marlin/language.h @@ -159,6 +159,43 @@ #define MSG_ERR_EEPROM_WRITE "Error writing to EEPROM!" +// temperature.cpp strings +#define MSG_PID_AUTOTUNE "PID Autotune" +#define MSG_PID_AUTOTUNE_START MSG_PID_AUTOTUNE " start" +#define MSG_PID_AUTOTUNE_FAILED MSG_PID_AUTOTUNE " failed!" +#define MSG_PID_BAD_EXTRUDER_NUM MSG_PID_AUTOTUNE_FAILED " Bad extruder number" +#define MSG_PID_TEMP_TOO_HIGH MSG_PID_AUTOTUNE_FAILED " Temperature too high" +#define MSG_PID_TIMEOUT MSG_PID_AUTOTUNE_FAILED " timeout" +#define MSG_BIAS " bias: " +#define MSG_D " d: " +#define MSG_MIN " min: " +#define MSG_MAX " max: " +#define MSG_KU " Ku: " +#define MSG_TU " Tu: " +#define MSG_CLASSIC_PID " Classic PID " +#define MSG_KP " Kp: " +#define MSG_KI " Ki: " +#define MSG_KD " Kd: " +#define MSG_OK_B "ok B:" +#define MSG_OK_T "ok T:" +#define MSG_AT " @:" +#define MSG_PID_AUTOTUNE_FINISHED MSG_PID_AUTOTUNE " finished! Put the last Kp, Ki and Kd constants from above into Configuration.h" +#define MSG_PID_DEBUG " PID_DEBUG " +#define MSG_PID_DEBUG_INPUT ": Input " +#define MSG_PID_DEBUG_OUTPUT " Output " +#define MSG_PID_DEBUG_PTERM " pTerm " +#define MSG_PID_DEBUG_ITERM " iTerm " +#define MSG_PID_DEBUG_DTERM " dTerm " +#define MSG_HEATING_FAILED "Heating failed" +#define MSG_EXTRUDER_SWITCHED_OFF "Extruder switched off. Temperature difference between temp sensors is too high !" + +#define MSG_INVALID_EXTRUDER_NUM " - Invalid extruder number !" +#define MSG_THERMAL_RUNAWAY_STOP "Thermal Runaway, system stopped! Heater_ID: " +#define MSG_SWITCHED_OFF_MAX " switched off. MAXTEMP triggered !!" +#define MSG_MINTEMP_EXTRUDER_OFF ": Extruder switched off. MINTEMP triggered !" +#define MSG_MAXTEMP_EXTRUDER_OFF ": Extruder" MSG_SWITCHED_OFF_MAX +#define MSG_MAXTEMP_BED_OFF "Heated bed" MSG_SWITCHED_OFF_MAX + // LCD Menu Messages // Add your own character. Reference: https://github.com/MarlinFirmware/Marlin/pull/1434 photos diff --git a/Marlin/language_en.h b/Marlin/language_en.h index 5d38aa970..1ba950af9 100644 --- a/Marlin/language_en.h +++ b/Marlin/language_en.h @@ -255,7 +255,7 @@ #define MSG_VOLUMETRIC "Filament" #endif #ifndef MSG_VOLUMETRIC_ENABLED -#define MSG_VOLUMETRIC_ENABLED "E in mm" STR_h3 +#define MSG_VOLUMETRIC_ENABLED "E in mm" STR_h3 #endif #ifndef MSG_FILAMENT_SIZE_EXTRUDER_0 #define MSG_FILAMENT_SIZE_EXTRUDER_0 "Fil. Dia. 1" @@ -383,23 +383,41 @@ #ifndef MSG_ENDSTOP_ABORT #define MSG_ENDSTOP_ABORT "Endstop abort" #endif +#ifndef MSG_HEATING_FAILED_LCD +#define MSG_HEATING_FAILED_LCD "Heating failed" +#endif +#ifndef MSG_ERR_REDUNDANT_TEMP +#define MSG_ERR_REDUNDANT_TEMP "Err: REDUNDANT TEMP ERROR" +#endif +#ifndef MSG_THERMAL_RUNAWAY +#define MSG_THERMAL_RUNAWAY "THERMAL RUNAWAY" +#endif +#ifndef MSG_ERR_MAXTEMP +#define MSG_ERR_MAXTEMP "Err: MAXTEMP" +#endif +#ifndef MSG_ERR_MINTEMP +#define MSG_ERR_MINTEMP "Err: MINTEMP" +#endif +#ifndef MSG_ERR_MAXTEMP_BED +#define MSG_ERR_MAXTEMP_BED "Err: MAXTEMP BED" +#endif #ifdef DELTA_CALIBRATION_MENU - #ifndef MSG_DELTA_CALIBRATE - #define MSG_DELTA_CALIBRATE "Delta Calibration" - #endif - #ifndef MSG_DELTA_CALIBRATE_X - #define MSG_DELTA_CALIBRATE_X "Calibrate X" - #endif - #ifndef MSG_DELTA_CALIBRATE_Y - #define MSG_DELTA_CALIBRATE_Y "Calibrate Y" - #endif - #ifndef MSG_DELTA_CALIBRATE_Z - #define MSG_DELTA_CALIBRATE_Z "Calibrate Z" - #endif - #ifndef MSG_DELTA_CALIBRATE_CENTER - #define MSG_DELTA_CALIBRATE_CENTER "Calibrate Center" - #endif + #ifndef MSG_DELTA_CALIBRATE + #define MSG_DELTA_CALIBRATE "Delta Calibration" + #endif + #ifndef MSG_DELTA_CALIBRATE_X + #define MSG_DELTA_CALIBRATE_X "Calibrate X" + #endif + #ifndef MSG_DELTA_CALIBRATE_Y + #define MSG_DELTA_CALIBRATE_Y "Calibrate Y" + #endif + #ifndef MSG_DELTA_CALIBRATE_Z + #define MSG_DELTA_CALIBRATE_Z "Calibrate Z" + #endif + #ifndef MSG_DELTA_CALIBRATE_CENTER + #define MSG_DELTA_CALIBRATE_CENTER "Calibrate Center" + #endif #endif // DELTA_CALIBRATION_MENU #endif // LANGUAGE_EN_H diff --git a/Marlin/pins_RUMBA.h b/Marlin/pins_RUMBA.h index 8828ef32d..ce96d750d 100644 --- a/Marlin/pins_RUMBA.h +++ b/Marlin/pins_RUMBA.h @@ -6,6 +6,10 @@ #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu. #endif +#if EXTRUDERS > 3 + #error RUMBA supports up to 3 extruders. Comment this line to keep going. +#endif + #define X_STEP_PIN 17 #define X_DIR_PIN 16 #define X_ENABLE_PIN 48 diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp index d50c4265b..c2f536bcf 100644 --- a/Marlin/temperature.cpp +++ b/Marlin/temperature.cpp @@ -33,9 +33,43 @@ #include "ultralcd.h" #include "temperature.h" #include "watchdog.h" +#include "language.h" #include "Sd2PinMap.h" +//=========================================================================== +//================================== macros ================================= +//=========================================================================== + +#if EXTRUDERS > 4 + #error Unsupported number of extruders +#elif EXTRUDERS > 3 + #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3, v4 } +#elif EXTRUDERS > 2 + #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3 } +#elif EXTRUDERS > 1 + #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2 } +#else + #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1 } +#endif + +#define HAS_TEMP_0 (defined(TEMP_0_PIN) && TEMP_0_PIN >= 0) +#define HAS_TEMP_1 (defined(TEMP_1_PIN) && TEMP_1_PIN >= 0) +#define HAS_TEMP_2 (defined(TEMP_2_PIN) && TEMP_2_PIN >= 0) +#define HAS_TEMP_3 (defined(TEMP_3_PIN) && TEMP_3_PIN >= 0) +#define HAS_TEMP_BED (defined(TEMP_BED_PIN) && TEMP_BED_PIN >= 0) +#define HAS_FILAMENT_SENSOR (defined(FILAMENT_SENSOR) && defined(FILWIDTH_PIN) && FILWIDTH_PIN >= 0) +#define HAS_HEATER_0 (defined(HEATER_0_PIN) && HEATER_0_PIN >= 0) +#define HAS_HEATER_1 (defined(HEATER_1_PIN) && HEATER_1_PIN >= 0) +#define HAS_HEATER_2 (defined(HEATER_2_PIN) && HEATER_2_PIN >= 0) +#define HAS_HEATER_3 (defined(HEATER_3_PIN) && HEATER_3_PIN >= 0) +#define HAS_HEATER_BED (defined(HEATER_BED_PIN) && HEATER_BED_PIN >= 0) +#define HAS_AUTO_FAN_0 (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN >= 0) +#define HAS_AUTO_FAN_1 (defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN >= 0) +#define HAS_AUTO_FAN_2 (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN >= 0) +#define HAS_AUTO_FAN_3 (defined(EXTRUDER_3_AUTO_FAN_PIN) && EXTRUDER_3_AUTO_FAN_PIN >= 0) +#define HAS_AUTO_FAN HAS_AUTO_FAN_0 || HAS_AUTO_FAN_1 || HAS_AUTO_FAN_2 || HAS_AUTO_FAN_3 +#define HAS_FAN (defined(FAN_PIN) && FAN_PIN >= 0) //=========================================================================== //============================= public variables ============================ @@ -71,7 +105,7 @@ float current_temperature_bed = 0.0; unsigned char soft_pwm_bed; #ifdef BABYSTEPPING - volatile int babystepsTodo[3]={0,0,0}; + volatile int babystepsTodo[3] = { 0 }; #endif #ifdef FILAMENT_SENSOR @@ -116,40 +150,26 @@ static volatile bool temp_meas_ready = false; #ifdef FAN_SOFT_PWM static unsigned char soft_pwm_fan; #endif -#if (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1) +#if HAS_AUTO_FAN static unsigned long extruder_autofan_last_check; #endif -#if EXTRUDERS > 4 - # error Unsupported number of extruders -#elif EXTRUDERS > 3 - # define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3, v4 } -#elif EXTRUDERS > 2 - # define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3 } -#elif EXTRUDERS > 1 - # define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2 } -#else - # define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1 } -#endif - #ifdef PIDTEMP -#ifdef PID_PARAMS_PER_EXTRUDER - float Kp[EXTRUDERS] = ARRAY_BY_EXTRUDERS(DEFAULT_Kp, DEFAULT_Kp, DEFAULT_Kp, DEFAULT_Kp); - float Ki[EXTRUDERS] = ARRAY_BY_EXTRUDERS(DEFAULT_Ki*PID_dT, DEFAULT_Ki*PID_dT, DEFAULT_Ki*PID_dT, DEFAULT_Ki*PID_dT); - float Kd[EXTRUDERS] = ARRAY_BY_EXTRUDERS(DEFAULT_Kd / PID_dT, DEFAULT_Kd / PID_dT, DEFAULT_Kd / PID_dT, DEFAULT_Kd / PID_dT); - #ifdef PID_ADD_EXTRUSION_RATE - float Kc[EXTRUDERS] = ARRAY_BY_EXTRUDERS(DEFAULT_Kc, DEFAULT_Kc, DEFAULT_Kc, DEFAULT_Kc); - #endif // PID_ADD_EXTRUSION_RATE -#else //PID_PARAMS_PER_EXTRUDER - float Kp = DEFAULT_Kp; - float Ki = DEFAULT_Ki * PID_dT; - float Kd = DEFAULT_Kd / PID_dT; - #ifdef PID_ADD_EXTRUSION_RATE - float Kc = DEFAULT_Kc; - #endif // PID_ADD_EXTRUSION_RATE -#endif // PID_PARAMS_PER_EXTRUDER + #ifdef PID_PARAMS_PER_EXTRUDER + float Kp[EXTRUDERS] = ARRAY_BY_EXTRUDERS(DEFAULT_Kp, DEFAULT_Kp, DEFAULT_Kp, DEFAULT_Kp); + float Ki[EXTRUDERS] = ARRAY_BY_EXTRUDERS(DEFAULT_Ki*PID_dT, DEFAULT_Ki*PID_dT, DEFAULT_Ki*PID_dT, DEFAULT_Ki*PID_dT); + float Kd[EXTRUDERS] = ARRAY_BY_EXTRUDERS(DEFAULT_Kd / PID_dT, DEFAULT_Kd / PID_dT, DEFAULT_Kd / PID_dT, DEFAULT_Kd / PID_dT); + #ifdef PID_ADD_EXTRUSION_RATE + float Kc[EXTRUDERS] = ARRAY_BY_EXTRUDERS(DEFAULT_Kc, DEFAULT_Kc, DEFAULT_Kc, DEFAULT_Kc); + #endif // PID_ADD_EXTRUSION_RATE + #else //PID_PARAMS_PER_EXTRUDER + float Kp = DEFAULT_Kp; + float Ki = DEFAULT_Ki * PID_dT; + float Kd = DEFAULT_Kd / PID_dT; + #ifdef PID_ADD_EXTRUSION_RATE + float Kc = DEFAULT_Kc; + #endif // PID_ADD_EXTRUSION_RATE + #endif // PID_PARAMS_PER_EXTRUDER #endif //PIDTEMP // Init min and max temp with extreme values to prevent false errors during startup @@ -159,7 +179,7 @@ static int minttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS( 0, 0, 0, 0 ); static int maxttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS( 16383, 16383, 16383, 16383 ); //static int bed_minttemp_raw = HEATER_BED_RAW_LO_TEMP; /* No bed mintemp error implemented?!? */ #ifdef BED_MAXTEMP -static int bed_maxttemp_raw = HEATER_BED_RAW_HI_TEMP; + static int bed_maxttemp_raw = HEATER_BED_RAW_HI_TEMP; #endif #ifdef TEMP_SENSOR_1_AS_REDUNDANT @@ -175,12 +195,12 @@ static float analog2tempBed(int raw); static void updateTemperaturesFromRawValues(); #ifdef WATCH_TEMP_PERIOD -int watch_start_temp[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0,0); -unsigned long watchmillis[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0,0); + int watch_start_temp[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0,0); + unsigned long watchmillis[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0,0); #endif //WATCH_TEMP_PERIOD #ifndef SOFT_PWM_SCALE -#define SOFT_PWM_SCALE 0 + #define SOFT_PWM_SCALE 0 #endif #ifdef FILAMENT_SENSOR @@ -198,113 +218,98 @@ unsigned long watchmillis[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0,0); void PID_autotune(float temp, int extruder, int ncycles) { float input = 0.0; - int cycles=0; + int cycles = 0; bool heating = true; - unsigned long temp_millis = millis(); - unsigned long t1=temp_millis; - unsigned long t2=temp_millis; - long t_high = 0; - long t_low = 0; + unsigned long temp_millis = millis(), t1 = temp_millis, t2 = temp_millis; + long t_high = 0, t_low = 0; long bias, d; float Ku, Tu; float Kp, Ki, Kd; float max = 0, min = 10000; -#if (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_3_AUTO_FAN_PIN) && EXTRUDER_3_AUTO_FAN_PIN > -1) - unsigned long extruder_autofan_last_check = millis(); -#endif - - if ((extruder >= EXTRUDERS) - #if (TEMP_BED_PIN <= -1) - ||(extruder < 0) + #if HAS_AUTO_FAN + unsigned long extruder_autofan_last_check = temp_millis; #endif - ){ - SERIAL_ECHOLN("PID Autotune failed. Bad extruder number."); - return; - } + + if (extruder >= EXTRUDERS + #if !HAS_TEMP_BED + || extruder < 0 + #endif + ) { + SERIAL_ECHOLN(MSG_PID_BAD_EXTRUDER_NUM); + return; + } - SERIAL_ECHOLN("PID Autotune start"); - + SERIAL_ECHOLN(MSG_PID_AUTOTUNE_START); + disable_heater(); // switch off all heaters. - if (extruder<0) - { - soft_pwm_bed = (MAX_BED_POWER)/2; - bias = d = (MAX_BED_POWER)/2; - } - else - { - soft_pwm[extruder] = (PID_MAX)/2; - bias = d = (PID_MAX)/2; - } + if (extruder < 0) + soft_pwm_bed = bias = d = MAX_BED_POWER / 2; + else + soft_pwm[extruder] = bias = d = PID_MAX / 2; + // PID Tuning loop + for(;;) { + unsigned long ms = millis(); - - for(;;) { - - if(temp_meas_ready == true) { // temp sample ready + if (temp_meas_ready == true) { // temp sample ready updateTemperaturesFromRawValues(); input = (extruder<0)?current_temperature_bed:current_temperature[extruder]; - max=max(max,input); - min=min(min,input); + max = max(max, input); + min = min(min, input); - #if (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_3_AUTO_FAN_PIN) && EXTRUDER_3_AUTO_FAN_PIN > -1) - if(millis() - extruder_autofan_last_check > 2500) { - checkExtruderAutoFans(); - extruder_autofan_last_check = millis(); - } + #if HAS_AUTO_FAN + if (ms > extruder_autofan_last_check + 2500) { + checkExtruderAutoFans(); + extruder_autofan_last_check = ms; + } #endif - if(heating == true && input > temp) { - if(millis() - t2 > 5000) { - heating=false; - if (extruder<0) + if (heating == true && input > temp) { + if (ms - t2 > 5000) { + heating = false; + if (extruder < 0) soft_pwm_bed = (bias - d) >> 1; else soft_pwm[extruder] = (bias - d) >> 1; - t1=millis(); - t_high=t1 - t2; - max=temp; + t1 = ms; + t_high = t1 - t2; + max = temp; } } - if(heating == false && input < temp) { - if(millis() - t1 > 5000) { - heating=true; - t2=millis(); - t_low=t2 - t1; - if(cycles > 0) { + if (heating == false && input < temp) { + if (ms - t1 > 5000) { + heating = true; + t2 = ms; + t_low = t2 - t1; + if (cycles > 0) { + long max_pow = extruder < 0 ? MAX_BED_POWER : PID_MAX; bias += (d*(t_high - t_low))/(t_low + t_high); - bias = constrain(bias, 20 ,(extruder<0?(MAX_BED_POWER):(PID_MAX))-20); - if(bias > (extruder<0?(MAX_BED_POWER):(PID_MAX))/2) d = (extruder<0?(MAX_BED_POWER):(PID_MAX)) - 1 - bias; - else d = bias; + bias = constrain(bias, 20, max_pow - 20); + d = (bias > max_pow / 2) ? max_pow - 1 - bias : bias; - SERIAL_PROTOCOLPGM(" bias: "); SERIAL_PROTOCOL(bias); - SERIAL_PROTOCOLPGM(" d: "); SERIAL_PROTOCOL(d); - SERIAL_PROTOCOLPGM(" min: "); SERIAL_PROTOCOL(min); - SERIAL_PROTOCOLPGM(" max: "); SERIAL_PROTOCOLLN(max); - if(cycles > 2) { - Ku = (4.0*d)/(3.14159*(max-min)/2.0); - Tu = ((float)(t_low + t_high)/1000.0); - SERIAL_PROTOCOLPGM(" Ku: "); SERIAL_PROTOCOL(Ku); - SERIAL_PROTOCOLPGM(" Tu: "); SERIAL_PROTOCOLLN(Tu); - Kp = 0.6*Ku; - Ki = 2*Kp/Tu; - Kd = Kp*Tu/8; - SERIAL_PROTOCOLLNPGM(" Classic PID "); - SERIAL_PROTOCOLPGM(" Kp: "); SERIAL_PROTOCOLLN(Kp); - SERIAL_PROTOCOLPGM(" Ki: "); SERIAL_PROTOCOLLN(Ki); - SERIAL_PROTOCOLPGM(" Kd: "); SERIAL_PROTOCOLLN(Kd); + SERIAL_PROTOCOLPGM(MSG_BIAS); SERIAL_PROTOCOL(bias); + SERIAL_PROTOCOLPGM(MSG_D); SERIAL_PROTOCOL(d); + SERIAL_PROTOCOLPGM(MSG_MIN); SERIAL_PROTOCOL(min); + SERIAL_PROTOCOLPGM(MSG_MAX); SERIAL_PROTOCOLLN(max); + if (cycles > 2) { + Ku = (4.0 * d) / (3.14159265 * (max - min) / 2.0); + Tu = ((float)(t_low + t_high) / 1000.0); + SERIAL_PROTOCOLPGM(MSG_KU); SERIAL_PROTOCOL(Ku); + SERIAL_PROTOCOLPGM(MSG_TU); SERIAL_PROTOCOLLN(Tu); + Kp = 0.6 * Ku; + Ki = 2 * Kp / Tu; + Kd = Kp * Tu / 8; + SERIAL_PROTOCOLLNPGM(MSG_CLASSIC_PID); + SERIAL_PROTOCOLPGM(MSG_KP); SERIAL_PROTOCOLLN(Kp); + SERIAL_PROTOCOLPGM(MSG_KI); SERIAL_PROTOCOLLN(Ki); + SERIAL_PROTOCOLPGM(MSG_KD); SERIAL_PROTOCOLLN(Kd); /* Kp = 0.33*Ku; Ki = Kp/Tu; @@ -323,79 +328,80 @@ void PID_autotune(float temp, int extruder, int ncycles) */ } } - if (extruder<0) + if (extruder < 0) soft_pwm_bed = (bias + d) >> 1; else soft_pwm[extruder] = (bias + d) >> 1; cycles++; - min=temp; + min = temp; } } } - if(input > (temp + 20)) { - SERIAL_PROTOCOLLNPGM("PID Autotune failed! Temperature too high"); + if (input > temp + 20) { + SERIAL_PROTOCOLLNPGM(MSG_PID_TEMP_TOO_HIGH); return; } - if(millis() - temp_millis > 2000) { + // Every 2 seconds... + if (ms > temp_millis + 2000) { int p; - if (extruder<0){ - p=soft_pwm_bed; - SERIAL_PROTOCOLPGM("ok B:"); - }else{ - p=soft_pwm[extruder]; - SERIAL_PROTOCOLPGM("ok T:"); + if (extruder < 0) { + p = soft_pwm_bed; + SERIAL_PROTOCOLPGM(MSG_OK_B); + } + else { + p = soft_pwm[extruder]; + SERIAL_PROTOCOLPGM(MSG_OK_T); } - - SERIAL_PROTOCOL(input); - SERIAL_PROTOCOLPGM(" @:"); - SERIAL_PROTOCOLLN(p); - temp_millis = millis(); - } - if(((millis() - t1) + (millis() - t2)) > (10L*60L*1000L*2L)) { - SERIAL_PROTOCOLLNPGM("PID Autotune failed! timeout"); + SERIAL_PROTOCOL(input); + SERIAL_PROTOCOLPGM(MSG_AT); + SERIAL_PROTOCOLLN(p); + + temp_millis = ms; + } // every 2 seconds + // Over 2 minutes? + if (((ms - t1) + (ms - t2)) > (10L*60L*1000L*2L)) { + SERIAL_PROTOCOLLNPGM(MSG_PID_TIMEOUT); return; } - if(cycles > ncycles) { - SERIAL_PROTOCOLLNPGM("PID Autotune finished! Put the last Kp, Ki and Kd constants from above into Configuration.h"); + if (cycles > ncycles) { + SERIAL_PROTOCOLLNPGM(MSG_PID_AUTOTUNE_FINISHED); return; } lcd_update(); } } -void updatePID() -{ -#ifdef PIDTEMP - for(int e = 0; e < EXTRUDERS; e++) { - temp_iState_max[e] = PID_INTEGRAL_DRIVE_MAX / PID_PARAM(Ki,e); - } -#endif -#ifdef PIDTEMPBED - temp_iState_max_bed = PID_INTEGRAL_DRIVE_MAX / bedKi; -#endif +void updatePID() { + #ifdef PIDTEMP + for (int e = 0; e < EXTRUDERS; e++) { + temp_iState_max[e] = PID_INTEGRAL_DRIVE_MAX / PID_PARAM(Ki,e); + } + #endif + #ifdef PIDTEMPBED + temp_iState_max_bed = PID_INTEGRAL_DRIVE_MAX / bedKi; + #endif } - + int getHeaterPower(int heater) { - if (heater<0) - return soft_pwm_bed; - return soft_pwm[heater]; + return heater < 0 ? soft_pwm_bed : soft_pwm[heater]; } -#if (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1) +#if HAS_AUTO_FAN - #if defined(FAN_PIN) && FAN_PIN > -1 - #if EXTRUDER_0_AUTO_FAN_PIN == FAN_PIN + #if HAS_FAN + #if EXTRUDER_0_AUTO_FAN_PIN == FAN_PIN #error "You cannot set EXTRUDER_0_AUTO_FAN_PIN equal to FAN_PIN" #endif - #if EXTRUDER_1_AUTO_FAN_PIN == FAN_PIN + #if EXTRUDER_1_AUTO_FAN_PIN == FAN_PIN #error "You cannot set EXTRUDER_1_AUTO_FAN_PIN equal to FAN_PIN" #endif - #if EXTRUDER_2_AUTO_FAN_PIN == FAN_PIN + #if EXTRUDER_2_AUTO_FAN_PIN == FAN_PIN #error "You cannot set EXTRUDER_2_AUTO_FAN_PIN equal to FAN_PIN" #endif + #if EXTRUDER_3_AUTO_FAN_PIN == FAN_PIN + #error "You cannot set EXTRUDER_3_AUTO_FAN_PIN equal to FAN_PIN" + #endif #endif void setExtruderAutoFanState(int pin, bool state) @@ -412,20 +418,20 @@ void checkExtruderAutoFans() uint8_t fanState = 0; // which fan pins need to be turned on? - #if defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1 + #if HAS_AUTO_FAN_0 if (current_temperature[0] > EXTRUDER_AUTO_FAN_TEMPERATURE) fanState |= 1; #endif - #if defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1 + #if HAS_AUTO_FAN_1 if (current_temperature[1] > EXTRUDER_AUTO_FAN_TEMPERATURE) { - if (EXTRUDER_1_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN) + if (EXTRUDER_1_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN) fanState |= 1; else fanState |= 2; } #endif - #if defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1 + #if HAS_AUTO_FAN_2 if (current_temperature[2] > EXTRUDER_AUTO_FAN_TEMPERATURE) { if (EXTRUDER_2_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN) @@ -436,7 +442,7 @@ void checkExtruderAutoFans() fanState |= 4; } #endif - #if defined(EXTRUDER_3_AUTO_FAN_PIN) && EXTRUDER_3_AUTO_FAN_PIN > -1 + #if HAS_AUTO_FAN_3 if (current_temperature[3] > EXTRUDER_AUTO_FAN_TEMPERATURE) { if (EXTRUDER_3_AUTO_FAN_PIN == EXTRUDER_0_AUTO_FAN_PIN) @@ -451,19 +457,19 @@ void checkExtruderAutoFans() #endif // update extruder auto fan states - #if defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1 + #if HAS_AUTO_FAN_0 setExtruderAutoFanState(EXTRUDER_0_AUTO_FAN_PIN, (fanState & 1) != 0); #endif - #if defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1 + #if HAS_AUTO_FAN_1 if (EXTRUDER_1_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN) setExtruderAutoFanState(EXTRUDER_1_AUTO_FAN_PIN, (fanState & 2) != 0); #endif - #if defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1 + #if HAS_AUTO_FAN_2 if (EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN && EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_1_AUTO_FAN_PIN) setExtruderAutoFanState(EXTRUDER_2_AUTO_FAN_PIN, (fanState & 4) != 0); #endif - #if defined(EXTRUDER_3_AUTO_FAN_PIN) && EXTRUDER_3_AUTO_FAN_PIN > -1 + #if HAS_AUTO_FAN_3 if (EXTRUDER_3_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN && EXTRUDER_3_AUTO_FAN_PIN != EXTRUDER_1_AUTO_FAN_PIN && EXTRUDER_3_AUTO_FAN_PIN != EXTRUDER_2_AUTO_FAN_PIN) @@ -473,47 +479,81 @@ void checkExtruderAutoFans() #endif // any extruder auto fan pins set -void manage_heater() -{ - float pid_input; - float pid_output; +// +// Error checking and Write Routines +// +#if !HAS_HEATER_0 + #error HEATER_0_PIN not defined for this board +#endif +#define WRITE_HEATER_0P(v) WRITE(HEATER_0_PIN, v) +#if EXTRUDERS > 1 || defined(HEATERS_PARALLEL) + #if !HAS_HEATER_1 + #error HEATER_1_PIN not defined for this board + #endif + #define WRITE_HEATER_1(v) WRITE(HEATER_1_PIN, v) + #if EXTRUDERS > 2 + #if !HAS_HEATER_2 + #error HEATER_2_PIN not defined for this board + #endif + #define WRITE_HEATER_2(v) WRITE(HEATER_2_PIN, v) + #if EXTRUDERS > 3 + #if !HAS_HEATER_3 + #error HEATER_3_PIN not defined for this board + #endif + #define WRITE_HEATER_3(v) WRITE(HEATER_3_PIN, v) + #endif + #endif +#endif +#ifdef HEATERS_PARALLEL + #define WRITE_HEATER_0(v) { WRITE_HEATER_0P(v); WRITE_HEATER_1(v); } +#else + #define WRITE_HEATER_0(v) WRITE_HEATER_0P(v) +#endif +#if HAS_HEATER_BED + #define WRITE_HEATER_BED(v) WRITE(HEATER_BED_PIN, v) +#endif +#if HAS_FAN + #define WRITE_FAN(v) WRITE(FAN_PIN, v) +#endif - if(temp_meas_ready != true) //better readability - return; +void manage_heater() { + + if (!temp_meas_ready) return; + + float pid_input, pid_output; updateTemperaturesFromRawValues(); #ifdef HEATER_0_USES_MAX6675 - if (current_temperature[0] > 1023 || current_temperature[0] > HEATER_0_MAXTEMP) { - max_temp_error(0); - } - if (current_temperature[0] == 0 || current_temperature[0] < HEATER_0_MINTEMP) { - min_temp_error(0); - } + float ct = current_temperature[0]; + if (ct > min(HEATER_0_MAXTEMP, 1023)) max_temp_error(0); + if (ct < max(HEATER_0_MINTEMP, 0.01)) min_temp_error(0); #endif //HEATER_0_USES_MAX6675 - for(int e = 0; e < EXTRUDERS; e++) - { + unsigned long ms = millis(); -#if defined (THERMAL_RUNAWAY_PROTECTION_PERIOD) && THERMAL_RUNAWAY_PROTECTION_PERIOD > 0 - thermal_runaway_protection(&thermal_runaway_state_machine[e], &thermal_runaway_timer[e], current_temperature[e], target_temperature[e], e, THERMAL_RUNAWAY_PROTECTION_PERIOD, THERMAL_RUNAWAY_PROTECTION_HYSTERESIS); - #endif + // Loop through all extruders + for (int e = 0; e < EXTRUDERS; e++) { - #ifdef PIDTEMP - pid_input = current_temperature[e]; + #if defined (THERMAL_RUNAWAY_PROTECTION_PERIOD) && THERMAL_RUNAWAY_PROTECTION_PERIOD > 0 + thermal_runaway_protection(&thermal_runaway_state_machine[e], &thermal_runaway_timer[e], current_temperature[e], target_temperature[e], e, THERMAL_RUNAWAY_PROTECTION_PERIOD, THERMAL_RUNAWAY_PROTECTION_HYSTERESIS); + #endif - #ifndef PID_OPENLOOP + #ifdef PIDTEMP + pid_input = current_temperature[e]; + + #ifndef PID_OPENLOOP pid_error[e] = target_temperature[e] - pid_input; - if(pid_error[e] > PID_FUNCTIONAL_RANGE) { + if (pid_error[e] > PID_FUNCTIONAL_RANGE) { pid_output = BANG_MAX; pid_reset[e] = true; } - else if(pid_error[e] < -PID_FUNCTIONAL_RANGE || target_temperature[e] == 0) { + else if (pid_error[e] < -PID_FUNCTIONAL_RANGE || target_temperature[e] == 0) { pid_output = 0; pid_reset[e] = true; } else { - if(pid_reset[e] == true) { + if (pid_reset[e] == true) { temp_iState[e] = 0.0; pid_reset[e] = false; } @@ -524,95 +564,89 @@ void manage_heater() //K1 defined in Configuration.h in the PID settings #define K2 (1.0-K1) - dTerm[e] = (PID_PARAM(Kd,e) * (pid_input - temp_dState[e]))*K2 + (K1 * dTerm[e]); + dTerm[e] = (PID_PARAM(Kd,e) * (pid_input - temp_dState[e])) * K2 + (K1 * dTerm[e]); pid_output = pTerm[e] + iTerm[e] - dTerm[e]; if (pid_output > PID_MAX) { - if (pid_error[e] > 0 ) temp_iState[e] -= pid_error[e]; // conditional un-integration - pid_output=PID_MAX; - } else if (pid_output < 0){ - if (pid_error[e] < 0 ) temp_iState[e] -= pid_error[e]; // conditional un-integration - pid_output=0; + if (pid_error[e] > 0) temp_iState[e] -= pid_error[e]; // conditional un-integration + pid_output = PID_MAX; + } + else if (pid_output < 0) { + if (pid_error[e] < 0) temp_iState[e] -= pid_error[e]; // conditional un-integration + pid_output = 0; } } temp_dState[e] = pid_input; - #else - pid_output = constrain(target_temperature[e], 0, PID_MAX); - #endif //PID_OPENLOOP - #ifdef PID_DEBUG - SERIAL_ECHO_START; - SERIAL_ECHO(" PID_DEBUG "); - SERIAL_ECHO(e); - SERIAL_ECHO(": Input "); - SERIAL_ECHO(pid_input); - SERIAL_ECHO(" Output "); - SERIAL_ECHO(pid_output); - SERIAL_ECHO(" pTerm "); - SERIAL_ECHO(pTerm[e]); - SERIAL_ECHO(" iTerm "); - SERIAL_ECHO(iTerm[e]); - SERIAL_ECHO(" dTerm "); - SERIAL_ECHOLN(dTerm[e]); - #endif //PID_DEBUG - #else /* PID off */ - pid_output = 0; - if(current_temperature[e] < target_temperature[e]) { - pid_output = PID_MAX; - } - #endif + #else + pid_output = constrain(target_temperature[e], 0, PID_MAX); + #endif //PID_OPENLOOP + + #ifdef PID_DEBUG + SERIAL_ECHO_START; + SERIAL_ECHO(MSG_PID_DEBUG); + SERIAL_ECHO(e); + SERIAL_ECHO(MSG_PID_DEBUG_INPUT); + SERIAL_ECHO(pid_input); + SERIAL_ECHO(MSG_PID_DEBUG_OUTPUT); + SERIAL_ECHO(pid_output); + SERIAL_ECHO(MSG_PID_DEBUG_PTERM); + SERIAL_ECHO(pTerm[e]); + SERIAL_ECHO(MSG_PID_DEBUG_ITERM); + SERIAL_ECHO(iTerm[e]); + SERIAL_ECHO(MSG_PID_DEBUG_DTERM); + SERIAL_ECHOLN(dTerm[e]); + #endif //PID_DEBUG + + #else /* PID off */ + + pid_output = 0; + if (current_temperature[e] < target_temperature[e]) pid_output = PID_MAX; + + #endif // Check if temperature is within the correct range - if((current_temperature[e] > minttemp[e]) && (current_temperature[e] < maxttemp[e])) - { - soft_pwm[e] = (int)pid_output >> 1; - } - else { - soft_pwm[e] = 0; - } + soft_pwm[e] = current_temperature[e] > minttemp[e] && current_temperature[e] < maxttemp[e] ? (int)pid_output >> 1 : 0; #ifdef WATCH_TEMP_PERIOD - if(watchmillis[e] && millis() - watchmillis[e] > WATCH_TEMP_PERIOD) - { - if(degHotend(e) < watch_start_temp[e] + WATCH_TEMP_INCREASE) - { - setTargetHotend(0, e); - LCD_MESSAGEPGM("Heating failed"); - SERIAL_ECHO_START; - SERIAL_ECHOLN("Heating failed"); - }else{ - watchmillis[e] = 0; + if (watchmillis[e] && ms > watchmillis[e] + WATCH_TEMP_PERIOD) { + if (degHotend(e) < watch_start_temp[e] + WATCH_TEMP_INCREASE) { + setTargetHotend(0, e); + LCD_MESSAGEPGM(MSG_HEATING_FAILED_LCD); // translatable + SERIAL_ECHO_START; + SERIAL_ECHOLNPGM(MSG_HEATING_FAILED); } - } - #endif + else { + watchmillis[e] = 0; + } + } + #endif //WATCH_TEMP_PERIOD + #ifdef TEMP_SENSOR_1_AS_REDUNDANT - if(fabs(current_temperature[0] - redundant_temperature) > MAX_REDUNDANT_TEMP_SENSOR_DIFF) { + if (fabs(current_temperature[0] - redundant_temperature) > MAX_REDUNDANT_TEMP_SENSOR_DIFF) { disable_heater(); - if(IsStopped() == false) { + if (IsStopped() == false) { SERIAL_ERROR_START; - SERIAL_ERRORLNPGM("Extruder switched off. Temperature difference between temp sensors is too high !"); - LCD_ALERTMESSAGEPGM("Err: REDUNDANT TEMP ERROR"); + SERIAL_ERRORLNPGM(MSG_EXTRUDER_SWITCHED_OFF); + LCD_ALERTMESSAGEPGM(MSG_ERR_REDUNDANT_TEMP); // translatable } #ifndef BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE Stop(); #endif } - #endif - } // End extruder for loop + #endif //TEMP_SENSOR_1_AS_REDUNDANT - #if (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN > -1) || \ - (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN > -1) - if(millis() - extruder_autofan_last_check > 2500) // only need to check fan state very infrequently - { - checkExtruderAutoFans(); - extruder_autofan_last_check = millis(); - } + } // Extruders Loop + + #if HAS_AUTO_FAN + if (ms > extruder_autofan_last_check + 2500) { // only need to check fan state very infrequently + checkExtruderAutoFans(); + extruder_autofan_last_check = ms; + } #endif #ifndef PIDTEMPBED - if(millis() - previous_millis_bed_heater < BED_CHECK_INTERVAL) - return; - previous_millis_bed_heater = millis(); - #endif + if (ms < previous_millis_bed_heater + BED_CHECK_INTERVAL) return; + previous_millis_bed_heater = ms; + #endif //PIDTEMPBED #if TEMP_SENSOR_BED != 0 @@ -620,102 +654,75 @@ void manage_heater() thermal_runaway_protection(&thermal_runaway_bed_state_machine, &thermal_runaway_bed_timer, current_temperature_bed, target_temperature_bed, 9, THERMAL_RUNAWAY_PROTECTION_BED_PERIOD, THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS); #endif - #ifdef PIDTEMPBED - pid_input = current_temperature_bed; + #ifdef PIDTEMPBED + pid_input = current_temperature_bed; - #ifndef PID_OPENLOOP - pid_error_bed = target_temperature_bed - pid_input; - pTerm_bed = bedKp * pid_error_bed; - temp_iState_bed += pid_error_bed; - temp_iState_bed = constrain(temp_iState_bed, temp_iState_min_bed, temp_iState_max_bed); - iTerm_bed = bedKi * temp_iState_bed; + #ifndef PID_OPENLOOP + pid_error_bed = target_temperature_bed - pid_input; + pTerm_bed = bedKp * pid_error_bed; + temp_iState_bed += pid_error_bed; + temp_iState_bed = constrain(temp_iState_bed, temp_iState_min_bed, temp_iState_max_bed); + iTerm_bed = bedKi * temp_iState_bed; - //K1 defined in Configuration.h in the PID settings - #define K2 (1.0-K1) - dTerm_bed= (bedKd * (pid_input - temp_dState_bed))*K2 + (K1 * dTerm_bed); - temp_dState_bed = pid_input; + //K1 defined in Configuration.h in the PID settings + #define K2 (1.0-K1) + dTerm_bed = (bedKd * (pid_input - temp_dState_bed))*K2 + (K1 * dTerm_bed); + temp_dState_bed = pid_input; - pid_output = pTerm_bed + iTerm_bed - dTerm_bed; - if (pid_output > MAX_BED_POWER) { - if (pid_error_bed > 0 ) temp_iState_bed -= pid_error_bed; // conditional un-integration - pid_output=MAX_BED_POWER; - } else if (pid_output < 0){ - if (pid_error_bed < 0 ) temp_iState_bed -= pid_error_bed; // conditional un-integration - pid_output=0; - } + pid_output = pTerm_bed + iTerm_bed - dTerm_bed; + if (pid_output > MAX_BED_POWER) { + if (pid_error_bed > 0) temp_iState_bed -= pid_error_bed; // conditional un-integration + pid_output = MAX_BED_POWER; + } + else if (pid_output < 0) { + if (pid_error_bed < 0) temp_iState_bed -= pid_error_bed; // conditional un-integration + pid_output = 0; + } - #else - pid_output = constrain(target_temperature_bed, 0, MAX_BED_POWER); - #endif //PID_OPENLOOP + #else + pid_output = constrain(target_temperature_bed, 0, MAX_BED_POWER); + #endif //PID_OPENLOOP - if((current_temperature_bed > BED_MINTEMP) && (current_temperature_bed < BED_MAXTEMP)) - { - soft_pwm_bed = (int)pid_output >> 1; - } - else { - soft_pwm_bed = 0; - } + soft_pwm_bed = current_temperature_bed > BED_MINTEMP && current_temperature_bed < BED_MAXTEMP ? (int)pid_output >> 1 : 0; #elif !defined(BED_LIMIT_SWITCHING) // Check if temperature is within the correct range - if((current_temperature_bed > BED_MINTEMP) && (current_temperature_bed < BED_MAXTEMP)) - { - if(current_temperature_bed >= target_temperature_bed) - { - soft_pwm_bed = 0; - } - else - { - soft_pwm_bed = MAX_BED_POWER>>1; - } + if (current_temperature_bed > BED_MINTEMP && current_temperature_bed < BED_MAXTEMP) { + soft_pwm_bed = current_temperature_bed < target_temperature_bed ? MAX_BED_POWER >> 1 : 0; } - else - { + else { soft_pwm_bed = 0; - WRITE(HEATER_BED_PIN,LOW); + WRITE_HEATER_BED(LOW); } #else //#ifdef BED_LIMIT_SWITCHING // Check if temperature is within the correct band - if((current_temperature_bed > BED_MINTEMP) && (current_temperature_bed < BED_MAXTEMP)) - { - if(current_temperature_bed > target_temperature_bed + BED_HYSTERESIS) - { + if (current_temperature_bed > BED_MINTEMP && current_temperature_bed < BED_MAXTEMP) { + if (current_temperature_bed >= target_temperature_bed + BED_HYSTERESIS) soft_pwm_bed = 0; - } - else if(current_temperature_bed <= target_temperature_bed - BED_HYSTERESIS) - { - soft_pwm_bed = MAX_BED_POWER>>1; - } + else if (current_temperature_bed <= target_temperature_bed - BED_HYSTERESIS) + soft_pwm_bed = MAX_BED_POWER >> 1; } - else - { + else { soft_pwm_bed = 0; - WRITE(HEATER_BED_PIN,LOW); + WRITE_HEATER_BED(LOW); } #endif - #endif + #endif //TEMP_SENSOR_BED != 0 -//code for controlling the extruder rate based on the width sensor -#ifdef FILAMENT_SENSOR - if(filament_sensor) - { - meas_shift_index=delay_index1-meas_delay_cm; - if(meas_shift_index<0) - meas_shift_index = meas_shift_index + (MAX_MEASUREMENT_DELAY+1); //loop around buffer if needed + // Control the extruder rate based on the width sensor + #ifdef FILAMENT_SENSOR + if (filament_sensor) { + meas_shift_index = delay_index1 - meas_delay_cm; + if (meas_shift_index < 0) meas_shift_index += MAX_MEASUREMENT_DELAY + 1; //loop around buffer if needed - //get the delayed info and add 100 to reconstitute to a percent of the nominal filament diameter - //then square it to get an area - - if(meas_shift_index<0) - meas_shift_index=0; - else if (meas_shift_index>MAX_MEASUREMENT_DELAY) - meas_shift_index=MAX_MEASUREMENT_DELAY; - - volumetric_multiplier[FILAMENT_SENSOR_EXTRUDER_NUM] = pow((float)(100+measurement_delay[meas_shift_index])/100.0,2); - if (volumetric_multiplier[FILAMENT_SENSOR_EXTRUDER_NUM] <0.01) - volumetric_multiplier[FILAMENT_SENSOR_EXTRUDER_NUM]=0.01; - } -#endif + // Get the delayed info and add 100 to reconstitute to a percent of + // the nominal filament diameter then square it to get an area + meas_shift_index = constrain(meas_shift_index, 0, MAX_MEASUREMENT_DELAY); + float vm = pow((measurement_delay[meas_shift_index] + 100.0) / 100.0, 2); + if (vm < 0.01) vm = 0.01; + volumetric_multiplier[FILAMENT_SENSOR_EXTRUDER_NUM] = vm; + } + #endif //FILAMENT_SENSOR } #define PGM_RD_W(x) (short)pgm_read_word(&x) @@ -723,14 +730,14 @@ void manage_heater() // For hot end temperature measurement. static float analog2temp(int raw, uint8_t e) { #ifdef TEMP_SENSOR_1_AS_REDUNDANT - if(e > EXTRUDERS) + if (e > EXTRUDERS) #else - if(e >= EXTRUDERS) + if (e >= EXTRUDERS) #endif { SERIAL_ERROR_START; SERIAL_ERROR((int)e); - SERIAL_ERRORLNPGM(" - Invalid extruder number !"); + SERIAL_ERRORLNPGM(MSG_INVALID_EXTRUDER_NUM); kill(); return 0.0; } @@ -799,54 +806,45 @@ static float analog2tempBed(int raw) { /* Called to get the raw values into the the actual temperatures. The raw values are created in interrupt context, and this function is called from normal context as it is too slow to run in interrupts and will block the stepper routine otherwise */ -static void updateTemperaturesFromRawValues() -{ - #ifdef HEATER_0_USES_MAX6675 - current_temperature_raw[0] = read_max6675(); - #endif - for(uint8_t e=0;e -1) //check if a sensor is supported - filament_width_meas = analog2widthFil(); - #endif - //Reset the watchdog after we know we have a temperature measurement. - watchdog_reset(); +static void updateTemperaturesFromRawValues() { + #ifdef HEATER_0_USES_MAX6675 + current_temperature_raw[0] = read_max6675(); + #endif + for(uint8_t e = 0; e < EXTRUDERS; e++) { + current_temperature[e] = analog2temp(current_temperature_raw[e], e); + } + current_temperature_bed = analog2tempBed(current_temperature_bed_raw); + #ifdef TEMP_SENSOR_1_AS_REDUNDANT + redundant_temperature = analog2temp(redundant_temperature_raw, 1); + #endif + #if HAS_FILAMENT_SENSOR + filament_width_meas = analog2widthFil(); + #endif + //Reset the watchdog after we know we have a temperature measurement. + watchdog_reset(); - CRITICAL_SECTION_START; - temp_meas_ready = false; - CRITICAL_SECTION_END; + CRITICAL_SECTION_START; + temp_meas_ready = false; + CRITICAL_SECTION_END; } -// For converting raw Filament Width to milimeters #ifdef FILAMENT_SENSOR -float analog2widthFil() { -return current_raw_filwidth/16383.0*5.0; -//return current_raw_filwidth; -} - -// For converting raw Filament Width to a ratio -int widthFil_to_size_ratio() { - -float temp; - -temp=filament_width_meas; -if(filament_width_measMEASURED_UPPER_LIMIT) - temp= MEASURED_UPPER_LIMIT; + // Convert raw Filament Width to millimeters + float analog2widthFil() { + return current_raw_filwidth / 16383.0 * 5.0; + //return current_raw_filwidth; + } -return(filament_width_nominal/temp*100); + // Convert raw Filament Width to a ratio + int widthFil_to_size_ratio() { + float temp = filament_width_meas; + if (temp < MEASURED_LOWER_LIMIT) temp = filament_width_nominal; //assume sensor cut out + else if (temp > MEASURED_UPPER_LIMIT) temp = MEASURED_UPPER_LIMIT; + return filament_width_nominal / temp * 100; + } - -} #endif @@ -855,50 +853,50 @@ return(filament_width_nominal/temp*100); void tp_init() { -#if MB(RUMBA) && ((TEMP_SENSOR_0==-1)||(TEMP_SENSOR_1==-1)||(TEMP_SENSOR_2==-1)||(TEMP_SENSOR_BED==-1)) - //disable RUMBA JTAG in case the thermocouple extension is plugged on top of JTAG connector - MCUCR=(1< -1) + #if HAS_HEATER_0 SET_OUTPUT(HEATER_0_PIN); #endif - #if defined(HEATER_1_PIN) && (HEATER_1_PIN > -1) + #if HAS_HEATER_1 SET_OUTPUT(HEATER_1_PIN); #endif - #if defined(HEATER_2_PIN) && (HEATER_2_PIN > -1) + #if HAS_HEATER_2 SET_OUTPUT(HEATER_2_PIN); #endif - #if defined(HEATER_3_PIN) && (HEATER_3_PIN > -1) + #if HAS_HEATER_3 SET_OUTPUT(HEATER_3_PIN); #endif - #if defined(HEATER_BED_PIN) && (HEATER_BED_PIN > -1) + #if HAS_HEATER_BED SET_OUTPUT(HEATER_BED_PIN); #endif - #if defined(FAN_PIN) && (FAN_PIN > -1) + #if HAS_FAN SET_OUTPUT(FAN_PIN); #ifdef FAST_PWM_FAN - setPwmFrequency(FAN_PIN, 1); // No prescaling. Pwm frequency = F_CPU/256/8 + setPwmFrequency(FAN_PIN, 1); // No prescaling. Pwm frequency = F_CPU/256/8 #endif #ifdef FAN_SOFT_PWM - soft_pwm_fan = fanSpeedSoftPwm / 2; + soft_pwm_fan = fanSpeedSoftPwm / 2; #endif - #endif + #endif #ifdef HEATER_0_USES_MAX6675 @@ -921,57 +919,35 @@ void tp_init() #endif //HEATER_0_USES_MAX6675 + #ifdef DIDR2 + #define ANALOG_SELECT(pin) do{ if (pin < 8) DIDR0 |= 1 << pin; else DIDR2 |= 1 << (pin - 8); }while(0) + #else + #define ANALOG_SELECT(pin) do{ DIDR0 |= 1 << pin; }while(0) + #endif + // Set analog inputs ADCSRA = 1< -1) - #if TEMP_0_PIN < 8 - DIDR0 |= 1 << TEMP_0_PIN; - #else - DIDR2 |= 1<<(TEMP_0_PIN - 8); - #endif + #if HAS_TEMP_0 + ANALOG_SELECT(TEMP_0_PIN); #endif - #if defined(TEMP_1_PIN) && (TEMP_1_PIN > -1) - #if TEMP_1_PIN < 8 - DIDR0 |= 1< -1) - #if TEMP_2_PIN < 8 - DIDR0 |= 1 << TEMP_2_PIN; - #else - DIDR2 |= 1<<(TEMP_2_PIN - 8); - #endif + #if HAS_TEMP_2 + ANALOG_SELECT(TEMP_2_PIN); #endif - #if defined(TEMP_3_PIN) && (TEMP_3_PIN > -1) - #if TEMP_3_PIN < 8 - DIDR0 |= 1 << TEMP_3_PIN; - #else - DIDR2 |= 1<<(TEMP_3_PIN - 8); - #endif + #if HAS_TEMP_3 + ANALOG_SELECT(TEMP_3_PIN); #endif - #if defined(TEMP_BED_PIN) && (TEMP_BED_PIN > -1) - #if TEMP_BED_PIN < 8 - DIDR0 |= 1< -1) - #if FILWIDTH_PIN < 8 - DIDR0 |= 1< HEATER_0_MAXTEMP) { -#if HEATER_0_RAW_LO_TEMP < HEATER_0_RAW_HI_TEMP - maxttemp_raw[0] -= OVERSAMPLENR; -#else - maxttemp_raw[0] += OVERSAMPLENR; -#endif - } -#endif //MAXTEMP + #define TEMP_MIN_ROUTINE(NR) \ + minttemp[NR] = HEATER_ ## NR ## _MINTEMP; \ + while(analog2temp(minttemp_raw[NR], NR) < HEATER_ ## NR ## _MINTEMP) { \ + if (HEATER_ ## NR ## _RAW_LO_TEMP < HEATER_ ## NR ## _RAW_HI_TEMP) \ + minttemp_raw[NR] += OVERSAMPLENR; \ + else \ + minttemp_raw[NR] -= OVERSAMPLENR; \ + } + #define TEMP_MAX_ROUTINE(NR) \ + maxttemp[NR] = HEATER_ ## NR ## _MAXTEMP; \ + while(analog2temp(maxttemp_raw[NR], NR) > HEATER_ ## NR ## _MAXTEMP) { \ + if (HEATER_ ## NR ## _RAW_LO_TEMP < HEATER_ ## NR ## _RAW_HI_TEMP) \ + maxttemp_raw[NR] -= OVERSAMPLENR; \ + else \ + maxttemp_raw[NR] += OVERSAMPLENR; \ + } -#if (EXTRUDERS > 1) && defined(HEATER_1_MINTEMP) - minttemp[1] = HEATER_1_MINTEMP; - while(analog2temp(minttemp_raw[1], 1) < HEATER_1_MINTEMP) { -#if HEATER_1_RAW_LO_TEMP < HEATER_1_RAW_HI_TEMP - minttemp_raw[1] += OVERSAMPLENR; -#else - minttemp_raw[1] -= OVERSAMPLENR; -#endif - } -#endif // MINTEMP 1 -#if (EXTRUDERS > 1) && defined(HEATER_1_MAXTEMP) - maxttemp[1] = HEATER_1_MAXTEMP; - while(analog2temp(maxttemp_raw[1], 1) > HEATER_1_MAXTEMP) { -#if HEATER_1_RAW_LO_TEMP < HEATER_1_RAW_HI_TEMP - maxttemp_raw[1] -= OVERSAMPLENR; -#else - maxttemp_raw[1] += OVERSAMPLENR; -#endif - } -#endif //MAXTEMP 1 + #ifdef HEATER_0_MINTEMP + TEMP_MIN_ROUTINE(0); + #endif + #ifdef HEATER_0_MAXTEMP + TEMP_MAX_ROUTINE(0); + #endif + #if EXTRUDERS > 1 + #ifdef HEATER_1_MINTEMP + TEMP_MIN_ROUTINE(1); + #endif + #ifdef HEATER_1_MAXTEMP + TEMP_MAX_ROUTINE(1); + #endif + #if EXTRUDERS > 2 + #ifdef HEATER_2_MINTEMP + TEMP_MIN_ROUTINE(2); + #endif + #ifdef HEATER_2_MAXTEMP + TEMP_MAX_ROUTINE(2); + #endif + #if EXTRUDERS > 3 + #ifdef HEATER_3_MINTEMP + TEMP_MIN_ROUTINE(3); + #endif + #ifdef HEATER_3_MAXTEMP + TEMP_MAX_ROUTINE(3); + #endif + #endif // EXTRUDERS > 3 + #endif // EXTRUDERS > 2 + #endif // EXTRUDERS > 1 -#if (EXTRUDERS > 2) && defined(HEATER_2_MINTEMP) - minttemp[2] = HEATER_2_MINTEMP; - while(analog2temp(minttemp_raw[2], 2) < HEATER_2_MINTEMP) { -#if HEATER_2_RAW_LO_TEMP < HEATER_2_RAW_HI_TEMP - minttemp_raw[2] += OVERSAMPLENR; -#else - minttemp_raw[2] -= OVERSAMPLENR; -#endif - } -#endif //MINTEMP 2 -#if (EXTRUDERS > 2) && defined(HEATER_2_MAXTEMP) - maxttemp[2] = HEATER_2_MAXTEMP; - while(analog2temp(maxttemp_raw[2], 2) > HEATER_2_MAXTEMP) { -#if HEATER_2_RAW_LO_TEMP < HEATER_2_RAW_HI_TEMP - maxttemp_raw[2] -= OVERSAMPLENR; -#else - maxttemp_raw[2] += OVERSAMPLENR; -#endif - } -#endif //MAXTEMP 2 - -#if (EXTRUDERS > 3) && defined(HEATER_3_MINTEMP) - minttemp[3] = HEATER_3_MINTEMP; - while(analog2temp(minttemp_raw[3], 3) < HEATER_3_MINTEMP) { -#if HEATER_3_RAW_LO_TEMP < HEATER_3_RAW_HI_TEMP - minttemp_raw[3] += OVERSAMPLENR; -#else - minttemp_raw[3] -= OVERSAMPLENR; -#endif - } -#endif //MINTEMP 3 -#if (EXTRUDERS > 3) && defined(HEATER_3_MAXTEMP) - maxttemp[3] = HEATER_3_MAXTEMP; - while(analog2temp(maxttemp_raw[3], 3) > HEATER_3_MAXTEMP) { -#if HEATER_3_RAW_LO_TEMP < HEATER_3_RAW_HI_TEMP - maxttemp_raw[3] -= OVERSAMPLENR; -#else - maxttemp_raw[3] += OVERSAMPLENR; -#endif - } -#endif // MAXTEMP 3 - - -#ifdef BED_MINTEMP - /* No bed MINTEMP error implemented?!? */ /* - while(analog2tempBed(bed_minttemp_raw) < BED_MINTEMP) { -#if HEATER_BED_RAW_LO_TEMP < HEATER_BED_RAW_HI_TEMP - bed_minttemp_raw += OVERSAMPLENR; -#else - bed_minttemp_raw -= OVERSAMPLENR; -#endif - } - */ -#endif //BED_MINTEMP -#ifdef BED_MAXTEMP - while(analog2tempBed(bed_maxttemp_raw) > BED_MAXTEMP) { -#if HEATER_BED_RAW_LO_TEMP < HEATER_BED_RAW_HI_TEMP - bed_maxttemp_raw -= OVERSAMPLENR; -#else - bed_maxttemp_raw += OVERSAMPLENR; -#endif - } -#endif //BED_MAXTEMP + #ifdef BED_MINTEMP + /* No bed MINTEMP error implemented?!? */ /* + while(analog2tempBed(bed_minttemp_raw) < BED_MINTEMP) { + #if HEATER_BED_RAW_LO_TEMP < HEATER_BED_RAW_HI_TEMP + bed_minttemp_raw += OVERSAMPLENR; + #else + bed_minttemp_raw -= OVERSAMPLENR; + #endif + } + */ + #endif //BED_MINTEMP + #ifdef BED_MAXTEMP + while(analog2tempBed(bed_maxttemp_raw) > BED_MAXTEMP) { + #if HEATER_BED_RAW_LO_TEMP < HEATER_BED_RAW_HI_TEMP + bed_maxttemp_raw -= OVERSAMPLENR; + #else + bed_maxttemp_raw += OVERSAMPLENR; + #endif + } + #endif //BED_MAXTEMP } -void setWatch() -{ -#ifdef WATCH_TEMP_PERIOD - for (int e = 0; e < EXTRUDERS; e++) - { - if(degHotend(e) < degTargetHotend(e) - (WATCH_TEMP_INCREASE * 2)) - { - watch_start_temp[e] = degHotend(e); - watchmillis[e] = millis(); - } - } -#endif +void setWatch() { + #ifdef WATCH_TEMP_PERIOD + unsigned long ms = millis(); + for (int e = 0; e < EXTRUDERS; e++) { + if (degHotend(e) < degTargetHotend(e) - (WATCH_TEMP_INCREASE * 2)) { + watch_start_temp[e] = degHotend(e); + watchmillis[e] = ms; + } + } + #endif } -#if defined (THERMAL_RUNAWAY_PROTECTION_PERIOD) && THERMAL_RUNAWAY_PROTECTION_PERIOD > 0 +#if defined(THERMAL_RUNAWAY_PROTECTION_PERIOD) && THERMAL_RUNAWAY_PROTECTION_PERIOD > 0 void thermal_runaway_protection(int *state, unsigned long *timer, float temperature, float target_temperature, int heater_id, int period_seconds, int hysteresis_degc) { /* @@ -1135,16 +1072,18 @@ void thermal_runaway_protection(int *state, unsigned long *timer, float temperat if (temperature >= target_temperature) *state = 2; break; case 2: // "Temperature Stable" state + { + unsigned long ms = millis(); if (temperature >= (target_temperature - hysteresis_degc)) { - *timer = millis(); + *timer = ms; } - else if ( (millis() - *timer) > ((unsigned long) period_seconds) * 1000) + else if ( (ms - *timer) > ((unsigned long) period_seconds) * 1000) { SERIAL_ERROR_START; - SERIAL_ERRORLNPGM("Thermal Runaway, system stopped! Heater_ID: "); + SERIAL_ERRORLNPGM(MSG_THERMAL_RUNAWAY_STOP); SERIAL_ERRORLN((int)heater_id); - LCD_ALERTMESSAGEPGM("THERMAL RUNAWAY"); + LCD_ALERTMESSAGEPGM(MSG_THERMAL_RUNAWAY); // translatable thermal_runaway = true; while(1) { @@ -1160,56 +1099,47 @@ void thermal_runaway_protection(int *state, unsigned long *timer, float temperat lcd_update(); } } - break; + } break; } } -#endif +#endif //THERMAL_RUNAWAY_PROTECTION_PERIOD -void disable_heater() -{ - for(int i=0;i -1 - target_temperature[0]=0; - soft_pwm[0]=0; - #if defined(HEATER_0_PIN) && HEATER_0_PIN > -1 - WRITE(HEATER_0_PIN,LOW); - #endif - #endif - - #if defined(TEMP_1_PIN) && TEMP_1_PIN > -1 && EXTRUDERS > 1 - target_temperature[1]=0; - soft_pwm[1]=0; - #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1 - WRITE(HEATER_1_PIN,LOW); - #endif - #endif - - #if defined(TEMP_2_PIN) && TEMP_2_PIN > -1 && EXTRUDERS > 2 - target_temperature[2]=0; - soft_pwm[2]=0; - #if defined(HEATER_2_PIN) && HEATER_2_PIN > -1 - WRITE(HEATER_2_PIN,LOW); - #endif + + #if HAS_TEMP_0 + target_temperature[0] = 0; + soft_pwm[0] = 0; + WRITE_HEATER_0P(LOW); // If HEATERS_PARALLEL should apply, change to WRITE_HEATER_0 #endif - #if defined(TEMP_3_PIN) && TEMP_3_PIN > -1 && EXTRUDERS > 3 - target_temperature[3]=0; - soft_pwm[3]=0; - #if defined(HEATER_3_PIN) && HEATER_3_PIN > -1 - WRITE(HEATER_3_PIN,LOW); - #endif - #endif + #if EXTRUDERS > 1 && HAS_TEMP_1 + target_temperature[1] = 0; + soft_pwm[1] = 0; + WRITE_HEATER_1(LOW); + #endif + #if EXTRUDERS > 2 && HAS_TEMP_2 + target_temperature[2] = 0; + soft_pwm[2] = 0; + WRITE_HEATER_2(LOW); + #endif - #if defined(TEMP_BED_PIN) && TEMP_BED_PIN > -1 - target_temperature_bed=0; - soft_pwm_bed=0; - #if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1 - WRITE(HEATER_BED_PIN,LOW); + #if EXTRUDERS > 3 && HAS_TEMP_3 + target_temperature[3] = 0; + soft_pwm[3] = 0; + WRITE_HEATER_3(LOW); + #endif + + #if HAS_TEMP_BED + target_temperature_bed = 0; + soft_pwm_bed = 0; + #if HAS_HEATER_BED + WRITE_HEATER_BED(LOW); #endif - #endif + #endif } void max_temp_error(uint8_t e) { @@ -1217,8 +1147,8 @@ void max_temp_error(uint8_t e) { if(IsStopped() == false) { SERIAL_ERROR_START; SERIAL_ERRORLN((int)e); - SERIAL_ERRORLNPGM(": Extruder switched off. MAXTEMP triggered !"); - LCD_ALERTMESSAGEPGM("Err: MAXTEMP"); + SERIAL_ERRORLNPGM(MSG_MAXTEMP_EXTRUDER_OFF); + LCD_ALERTMESSAGEPGM(MSG_ERR_MAXTEMP); // translatable } #ifndef BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE Stop(); @@ -1230,8 +1160,8 @@ void min_temp_error(uint8_t e) { if(IsStopped() == false) { SERIAL_ERROR_START; SERIAL_ERRORLN((int)e); - SERIAL_ERRORLNPGM(": Extruder switched off. MINTEMP triggered !"); - LCD_ALERTMESSAGEPGM("Err: MINTEMP"); + SERIAL_ERRORLNPGM(MSG_MINTEMP_EXTRUDER_OFF); + LCD_ALERTMESSAGEPGM(MSG_ERR_MINTEMP); // translatable } #ifndef BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE Stop(); @@ -1239,13 +1169,13 @@ void min_temp_error(uint8_t e) { } void bed_max_temp_error(void) { -#if HEATER_BED_PIN > -1 - WRITE(HEATER_BED_PIN, 0); -#endif - if(IsStopped() == false) { + #if HAS_HEATER_BED + WRITE_HEATER_BED(0); + #endif + if (IsStopped() == false) { SERIAL_ERROR_START; - SERIAL_ERRORLNPGM("Temperature heated bed switched off. MAXTEMP triggered !!"); - LCD_ALERTMESSAGEPGM("Err: MAXTEMP BED"); + SERIAL_ERRORLNPGM(MSG_MAXTEMP_BED_OFF); + LCD_ALERTMESSAGEPGM(MSG_ERR_MAXTEMP_BED); // translatable } #ifndef BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE Stop(); @@ -1253,66 +1183,84 @@ void bed_max_temp_error(void) { } #ifdef HEATER_0_USES_MAX6675 -#define MAX6675_HEAT_INTERVAL 250 -long max6675_previous_millis = MAX6675_HEAT_INTERVAL; -int max6675_temp = 2000; + #define MAX6675_HEAT_INTERVAL 250 + long max6675_previous_millis = MAX6675_HEAT_INTERVAL; + int max6675_temp = 2000; -static int read_max6675() -{ - if (millis() - max6675_previous_millis < MAX6675_HEAT_INTERVAL) - return max6675_temp; - - max6675_previous_millis = millis(); - max6675_temp = 0; + static int read_max6675() { + + unsigned long ms = millis(); + if (ms < max6675_previous_millis + MAX6675_HEAT_INTERVAL) + return max6675_temp; - #ifdef PRR - PRR &= ~(1<> 3; - } + #ifdef PRR + PRR &= ~(1<> 3; + } + + return max6675_temp; + } #endif //HEATER_0_USES_MAX6675 +/** + * Stages in the ISR loop + */ +enum TempState { + PrepareTemp_0, + MeasureTemp_0, + PrepareTemp_BED, + MeasureTemp_BED, + PrepareTemp_1, + MeasureTemp_1, + PrepareTemp_2, + MeasureTemp_2, + PrepareTemp_3, + MeasureTemp_3, + Prepare_FILWIDTH, + Measure_FILWIDTH, + StartupDelay // Startup, delay initial temp reading a tiny bit so the hardware can settle +}; +// // Timer 0 is shared with millies -ISR(TIMER0_COMPB_vect) -{ +// +ISR(TIMER0_COMPB_vect) { //these variables are only accesible from the ISR, but static, so they don't lose their value static unsigned char temp_count = 0; static unsigned long raw_temp_0_value = 0; @@ -1320,542 +1268,324 @@ ISR(TIMER0_COMPB_vect) static unsigned long raw_temp_2_value = 0; static unsigned long raw_temp_3_value = 0; static unsigned long raw_temp_bed_value = 0; - static unsigned char temp_state = 12; + static TempState temp_state = StartupDelay; static unsigned char pwm_count = (1 << SOFT_PWM_SCALE); - static unsigned char soft_pwm_0; -#ifdef SLOW_PWM_HEATERS - static unsigned char slow_pwm_count = 0; - static unsigned char state_heater_0 = 0; - static unsigned char state_timer_heater_0 = 0; -#endif -#if (EXTRUDERS > 1) || defined(HEATERS_PARALLEL) - static unsigned char soft_pwm_1; -#ifdef SLOW_PWM_HEATERS - static unsigned char state_heater_1 = 0; - static unsigned char state_timer_heater_1 = 0; -#endif -#endif -#if EXTRUDERS > 2 - static unsigned char soft_pwm_2; -#ifdef SLOW_PWM_HEATERS - static unsigned char state_heater_2 = 0; - static unsigned char state_timer_heater_2 = 0; -#endif -#endif -#if EXTRUDERS > 3 - static unsigned char soft_pwm_3; -#ifdef SLOW_PWM_HEATERS - static unsigned char state_heater_3 = 0; - static unsigned char state_timer_heater_3 = 0; -#endif -#endif + // Static members for each heater + #ifdef SLOW_PWM_HEATERS + static unsigned char slow_pwm_count = 0; + #define ISR_STATICS(n) \ + static unsigned char soft_pwm_ ## n; \ + static unsigned char state_heater_ ## n = 0; \ + static unsigned char state_timer_heater_ ## n = 0 + #else + #define ISR_STATICS(n) static unsigned char soft_pwm_ ## n + #endif -#if HEATER_BED_PIN > -1 - static unsigned char soft_pwm_b; -#ifdef SLOW_PWM_HEATERS - static unsigned char state_heater_b = 0; - static unsigned char state_timer_heater_b = 0; -#endif -#endif - -#if defined(FILWIDTH_PIN) &&(FILWIDTH_PIN > -1) - static unsigned long raw_filwidth_value = 0; //added for filament width sensor -#endif - -#ifndef SLOW_PWM_HEATERS - /* - * standard PWM modulation - */ - if(pwm_count == 0){ - soft_pwm_0 = soft_pwm[0]; - if(soft_pwm_0 > 0) { - WRITE(HEATER_0_PIN,1); -#ifdef HEATERS_PARALLEL - WRITE(HEATER_1_PIN,1); -#endif - } else WRITE(HEATER_0_PIN,0); + // Statics per heater + ISR_STATICS(0); + #if (EXTRUDERS > 1) || defined(HEATERS_PARALLEL) + ISR_STATICS(1); + #if EXTRUDERS > 2 + ISR_STATICS(2); + #if EXTRUDERS > 3 + ISR_STATICS(3); + #endif + #endif + #endif + #if HAS_HEATER_BED + ISR_STATICS(BED); + #endif -#if EXTRUDERS > 1 - soft_pwm_1 = soft_pwm[1]; - if(soft_pwm_1 > 0) WRITE(HEATER_1_PIN,1); else WRITE(HEATER_1_PIN,0); -#endif -#if EXTRUDERS > 2 - soft_pwm_2 = soft_pwm[2]; - if(soft_pwm_2 > 0) WRITE(HEATER_2_PIN,1); else WRITE(HEATER_2_PIN,0); -#endif -#if EXTRUDERS > 3 - soft_pwm_3 = soft_pwm[3]; - if(soft_pwm_3 > 0) WRITE(HEATER_3_PIN,1); else WRITE(HEATER_3_PIN,0); -#endif + #if HAS_FILAMENT_SENSOR + static unsigned long raw_filwidth_value = 0; + #endif + + #ifndef SLOW_PWM_HEATERS + /** + * standard PWM modulation + */ + if (pwm_count == 0) { + soft_pwm_0 = soft_pwm[0]; + if (soft_pwm_0 > 0) { + WRITE_HEATER_0(1); + } + else WRITE_HEATER_0P(0); // If HEATERS_PARALLEL should apply, change to WRITE_HEATER_0 - -#if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1 - soft_pwm_b = soft_pwm_bed; - if(soft_pwm_b > 0) WRITE(HEATER_BED_PIN,1); else WRITE(HEATER_BED_PIN,0); -#endif -#ifdef FAN_SOFT_PWM - soft_pwm_fan = fanSpeedSoftPwm / 2; - if(soft_pwm_fan > 0) WRITE(FAN_PIN,1); else WRITE(FAN_PIN,0); -#endif - } - if(soft_pwm_0 < pwm_count) { - WRITE(HEATER_0_PIN,0); -#ifdef HEATERS_PARALLEL - WRITE(HEATER_1_PIN,0); -#endif - } - -#if EXTRUDERS > 1 - if(soft_pwm_1 < pwm_count) WRITE(HEATER_1_PIN,0); -#endif -#if EXTRUDERS > 2 - if(soft_pwm_2 < pwm_count) WRITE(HEATER_2_PIN,0); -#endif -#if EXTRUDERS > 3 - if(soft_pwm_3 < pwm_count) WRITE(HEATER_3_PIN,0); -#endif - -#if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1 - if(soft_pwm_b < pwm_count) WRITE(HEATER_BED_PIN,0); -#endif -#ifdef FAN_SOFT_PWM - if(soft_pwm_fan < pwm_count) WRITE(FAN_PIN,0); -#endif - - pwm_count += (1 << SOFT_PWM_SCALE); - pwm_count &= 0x7f; - -#else //ifndef SLOW_PWM_HEATERS - /* - * SLOW PWM HEATERS - * - * for heaters drived by relay - */ -#ifndef MIN_STATE_TIME -#define MIN_STATE_TIME 16 // MIN_STATE_TIME * 65.5 = time in milliseconds -#endif - if (slow_pwm_count == 0) { - // EXTRUDER 0 - soft_pwm_0 = soft_pwm[0]; - if (soft_pwm_0 > 0) { - // turn ON heather only if the minimum time is up - if (state_timer_heater_0 == 0) { - // if change state set timer - if (state_heater_0 == 0) { - state_timer_heater_0 = MIN_STATE_TIME; - } - state_heater_0 = 1; - WRITE(HEATER_0_PIN, 1); -#ifdef HEATERS_PARALLEL - WRITE(HEATER_1_PIN, 1); -#endif - } - } else { - // turn OFF heather only if the minimum time is up - if (state_timer_heater_0 == 0) { - // if change state set timer - if (state_heater_0 == 1) { - state_timer_heater_0 = MIN_STATE_TIME; - } - state_heater_0 = 0; - WRITE(HEATER_0_PIN, 0); -#ifdef HEATERS_PARALLEL - WRITE(HEATER_1_PIN, 0); -#endif - } - } - -#if EXTRUDERS > 1 - // EXTRUDER 1 - soft_pwm_1 = soft_pwm[1]; - if (soft_pwm_1 > 0) { - // turn ON heather only if the minimum time is up - if (state_timer_heater_1 == 0) { - // if change state set timer - if (state_heater_1 == 0) { - state_timer_heater_1 = MIN_STATE_TIME; - } - state_heater_1 = 1; - WRITE(HEATER_1_PIN, 1); - } - } else { - // turn OFF heather only if the minimum time is up - if (state_timer_heater_1 == 0) { - // if change state set timer - if (state_heater_1 == 1) { - state_timer_heater_1 = MIN_STATE_TIME; - } - state_heater_1 = 0; - WRITE(HEATER_1_PIN, 0); - } - } -#endif - -#if EXTRUDERS > 2 - // EXTRUDER 2 - soft_pwm_2 = soft_pwm[2]; - if (soft_pwm_2 > 0) { - // turn ON heather only if the minimum time is up - if (state_timer_heater_2 == 0) { - // if change state set timer - if (state_heater_2 == 0) { - state_timer_heater_2 = MIN_STATE_TIME; - } - state_heater_2 = 1; - WRITE(HEATER_2_PIN, 1); - } - } else { - // turn OFF heather only if the minimum time is up - if (state_timer_heater_2 == 0) { - // if change state set timer - if (state_heater_2 == 1) { - state_timer_heater_2 = MIN_STATE_TIME; - } - state_heater_2 = 0; - WRITE(HEATER_2_PIN, 0); - } - } -#endif - -#if EXTRUDERS > 3 - // EXTRUDER 3 - soft_pwm_3 = soft_pwm[3]; - if (soft_pwm_3 > 0) { - // turn ON heather only if the minimum time is up - if (state_timer_heater_3 == 0) { - // if change state set timer - if (state_heater_3 == 0) { - state_timer_heater_3 = MIN_STATE_TIME; - } - state_heater_3 = 1; - WRITE(HEATER_3_PIN, 1); - } - } else { - // turn OFF heather only if the minimum time is up - if (state_timer_heater_3 == 0) { - // if change state set timer - if (state_heater_3 == 1) { - state_timer_heater_3 = MIN_STATE_TIME; - } - state_heater_3 = 0; - WRITE(HEATER_3_PIN, 0); - } - } -#endif - -#if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1 - // BED - soft_pwm_b = soft_pwm_bed; - if (soft_pwm_b > 0) { - // turn ON heather only if the minimum time is up - if (state_timer_heater_b == 0) { - // if change state set timer - if (state_heater_b == 0) { - state_timer_heater_b = MIN_STATE_TIME; - } - state_heater_b = 1; - WRITE(HEATER_BED_PIN, 1); - } - } else { - // turn OFF heather only if the minimum time is up - if (state_timer_heater_b == 0) { - // if change state set timer - if (state_heater_b == 1) { - state_timer_heater_b = MIN_STATE_TIME; - } - state_heater_b = 0; - WRITE(HEATER_BED_PIN, 0); - } - } -#endif - } // if (slow_pwm_count == 0) - - // EXTRUDER 0 - if (soft_pwm_0 < slow_pwm_count) { - // turn OFF heather only if the minimum time is up - if (state_timer_heater_0 == 0) { - // if change state set timer - if (state_heater_0 == 1) { - state_timer_heater_0 = MIN_STATE_TIME; - } - state_heater_0 = 0; - WRITE(HEATER_0_PIN, 0); -#ifdef HEATERS_PARALLEL - WRITE(HEATER_1_PIN, 0); -#endif - } - } - -#if EXTRUDERS > 1 - // EXTRUDER 1 - if (soft_pwm_1 < slow_pwm_count) { - // turn OFF heather only if the minimum time is up - if (state_timer_heater_1 == 0) { - // if change state set timer - if (state_heater_1 == 1) { - state_timer_heater_1 = MIN_STATE_TIME; - } - state_heater_1 = 0; - WRITE(HEATER_1_PIN, 0); - } - } -#endif - -#if EXTRUDERS > 2 - // EXTRUDER 2 - if (soft_pwm_2 < slow_pwm_count) { - // turn OFF heather only if the minimum time is up - if (state_timer_heater_2 == 0) { - // if change state set timer - if (state_heater_2 == 1) { - state_timer_heater_2 = MIN_STATE_TIME; - } - state_heater_2 = 0; - WRITE(HEATER_2_PIN, 0); - } - } -#endif - -#if EXTRUDERS > 3 - // EXTRUDER 3 - if (soft_pwm_3 < slow_pwm_count) { - // turn OFF heather only if the minimum time is up - if (state_timer_heater_3 == 0) { - // if change state set timer - if (state_heater_3 == 1) { - state_timer_heater_3 = MIN_STATE_TIME; - } - state_heater_3 = 0; - WRITE(HEATER_3_PIN, 0); - } - } -#endif - -#if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1 - // BED - if (soft_pwm_b < slow_pwm_count) { - // turn OFF heather only if the minimum time is up - if (state_timer_heater_b == 0) { - // if change state set timer - if (state_heater_b == 1) { - state_timer_heater_b = MIN_STATE_TIME; - } - state_heater_b = 0; - WRITE(HEATER_BED_PIN, 0); - } - } -#endif - -#ifdef FAN_SOFT_PWM - if (pwm_count == 0){ - soft_pwm_fan = fanSpeedSoftPwm / 2; - if (soft_pwm_fan > 0) WRITE(FAN_PIN,1); else WRITE(FAN_PIN,0); - } - if (soft_pwm_fan < pwm_count) WRITE(FAN_PIN,0); -#endif - - pwm_count += (1 << SOFT_PWM_SCALE); - pwm_count &= 0x7f; - - // increment slow_pwm_count only every 64 pwm_count circa 65.5ms - if ((pwm_count % 64) == 0) { - slow_pwm_count++; - slow_pwm_count &= 0x7f; - - // Extruder 0 - if (state_timer_heater_0 > 0) { - state_timer_heater_0--; - } - -#if EXTRUDERS > 1 - // Extruder 1 - if (state_timer_heater_1 > 0) - state_timer_heater_1--; -#endif - -#if EXTRUDERS > 2 - // Extruder 2 - if (state_timer_heater_2 > 0) - state_timer_heater_2--; -#endif - -#if EXTRUDERS > 3 - // Extruder 3 - if (state_timer_heater_3 > 0) - state_timer_heater_3--; -#endif - -#if defined(HEATER_BED_PIN) && HEATER_BED_PIN > -1 - // Bed - if (state_timer_heater_b > 0) - state_timer_heater_b--; -#endif - } //if ((pwm_count % 64) == 0) { - -#endif //ifndef SLOW_PWM_HEATERS - - switch(temp_state) { - case 0: // Prepare TEMP_0 - #if defined(TEMP_0_PIN) && (TEMP_0_PIN > -1) - #if TEMP_0_PIN > 7 - ADCSRB = 1< 1 + soft_pwm_1 = soft_pwm[1]; + WRITE_HEATER_1(soft_pwm_1 > 0 ? 1 : 0); + #if EXTRUDERS > 2 + soft_pwm_2 = soft_pwm[2]; + WRITE_HEATER_2(soft_pwm_2 > 0 ? 1 : 0); + #if EXTRUDERS > 3 + soft_pwm_3 = soft_pwm[3]; + WRITE_HEATER_3(soft_pwm_3 > 0 ? 1 : 0); + #endif #endif - ADMUX = ((1 << REFS0) | (TEMP_0_PIN & 0x07)); - ADCSRA |= 1< 0 ? 1 : 0); + #endif + #ifdef FAN_SOFT_PWM + soft_pwm_fan = fanSpeedSoftPwm / 2; + WRITE_FAN(soft_pwm_fan > 0 ? 1 : 0); + #endif + } + + if (soft_pwm_0 < pwm_count) { WRITE_HEATER_0(0); } + #if EXTRUDERS > 1 + if (soft_pwm_1 < pwm_count) WRITE_HEATER_1(0); + #if EXTRUDERS > 2 + if (soft_pwm_2 < pwm_count) WRITE_HEATER_2(0); + #if EXTRUDERS > 3 + if (soft_pwm_3 < pwm_count) WRITE_HEATER_3(0); + #endif + #endif + #endif + + #if HAS_HEATER_BED + if (soft_pwm_BED < pwm_count) WRITE_HEATER_BED(0); + #endif + + #ifdef FAN_SOFT_PWM + if (soft_pwm_fan < pwm_count) WRITE_FAN(0); + #endif + + pwm_count += (1 << SOFT_PWM_SCALE); + pwm_count &= 0x7f; + + #else // SLOW_PWM_HEATERS + /* + * SLOW PWM HEATERS + * + * for heaters drived by relay + */ + #ifndef MIN_STATE_TIME + #define MIN_STATE_TIME 16 // MIN_STATE_TIME * 65.5 = time in milliseconds + #endif + + // Macros for Slow PWM timer logic - HEATERS_PARALLEL applies + #define _SLOW_PWM_ROUTINE(NR, src) \ + soft_pwm_ ## NR = src; \ + if (soft_pwm_ ## NR > 0) { \ + if (state_timer_heater_ ## NR == 0) { \ + if (state_heater_ ## NR == 0) state_timer_heater_ ## NR = MIN_STATE_TIME; \ + state_heater_ ## NR = 1; \ + WRITE_HEATER_ ## NR(1); \ + } \ + } \ + else { \ + if (state_timer_heater_ ## NR == 0) { \ + if (state_heater_ ## NR == 1) state_timer_heater_ ## NR = MIN_STATE_TIME; \ + state_heater_ ## NR = 0; \ + WRITE_HEATER_ ## NR(0); \ + } \ + } + #define SLOW_PWM_ROUTINE(n) _SLOW_PWM_ROUTINE(n, soft_pwm[n]) + + #define PWM_OFF_ROUTINE(NR) \ + if (soft_pwm_ ## NR < slow_pwm_count) { \ + if (state_timer_heater_ ## NR == 0) { \ + if (state_heater_ ## NR == 1) state_timer_heater_ ## NR = MIN_STATE_TIME; \ + state_heater_ ## NR = 0; \ + WRITE_HEATER_ ## NR (0); \ + } \ + } + + if (slow_pwm_count == 0) { + + SLOW_PWM_ROUTINE(0); // EXTRUDER 0 + #if EXTRUDERS > 1 + SLOW_PWM_ROUTINE(1); // EXTRUDER 1 + #if EXTRUDERS > 2 + SLOW_PWM_ROUTINE(2); // EXTRUDER 2 + #if EXTRUDERS > 3 + SLOW_PWM_ROUTINE(3); // EXTRUDER 3 + #endif + #endif + #endif + #if HAS_HEATER_BED + _SLOW_PWM_ROUTINE(BED, soft_pwm_bed); // BED + #endif + + } // slow_pwm_count == 0 + + PWM_OFF_ROUTINE(0); // EXTRUDER 0 + #if EXTRUDERS > 1 + PWM_OFF_ROUTINE(1); // EXTRUDER 1 + #if EXTRUDERS > 2 + PWM_OFF_ROUTINE(2); // EXTRUDER 2 + #if EXTRUDERS > 3 + PWM_OFF_ROUTINE(3); // EXTRUDER 3 + #endif + #endif + #endif + #if HAS_HEATER_BED + PWM_OFF_ROUTINE(BED); // BED + #endif + + #ifdef FAN_SOFT_PWM + if (pwm_count == 0) { + soft_pwm_fan = fanSpeedSoftPwm / 2; + WRITE_FAN(soft_pwm_fan > 0 ? 1 : 0); + } + if (soft_pwm_fan < pwm_count) WRITE_FAN(0); + #endif //FAN_SOFT_PWM + + pwm_count += (1 << SOFT_PWM_SCALE); + pwm_count &= 0x7f; + + // increment slow_pwm_count only every 64 pwm_count circa 65.5ms + if ((pwm_count % 64) == 0) { + slow_pwm_count++; + slow_pwm_count &= 0x7f; + + // EXTRUDER 0 + if (state_timer_heater_0 > 0) state_timer_heater_0--; + #if EXTRUDERS > 1 // EXTRUDER 1 + if (state_timer_heater_1 > 0) state_timer_heater_1--; + #if EXTRUDERS > 2 // EXTRUDER 2 + if (state_timer_heater_2 > 0) state_timer_heater_2--; + #if EXTRUDERS > 3 // EXTRUDER 3 + if (state_timer_heater_3 > 0) state_timer_heater_3--; + #endif + #endif + #endif + #if HAS_HEATER_BED + if (state_timer_heater_BED > 0) state_timer_heater_BED--; + #endif + } // (pwm_count % 64) == 0 + + #endif // SLOW_PWM_HEATERS + + #define SET_ADMUX_ADCSRA(pin) ADMUX = (1 << REFS0) | (pin & 0x07); ADCSRA |= 1< 7) ADCSRB = 1 << MUX5; else ADCSRB = 0; SET_ADMUX_ADCSRA(pin) + #else + #define START_ADC(pin) ADCSRB = 0; SET_ADMUX_ADCSRA(pin) + #endif + + switch(temp_state) { + case PrepareTemp_0: + #if HAS_TEMP_0 + START_ADC(TEMP_0_PIN); #endif lcd_buttons_update(); - temp_state = 1; + temp_state = MeasureTemp_0; break; - case 1: // Measure TEMP_0 - #if defined(TEMP_0_PIN) && (TEMP_0_PIN > -1) + case MeasureTemp_0: + #if HAS_TEMP_0 raw_temp_0_value += ADC; #endif - temp_state = 2; + temp_state = PrepareTemp_BED; break; - case 2: // Prepare TEMP_BED - #if defined(TEMP_BED_PIN) && (TEMP_BED_PIN > -1) - #if TEMP_BED_PIN > 7 - ADCSRB = 1< -1) + case MeasureTemp_BED: + #if HAS_TEMP_BED raw_temp_bed_value += ADC; #endif - temp_state = 4; + temp_state = PrepareTemp_1; break; - case 4: // Prepare TEMP_1 - #if defined(TEMP_1_PIN) && (TEMP_1_PIN > -1) - #if TEMP_1_PIN > 7 - ADCSRB = 1< -1) + case MeasureTemp_1: + #if HAS_TEMP_1 raw_temp_1_value += ADC; #endif - temp_state = 6; + temp_state = PrepareTemp_2; break; - case 6: // Prepare TEMP_2 - #if defined(TEMP_2_PIN) && (TEMP_2_PIN > -1) - #if TEMP_2_PIN > 7 - ADCSRB = 1< -1) + case MeasureTemp_2: + #if HAS_TEMP_2 raw_temp_2_value += ADC; #endif - temp_state = 8; + temp_state = PrepareTemp_3; break; - case 8: // Prepare TEMP_3 - #if defined(TEMP_3_PIN) && (TEMP_3_PIN > -1) - #if TEMP_3_PIN > 7 - ADCSRB = 1< -1) + case MeasureTemp_3: + #if HAS_TEMP_3 raw_temp_3_value += ADC; #endif - temp_state = 10; //change so that Filament Width is also measured + temp_state = Prepare_FILWIDTH; break; - case 10: //Prepare FILWIDTH - #if defined(FILWIDTH_PIN) && (FILWIDTH_PIN> -1) - #if FILWIDTH_PIN>7 - ADCSRB = 1< -1) - //raw_filwidth_value += ADC; //remove to use an IIR filter approach - if(ADC>102) //check that ADC is reading a voltage > 0.5 volts, otherwise don't take in the data. - { - raw_filwidth_value= raw_filwidth_value-(raw_filwidth_value>>7); //multipliy raw_filwidth_value by 127/128 - - raw_filwidth_value= raw_filwidth_value + ((unsigned long)ADC<<7); //add new ADC reading + case Prepare_FILWIDTH: + #if HAS_FILAMENT_SENSOR + START_ADC(FILWIDTH_PIN); + #endif + lcd_buttons_update(); + temp_state = Measure_FILWIDTH; + break; + case Measure_FILWIDTH: + #if HAS_FILAMENT_SENSOR + // raw_filwidth_value += ADC; //remove to use an IIR filter approach + if (ADC > 102) { //check that ADC is reading a voltage > 0.5 volts, otherwise don't take in the data. + raw_filwidth_value -= (raw_filwidth_value>>7); //multiply raw_filwidth_value by 127/128 + raw_filwidth_value += ((unsigned long)ADC<<7); //add new ADC reading } - #endif - temp_state = 0; - - temp_count++; - break; - - - case 12: //Startup, delay initial temp reading a tiny bit so the hardware can settle. - temp_state = 0; + #endif + temp_state = PrepareTemp_0; + temp_count++; + break; + case StartupDelay: + temp_state = PrepareTemp_0; break; -// default: -// SERIAL_ERROR_START; -// SERIAL_ERRORLNPGM("Temp measurement error!"); -// break; - } - - if(temp_count >= OVERSAMPLENR) // 10 * 16 * 1/(16000000/64/256) = 164ms. - { - if (!temp_meas_ready) //Only update the raw values if they have been read. Else we could be updating them during reading. - { -#ifndef HEATER_0_USES_MAX6675 - current_temperature_raw[0] = raw_temp_0_value; -#endif -#if EXTRUDERS > 1 - current_temperature_raw[1] = raw_temp_1_value; -#endif -#ifdef TEMP_SENSOR_1_AS_REDUNDANT - redundant_temperature_raw = raw_temp_1_value; -#endif -#if EXTRUDERS > 2 - current_temperature_raw[2] = raw_temp_2_value; -#endif -#if EXTRUDERS > 3 - current_temperature_raw[3] = raw_temp_3_value; -#endif - current_temperature_bed_raw = raw_temp_bed_value; - } -//Add similar code for Filament Sensor - can be read any time since IIR filtering is used -#if defined(FILWIDTH_PIN) &&(FILWIDTH_PIN > -1) - current_raw_filwidth = raw_filwidth_value>>10; //need to divide to get to 0-16384 range since we used 1/128 IIR filter approach -#endif + // default: + // SERIAL_ERROR_START; + // SERIAL_ERRORLNPGM("Temp measurement error!"); + // break; + } // switch(temp_state) + if (temp_count >= OVERSAMPLENR) { // 10 * 16 * 1/(16000000/64/256) = 164ms. + if (!temp_meas_ready) { //Only update the raw values if they have been read. Else we could be updating them during reading. + #ifndef HEATER_0_USES_MAX6675 + current_temperature_raw[0] = raw_temp_0_value; + #endif + #if EXTRUDERS > 1 + current_temperature_raw[1] = raw_temp_1_value; + #if EXTRUDERS > 2 + current_temperature_raw[2] = raw_temp_2_value; + #if EXTRUDERS > 3 + current_temperature_raw[3] = raw_temp_3_value; + #endif + #endif + #endif + #ifdef TEMP_SENSOR_1_AS_REDUNDANT + redundant_temperature_raw = raw_temp_1_value; + #endif + current_temperature_bed_raw = raw_temp_bed_value; + } //!temp_meas_ready + + // Filament Sensor - can be read any time since IIR filtering is used + #if HAS_FILAMENT_SENSOR + current_raw_filwidth = raw_filwidth_value >> 10; // Divide to get to 0-16384 range since we used 1/128 IIR filter approach + #endif temp_meas_ready = true; temp_count = 0; @@ -1865,131 +1595,47 @@ ISR(TIMER0_COMPB_vect) raw_temp_3_value = 0; raw_temp_bed_value = 0; -#if HEATER_0_RAW_LO_TEMP > HEATER_0_RAW_HI_TEMP - if(current_temperature_raw[0] <= maxttemp_raw[0]) { -#else - if(current_temperature_raw[0] >= maxttemp_raw[0]) { -#endif -#ifndef HEATER_0_USES_MAX6675 - max_temp_error(0); -#endif - } -#if HEATER_0_RAW_LO_TEMP > HEATER_0_RAW_HI_TEMP - if(current_temperature_raw[0] >= minttemp_raw[0]) { -#else - if(current_temperature_raw[0] <= minttemp_raw[0]) { -#endif -#ifndef HEATER_0_USES_MAX6675 - min_temp_error(0); -#endif - } + #if HEATER_0_RAW_LO_TEMP > HEATER_0_RAW_HI_TEMP + #define MAXTEST <= + #define MINTEST >= + #else + #define MAXTEST >= + #define MINTEST <= + #endif + for (int i=0; i= OVERSAMPLENR -#if EXTRUDERS > 1 -#if HEATER_1_RAW_LO_TEMP > HEATER_1_RAW_HI_TEMP - if(current_temperature_raw[1] <= maxttemp_raw[1]) { -#else - if(current_temperature_raw[1] >= maxttemp_raw[1]) { -#endif - max_temp_error(1); + #ifdef BABYSTEPPING + for (uint8_t axis=X_AXIS; axis<=Z_AXIS; axis++) { + int curTodo=babystepsTodo[axis]; //get rid of volatile for performance + + if (curTodo > 0) { + babystep(axis,/*fwd*/true); + babystepsTodo[axis]--; //less to do next time + } + else if(curTodo < 0) { + babystep(axis,/*fwd*/false); + babystepsTodo[axis]++; //less to do next time + } } -#if HEATER_1_RAW_LO_TEMP > HEATER_1_RAW_HI_TEMP - if(current_temperature_raw[1] >= minttemp_raw[1]) { -#else - if(current_temperature_raw[1] <= minttemp_raw[1]) { -#endif - min_temp_error(1); - } -#endif -#if EXTRUDERS > 2 -#if HEATER_2_RAW_LO_TEMP > HEATER_2_RAW_HI_TEMP - if(current_temperature_raw[2] <= maxttemp_raw[2]) { -#else - if(current_temperature_raw[2] >= maxttemp_raw[2]) { -#endif - max_temp_error(2); - } -#if HEATER_2_RAW_LO_TEMP > HEATER_2_RAW_HI_TEMP - if(current_temperature_raw[2] >= minttemp_raw[2]) { -#else - if(current_temperature_raw[2] <= minttemp_raw[2]) { -#endif - min_temp_error(2); - } -#endif -#if EXTRUDERS > 3 -#if HEATER_3_RAW_LO_TEMP > HEATER_3_RAW_HI_TEMP - if(current_temperature_raw[3] <= maxttemp_raw[3]) { -#else - if(current_temperature_raw[3] >= maxttemp_raw[3]) { -#endif - max_temp_error(3); - } -#if HEATER_3_RAW_LO_TEMP > HEATER_3_RAW_HI_TEMP - if(current_temperature_raw[3] >= minttemp_raw[3]) { -#else - if(current_temperature_raw[3] <= minttemp_raw[3]) { -#endif - min_temp_error(3); - } -#endif - - - /* No bed MINTEMP error? */ -#if defined(BED_MAXTEMP) && (TEMP_SENSOR_BED != 0) -# if HEATER_BED_RAW_LO_TEMP > HEATER_BED_RAW_HI_TEMP - if(current_temperature_bed_raw <= bed_maxttemp_raw) { -#else - if(current_temperature_bed_raw >= bed_maxttemp_raw) { -#endif - target_temperature_bed = 0; - bed_max_temp_error(); - } -#endif - } - -#ifdef BABYSTEPPING - for(uint8_t axis=0;axis<3;axis++) - { - int curTodo=babystepsTodo[axis]; //get rid of volatile for performance - - if(curTodo>0) - { - babystep(axis,/*fwd*/true); - babystepsTodo[axis]--; //less to do next time - } - else - if(curTodo<0) - { - babystep(axis,/*fwd*/false); - babystepsTodo[axis]++; //less to do next time - } - } -#endif //BABYSTEPPING + #endif //BABYSTEPPING } #ifdef PIDTEMP -// Apply the scale factors to the PID values - - -float scalePID_i(float i) -{ - return i*PID_dT; -} - -float unscalePID_i(float i) -{ - return i/PID_dT; -} - -float scalePID_d(float d) -{ - return d/PID_dT; -} - -float unscalePID_d(float d) -{ - return d*PID_dT; -} - + // Apply the scale factors to the PID values + float scalePID_i(float i) { return i * PID_dT; } + float unscalePID_i(float i) { return i / PID_dT; } + float scalePID_d(float d) { return d / PID_dT; } + float unscalePID_d(float d) { return d * PID_dT; } #endif //PIDTEMP diff --git a/Marlin/temperature.h b/Marlin/temperature.h index b05cb2ef4..b29fc2b57 100644 --- a/Marlin/temperature.h +++ b/Marlin/temperature.h @@ -85,55 +85,25 @@ extern float current_temperature_bed; //inline so that there is no performance decrease. //deg=degreeCelsius -FORCE_INLINE float degHotend(uint8_t extruder) { - return current_temperature[extruder]; -}; +FORCE_INLINE float degHotend(uint8_t extruder) { return current_temperature[extruder]; } +FORCE_INLINE float degBed() { return current_temperature_bed; } #ifdef SHOW_TEMP_ADC_VALUES - FORCE_INLINE float rawHotendTemp(uint8_t extruder) { - return current_temperature_raw[extruder]; - }; - - FORCE_INLINE float rawBedTemp() { - return current_temperature_bed_raw; - }; + FORCE_INLINE float rawHotendTemp(uint8_t extruder) { return current_temperature_raw[extruder]; } + FORCE_INLINE float rawBedTemp() { return current_temperature_bed_raw; } #endif -FORCE_INLINE float degBed() { - return current_temperature_bed; -}; +FORCE_INLINE float degTargetHotend(uint8_t extruder) { return target_temperature[extruder]; } +FORCE_INLINE float degTargetBed() { return target_temperature_bed; } -FORCE_INLINE float degTargetHotend(uint8_t extruder) { - return target_temperature[extruder]; -}; +FORCE_INLINE void setTargetHotend(const float &celsius, uint8_t extruder) { target_temperature[extruder] = celsius; } +FORCE_INLINE void setTargetBed(const float &celsius) { target_temperature_bed = celsius; } -FORCE_INLINE float degTargetBed() { - return target_temperature_bed; -}; +FORCE_INLINE bool isHeatingHotend(uint8_t extruder) { return target_temperature[extruder] > current_temperature[extruder]; } +FORCE_INLINE bool isHeatingBed() { return target_temperature_bed > current_temperature_bed; } -FORCE_INLINE void setTargetHotend(const float &celsius, uint8_t extruder) { - target_temperature[extruder] = celsius; -}; - -FORCE_INLINE void setTargetBed(const float &celsius) { - target_temperature_bed = celsius; -}; - -FORCE_INLINE bool isHeatingHotend(uint8_t extruder){ - return target_temperature[extruder] > current_temperature[extruder]; -}; - -FORCE_INLINE bool isHeatingBed() { - return target_temperature_bed > current_temperature_bed; -}; - -FORCE_INLINE bool isCoolingHotend(uint8_t extruder) { - return target_temperature[extruder] < current_temperature[extruder]; -}; - -FORCE_INLINE bool isCoolingBed() { - return target_temperature_bed < current_temperature_bed; -}; +FORCE_INLINE bool isCoolingHotend(uint8_t extruder) { return target_temperature[extruder] < current_temperature[extruder]; } +FORCE_INLINE bool isCoolingBed() { return target_temperature_bed < current_temperature_bed; } #define degHotend0() degHotend(0) #define degTargetHotend0() degTargetHotend(0) @@ -141,38 +111,36 @@ FORCE_INLINE bool isCoolingBed() { #define isHeatingHotend0() isHeatingHotend(0) #define isCoolingHotend0() isCoolingHotend(0) #if EXTRUDERS > 1 -#define degHotend1() degHotend(1) -#define degTargetHotend1() degTargetHotend(1) -#define setTargetHotend1(_celsius) setTargetHotend((_celsius), 1) -#define isHeatingHotend1() isHeatingHotend(1) -#define isCoolingHotend1() isCoolingHotend(1) + #define degHotend1() degHotend(1) + #define degTargetHotend1() degTargetHotend(1) + #define setTargetHotend1(_celsius) setTargetHotend((_celsius), 1) + #define isHeatingHotend1() isHeatingHotend(1) + #define isCoolingHotend1() isCoolingHotend(1) #else -#define setTargetHotend1(_celsius) do{}while(0) + #define setTargetHotend1(_celsius) do{}while(0) #endif #if EXTRUDERS > 2 -#define degHotend2() degHotend(2) -#define degTargetHotend2() degTargetHotend(2) -#define setTargetHotend2(_celsius) setTargetHotend((_celsius), 2) -#define isHeatingHotend2() isHeatingHotend(2) -#define isCoolingHotend2() isCoolingHotend(2) + #define degHotend2() degHotend(2) + #define degTargetHotend2() degTargetHotend(2) + #define setTargetHotend2(_celsius) setTargetHotend((_celsius), 2) + #define isHeatingHotend2() isHeatingHotend(2) + #define isCoolingHotend2() isCoolingHotend(2) #else -#define setTargetHotend2(_celsius) do{}while(0) + #define setTargetHotend2(_celsius) do{}while(0) #endif #if EXTRUDERS > 3 -#define degHotend3() degHotend(3) -#define degTargetHotend3() degTargetHotend(3) -#define setTargetHotend3(_celsius) setTargetHotend((_celsius), 3) -#define isHeatingHotend3() isHeatingHotend(3) -#define isCoolingHotend3() isCoolingHotend(3) + #define degHotend3() degHotend(3) + #define degTargetHotend3() degTargetHotend(3) + #define setTargetHotend3(_celsius) setTargetHotend((_celsius), 3) + #define isHeatingHotend3() isHeatingHotend(3) + #define isCoolingHotend3() isCoolingHotend(3) #else -#define setTargetHotend3(_celsius) do{}while(0) + #define setTargetHotend3(_celsius) do{}while(0) #endif #if EXTRUDERS > 4 -#error Invalid number of extruders + #error Invalid number of extruders #endif - - int getHeaterPower(int heater); void disable_heater(); void setWatch(); @@ -189,15 +157,14 @@ static bool thermal_runaway = false; #endif #endif -FORCE_INLINE void autotempShutdown(){ -#ifdef AUTOTEMP - if(autotemp_enabled) - { - autotemp_enabled=false; - if(degTargetHotend(active_extruder)>autotemp_min) - setTargetHotend(0,active_extruder); - } -#endif +FORCE_INLINE void autotempShutdown() { + #ifdef AUTOTEMP + if (autotemp_enabled) { + autotemp_enabled = false; + if (degTargetHotend(active_extruder) > autotemp_min) + setTargetHotend(0, active_extruder); + } + #endif } void PID_autotune(float temp, int extruder, int ncycles);