diff --git a/Marlin/src/config/examples/stm32f103ret6/Configuration.h b/Marlin/src/config/examples/STM32F10/Configuration.h
similarity index 100%
rename from Marlin/src/config/examples/stm32f103ret6/Configuration.h
rename to Marlin/src/config/examples/STM32F10/Configuration.h
diff --git a/Marlin/src/config/examples/STM32F103RET6/Configuration.h b/Marlin/src/config/examples/STM32F103RET6/Configuration.h
deleted file mode 100644
index 90f0c67bc..000000000
--- a/Marlin/src/config/examples/STM32F103RET6/Configuration.h
+++ /dev/null
@@ -1,1731 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * Based on Sprinter and grbl.
- * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see .
- *
- */
-
-/**
- * Configuration.h
- *
- * Basic settings such as:
- *
- * - Type of electronics
- * - Type of temperature sensor
- * - Printer geometry
- * - Endstop configuration
- * - LCD controller
- * - Extra features
- *
- * Advanced settings can be found in Configuration_adv.h
- *
- */
-#ifndef CONFIGURATION_H
-#define CONFIGURATION_H
-#define CONFIGURATION_H_VERSION 020000
-
-//===========================================================================
-//============================= Getting Started =============================
-//===========================================================================
-
-/**
- * Here are some standard links for getting your machine calibrated:
- *
- * http://reprap.org/wiki/Calibration
- * http://youtu.be/wAL9d7FgInk
- * http://calculator.josefprusa.cz
- * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
- * http://www.thingiverse.com/thing:5573
- * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
- * http://www.thingiverse.com/thing:298812
- */
-
-//===========================================================================
-//============================= DELTA Printer ===============================
-//===========================================================================
-// For a Delta printer start with one of the configuration files in the
-// config/examples/delta directory and customize for your machine.
-//
-
-//===========================================================================
-//============================= SCARA Printer ===============================
-//===========================================================================
-// For a SCARA printer start with the configuration files in
-// config/examples/SCARA and customize for your machine.
-//
-
-// @section info
-
-// User-specified version info of this build to display in [Pronterface, etc] terminal window during
-// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
-// build by the user have been successfully uploaded into firmware.
-#define STRING_CONFIG_H_AUTHOR "Victor Perez" // Who made the changes.
-#define SHOW_BOOTSCREEN
-#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION "STM32F103RET6 board" // will be shown during bootup in line 1
-#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
-
-//
-// *** VENDORS PLEASE READ *****************************************************
-//
-// Marlin now allow you to have a vendor boot image to be displayed on machine
-// start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
-// custom boot image and then the default Marlin boot image is shown.
-//
-// We suggest for you to take advantage of this new feature and keep the Marlin
-// boot image unmodified. For an example have a look at the bq Hephestos 2
-// example configuration folder.
-//
-//#define SHOW_CUSTOM_BOOTSCREEN
-// @section machine
-
-/**
- * Select the serial port on the board to use for communication with the host.
- * This allows the connection of wireless adapters (for instance) to non-default port pins.
- * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
- *
- * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
- */
-#define SERIAL_PORT 0
-
-/**
- * This setting determines the communication speed of the printer.
- *
- * 250000 works in most cases, but you might try a lower speed if
- * you commonly experience drop-outs during host printing.
- * You may try up to 1000000 to speed up SD file transfer.
- *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
- */
-#define BAUDRATE 250000
-
-// Enable the Bluetooth serial interface on AT90USB devices
-//#define BLUETOOTH
-
-// The following define selects which electronics board you have.
-// Please choose the name from boards.h that matches your setup
-#ifndef MOTHERBOARD
- #define MOTHERBOARD BOARD_STM32F1R
-#endif
-
-// Optional custom name for your RepStrap or other custom machine
-// Displayed in the LCD "Ready" message
-#define CUSTOM_MACHINE_NAME "CTC i3 Pro B"
-
-// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
-// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
-//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
-
-// @section extruder
-
-// This defines the number of extruders
-// :[1, 2, 3, 4, 5]
-#define EXTRUDERS 1
-
-// For Cyclops or any "multi-extruder" that shares a single nozzle.
-//#define SINGLENOZZLE
-
-/**
- * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
- *
- * This device allows one stepper driver on a control board to drive
- * two to eight stepper motors, one at a time, in a manner suitable
- * for extruders.
- *
- * This option only allows the multiplexer to switch on tool-change.
- * Additional options to configure custom E moves are pending.
- */
-//#define MK2_MULTIPLEXER
-#if ENABLED(MK2_MULTIPLEXER)
- // Override the default DIO selector pins here, if needed.
- // Some pins files may provide defaults for these pins.
- //#define E_MUX0_PIN 40 // Always Required
- //#define E_MUX1_PIN 42 // Needed for 3 to 8 steppers
- //#define E_MUX2_PIN 44 // Needed for 5 to 8 steppers
-#endif
-
-// A dual extruder that uses a single stepper motor
-//#define SWITCHING_EXTRUDER
-#if ENABLED(SWITCHING_EXTRUDER)
- #define SWITCHING_EXTRUDER_SERVO_NR 0
- #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
- #if EXTRUDERS > 3
- #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
- #endif
-#endif
-
-// A dual-nozzle that uses a servomotor to raise/lower one of the nozzles
-//#define SWITCHING_NOZZLE
-#if ENABLED(SWITCHING_NOZZLE)
- #define SWITCHING_NOZZLE_SERVO_NR 0
- #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
- //#define HOTEND_OFFSET_Z { 0.0, 0.0 }
-#endif
-
-/**
- * Two separate X-carriages with extruders that connect to a moving part
- * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
- */
-//#define PARKING_EXTRUDER
-#if ENABLED(PARKING_EXTRUDER)
- #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
- #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
- #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
- #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
- #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
- #define PARKING_EXTRUDER_SECURITY_RAISE 5 // Z-raise before parking
- #define HOTEND_OFFSET_Z { 0.0, 1.3 } // Z-offsets of the two hotends. The first must be 0.
-#endif
-
-/**
- * "Mixing Extruder"
- * - Adds a new code, M165, to set the current mix factors.
- * - Extends the stepping routines to move multiple steppers in proportion to the mix.
- * - Optional support for Repetier Firmware M163, M164, and virtual extruder.
- * - This implementation supports only a single extruder.
- * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
- */
-//#define MIXING_EXTRUDER
-#if ENABLED(MIXING_EXTRUDER)
- #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
- #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
- //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
-#endif
-
-// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
-// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
-// For the other hotends it is their distance from the extruder 0 hotend.
-//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
-//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
-
-// @section machine
-
-/**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
- *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
- */
-#define POWER_SUPPLY 0
-
-#if POWER_SUPPLY > 0
- // Enable this option to leave the PSU off at startup.
- // Power to steppers and heaters will need to be turned on with M80.
- //#define PS_DEFAULT_OFF
-#endif
-
-// @section temperature
-
-//===========================================================================
-//============================= Thermal Settings ============================
-//===========================================================================
-
-/**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
- *
- * Temperature sensors available:
- *
- * -3 : thermocouple with MAX31855 (only for sensor 0)
- * -2 : thermocouple with MAX6675 (only for sensor 0)
- * -1 : thermocouple with AD595
- * 0 : not used
- * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- * 3 : Mendel-parts thermistor (4.7k pullup)
- * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- * 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
- * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- * 10 : 100k RS thermistor 198-961 (4.7k pullup)
- * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
- * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- * 20 : the PT100 circuit found in the Ultimainboard V2.x
- * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- * 66 : 4.7M High Temperature thermistor from Dyze Design
- * 70 : the 100K thermistor found in the bq Hephestos 2
- * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- *
- * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- * (but gives greater accuracy and more stable PID)
- * 51 : 100k thermistor - EPCOS (1k pullup)
- * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- * 1047 : Pt1000 with 4k7 pullup
- * 1010 : Pt1000 with 1k pullup (non standard)
- * 147 : Pt100 with 4k7 pullup
- * 110 : Pt100 with 1k pullup (non standard)
- *
- * Use these for Testing or Development purposes. NEVER for production machine.
- * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
- * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
- *
- * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
- */
-#warning temp_sensor set to 998/999 (fake)
-#define TEMP_SENSOR_0 999
-#define TEMP_SENSOR_1 0
-#define TEMP_SENSOR_2 0
-#define TEMP_SENSOR_3 0
-#define TEMP_SENSOR_4 0
-#define TEMP_SENSOR_BED 998
-
-// Dummy thermistor constant temperature readings, for use with 998 and 999
-#define DUMMY_THERMISTOR_998_VALUE 60
-#define DUMMY_THERMISTOR_999_VALUE 205
-
-// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
-// from the two sensors differ too much the print will be aborted.
-//#define TEMP_SENSOR_1_AS_REDUNDANT
-#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
-
-// Extruder temperature must be close to target for this long before M109 returns success
-#define TEMP_RESIDENCY_TIME 10 // (seconds)
-#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
-#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
-
-// Bed temperature must be close to target for this long before M190 returns success
-#define TEMP_BED_RESIDENCY_TIME 10 // (seconds)
-#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
-#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
-
-// The minimal temperature defines the temperature below which the heater will not be enabled It is used
-// to check that the wiring to the thermistor is not broken.
-// Otherwise this would lead to the heater being powered on all the time.
-#define HEATER_0_MINTEMP 5
-#define HEATER_1_MINTEMP 5
-#define HEATER_2_MINTEMP 5
-#define HEATER_3_MINTEMP 5
-#define HEATER_4_MINTEMP 5
-#define BED_MINTEMP 5
-
-// When temperature exceeds max temp, your heater will be switched off.
-// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
-// You should use MINTEMP for thermistor short/failure protection.
-#define HEATER_0_MAXTEMP 275
-#define HEATER_1_MAXTEMP 275
-#define HEATER_2_MAXTEMP 275
-#define HEATER_3_MAXTEMP 275
-#define HEATER_4_MAXTEMP 275
-#define BED_MAXTEMP 150
-
-//===========================================================================
-//============================= PID Settings ================================
-//===========================================================================
-// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
-
-// Comment the following line to disable PID and enable bang-bang.
-#define PIDTEMP
-#define BANG_MAX 180 // limits current to nozzle while in bang-bang mode; 255=full current
-#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
-#if ENABLED(PIDTEMP)
- #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
- //#define PID_DEBUG // Sends debug data to the serial port.
- //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
- //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
- //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
- // Set/get with gcode: M301 E[extruder number, 0-2]
- #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
- // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
- #define K1 0.95 //smoothing factor within the PID
-
- // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
-
- // Ultimaker
- #define DEFAULT_Kp 22.2
- #define DEFAULT_Ki 1.08
- #define DEFAULT_Kd 114
-
- // MakerGear
- //#define DEFAULT_Kp 7.0
- //#define DEFAULT_Ki 0.1
- //#define DEFAULT_Kd 12
-
- // Mendel Parts V9 on 12V
- //#define DEFAULT_Kp 63.0
- //#define DEFAULT_Ki 2.25
- //#define DEFAULT_Kd 440
-
-#endif // PIDTEMP
-
-//===========================================================================
-//============================= PID > Bed Temperature Control ===============
-//===========================================================================
-// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
-//
-// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
-// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
-// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
-// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
-// If your configuration is significantly different than this and you don't understand the issues involved, you probably
-// shouldn't use bed PID until someone else verifies your hardware works.
-// If this is enabled, find your own PID constants below.
-//#define PIDTEMPBED
-
-//#define BED_LIMIT_SWITCHING
-
-// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
-// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
-// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
-// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
-#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
-
-#if ENABLED(PIDTEMPBED)
-
- //#define PID_BED_DEBUG // Sends debug data to the serial port.
-
- //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
- //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
- #define DEFAULT_bedKp 10.00
- #define DEFAULT_bedKi .023
- #define DEFAULT_bedKd 305.4
-
- //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
- //from pidautotune
- //#define DEFAULT_bedKp 97.1
- //#define DEFAULT_bedKi 1.41
- //#define DEFAULT_bedKd 1675.16
-
- // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
-#endif // PIDTEMPBED
-
-// @section extruder
-
-// This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP.
-// It also enables the M302 command to set the minimum extrusion temperature
-// or to allow moving the extruder regardless of the hotend temperature.
-// *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
-#define PREVENT_COLD_EXTRUSION
-#define EXTRUDE_MINTEMP 170
-
-// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
-// Note that for Bowden Extruders a too-small value here may prevent loading.
-#define PREVENT_LENGTHY_EXTRUDE
-#define EXTRUDE_MAXLENGTH 200
-
-//===========================================================================
-//======================== Thermal Runaway Protection =======================
-//===========================================================================
-
-/**
- * Thermal Protection protects your printer from damage and fire if a
- * thermistor falls out or temperature sensors fail in any way.
- *
- * The issue: If a thermistor falls out or a temperature sensor fails,
- * Marlin can no longer sense the actual temperature. Since a disconnected
- * thermistor reads as a low temperature, the firmware will keep the heater on.
- *
- * If you get "Thermal Runaway" or "Heating failed" errors the
- * details can be tuned in Configuration_adv.h
- */
-
-#warning "disabled temperature protection"
-//#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
-//#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
-
-//===========================================================================
-//============================= Mechanical Settings =========================
-//===========================================================================
-
-// @section machine
-
-// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
-// either in the usual order or reversed
-//#define COREXY
-//#define COREXZ
-//#define COREYZ
-//#define COREYX
-//#define COREZX
-//#define COREZY
-
-//===========================================================================
-//============================== Endstop Settings ===========================
-//===========================================================================
-
-// @section homing
-
-// Specify here all the endstop connectors that are connected to any endstop or probe.
-// Almost all printers will be using one per axis. Probes will use one or more of the
-// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
-#define USE_XMIN_PLUG
-#define USE_YMIN_PLUG
-#define USE_ZMIN_PLUG
-//#define USE_XMAX_PLUG
-//#define USE_YMAX_PLUG
-//#define USE_ZMAX_PLUG
-
-// coarse Endstop Settings
-#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
-
-#if DISABLED(ENDSTOPPULLUPS)
- // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
- //#define ENDSTOPPULLUP_XMAX
- //#define ENDSTOPPULLUP_YMAX
- //#define ENDSTOPPULLUP_ZMAX
- //#define ENDSTOPPULLUP_XMIN
- //#define ENDSTOPPULLUP_YMIN
- //#define ENDSTOPPULLUP_ZMIN
- //#define ENDSTOPPULLUP_ZMIN_PROBE
-#endif
-
-// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
-
-// Enable this feature if all enabled endstop pins are interrupt-capable.
-// This will remove the need to poll the interrupt pins, saving many CPU cycles.
-//#define ENDSTOP_INTERRUPTS_FEATURE
-
-//=============================================================================
-//============================== Movement Settings ============================
-//=============================================================================
-// @section motion
-
-/**
- * Default Settings
- *
- * These settings can be reset by M502
- *
- * Note that if EEPROM is enabled, saved values will override these.
- */
-
-/**
- * With this option each E stepper can have its own factors for the
- * following movement settings. If fewer factors are given than the
- * total number of extruders, the last value applies to the rest.
- */
-//#define DISTINCT_E_FACTORS
-
-/**
- * Default Axis Steps Per Unit (steps/mm)
- * Override with M92
- * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
- */
-#define DEFAULT_AXIS_STEPS_PER_UNIT { 78.74, 78.74, 2560, 105.0 }
-
-/**
- * Default Max Feed Rate (mm/s)
- * Override with M203
- * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
- */
-#define DEFAULT_MAX_FEEDRATE { 400, 400, 2, 45 }
-
-/**
- * Default Max Acceleration (change/s) change = mm/s
- * (Maximum start speed for accelerated moves)
- * Override with M201
- * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
- */
-#define DEFAULT_MAX_ACCELERATION { 1400, 1400, 100, 80000 }
-
-/**
- * Default Acceleration (change/s) change = mm/s
- * Override with M204
- *
- * M204 P Acceleration
- * M204 R Retract Acceleration
- * M204 T Travel Acceleration
- */
-#define DEFAULT_ACCELERATION 1400 // X, Y, Z and E acceleration for printing moves
-#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration for retracts
-#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
-
-/**
- * Default Jerk (mm/s)
- * Override with M205 X Y Z E
- *
- * "Jerk" specifies the minimum speed change that requires acceleration.
- * When changing speed and direction, if the difference is less than the
- * value set here, it may happen instantaneously.
- */
-#define DEFAULT_XJERK 13.0
-#define DEFAULT_YJERK 13.0
-#define DEFAULT_ZJERK 0.3
-#define DEFAULT_EJERK 5.0
-
-
-//===========================================================================
-//============================= Z Probe Options =============================
-//===========================================================================
-// @section probes
-
-//
-// See http://marlinfw.org/configuration/probes.html
-//
-
-/**
- * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
- *
- * Enable this option for a probe connected to the Z Min endstop pin.
- */
-#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
-
-/**
- * Z_MIN_PROBE_ENDSTOP
- *
- * Enable this option for a probe connected to any pin except Z-Min.
- * (By default Marlin assumes the Z-Max endstop pin.)
- * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
- *
- * - The simplest option is to use a free endstop connector.
- * - Use 5V for powered (usually inductive) sensors.
- *
- * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
- * - For simple switches connect...
- * - normally-closed switches to GND and D32.
- * - normally-open switches to 5V and D32.
- *
- * WARNING: Setting the wrong pin may have unexpected and potentially
- * disastrous consequences. Use with caution and do your homework.
- *
- */
-//#define Z_MIN_PROBE_ENDSTOP
-
-/**
- * Probe Type
- *
- * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
- * Activate one of these to use Auto Bed Leveling below.
- */
-
-/**
- * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
- * Use G29 repeatedly, adjusting the Z height at each point with movement commands
- * or (with LCD_BED_LEVELING) the LCD controller.
- */
-//#define PROBE_MANUALLY
-
-/**
- * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
- * (e.g., an inductive probe or a nozzle-based probe-switch.)
- */
-//#define FIX_MOUNTED_PROBE
-
-/**
- * Z Servo Probe, such as an endstop switch on a rotating arm.
- */
-//#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector.
-//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
-
-/**
- * The BLTouch probe uses a Hall effect sensor and emulates a servo.
- */
-//#define BLTOUCH
-#if ENABLED(BLTOUCH)
- //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed
-#endif
-
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF // Turn heaters off when probing
-//#define PROBING_FANS_OFF // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
-
-// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
-//#define SOLENOID_PROBE
-
-// A sled-mounted probe like those designed by Charles Bell.
-//#define Z_PROBE_SLED
-//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
-
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
-
-/**
- * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
- * X and Y offsets must be integers.
- *
- * In the following example the X and Y offsets are both positive:
- * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
- * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
- *
- * +-- BACK ---+
- * | |
- * L | (+) P | R <-- probe (20,20)
- * E | | I
- * F | (-) N (+) | G <-- nozzle (10,10)
- * T | | H
- * | (-) | T
- * | |
- * O-- FRONT --+
- * (0,0)
- */
-#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle]
-#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
-#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
-
-// X and Y axis travel speed (mm/m) between probes
-#define XY_PROBE_SPEED 8000
-
-// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
-#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
-
-// Speed for the "accurate" probe of each point
-#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
-
-// Use double touch for probing
-//#define PROBE_DOUBLE_TOUCH
-
-/**
- * Z probes require clearance when deploying, stowing, and moving between
- * probe points to avoid hitting the bed and other hardware.
- * Servo-mounted probes require extra space for the arm to rotate.
- * Inductive probes need space to keep from triggering early.
- *
- * Use these settings to specify the distance (mm) to raise the probe (or
- * lower the bed). The values set here apply over and above any (negative)
- * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
- * Only integer values >= 1 are valid here.
- *
- * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
- * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
- */
-#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
-#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
-
-// For M851 give a range for adjusting the Z probe offset
-#define Z_PROBE_OFFSET_RANGE_MIN -20
-#define Z_PROBE_OFFSET_RANGE_MAX 20
-
-// Enable the M48 repeatability test to test probe accuracy
-//#define Z_MIN_PROBE_REPEATABILITY_TEST
-
-// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
-// :{ 0:'Low', 1:'High' }
-#define X_ENABLE_ON 0
-#define Y_ENABLE_ON 0
-#define Z_ENABLE_ON 0
-#define E_ENABLE_ON 0 // For all extruders
-
-// Disables axis stepper immediately when it's not being used.
-// WARNING: When motors turn off there is a chance of losing position accuracy!
-#define DISABLE_X false
-#define DISABLE_Y false
-#define DISABLE_Z false
-// Warn on display about possibly reduced accuracy
-//#define DISABLE_REDUCED_ACCURACY_WARNING
-
-// @section extruder
-
-#define DISABLE_E false // For all extruders
-#define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled.
-
-// @section machine
-
-// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR false
-#define INVERT_Y_DIR true
-#define INVERT_Z_DIR false
-
-// Enable this option for Toshiba stepper drivers
-//#define CONFIG_STEPPERS_TOSHIBA
-
-// @section extruder
-
-// For direct drive extruder v9 set to true, for geared extruder set to false.
-#define INVERT_E0_DIR true
-#define INVERT_E1_DIR false
-#define INVERT_E2_DIR false
-#define INVERT_E3_DIR false
-#define INVERT_E4_DIR false
-
-// @section homing
-
-//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
-
-//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
- // Be sure you have this distance over your Z_MAX_POS in case.
-
-// Direction of endstops when homing; 1=MAX, -1=MIN
-// :[-1,1]
-#define X_HOME_DIR -1
-#define Y_HOME_DIR -1
-#define Z_HOME_DIR -1
-
-// @section machine
-
-// The size of the print bed
-#define X_BED_SIZE 200
-#define Y_BED_SIZE 200
-
-// Travel limits (mm) after homing, corresponding to endstop positions.
-#define X_MIN_POS 0
-#define Y_MIN_POS 0
-#define Z_MIN_POS 0
-#define X_MAX_POS X_BED_SIZE
-#define Y_MAX_POS Y_BED_SIZE
-#define Z_MAX_POS 180
-
-/**
- * Software Endstops
- *
- * - Prevent moves outside the set machine bounds.
- * - Individual axes can be disabled, if desired.
- * - X and Y only apply to Cartesian robots.
- * - Use 'M211' to set software endstops on/off or report current state
- */
-
-// Min software endstops constrain movement within minimum coordinate bounds
-#define MIN_SOFTWARE_ENDSTOPS
-#if ENABLED(MIN_SOFTWARE_ENDSTOPS)
- #define MIN_SOFTWARE_ENDSTOP_X
- #define MIN_SOFTWARE_ENDSTOP_Y
- #define MIN_SOFTWARE_ENDSTOP_Z
-#endif
-
-// Max software endstops constrain movement within maximum coordinate bounds
-#define MAX_SOFTWARE_ENDSTOPS
-#if ENABLED(MAX_SOFTWARE_ENDSTOPS)
- #define MAX_SOFTWARE_ENDSTOP_X
- #define MAX_SOFTWARE_ENDSTOP_Y
- #define MAX_SOFTWARE_ENDSTOP_Z
-#endif
-
-/**
- * Filament Runout Sensor
- * A mechanical or opto endstop is used to check for the presence of filament.
- *
- * RAMPS-based boards use SERVO3_PIN.
- * For other boards you may need to define FIL_RUNOUT_PIN.
- * By default the firmware assumes HIGH = has filament, LOW = ran out
- */
-//#define FILAMENT_RUNOUT_SENSOR
-#if ENABLED(FILAMENT_RUNOUT_SENSOR)
- #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
- #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
- #define FILAMENT_RUNOUT_SCRIPT "M600"
-#endif
-
-//===========================================================================
-//=============================== Bed Leveling ==============================
-//===========================================================================
-// @section bedlevel
-
-/**
- * Choose one of the options below to enable G29 Bed Leveling. The parameters
- * and behavior of G29 will change depending on your selection.
- *
- * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
- *
- * - AUTO_BED_LEVELING_3POINT
- * Probe 3 arbitrary points on the bed (that aren't collinear)
- * You specify the XY coordinates of all 3 points.
- * The result is a single tilted plane. Best for a flat bed.
- *
- * - AUTO_BED_LEVELING_LINEAR
- * Probe several points in a grid.
- * You specify the rectangle and the density of sample points.
- * The result is a single tilted plane. Best for a flat bed.
- *
- * - AUTO_BED_LEVELING_BILINEAR
- * Probe several points in a grid.
- * You specify the rectangle and the density of sample points.
- * The result is a mesh, best for large or uneven beds.
- *
- * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
- * A comprehensive bed leveling system combining the features and benefits
- * of other systems. UBL also includes integrated Mesh Generation, Mesh
- * Validation and Mesh Editing systems.
- *
- * - MESH_BED_LEVELING
- * Probe a grid manually
- * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
- * For machines without a probe, Mesh Bed Leveling provides a method to perform
- * leveling in steps so you can manually adjust the Z height at each grid-point.
- * With an LCD controller the process is guided step-by-step.
- */
-//#define AUTO_BED_LEVELING_3POINT
-//#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
-//#define AUTO_BED_LEVELING_UBL
-//#define MESH_BED_LEVELING
-
-/**
- * Enable detailed logging of G28, G29, M48, etc.
- * Turn on with the command 'M111 S32'.
- * NOTE: Requires a lot of PROGMEM!
- */
-//#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY // enable a graphics overly while editing the mesh from auto-level
-
-#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
- // Gradually reduce leveling correction until a set height is reached,
- // at which point movement will be level to the machine's XY plane.
- // The height can be set with M420 Z
- #define ENABLE_LEVELING_FADE_HEIGHT
-#endif
-
-#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
-
- // Set the number of grid points per dimension.
- #define GRID_MAX_POINTS_X 3
- #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
-
- // Set the boundaries for probing (where the probe can reach).
- #define LEFT_PROBE_BED_POSITION 15
- #define RIGHT_PROBE_BED_POSITION 170
- #define FRONT_PROBE_BED_POSITION 20
- #define BACK_PROBE_BED_POSITION 170
-
- // The Z probe minimum outer margin (to validate G29 parameters).
- #define MIN_PROBE_EDGE 10
-
- // Probe along the Y axis, advancing X after each column
- //#define PROBE_Y_FIRST
-
- #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
-
- // Beyond the probed grid, continue the implied tilt?
- // Default is to maintain the height of the nearest edge.
- //#define EXTRAPOLATE_BEYOND_GRID
-
- //
- // Experimental Subdivision of the grid by Catmull-Rom method.
- // Synthesizes intermediate points to produce a more detailed mesh.
- //
- //#define ABL_BILINEAR_SUBDIVISION
- #if ENABLED(ABL_BILINEAR_SUBDIVISION)
- // Number of subdivisions between probe points
- #define BILINEAR_SUBDIVISIONS 3
- #endif
-
- #endif
-
-#elif ENABLED(AUTO_BED_LEVELING_3POINT)
-
- // 3 arbitrary points to probe.
- // A simple cross-product is used to estimate the plane of the bed.
- #define ABL_PROBE_PT_1_X 15
- #define ABL_PROBE_PT_1_Y 180
- #define ABL_PROBE_PT_2_X 15
- #define ABL_PROBE_PT_2_Y 20
- #define ABL_PROBE_PT_3_X 170
- #define ABL_PROBE_PT_3_Y 20
-
-#elif ENABLED(AUTO_BED_LEVELING_UBL)
-
- //===========================================================================
- //========================= Unified Bed Leveling ============================
- //===========================================================================
-
- #define MESH_INSET 1 // Mesh inset margin on print area
- #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
- #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
-
- #define UBL_PROBE_PT_1_X 39 // Probing points for 3-Point leveling of the mesh
- #define UBL_PROBE_PT_1_Y 180
- #define UBL_PROBE_PT_2_X 39
- #define UBL_PROBE_PT_2_Y 20
- #define UBL_PROBE_PT_3_X 180
- #define UBL_PROBE_PT_3_Y 20
-
- //#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
- #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
- #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
-
-#elif ENABLED(MESH_BED_LEVELING)
-
- //===========================================================================
- //=================================== Mesh ==================================
- //===========================================================================
-
- #define MESH_INSET 10 // Mesh inset margin on print area
- #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
- #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
-
- //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
-
-#endif // BED_LEVELING
-
-/**
- * Use the LCD controller for bed leveling
- * Requires MESH_BED_LEVELING or PROBE_MANUALLY
- */
-//#define LCD_BED_LEVELING
-
-#if ENABLED(LCD_BED_LEVELING)
- #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
- #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
-#endif
-
-// Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
-
-/**
- * Commands to execute at the end of G29 probing.
- * Useful to retract or move the Z probe out of the way.
- */
-//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
-
-
-// @section homing
-
-// The center of the bed is at (X=0, Y=0)
-//#define BED_CENTER_AT_0_0
-
-// Manually set the home position. Leave these undefined for automatic settings.
-// For DELTA this is the top-center of the Cartesian print volume.
-//#define MANUAL_X_HOME_POS 0
-//#define MANUAL_Y_HOME_POS 0
-//#define MANUAL_Z_HOME_POS 0
-
-// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
-//
-// With this feature enabled:
-//
-// - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
-// - If stepper drivers time out, it will need X and Y homing again before Z homing.
-// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
-// - Prevent Z homing when the Z probe is outside bed area.
-//
-//#define Z_SAFE_HOMING
-
-#if ENABLED(Z_SAFE_HOMING)
- #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
- #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
-#endif
-
-// Homing speeds (mm/m)
-#define HOMING_FEEDRATE_XY (50*60)
-#define HOMING_FEEDRATE_Z (4*60)
-
-//=============================================================================
-//============================= Additional Features ===========================
-//=============================================================================
-
-// @section extras
-
-//
-// EEPROM
-//
-// The microcontroller can store settings in the EEPROM, e.g. max velocity...
-// M500 - stores parameters in EEPROM
-// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
-// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
-//
-#define EEPROM_SETTINGS // Enable for M500 and M501 commands
-//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
-//#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
-
-//
-// Host Keepalive
-//
-// When enabled Marlin will send a busy status message to the host
-// every couple of seconds when it can't accept commands.
-//
-#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
-#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
-#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
-
-//
-// M100 Free Memory Watcher
-//
-//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage
-
-//
-// G20/G21 Inch mode support
-//
-//#define INCH_MODE_SUPPORT
-
-//
-// M149 Set temperature units support
-//
-#define TEMPERATURE_UNITS_SUPPORT
-
-// @section temperature
-
-// Preheat Constants
-#define PREHEAT_1_TEMP_HOTEND 200
-#define PREHEAT_1_TEMP_BED 60
-#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
-
-#define PREHEAT_2_TEMP_HOTEND 220
-#define PREHEAT_2_TEMP_BED 100
-#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
-
-/**
- * Nozzle Park -- EXPERIMENTAL
- *
- * Park the nozzle at the given XYZ position on idle or G27.
- *
- * The "P" parameter controls the action applied to the Z axis:
- *
- * P0 (Default) If Z is below park Z raise the nozzle.
- * P1 Raise the nozzle always to Z-park height.
- * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
- */
-//#define NOZZLE_PARK_FEATURE
-
-#if ENABLED(NOZZLE_PARK_FEATURE)
- // Specify a park position as { X, Y, Z }
- #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
-#endif
-
-/**
- * Clean Nozzle Feature -- EXPERIMENTAL
- *
- * Adds the G12 command to perform a nozzle cleaning process.
- *
- * Parameters:
- * P Pattern
- * S Strokes / Repetitions
- * T Triangles (P1 only)
- *
- * Patterns:
- * P0 Straight line (default). This process requires a sponge type material
- * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
- * between the start / end points.
- *
- * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
- * number of zig-zag triangles to do. "S" defines the number of strokes.
- * Zig-zags are done in whichever is the narrower dimension.
- * For example, "G12 P1 S1 T3" will execute:
- *
- * --
- * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
- * | | / \ / \ / \ |
- * A | | / \ / \ / \ |
- * | | / \ / \ / \ |
- * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
- * -- +--------------------------------+
- * |________|_________|_________|
- * T1 T2 T3
- *
- * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
- * "R" specifies the radius. "S" specifies the stroke count.
- * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
- *
- * Caveats: The ending Z should be the same as starting Z.
- * Attention: EXPERIMENTAL. G-code arguments may change.
- *
- */
-//#define NOZZLE_CLEAN_FEATURE
-
-#if ENABLED(NOZZLE_CLEAN_FEATURE)
- // Default number of pattern repetitions
- #define NOZZLE_CLEAN_STROKES 12
-
- // Default number of triangles
- #define NOZZLE_CLEAN_TRIANGLES 3
-
- // Specify positions as { X, Y, Z }
- #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
- #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
-
- // Circular pattern radius
- #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
- // Circular pattern circle fragments number
- #define NOZZLE_CLEAN_CIRCLE_FN 10
- // Middle point of circle
- #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
-
- // Moves the nozzle to the initial position
- #define NOZZLE_CLEAN_GOBACK
-#endif
-
-/**
- * Print Job Timer
- *
- * Automatically start and stop the print job timer on M104/M109/M190.
- *
- * M104 (hotend, no wait) - high temp = none, low temp = stop timer
- * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
- * M190 (bed, wait) - high temp = start timer, low temp = none
- *
- * The timer can also be controlled with the following commands:
- *
- * M75 - Start the print job timer
- * M76 - Pause the print job timer
- * M77 - Stop the print job timer
- */
-#define PRINTJOB_TIMER_AUTOSTART
-
-/**
- * Print Counter
- *
- * Track statistical data such as:
- *
- * - Total print jobs
- * - Total successful print jobs
- * - Total failed print jobs
- * - Total time printing
- *
- * View the current statistics with M78.
- */
-//#define PRINTCOUNTER
-
-//=============================================================================
-//============================= LCD and SD support ============================
-//=============================================================================
-
-// @section lcd
-
-/**
- * LCD LANGUAGE
- *
- * Select the language to display on the LCD. These languages are available:
- *
- * en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, eu, fi, fr, fr_utf8, gl,
- * hr, it, kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8,
- * tr, uk, zh_CN, zh_TW, test
- *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', test':'TEST' }
- */
-#define LCD_LANGUAGE en
-
-/**
- * LCD Character Set
- *
- * Note: This option is NOT applicable to Graphical Displays.
- *
- * All character-based LCDs provide ASCII plus one of these
- * language extensions:
- *
- * - JAPANESE ... the most common
- * - WESTERN ... with more accented characters
- * - CYRILLIC ... for the Russian language
- *
- * To determine the language extension installed on your controller:
- *
- * - Compile and upload with LCD_LANGUAGE set to 'test'
- * - Click the controller to view the LCD menu
- * - The LCD will display Japanese, Western, or Cyrillic text
- *
- * See http://marlinfw.org/docs/development/lcd_language.html
- *
- * :['JAPANESE', 'WESTERN', 'CYRILLIC']
- */
-#define DISPLAY_CHARSET_HD44780 JAPANESE
-
-/**
- * LCD TYPE
- *
- * Enable ULTRA_LCD for a 16x2, 16x4, 20x2, or 20x4 character-based LCD.
- * Enable DOGLCD for a 128x64 (ST7565R) Full Graphical Display.
- * (These options will be enabled automatically for most displays.)
- *
- * IMPORTANT: The U8glib library is required for Full Graphic Display!
- * https://github.com/olikraus/U8glib_Arduino
- */
-//#define ULTRA_LCD // Character based
-//#define DOGLCD // Full graphics display
-
-/**
- * SD CARD
- *
- * SD Card support is disabled by default. If your controller has an SD slot,
- * you must uncomment the following option or it won't work.
- *
- */
-#define SDSUPPORT
-
-/**
- * SD CARD: SPI SPEED
- *
- * Enable one of the following items for a slower SPI transfer speed.
- * This may be required to resolve "volume init" errors.
- */
-//#define SPI_SPEED SPI_HALF_SPEED
-//#define SPI_SPEED SPI_QUARTER_SPEED
-//#define SPI_SPEED SPI_EIGHTH_SPEED
-
-/**
- * SD CARD: ENABLE CRC
- *
- * Use CRC checks and retries on the SD communication.
- */
-//#define SD_CHECK_AND_RETRY
-
-//
-// ENCODER SETTINGS
-//
-// This option overrides the default number of encoder pulses needed to
-// produce one step. Should be increased for high-resolution encoders.
-//
-//#define ENCODER_PULSES_PER_STEP 1
-
-//
-// Use this option to override the number of step signals required to
-// move between next/prev menu items.
-//
-//#define ENCODER_STEPS_PER_MENU_ITEM 5
-
-/**
- * Encoder Direction Options
- *
- * Test your encoder's behavior first with both options disabled.
- *
- * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
- * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
- * Reversed Value Editing only? Enable BOTH options.
- */
-
-//
-// This option reverses the encoder direction everywhere.
-//
-// Set this option if CLOCKWISE causes values to DECREASE
-//
-//#define REVERSE_ENCODER_DIRECTION
-
-//
-// This option reverses the encoder direction for navigating LCD menus.
-//
-// If CLOCKWISE normally moves DOWN this makes it go UP.
-// If CLOCKWISE normally moves UP this makes it go DOWN.
-//
-//#define REVERSE_MENU_DIRECTION
-
-//
-// Individual Axis Homing
-//
-// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
-//
-//#define INDIVIDUAL_AXIS_HOMING_MENU
-
-//
-// SPEAKER/BUZZER
-//
-// If you have a speaker that can produce tones, enable it here.
-// By default Marlin assumes you have a buzzer with a fixed frequency.
-//
-//#define SPEAKER
-
-//
-// The duration and frequency for the UI feedback sound.
-// Set these to 0 to disable audio feedback in the LCD menus.
-//
-// Note: Test audio output with the G-Code:
-// M300 S P
-//
-//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
-//#define LCD_FEEDBACK_FREQUENCY_HZ 1000
-
-//
-// CONTROLLER TYPE: Standard
-//
-// Marlin supports a wide variety of controllers.
-// Enable one of the following options to specify your controller.
-//
-
-//
-// ULTIMAKER Controller.
-//
-//#define ULTIMAKERCONTROLLER
-
-//
-// ULTIPANEL as seen on Thingiverse.
-//
-//#define ULTIPANEL
-
-//
-// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
-// http://reprap.org/wiki/PanelOne
-//
-//#define PANEL_ONE
-
-//
-// MaKr3d Makr-Panel with graphic controller and SD support.
-// http://reprap.org/wiki/MaKr3d_MaKrPanel
-//
-//#define MAKRPANEL
-
-//
-// ReprapWorld Graphical LCD
-// https://reprapworld.com/?products_details&products_id/1218
-//
-//#define REPRAPWORLD_GRAPHICAL_LCD
-
-//
-// Activate one of these if you have a Panucatt Devices
-// Viki 2.0 or mini Viki with Graphic LCD
-// http://panucatt.com
-//
-//#define VIKI2
-//#define miniVIKI
-
-//
-// Adafruit ST7565 Full Graphic Controller.
-// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
-//
-//#define ELB_FULL_GRAPHIC_CONTROLLER
-
-//
-// RepRapDiscount Smart Controller.
-// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
-//
-// Note: Usually sold with a white PCB.
-//
-//#define REPRAP_DISCOUNT_SMART_CONTROLLER
-
-//
-// GADGETS3D G3D LCD/SD Controller
-// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
-//
-// Note: Usually sold with a blue PCB.
-//
-//#define G3D_PANEL
-
-//
-// RepRapDiscount FULL GRAPHIC Smart Controller
-// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
-//
-//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
-
-//
-// MakerLab Mini Panel with graphic
-// controller and SD support - http://reprap.org/wiki/Mini_panel
-//
-//#define MINIPANEL
-
-//
-// RepRapWorld REPRAPWORLD_KEYPAD v1.1
-// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
-//
-// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
-// is pressed, a value of 10.0 means 10mm per click.
-//
-//#define REPRAPWORLD_KEYPAD
-//#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
-
-//
-// RigidBot Panel V1.0
-// http://www.inventapart.com/
-//
-//#define RIGIDBOT_PANEL
-
-//
-// BQ LCD Smart Controller shipped by
-// default with the BQ Hephestos 2 and Witbox 2.
-//
-//#define BQ_LCD_SMART_CONTROLLER
-
-//
-// Cartesio UI
-// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
-//
-//#define CARTESIO_UI
-
-//
-// ANET_10 Controller supported displays.
-//
-//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
- // This LCD is known to be susceptible to electrical interference
- // which scrambles the display. Pressing any button clears it up.
-//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
- // A clone of the RepRapDiscount full graphics display but with
- // different pins/wiring (see pins_ANET_10.h).
-
-//
-// LCD for Melzi Card with Graphical LCD
-//
-//#define LCD_FOR_MELZI
-
-//
-// CONTROLLER TYPE: I2C
-//
-// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
-// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
-//
-
-//
-// Elefu RA Board Control Panel
-// http://www.elefu.com/index.php?route=product/product&product_id=53
-//
-//#define RA_CONTROL_PANEL
-
-//
-// Sainsmart YW Robot (LCM1602) LCD Display
-//
-// Note: This controller requires F.Malpartida's LiquidCrystal_I2C library
-// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
-//
-//#define LCD_I2C_SAINSMART_YWROBOT
-
-//
-// Generic LCM1602 LCD adapter
-//
-//#define LCM1602
-
-//
-// PANELOLU2 LCD with status LEDs,
-// separate encoder and click inputs.
-//
-// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
-// For more info: https://github.com/lincomatic/LiquidTWI2
-//
-// Note: The PANELOLU2 encoder click input can either be directly connected to
-// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
-//
-//#define LCD_I2C_PANELOLU2
-
-//
-// Panucatt VIKI LCD with status LEDs,
-// integrated click & L/R/U/D buttons, separate encoder inputs.
-//
-//#define LCD_I2C_VIKI
-
-//
-// SSD1306 OLED full graphics generic display
-//
-//#define U8GLIB_SSD1306
-
-//
-// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
-//
-//#define SAV_3DGLCD
-#if ENABLED(SAV_3DGLCD)
- //#define U8GLIB_SSD1306
- #define U8GLIB_SH1106
-#endif
-
-//
-// CONTROLLER TYPE: Shift register panels
-//
-// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
-// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
-//
-//#define SAV_3DLCD
-
-//
-// TinyBoy2 128x64 OLED / Encoder Panel
-//
-//#define OLED_PANEL_TINYBOY2
-
-//
-// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
-// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
-//
-//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
-
-//
-// MKS MINI12864 with graphic controller and SD support
-// http://reprap.org/wiki/MKS_MINI_12864
-//
-//#define MKS_MINI_12864
-
-//
-// Factory display for Creality CR-10
-// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
-//
-// This is RAMPS-compatible using a single 10-pin connector.
-// (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
-//
-//#define CR10_STOCKDISPLAY
-
-//
-// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
-// http://reprap.org/wiki/MKS_12864OLED
-//
-// Tiny, but very sharp OLED display
-//
-//#define MKS_12864OLED
-
-//
-// AZSMZ 12864 LCD with SD
-// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html
-//
-//#define AZSMZ_12864
-
-// Silvergate GLCD controller
-// http://github.com/android444/Silvergate
-//
-//#define SILVER_GATE_GLCD_CONTROLLER
-
-//=============================================================================
-//=============================== Extra Features ==============================
-//=============================================================================
-
-// @section extras
-
-// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
-//#define FAST_PWM_FAN
-
-// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
-// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
-// is too low, you should also increment SOFT_PWM_SCALE.
-//#define FAN_SOFT_PWM
-
-// Incrementing this by 1 will double the software PWM frequency,
-// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
-// However, control resolution will be halved for each increment;
-// at zero value, there are 128 effective control positions.
-#define SOFT_PWM_SCALE 0
-
-// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
-// be used to mitigate the associated resolution loss. If enabled,
-// some of the PWM cycles are stretched so on average the desired
-// duty cycle is attained.
-//#define SOFT_PWM_DITHER
-
-// Temperature status LEDs that display the hotend and bed temperature.
-// If all hotends, bed temperature, and target temperature are under 54C
-// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
-//#define TEMP_STAT_LEDS
-
-// M240 Triggers a camera by emulating a Canon RC-1 Remote
-// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
-//#define PHOTOGRAPH_PIN 23
-
-// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
-//#define SF_ARC_FIX
-
-// Support for the BariCUDA Paste Extruder
-//#define BARICUDA
-
-// Support for BlinkM/CyzRgb
-//#define BLINKM
-
-// Support for PCA9632 PWM LED driver
-//#define PCA9632
-
-/**
- * RGB LED / LED Strip Control
- *
- * Enable support for an RGB LED connected to 5V digital pins, or
- * an RGB Strip connected to MOSFETs controlled by digital pins.
- *
- * Adds the M150 command to set the LED (or LED strip) color.
- * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
- * luminance values can be set from 0 to 255.
- * For Neopixel LED an overall brightness parameter is also available.
- *
- * *** CAUTION ***
- * LED Strips require a MOFSET Chip between PWM lines and LEDs,
- * as the Arduino cannot handle the current the LEDs will require.
- * Failure to follow this precaution can destroy your Arduino!
- * NOTE: A separate 5V power supply is required! The Neopixel LED needs
- * more current than the Arduino 5V linear regulator can produce.
- * *** CAUTION ***
- *
- * LED Type. Enable only one of the following two options.
- *
- */
-
-//#define RGB_LED
-//#define RGBW_LED
-#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
- #define RGB_LED_R_PIN 34
- #define RGB_LED_G_PIN 43
- #define RGB_LED_B_PIN 35
- #define RGB_LED_W_PIN -1
-#endif
-
-// Support for Adafruit Neopixel LED driver
-//#define NEOPIXEL_LED
-#if ENABLED(NEOPIXEL_LED)
- #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
- #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
- #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
- #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
- #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
- //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
-#endif
-
-/**
- * Printer Event LEDs
- *
- * During printing, the LEDs will reflect the printer status:
- *
- * - Gradually change from blue to violet as the heated bed gets to target temp
- * - Gradually change from violet to red as the hotend gets to temperature
- * - Change to white to illuminate work surface
- * - Change to green once print has finished
- * - Turn off after the print has finished and the user has pushed a button
- */
-#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
- #define PRINTER_EVENT_LEDS
-#endif
-
-/**
- * R/C SERVO support
- * Sponsored by TrinityLabs, Reworked by codexmas
- */
-
-/**
- * Number of servos
- *
- * For some servo-related options NUM_SERVOS will be set automatically.
- * Set this manually if there are extra servos needing manual control.
- * Leave undefined or set to 0 to entirely disable the servo subsystem.
- */
-//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
-
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
-// 300ms is a good value but you can try less delay.
-// If the servo can't reach the requested position, increase it.
-#define SERVO_DELAY { 300 }
-
-// Servo deactivation
-//
-// With this option servos are powered only during movement, then turned off to prevent jitter.
-//#define DEACTIVATE_SERVOS_AFTER_MOVE
-
-/**
- * Filament Width Sensor
- *
- * Measures the filament width in real-time and adjusts
- * flow rate to compensate for any irregularities.
- *
- * Also allows the measured filament diameter to set the
- * extrusion rate, so the slicer only has to specify the
- * volume.
- *
- * Only a single extruder is supported at this time.
- *
- * 34 RAMPS_14 : Analog input 5 on the AUX2 connector
- * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
- * 301 RAMBO : Analog input 3
- *
- * Note: May require analog pins to be defined for other boards.
- */
-//#define FILAMENT_WIDTH_SENSOR
-
-#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
-
-#if ENABLED(FILAMENT_WIDTH_SENSOR)
- #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
- #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
-
- #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
- #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
- #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
-
- #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
-
- // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
- //#define FILAMENT_LCD_DISPLAY
-#endif
-
-#endif // CONFIGURATION_H