diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h index ee67417a1..e52eea62a 100644 --- a/Marlin/SanityCheck.h +++ b/Marlin/SanityCheck.h @@ -96,13 +96,13 @@ */ #ifdef MESH_BED_LEVELING #ifdef DELTA - #error MESH_BED_LEVELING does not yet support DELTA printers + #error MESH_BED_LEVELING does not yet support DELTA printers. #endif #ifdef ENABLE_AUTO_BED_LEVELING - #error Select ENABLE_AUTO_BED_LEVELING or MESH_BED_LEVELING, not both + #error Select ENABLE_AUTO_BED_LEVELING or MESH_BED_LEVELING, not both. #endif #if MESH_NUM_X_POINTS > 7 || MESH_NUM_Y_POINTS > 7 - #error MESH_NUM_X_POINTS and MESH_NUM_Y_POINTS need to be less than 8 + #error MESH_NUM_X_POINTS and MESH_NUM_Y_POINTS need to be less than 8. #endif #endif @@ -129,23 +129,23 @@ */ #if defined(Z_PROBE_ENDSTOP) #ifndef Z_PROBE_PIN - #error You must have a Z_PROBE_PIN defined in your pins_XXXX.h file if you enable Z_PROBE_ENDSTOP + #error You must have a Z_PROBE_PIN defined in your pins_XXXX.h file if you enable Z_PROBE_ENDSTOP. #endif #if Z_PROBE_PIN == -1 - #error You must set Z_PROBE_PIN to a valid pin if you enable Z_PROBE_ENDSTOP + #error You must set Z_PROBE_PIN to a valid pin if you enable Z_PROBE_ENDSTOP. #endif // Forcing Servo definitions can break some hall effect sensor setups. Leaving these here for further comment. // #ifndef NUM_SERVOS -// #error You must have NUM_SERVOS defined and there must be at least 1 configured to use Z_PROBE_ENDSTOP +// #error You must have NUM_SERVOS defined and there must be at least 1 configured to use Z_PROBE_ENDSTOP. // #endif // #if defined(NUM_SERVOS) && NUM_SERVOS < 1 -// #error You must have at least 1 servo defined for NUM_SERVOS to use Z_PROBE_ENDSTOP +// #error You must have at least 1 servo defined for NUM_SERVOS to use Z_PROBE_ENDSTOP. // #endif // #ifndef SERVO_ENDSTOPS -// #error You must have SERVO_ENDSTOPS defined and have the Z index set to at least 0 or above to use Z_PROBE_ENDSTOP +// #error You must have SERVO_ENDSTOPS defined and have the Z index set to at least 0 or above to use Z_PROBE_ENDSTOP. // #endif // #ifndef SERVO_ENDSTOP_ANGLES -// #error You must have SERVO_ENDSTOP_ANGLES defined for Z Extend and Retract to use Z_PROBE_AND_ENSTOP +// #error You must have SERVO_ENDSTOP_ANGLES defined for Z Extend and Retract to use Z_PROBE_ENDSTOP. // #endif #endif /** @@ -176,7 +176,7 @@ #define X_PROBE_ERROR #endif #ifdef X_PROBE_ERROR - #error The X axis probing range is too small to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS + #error The X axis probing range is too small to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS. #endif #if Y_PROBE_OFFSET_FROM_EXTRUDER < 0 #if PROBE_SIZE_Y <= -PROBE_AREA_DEPTH @@ -186,7 +186,7 @@ #define Y_PROBE_ERROR #endif #ifdef Y_PROBE_ERROR - #error The Y axis probing range is too small to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS + #error The Y axis probing range is too small to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS. #endif #undef PROBE_SIZE_X @@ -272,18 +272,18 @@ */ #if HAS_AUTO_FAN && HAS_FAN #if EXTRUDER_0_AUTO_FAN_PIN == FAN_PIN - #error You cannot set EXTRUDER_0_AUTO_FAN_PIN equal to FAN_PIN + #error You cannot set EXTRUDER_0_AUTO_FAN_PIN equal to FAN_PIN. #elif EXTRUDER_1_AUTO_FAN_PIN == FAN_PIN - #error You cannot set EXTRUDER_1_AUTO_FAN_PIN equal to FAN_PIN + #error You cannot set EXTRUDER_1_AUTO_FAN_PIN equal to FAN_PIN. #elif EXTRUDER_2_AUTO_FAN_PIN == FAN_PIN - #error You cannot set EXTRUDER_2_AUTO_FAN_PIN equal to FAN_PIN + #error You cannot set EXTRUDER_2_AUTO_FAN_PIN equal to FAN_PIN. #elif EXTRUDER_3_AUTO_FAN_PIN == FAN_PIN - #error You cannot set EXTRUDER_3_AUTO_FAN_PIN equal to FAN_PIN + #error You cannot set EXTRUDER_3_AUTO_FAN_PIN equal to FAN_PIN. #endif #endif #if HAS_FAN && CONTROLLERFAN_PIN == FAN_PIN - #error You cannot set CONTROLLERFAN_PIN equal to FAN_PIN + #error You cannot set CONTROLLERFAN_PIN equal to FAN_PIN. #endif /** @@ -291,38 +291,38 @@ */ #if EXTRUDERS > 3 #if !HAS_HEATER_3 - #error HEATER_3_PIN not defined for this board + #error HEATER_3_PIN not defined for this board. #endif #elif EXTRUDERS > 2 #if !HAS_HEATER_2 - #error HEATER_2_PIN not defined for this board + #error HEATER_2_PIN not defined for this board. #endif #elif EXTRUDERS > 1 || defined(HEATERS_PARALLEL) #if !HAS_HEATER_1 - #error HEATER_1_PIN not defined for this board + #error HEATER_1_PIN not defined for this board. #endif #endif #if !HAS_HEATER_0 - #error HEATER_0_PIN not defined for this board + #error HEATER_0_PIN not defined for this board. #endif /** * Warnings for old configurations */ #ifdef X_HOME_RETRACT_MM - #error [XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM + #error [XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM. #endif #if WATCH_TEMP_PERIOD > 500 - #error WATCH_TEMP_PERIOD now uses seconds instead of milliseconds + #error WATCH_TEMP_PERIOD now uses seconds instead of milliseconds. #endif #if !defined(THERMAL_PROTECTION_HOTENDS) && (defined(WATCH_TEMP_PERIOD) || defined(THERMAL_PROTECTION_PERIOD)) - #error Thermal Runaway Protection for hotends must now be enabled with THERMAL_PROTECTION_HOTENDS + #error Thermal Runaway Protection for hotends must now be enabled with THERMAL_PROTECTION_HOTENDS. #endif #if !defined(THERMAL_PROTECTION_BED) && defined(THERMAL_PROTECTION_BED_PERIOD) - #error Thermal Runaway Protection for the bed must now be enabled with THERMAL_PROTECTION_BED + #error Thermal Runaway Protection for the bed must now be enabled with THERMAL_PROTECTION_BED. #endif #endif //SANITYCHECK_H