Code style and comment tweaks

This commit is contained in:
Scott Lahteine 2020-01-08 20:00:06 -06:00
parent 95046c9047
commit 6e658a7c04
8 changed files with 10 additions and 10 deletions

View file

@ -240,7 +240,7 @@
}
// all the others
static uint32_t spiDelayCyclesX4 = (F_CPU) / 1000000; // 4uS => 125khz
static uint32_t spiDelayCyclesX4 = (F_CPU) / 1000000; // 4µs => 125khz
static uint8_t spiTransferX(uint8_t b) { // using Mode 0
int bits = 8;

View file

@ -1479,7 +1479,7 @@ static void udd_ctrl_in_sent(void)
// The IN data don't must be written in endpoint 0 DPRAM during
// a next setup reception in same endpoint 0 DPRAM.
// Thereby, an OUT ZLP reception must check before IN data write
// and if no OUT ZLP is recevied the data must be written quickly (800us)
// and if no OUT ZLP is received the data must be written quickly (800µs)
// before an eventually ZLP OUT and SETUP reception
flags = cpu_irq_save();
if (Is_udd_out_received(0)) {

View file

@ -177,7 +177,7 @@ int i2s_init() {
*
* fwclk = fbclk / 32
*
* for fwclk = 250kHz (4uS pulse time)
* for fwclk = 250kHz (4µS pulse time)
* N = 10
* M = 20
*/

View file

@ -47,7 +47,7 @@ typedef uint64_t hal_timer_t;
#if ENABLED(I2S_STEPPER_STREAM)
#define STEPPER_TIMER_PRESCALE 1
#define STEPPER_TIMER_RATE 250000 // 250khz, 4us pulses of i2s word clock
#define STEPPER_TIMER_RATE 250000 // 250khz, 4µs pulses of i2s word clock
#define STEPPER_TIMER_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs // wrong would be 0.25
#else
#define STEPPER_TIMER_PRESCALE 40

View file

@ -26,8 +26,8 @@
*
* These are based on the LPC1768 routines.
*
* Couldn't just call exact copies because the overhead resulted in the
* one microsecond delay being about 4uS.
* Couldn't just call exact copies because the overhead
* results in a one microsecond delay taking about 4µS.
*/
#ifdef __cplusplus

View file

@ -618,7 +618,7 @@ void manage_inactivity(const bool ignore_stepper_queue/*=false*/) {
#if PIN_EXISTS(FET_SAFETY)
static millis_t FET_next;
if (ELAPSED(ms, FET_next)) {
FET_next = ms + FET_SAFETY_DELAY; // 2uS pulse every FET_SAFETY_DELAY mS
FET_next = ms + FET_SAFETY_DELAY; // 2µs pulse every FET_SAFETY_DELAY mS
OUT_WRITE(FET_SAFETY_PIN, !FET_SAFETY_INVERTED);
DELAY_US(2);
WRITE(FET_SAFETY_PIN, FET_SAFETY_INVERTED);

View file

@ -2352,7 +2352,7 @@ void MarlinSettings::reset() {
#endif
#if HAS_BED_PROBE
constexpr float dpo[XYZ] = NOZZLE_TO_PROBE_OFFSET;
constexpr float dpo[] = NOZZLE_TO_PROBE_OFFSET;
static_assert(COUNT(dpo) == 3, "NOZZLE_TO_PROBE_OFFSET must contain offsets for X, Y, and Z.");
#if HAS_PROBE_XY_OFFSET
LOOP_XYZ(a) probe_offset[a] = dpo[a];

View file

@ -1492,7 +1492,7 @@ void Stepper::stepper_pulse_phase_isr() {
// Don't step E here - But remember the number of steps to perform
motor_direction(E_AXIS) ? --LA_steps : ++LA_steps;
#else
step_needed[E_AXIS] = delta_error.e >= 0;
step_needed.e = delta_error.e >= 0;
#endif
}
#elif HAS_E0_STEP
@ -1519,7 +1519,7 @@ void Stepper::stepper_pulse_phase_isr() {
#if DISABLED(LIN_ADVANCE)
#if ENABLED(MIXING_EXTRUDER)
if (step_needed[E_AXIS]) E_STEP_WRITE(mixer.get_next_stepper(), !INVERT_E_STEP_PIN);
if (step_needed.e) E_STEP_WRITE(mixer.get_next_stepper(), !INVERT_E_STEP_PIN);
#elif HAS_E0_STEP
PULSE_START(E);
#endif