Also synchronize configurator copies of configs
This commit is contained in:
parent
9d1961ebe3
commit
6eb4f90ce7
4 changed files with 34 additions and 53 deletions
|
@ -411,7 +411,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
// #define MESH_BED_LEVELING // Enable mesh bed leveling
|
||||
|
||||
#ifdef MANUAL_BED_LEVELING
|
||||
#define MBL_Z_STEP 0.025
|
||||
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis
|
||||
#endif // MANUAL_BED_LEVELING
|
||||
|
||||
#ifdef MESH_BED_LEVELING
|
||||
|
@ -605,7 +605,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
|
||||
#ifdef EEPROM_SETTINGS
|
||||
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
#define EEPROM_CHITCHAT // please keep turned on if you can.
|
||||
#define EEPROM_CHITCHAT // Please keep turned on if you can.
|
||||
#endif
|
||||
|
||||
// @section temperature
|
||||
|
@ -646,7 +646,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
||||
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
|
||||
|
||||
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
|
||||
// http://reprap.org/wiki/PanelOne
|
||||
//#define PANEL_ONE
|
||||
|
@ -779,13 +778,13 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
// Uncomment below to enable
|
||||
//#define FILAMENT_SENSOR
|
||||
|
||||
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
|
||||
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
|
||||
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
|
||||
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
|
||||
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
|
||||
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
|
||||
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
|
||||
#define MEASURED_UPPER_LIMIT 3.3 //upper limit factor used for sensor reading validation in mm
|
||||
#define MEASURED_LOWER_LIMIT 1.9 //lower limit factor for sensor reading validation in mm
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
|
||||
//defines used in the code
|
||||
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
|
||||
|
|
|
@ -36,6 +36,15 @@
|
|||
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
#ifdef PIDTEMP
|
||||
// this adds an experimental additional term to the heating power, proportional to the extrusion speed.
|
||||
// if Kc is chosen well, the additional required power due to increased melting should be compensated.
|
||||
#define PID_ADD_EXTRUSION_RATE
|
||||
#ifdef PID_ADD_EXTRUSION_RATE
|
||||
#define DEFAULT_Kc (1) //heating power=Kc*(e_speed)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Automatic Temperature:
|
||||
* The hotend target temperature is calculated by all the buffered lines of gcode.
|
||||
|
@ -46,23 +55,6 @@
|
|||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||
*/
|
||||
#ifdef PIDTEMP
|
||||
// this adds an experimental additional term to the heating power, proportional to the extrusion speed.
|
||||
// if Kc is chosen well, the additional required power due to increased melting should be compensated.
|
||||
#define PID_ADD_EXTRUSION_RATE
|
||||
#ifdef PID_ADD_EXTRUSION_RATE
|
||||
#define DEFAULT_Kc (1) //heating power=Kc*(e_speed)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
||||
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
|
||||
//The maximum buffered steps/sec of the extruder motor are called "se".
|
||||
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
|
||||
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
|
||||
// you exit the value by any M109 without F*
|
||||
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
|
||||
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||
#define AUTOTEMP
|
||||
#ifdef AUTOTEMP
|
||||
#define AUTOTEMP_OLDWEIGHT 0.98
|
||||
|
|
|
@ -14,6 +14,7 @@
|
|||
#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
|
||||
#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
|
||||
#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
|
||||
#define BOARD_RAMPS_13_SF 38 // RAMPS 1.3 / 1.4 (Power outputs: Spindle, Controller Fan)
|
||||
#define BOARD_FELIX2 37 // Felix 2.0+ Electronics Board (RAMPS like)
|
||||
#define BOARD_GEN6 5 // Gen6
|
||||
#define BOARD_GEN6_DELUXE 51 // Gen6 deluxe
|
||||
|
@ -49,8 +50,7 @@
|
|||
#define BOARD_ELEFU_3 21 // Elefu Ra Board (v3)
|
||||
#define BOARD_5DPRINT 88 // 5DPrint D8 Driver Board
|
||||
#define BOARD_LEAPFROG 999 // Leapfrog
|
||||
#define BOARD_WITBOX 41 // bq WITBOX
|
||||
#define BOARD_HEPHESTOS 42 // bq Prusa i3 Hephestos
|
||||
#define BOARD_MKS_BASE 40 // MKS BASE 1.0
|
||||
#define BOARD_BAM_DICE 401 // 2PrintBeta BAM&DICE with STK drivers
|
||||
#define BOARD_BAM_DICE_DUE 402 // 2PrintBeta BAM&DICE Due with STK drivers
|
||||
|
||||
|
|
|
@ -32,8 +32,8 @@
|
|||
// kana_utf Japanese
|
||||
// cn Chinese
|
||||
|
||||
// fallback if no language is set, don't change
|
||||
#ifndef LANGUAGE_INCLUDE
|
||||
// pick your language from the list above
|
||||
#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
#endif
|
||||
|
||||
|
@ -53,26 +53,14 @@
|
|||
#define FIRMWARE_URL "http://3dprint.elettronicain.it/"
|
||||
#elif MB(K8200)
|
||||
#define MACHINE_NAME "K8200"
|
||||
#define FIRMWARE_URL "https://github.com/CONSULitAS/Marlin-K8200"
|
||||
#elif MB(5DPRINT)
|
||||
#define MACHINE_NAME "Makibox"
|
||||
#elif MB(SAV_MKI)
|
||||
#define MACHINE_NAME "SAV MkI"
|
||||
#define FIRMWARE_URL "https://github.com/fmalpartida/Marlin/tree/SAV-MkI-config"
|
||||
#elif MB(WITBOX)
|
||||
#define MACHINE_NAME "WITBOX"
|
||||
#define FIRMWARE_URL "http://www.bq.com/gb/downloads-witbox.html"
|
||||
#elif MB(HEPHESTOS)
|
||||
#define MACHINE_NAME "HEPHESTOS"
|
||||
#define FIRMWARE_URL "http://www.bq.com/gb/downloads-prusa-i3-hephestos.html"
|
||||
#elif MB(BRAINWAVE_PRO)
|
||||
#define MACHINE_NAME "Kossel Pro"
|
||||
#ifndef FIRMWARE_URL
|
||||
#define FIRMWARE_URL "https://github.com/OpenBeamUSA/Marlin/"
|
||||
#endif
|
||||
#else
|
||||
#ifndef MACHINE_NAME
|
||||
#define MACHINE_NAME "3D Printer"
|
||||
#endif
|
||||
#elif !defined(MACHINE_NAME)
|
||||
#define MACHINE_NAME "3D Printer"
|
||||
#endif
|
||||
|
||||
#ifdef CUSTOM_MENDEL_NAME
|
||||
|
@ -122,6 +110,7 @@
|
|||
#define MSG_FREE_MEMORY " Free Memory: "
|
||||
#define MSG_PLANNER_BUFFER_BYTES " PlannerBufferBytes: "
|
||||
#define MSG_OK "ok"
|
||||
#define MSG_WAIT "wait"
|
||||
#define MSG_FILE_SAVED "Done saving file."
|
||||
#define MSG_ERR_LINE_NO "Line Number is not Last Line Number+1, Last Line: "
|
||||
#define MSG_ERR_CHECKSUM_MISMATCH "checksum mismatch, Last Line: "
|
||||
|
@ -221,15 +210,16 @@
|
|||
#define MSG_PID_DEBUG_PTERM " pTerm "
|
||||
#define MSG_PID_DEBUG_ITERM " iTerm "
|
||||
#define MSG_PID_DEBUG_DTERM " dTerm "
|
||||
#define MSG_HEATING_FAILED "Heating failed"
|
||||
#define MSG_EXTRUDER_SWITCHED_OFF "Extruder switched off. Temperature difference between temp sensors is too high !"
|
||||
|
||||
#define MSG_INVALID_EXTRUDER_NUM " - Invalid extruder number !"
|
||||
#define MSG_THERMAL_RUNAWAY_STOP "Thermal Runaway, system stopped! Heater_ID: "
|
||||
#define MSG_SWITCHED_OFF_MAX " switched off. MAXTEMP triggered !!"
|
||||
#define MSG_MINTEMP_EXTRUDER_OFF ": Extruder switched off. MINTEMP triggered !"
|
||||
#define MSG_MAXTEMP_EXTRUDER_OFF ": Extruder" MSG_SWITCHED_OFF_MAX
|
||||
#define MSG_MAXTEMP_BED_OFF "Heated bed" MSG_SWITCHED_OFF_MAX
|
||||
|
||||
#define MSG_HEATER_BED "bed"
|
||||
#define MSG_STOPPED_HEATER ", system stopped! Heater_ID: "
|
||||
#define MSG_REDUNDANCY "Heater switched off. Temperature difference between temp sensors is too high !"
|
||||
#define MSG_T_HEATING_FAILED "Heating failed"
|
||||
#define MSG_T_THERMAL_RUNAWAY "Thermal Runaway"
|
||||
#define MSG_T_MAXTEMP "MAXTEMP triggered"
|
||||
#define MSG_T_MINTEMP "MINTEMP triggered"
|
||||
|
||||
|
||||
// LCD Menu Messages
|
||||
|
||||
|
|
Reference in a new issue