Show Total E during print (#15703)

Marlin/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

Marlin/src/Marlin.cpp

@@ -367,9 +367,14 @@ bool printingIsPaused() {
 }
 
 void startOrResumeJob() {
+  if (!printingIsPaused()) {
     #if ENABLED(CANCEL_OBJECTS)
-    if (!printingIsPaused()) cancelable.reset();
+      cancelable.reset();
     #endif
+    #if ENABLED(LCD_SHOW_E_TOTAL)
+      e_move_accumulator = 0;
+    #endif
+  }
   print_job_timer.start();
 }
 

Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp

@@ -815,14 +815,28 @@ void MarlinUI::draw_status_screen() {
             sprintf_P(mixer_messages, PSTR("%s %d;%d%% "), mix_label, int(mixer.mix[0]), int(mixer.mix[1]));
             lcd_put_u8str(mixer_messages);
 
-          #else
+          #else // !DUAL_MIXING_EXTRUDER
 
+            if (true
+              #if ENABLED(LCD_SHOW_E_TOTAL)
+                && !printingIsActive()
+              #endif
+            ) {
               xy_pos_t lpos = current_position; toLogical(lpos);
               _draw_axis_value(X_AXIS, ftostr4sign(lpos.x), blink);
               lcd_put_wchar(' ');
               _draw_axis_value(Y_AXIS, ftostr4sign(lpos.y), blink);
-
+            }
+            else {
+              #if ENABLED(LCD_SHOW_E_TOTAL)
+                char tmp[20];
+                const uint8_t escale = e_move_accumulator >= 100000.0f ? 10 : 1; // After 100m switch to cm
+                sprintf_P(tmp, PSTR("E %ld%cm       "), uint32_t(_MAX(e_move_accumulator, 0.0f)) / escale, escale == 10 ? 'c' : 'm'); // 1234567mm
+                lcd_put_u8str(tmp);
               #endif
+            }
+
+          #endif // !DUAL_MIXING_EXTRUDER
 
         #endif // HOTENDS <= 2 && (HOTENDS <= 1 || !HAS_HEATED_BED)
 

Marlin/src/lcd/dogm/status_screen_DOGM.cpp

@@ -299,7 +299,7 @@ FORCE_INLINE void _draw_heater_status(const heater_ind_t heater, const bool blin
 //
 FORCE_INLINE void _draw_axis_value(const AxisEnum axis, const char *value, const bool blink) {
   const uint8_t offs = (XYZ_SPACING) * axis;
-  lcd_put_wchar(X_LABEL_POS + offs, XYZ_BASELINE, 'X' + axis);
+  lcd_put_wchar(X_LABEL_POS + offs, XYZ_BASELINE, axis_codes[axis]);
   lcd_moveto(X_VALUE_POS + offs, XYZ_BASELINE);
   if (blink)
     lcd_put_u8str(value);
@@ -328,7 +328,11 @@ void MarlinUI::draw_status_screen() {
     if (first_page) count_renders++;
   #endif
 
-  static char xstring[5], ystring[5], zstring[8];
+  static char xstring[5
+    #if ENABLED(LCD_SHOW_E_TOTAL)
+      + 7
+    #endif
+  ], ystring[5], zstring[8];
   #if ENABLED(FILAMENT_LCD_DISPLAY)
     static char wstring[5], mstring[4];
   #endif
@@ -373,7 +377,19 @@ void MarlinUI::draw_status_screen() {
       heat_bits = new_bits;
     #endif
     const xyz_pos_t lpos = current_position.asLogical();
+    const bool showxy = (true
+      #if ENABLED(LCD_SHOW_E_TOTAL)
+        && !printingIsActive()
+      #endif
+    );
+    if (showxy)
       strcpy(xstring, ftostr4sign(lpos.x));
+    else {
+      #if ENABLED(LCD_SHOW_E_TOTAL)
+        const uint8_t escale = e_move_accumulator >= 100000.0f ? 10 : 1; // After 100m switch to cm
+        sprintf_P(xstring, PSTR("%ld%cm"), uint32_t(_MAX(e_move_accumulator, 0.0f)) / escale, escale == 10 ? 'c' : 'm'); // 1234567mm
+      #endif
+    }
     strcpy(ystring, ftostr4sign(lpos.y));
     strcpy(zstring, ftostr52sp( lpos.z));
     #if ENABLED(FILAMENT_LCD_DISPLAY)
@@ -692,8 +708,14 @@ void MarlinUI::draw_status_screen() {
 
       #else
 
+        if (showxy) {
           _draw_axis_value(X_AXIS, xstring, blink);
           _draw_axis_value(Y_AXIS, ystring, blink);
+        }
+        else {
+          _draw_axis_value(E_AXIS, xstring, true);
+          lcd_put_u8str_P(PSTR("       "));
+        }
 
       #endif
 

Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp

@@ -59,6 +59,10 @@
   #include "../../sd/cardreader.h"
 #endif
 
+#if ENABLED(LCD_SHOW_E_TOTAL)
+  #include "../../Marlin.h" // for printingIsActive
+#endif
+
 #define TEXT_MODE_LCD_WIDTH 16
 
 #define BUFFER_WIDTH   256
@@ -660,7 +664,7 @@ void ST7920_Lite_Status_Screen::draw_status_message() {
   #endif
 }
 
-void ST7920_Lite_Status_Screen::draw_position(const xyz_pos_t &pos, const bool position_known) {
+void ST7920_Lite_Status_Screen::draw_position(const xyze_pos_t &pos, const bool position_known) {
   char str[7];
   set_ddram_address(DDRAM_LINE_4);
   begin_data();
@@ -668,11 +672,25 @@ void ST7920_Lite_Status_Screen::draw_position(const xyz_pos_t &pos, const bool p
   // If position is unknown, flash the labels.
   const unsigned char alt_label = position_known ? 0 : (ui.get_blink() ? ' ' : 0);
 
+  if (true
+    #if ENABLED(LCD_SHOW_E_TOTAL)
+      && !printingIsActive()
+    #endif
+  ) {
     write_byte(alt_label ? alt_label : 'X');
     write_str(dtostrf(pos.x, -4, 0, str), 4);
 
     write_byte(alt_label ? alt_label : 'Y');
     write_str(dtostrf(pos.y, -4, 0, str), 4);
+  }
+  else {
+    #if ENABLED(LCD_SHOW_E_TOTAL)
+      char tmp[15];
+      const uint8_t escale = e_move_accumulator >= 100000.0f ? 10 : 1; // After 100m switch to cm
+      sprintf_P(tmp, PSTR("E%-7ld%cm "), uint32_t(_MAX(e_move_accumulator, 0.0f)) / escale, escale == 10 ? 'c' : 'm'); // 1234567mm
+      write_str(tmp);
+    #endif
+  }
 
   write_byte(alt_label ? alt_label : 'Z');
   write_str(dtostrf(pos.z, -5, 1, str), 5);

Marlin/src/lcd/dogm/status_screen_lite_ST7920.h

@@ -87,7 +87,7 @@ class ST7920_Lite_Status_Screen {
     static void draw_print_time(const duration_t &elapsed);
     static void draw_feedrate_percentage(const uint16_t percentage);
     static void draw_status_message();
-    static void draw_position(const xyz_pos_t &pos, bool position_known = true);
+    static void draw_position(const xyze_pos_t &pos, bool position_known = true);
 
     static bool indicators_changed();
     static bool position_changed();

Marlin/src/module/motion.cpp

@@ -114,6 +114,10 @@ xyze_pos_t destination; // {0}
   uint8_t active_extruder; // = 0
 #endif
 
+#if ENABLED(LCD_SHOW_E_TOTAL)
+  float e_move_accumulator; // = 0
+#endif
+
 // Extruder offsets
 #if HAS_HOTEND_OFFSET
   xyz_pos_t hotend_offset[HOTENDS]; // Initialized by settings.load()

Marlin/src/module/motion.h

@@ -107,6 +107,10 @@ extern int16_t feedrate_percentage;
   constexpr uint8_t active_extruder = 0;
 #endif
 
+#if ENABLED(LCD_SHOW_E_TOTAL)
+  extern float e_move_accumulator;
+#endif
+
 FORCE_INLINE float pgm_read_any(const float *p) { return pgm_read_float(p); }
 FORCE_INLINE signed char pgm_read_any(const signed char *p) { return pgm_read_byte(p); }
 

Marlin/src/module/planner.cpp

@@ -1810,6 +1810,10 @@ bool Planner::_populate_block(block_t * const block, bool split_move,
     delta_mm.e = esteps_float * steps_to_mm[E_AXIS_N(extruder)];
   #endif
 
+  #if ENABLED(LCD_SHOW_E_TOTAL)
+    e_move_accumulator += delta_mm.e;
+  #endif
+
   if (block->steps.a < MIN_STEPS_PER_SEGMENT && block->steps.b < MIN_STEPS_PER_SEGMENT && block->steps.c < MIN_STEPS_PER_SEGMENT) {
     block->millimeters = (0
       #if EXTRUDERS

Marlin/src/module/planner.h

@@ -171,7 +171,7 @@ typedef struct block_t {
 
 } block_t;
 
-#define HAS_POSITION_FLOAT ANY(LIN_ADVANCE, SCARA_FEEDRATE_SCALING, GRADIENT_MIX)
+#define HAS_POSITION_FLOAT ANY(LIN_ADVANCE, SCARA_FEEDRATE_SCALING, GRADIENT_MIX, LCD_SHOW_E_TOTAL)
 
 #define BLOCK_MOD(n) ((n)&(BLOCK_BUFFER_SIZE-1))
 

buildroot/share/tests/megaatmega2560-tests

@@ -31,7 +31,7 @@ opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TE
            EEPROM_SETTINGS SDSUPPORT SD_REPRINT_LAST_SELECTED_FILE BINARY_FILE_TRANSFER \
            BLINKM PCA9632 RGB_LED RGB_LED_R_PIN RGB_LED_G_PIN RGB_LED_B_PIN LED_CONTROL_MENU \
            NEOPIXEL_LED CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CASE_LIGHT_MENU \
-           PID_PARAMS_PER_HOTEND PID_AUTOTUNE_MENU PID_EDIT_MENU \
+           PID_PARAMS_PER_HOTEND PID_AUTOTUNE_MENU PID_EDIT_MENU LCD_SHOW_E_TOTAL \
            NOZZLE_PARK_FEATURE FILAMENT_RUNOUT_SENSOR FILAMENT_RUNOUT_DISTANCE_MM \
            ADVANCED_PAUSE_FEATURE FILAMENT_LOAD_UNLOAD_GCODES FILAMENT_UNLOAD_ALL_EXTRUDERS \
            AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DISTINCT_E_FACTORS \

config/default/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/ADIMLab/Gantry v1/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/ADIMLab/Gantry v2/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Alfawise/U20-bltouch/Configuration_adv.h

@@ -903,6 +903,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Alfawise/U20/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Anet/A2/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Anet/A2plus/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Anet/A6/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Anet/A8/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Anet/A8plus/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Anet/E16/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/ArmEd/Configuration_adv.h

@@ -906,6 +906,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -910,6 +910,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Cartesio/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Creality/CR-10/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Creality/CR-10S/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Creality/CR-10_5S/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Creality/CR-20 Pro/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Creality/CR-20/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Creality/CR-8/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Creality/Ender-3/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Creality/Ender-4/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Creality/Ender-5/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Dagoma/Disco Ultimate/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Einstart-S/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/FYSETC/AIO_II/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/FYSETC/Cheetah/base/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/FYSETC/F6_13/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Felix/DUAL/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Felix/Single/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/FlashForge/CreatorPro/Configuration_adv.h

@@ -901,6 +901,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -906,6 +906,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Geeetech/A10/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Geeetech/A10M/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Geeetech/A20M/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/HMS434/Configuration_adv.h

@@ -870,6 +870,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/JGAurora/A1/Configuration_adv.h

@@ -907,6 +907,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/JGAurora/A5/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/JGAurora/A5S/Configuration_adv.h

@@ -907,6 +907,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/MakerParts/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Malyan/M150/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Malyan/M200/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Mks/Robin/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Mks/Sbase/Configuration_adv.h

@@ -903,6 +903,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/RapideLite/RL200/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/RigidBot/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/SCARA/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Sanguinololu/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Tevo/Michelangelo/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Tevo/Tarantula Pro/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/TheBorg/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/TinyBoy2/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Tronxy/X3A/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Tronxy/X5S-2E/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/UltiMachine/Archim1/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/VORONDesign/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Velleman/K8200/Configuration_adv.h

@@ -915,6 +915,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Velleman/K8400/Dual-head/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Velleman/K8400/Single-head/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/WASP/PowerWASP/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Wanhao/Duplicator 6/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/Anycubic/Kossel/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/Dreammaker/Overlord/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/FLSUN/kossel/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/MKS/SBASE/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/Tevo Little Monster/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/generic/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/kossel_mini/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/delta/kossel_xl/Configuration_adv.h

@@ -904,6 +904,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/makibox/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/tvrrug/Round2/Configuration_adv.h

@@ -902,6 +902,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion

config/examples/wt150/Configuration_adv.h

@@ -903,6 +903,9 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+// Show the E position (filament used) during printing
+//#define LCD_SHOW_E_TOTAL
+
 #if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion