Add NUM_RUNOUT_SENSORS to example configs
This commit is contained in:
parent
d3ca82d8c2
commit
8733d5a296
58 changed files with 348 additions and 290 deletions
|
@ -852,15 +852,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -872,15 +872,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -962,15 +962,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -859,15 +859,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -840,15 +840,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -853,15 +853,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -840,15 +840,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -851,15 +851,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -862,15 +862,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -843,15 +843,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING true // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -847,15 +847,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -834,15 +834,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -834,15 +834,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -858,15 +858,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -867,15 +867,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -859,15 +859,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -858,15 +858,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -856,15 +856,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -864,15 +864,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -872,15 +872,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -876,15 +876,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -851,15 +851,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -856,15 +856,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -856,15 +856,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -850,15 +850,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -864,15 +864,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -855,15 +855,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -883,15 +883,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -908,15 +908,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -843,15 +843,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -863,15 +863,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -843,15 +843,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -882,15 +882,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -853,15 +853,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -852,15 +852,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -982,15 +982,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -973,15 +973,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -982,15 +982,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -969,15 +969,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -972,15 +972,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -972,15 +972,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -981,15 +981,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -866,15 +866,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -855,15 +855,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -853,15 +853,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -847,15 +847,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
|
@ -857,15 +857,16 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout Sensor
|
||||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||||
* Filament Runout Sensors
|
||||
* Mechanical or opto endstops are used to check for the presence of filament.
|
||||
*
|
||||
* RAMPS-based boards use SERVO3_PIN.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||||
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
|
||||
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
|
||||
|
|
Reference in a new issue