Apply const, spacing, etc.

This commit is contained in:
Scott Lahteine 2017-06-27 02:36:19 -05:00
parent c2c8aafda2
commit 941943c167
6 changed files with 43 additions and 42 deletions

View file

@ -189,19 +189,17 @@ void free_memory_pool_report(char * const ptr, const int16_t size) {
* This is useful to check the correctness of the M100 D and the M100 F commands.
*/
void corrupt_free_memory(char *ptr, const uint16_t size) {
if (parser.seen('C')) {
ptr += 8;
const uint16_t near_top = top_of_stack() - ptr - 250, // -250 to avoid interrupt activity that's altered the stack.
j = near_top / (size + 1);
ptr += 8;
const uint16_t near_top = top_of_stack() - ptr - 250, // -250 to avoid interrupt activity that's altered the stack.
j = near_top / (size + 1);
SERIAL_ECHOLNPGM("Corrupting free memory block.\n");
for (uint16_t i = 1; i <= size; i++) {
char * const addr = ptr + i * j;
*addr = i;
SERIAL_ECHOPAIR("\nCorrupting address: ", hex_address(addr));
}
SERIAL_EOL();
SERIAL_ECHOLNPGM("Corrupting free memory block.\n");
for (uint16_t i = 1; i <= size; i++) {
char * const addr = ptr + i * j;
*addr = i;
SERIAL_ECHOPAIR("\nCorrupting address: ", hex_address(addr));
}
SERIAL_EOL();
}
#endif // M100_FREE_MEMORY_CORRUPTOR

View file

@ -1276,16 +1276,17 @@ void get_available_commands() {
*
* Returns TRUE if the target is invalid
*/
bool get_target_extruder_from_command(int code) {
bool get_target_extruder_from_command(const uint16_t code) {
if (parser.seen('T')) {
if (parser.value_byte() >= EXTRUDERS) {
const int8_t e = parser.value_byte();
if (e >= EXTRUDERS) {
SERIAL_ECHO_START();
SERIAL_CHAR('M');
SERIAL_ECHO(code);
SERIAL_ECHOLNPAIR(" " MSG_INVALID_EXTRUDER " ", parser.value_byte());
SERIAL_ECHOLNPAIR(" " MSG_INVALID_EXTRUDER " ", e);
return true;
}
target_extruder = parser.value_byte();
target_extruder = e;
}
else
target_extruder = active_extruder;
@ -5676,7 +5677,7 @@ inline void gcode_G92() {
#if HAS_POSITION_SHIFT
const float p = current_position[i];
#endif
float v = parser.value_axis_units((AxisEnum)i);
const float v = parser.value_axis_units((AxisEnum)i);
current_position[i] = v;
@ -6405,7 +6406,7 @@ static bool pin_is_protected(const int8_t pin) {
inline void gcode_M42() {
if (!parser.seen('S')) return;
int pin_status = parser.value_int();
const int pin_status = parser.value_int();
if (!WITHIN(pin_status, 0, 255)) return;
int pin_number = parser.seen('P') ? parser.value_int() : LED_PIN;
@ -6645,7 +6646,7 @@ inline void gcode_M42() {
*/
inline void gcode_M43() {
if (parser.seen('T')) { // must be first or else it's "S" and "E" parameters will execute endstop or servo test
if (parser.seen('T')) { // must be first or else its "S" and "E" parameters will execute endstop or servo test
toggle_pins();
return;
}
@ -8268,10 +8269,10 @@ inline void gcode_M205() {
home_offset[Z_AXIS] = parser.value_linear_units() - DELTA_HEIGHT;
update_software_endstops(Z_AXIS);
}
if (parser.seen('L')) delta_diagonal_rod = parser.value_linear_units();
if (parser.seen('R')) delta_radius = parser.value_linear_units();
if (parser.seen('S')) delta_segments_per_second = parser.value_float();
if (parser.seen('B')) delta_calibration_radius = parser.value_float();
if (parser.seen('L')) delta_diagonal_rod = parser.value_linear_units();
if (parser.seen('R')) delta_radius = parser.value_linear_units();
if (parser.seen('S')) delta_segments_per_second = parser.value_float();
if (parser.seen('B')) delta_calibration_radius = parser.value_float();
if (parser.seen('X')) delta_tower_angle_trim[A_AXIS] = parser.value_float();
if (parser.seen('Y')) delta_tower_angle_trim[B_AXIS] = parser.value_float();
if (parser.seen('Z')) { // rotate all 3 axis for Z = 0
@ -8580,7 +8581,7 @@ inline void gcode_M226() {
*/
inline void gcode_M280() {
if (!parser.seen('P')) return;
int servo_index = parser.value_int();
const int servo_index = parser.value_int();
if (WITHIN(servo_index, 0, NUM_SERVOS - 1)) {
if (parser.seen('S'))
MOVE_SERVO(servo_index, parser.value_int());
@ -8753,7 +8754,7 @@ inline void gcode_M226() {
* M302 S170 P1 ; set min extrude temp to 170 but leave disabled
*/
inline void gcode_M302() {
bool seen_S = parser.seen('S');
const bool seen_S = parser.seen('S');
if (seen_S) {
thermalManager.extrude_min_temp = parser.value_celsius();
thermalManager.allow_cold_extrude = (thermalManager.extrude_min_temp == 0);
@ -8960,10 +8961,12 @@ inline void gcode_M400() { stepper.synchronize(); }
* M405: Turn on filament sensor for control
*/
inline void gcode_M405() {
// This is technically a linear measurement, but since it's quantized to centimeters and is a different unit than
// everything else, it uses parser.value_int() instead of parser.value_linear_units().
if (parser.seen('D')) meas_delay_cm = parser.value_byte();
NOMORE(meas_delay_cm, MAX_MEASUREMENT_DELAY);
// This is technically a linear measurement, but since it's quantized to centimeters and is a different
// unit than everything else, it uses parser.value_byte() instead of parser.value_linear_units().
if (parser.seen('D')) {
meas_delay_cm = parser.value_byte();
NOMORE(meas_delay_cm, MAX_MEASUREMENT_DELAY);
}
if (filwidth_delay_index[1] == -1) { // Initialize the ring buffer if not done since startup
const uint8_t temp_ratio = thermalManager.widthFil_to_size_ratio() - 100; // -100 to scale within a signed byte

View file

@ -523,7 +523,7 @@ struct directoryEntry {
uint8_t reservedNT;
/**
* The granularity of the seconds part of creationTime is 2 seconds
* so this field is a count of tenths of a second and its valid
* so this field is a count of tenths of a second and it's valid
* value range is 0-199 inclusive. (WHG note - seems to be hundredths)
*/
uint8_t creationTimeTenths;

View file

@ -2,7 +2,7 @@
http://www.k8400.eu/
Configuration files for the K8400, ported upstream from the official Velleman firmware.
Like it's predecessor, (K8200), the K8400 is a 3Drag clone. There are some minor differences, documented in pins_K8400.h.
Like its predecessor, (K8200), the K8400 is a 3Drag clone. There are some minor differences, documented in pins_K8400.h.
Single and dual head configurations provided. Copy the correct Configuration.h and Configuration_adv.h to the /Marlin/ directory.

View file

@ -95,7 +95,7 @@ static inline void handle_interrupts(timer16_Sequence_t timer, volatile uint16_t
if (SERVO_INDEX(timer, Channel[timer]) < ServoCount && Channel[timer] < SERVOS_PER_TIMER) {
*OCRnA = *TCNTn + SERVO(timer, Channel[timer]).ticks;
if (SERVO(timer, Channel[timer]).Pin.isActive) // check if activated
digitalWrite(SERVO(timer, Channel[timer]).Pin.nbr, HIGH); // its an active channel so pulse it high
digitalWrite(SERVO(timer, Channel[timer]).Pin.nbr, HIGH); // it's an active channel so pulse it high
}
else {
// finished all channels so wait for the refresh period to expire before starting over

View file

@ -38,18 +38,18 @@ typedef void (*twiRequestFunc_t)();
/**
* TWIBUS class
*
* This class implements a wrapper around the two wire (I2C) bus, it allows
* Marlin to send and request data from any slave device on the bus. This is
* an experimental feature and it's inner workings as well as public facing
* interface are prune to change in the future.
* This class implements a wrapper around the two wire (I2C) bus, allowing
* Marlin to send and request data from any slave device on the bus.
*
* The two main consumers of this class are M260 and M261, where M260 allows
* Marlin to send a I2C packet to a device (please be aware that no repeated
* starts are possible), this can be done in caching method by calling multiple
* times M260 B<byte-1 value in base 10> or a one liner M260, have a look at
* the gcode_M260() function for more information. M261 allows Marlin to
* request data from a device, the received data is then relayed into the serial
* line for host interpretation.
* The two main consumers of this class are M260 and M261. M260 provides a way
* to send an I2C packet to a device (no repeated starts) by caching up to 32
* bytes in a buffer and then sending the buffer.
* M261 requests data from a device. The received data is relayed to serial out
* for the host to interpret.
*
* For more information see
* - http://marlinfw.org/docs/gcode/M260.html
* - http://marlinfw.org/docs/gcode/M261.html
*
*/
class TWIBus {