Rename BEEPER to BEEPER_PIN

For consistency with other pins, allowing use of `PIN_EXISTS` macro.
This commit is contained in:
Scott Lahteine 2015-07-30 23:19:11 -07:00 committed by Richard Wackerbarth
parent b217474eab
commit 94a796c8cc
24 changed files with 58 additions and 58 deletions

View file

@ -512,7 +512,7 @@
#define WRITE_FAN(v) WRITE(FAN_PIN, v)
#endif
#define HAS_BUZZER ((defined(BEEPER) && BEEPER >= 0) || defined(LCD_USE_I2C_BUZZER))
#define HAS_BUZZER (PIN_EXISTS(BEEPER) || defined(LCD_USE_I2C_BUZZER))
#if defined(NUM_SERVOS) && NUM_SERVOS > 0
#ifndef X_ENDSTOP_SERVO_NR

View file

@ -7,22 +7,22 @@
if (freq > 0) {
#if ENABLED(LCD_USE_I2C_BUZZER)
lcd_buzz(duration, freq);
#elif defined(BEEPER) && BEEPER >= 0 // on-board buzzers have no further condition
SET_OUTPUT(BEEPER);
#elif PIN_EXISTS(BEEPER) // on-board buzzers have no further condition
SET_OUTPUT(BEEPER_PIN);
#ifdef SPEAKER // a speaker needs a AC ore a pulsed DC
//tone(BEEPER, freq, duration); // needs a PWMable pin
//tone(BEEPER_PIN, freq, duration); // needs a PWMable pin
unsigned int delay = 1000000 / freq / 2;
int i = duration * freq / 1000;
while (i--) {
WRITE(BEEPER,HIGH);
WRITE(BEEPER_PIN, HIGH);
delayMicroseconds(delay);
WRITE(BEEPER,LOW);
WRITE(BEEPER_PIN, LOW);
delayMicroseconds(delay);
}
#else // buzzer has its own resonator - needs a DC
WRITE(BEEPER, HIGH);
WRITE(BEEPER_PIN, HIGH);
delay(duration);
WRITE(BEEPER, LOW);
WRITE(BEEPER_PIN, LOW);
#endif
#else
delay(duration);

View file

@ -30,8 +30,8 @@
#define HEATER_BED_PIN 9 // BED
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
#undef BEEPER
#define BEEPER -1
#undef BEEPER_PIN
#define BEEPER_PIN -1
#undef LCD_PINS_RS
#undef LCD_PINS_ENABLE
@ -56,6 +56,6 @@
#else
#define BEEPER 33
#define BEEPER_PIN 33
#endif // ULTRA_LCD && NEWPANEL

View file

@ -8,7 +8,8 @@
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER 33
#define BEEPER_PIN 33
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 31
#define DOGLCD_CS 32

View file

@ -6,7 +6,7 @@
#undef FAN_PIN
#define FAN_PIN 6 //Part Cooling System
#define BEEPER 33
#define BEEPER_PIN 33
#define CONTROLLERFAN_PIN 4 //Pin used for the fan to cool motherboard (-1 to disable)
//Fans/Water Pump to cool the hotend cool side.
#define EXTRUDER_0_AUTO_FAN_PIN 5
@ -97,7 +97,7 @@
//LCD Pins//
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER 33
#define BEEPER_PIN 33
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 45

View file

@ -53,7 +53,7 @@
#define TEMP_2_PIN 1 //ANALOG NUMBERING
#define TEMP_BED_PIN 0 //ANALOG NUMBERING
#define BEEPER 36
#define BEEPER_PIN 36
#define KILL_PIN -1

View file

@ -56,7 +56,7 @@
//#define TX_ENABLE_PIN 12
//#define RX_ENABLE_PIN 13
#define BEEPER -1
#define BEEPER_PIN -1
#define SDCARDDETECT -1
#define SUICIDE_PIN -1 //has to be defined; otherwise Power_off doesn't work

View file

@ -89,7 +89,7 @@
#endif
#ifdef MINIPANEL
#define BEEPER 46
#define BEEPER_PIN 46
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 47
#define DOGLCD_CS 45

View file

@ -58,7 +58,7 @@
#define HEATER_BED_PIN 10 // BED
#define TEMP_BED_PIN 14 // ANALOG NUMBERING
#define BEEPER 33 // AUX-4
#define BEEPER_PIN 33 // AUX-4
#if defined(ULTRA_LCD) && defined(NEWPANEL)

View file

@ -74,7 +74,7 @@
#define TEMP_BED_PIN 14 // ANALOG NUMBERING
#endif
#define BEEPER 64
#define BEEPER_PIN 64
#define LCD_PINS_RS 14

View file

@ -76,7 +76,7 @@
#define TEMP_2_PIN (TEMP_SENSOR_2 == -1 ? 9 : 12) // ANALOG NUMBERING
#define TEMP_BED_PIN (TEMP_SENSOR_BED == -1 ? 8 : 14) // ANALOG NUMBERING
#define BEEPER 61
#define BEEPER_PIN 61
#define LCD_PINS_RS 32
#define LCD_PINS_ENABLE 31

View file

@ -91,8 +91,8 @@
#if ENABLED(ULTRA_LCD)
#define KILL_PIN 32
#if ENABLED(NEWPANEL)
//arduino pin which triggers an piezzo beeper
#define BEEPER 84 // Beeper on AUX-4
#define BEEPER_PIN 84 // Beeper on AUX-4
#define LCD_PINS_RS 82
#define LCD_PINS_ENABLE 18
#define LCD_PINS_D4 19

View file

@ -59,8 +59,7 @@
#define HEATER_BED_PIN 3 // BED
#define TEMP_BED_PIN 6 // ANALOG NUMBERING
#define BEEPER -1
#define BEEPER_PIN -1
#define LCD_PINS_RS -1
#define LCD_PINS_ENABLE -1

View file

@ -79,7 +79,7 @@
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
//we have no buzzer installed
#define BEEPER -1
#define BEEPER_PIN -1
//LCD Pins
#if ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 27 //RX1 - fastio.h pin mapping 27
@ -92,7 +92,7 @@
#endif // ULTRA_LCD && NEWPANEL
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER 32 //FastIO
#define BEEPER_PIN 32 //FastIO
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 42 //Non-FastIO
#define DOGLCD_CS 43 //Non-FastIO

View file

@ -112,8 +112,9 @@
#if ENABLED(ULTRA_LCD)
#define KILL_PIN 80
#if ENABLED(NEWPANEL)
//arduino pin which triggers an piezzo beeper
#define BEEPER 79 // Beeper on AUX-4
#define BEEPER_PIN 79 // Beeper on AUX-4
#define LCD_PINS_RS 70
#define LCD_PINS_ENABLE 71
#define LCD_PINS_D4 72
@ -133,8 +134,9 @@
#define SDCARDDETECT 81 // Ramps does not use this port
#else //!NEWPANEL - old style panel with shift register
//arduino pin witch triggers an piezzo beeper
#define BEEPER 33 No Beeper added
#define BEEPER_PIN 33 // No Beeper added
//buttons are attached to a shift register
// Not wired this yet
// #define SHIFT_CLK 38
@ -165,7 +167,7 @@
#endif // ULTRA_LCD
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define BEEPER 44
#define BEEPER_PIN 44
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 70
#define DOGLCD_CS 71

View file

@ -159,7 +159,7 @@
#endif
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
#define BEEPER 37
#define BEEPER_PIN 37
#define BTN_EN1 31
#define BTN_EN2 33
@ -186,12 +186,12 @@
#define SDCARDDETECT 49
#define LCD_SDSS 53
#define KILL_PIN 41
#define BEEPER 23
#define BEEPER_PIN 23
#define DOGLCD_CS 29
#define DOGLCD_A0 27
#define LCD_PIN_BL 33
#elif defined(MINIPANEL)
#define BEEPER 42
#define BEEPER_PIN 42
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 66
@ -211,9 +211,10 @@
#define BTN_ENC 59 //the click switch
//not connected to a pin
#define SDCARDDETECT 49
#else
// arduino pin which triggers an piezzo beeper
#define BEEPER 33 // Beeper on AUX-4
#define BEEPER_PIN 33 // Beeper on AUX-4
// buttons are directly attached using AUX-2
#if ENABLED(REPRAPWORLD_KEYPAD)
@ -241,8 +242,8 @@
#endif
#else // !NEWPANEL (Old-style panel with shift register)
// Arduino pin to trigger a piezzo beeper
#define BEEPER 33 // No Beeper added
#define BEEPER_PIN 33 // No Beeper added
// Buttons are attached to a shift register
// Not wired yet

View file

@ -22,8 +22,8 @@
#if ENABLED(RIGIDBOT_PANEL)
#undef BEEPER
#define BEEPER -1
#undef BEEPER_PIN
#define BEEPER_PIN -1
#undef SDCARDDETECT
#define SDCARDDETECT 22
@ -48,8 +48,8 @@
#elif defined(REPRAP_DISCOUNT_SMART_CONTROLLER)
#undef BEEPER
#define BEEPER -1
#undef BEEPER_PIN
#define BEEPER_PIN -1
#undef SDCARDDETECT
#define SDCARDDETECT 22

View file

@ -102,7 +102,7 @@
#define SDPOWER -1
#define SDSS 53
#define SDCARDDETECT 49
#define BEEPER 44
#define BEEPER_PIN 44
#define LCD_PINS_RS 19
#define LCD_PINS_ENABLE 42
#define LCD_PINS_D4 18

View file

@ -95,7 +95,7 @@
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
// No buzzer installed
#define BEEPER -1
#define BEEPER_PIN -1
// LCD Pins
#if ENABLED(DOGLCD)
@ -106,7 +106,7 @@
#define LCD_PINS_RS 30 //CS chip select /SS chip slave select
#define LCD_PINS_ENABLE 29 //SID (MOSI)
#define LCD_PINS_D4 17 //SCK (CLK) clock
#define BEEPER 27 // Pin 27 is take by LED_Pin, but Melzi LED do nothing with Marlin and I take this pin for BEEPER.... See here > [github.com] , If you want use this pin with Gcode M42 instead BEEPER
#define BEEPER_PIN 27 // Pin 27 is taken by LED_PIN, but Melzi LED does nothing with Marlin so this can be used for BEEPER_PIN. You can use this pin with M42 instead of BEEPER_PIN.
#else // Sanguinololu 1.3
#define LCD_PINS_RS 4
#define LCD_PINS_ENABLE 17
@ -160,7 +160,7 @@
#elif ENABLED(MAKRPANEL)
#define BEEPER 29
#define BEEPER_PIN 29
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 30

View file

@ -85,7 +85,7 @@
#define ALARM_PIN -1
#define SDCARDDETECT -1
#define BEEPER -1
#define BEEPER_PIN -1
#define LCD_PINS_RS -1
#define LCD_PINS_ENABLE -1
#define LCD_PINS_D4 -1

View file

@ -68,9 +68,10 @@
#endif
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
//we have no buzzer installed
#define BEEPER -1
//LCD Pins
#define BEEPER_PIN -1
#if ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 27 //RX1 - fastio.h pin mapping 27
#define BTN_EN2 26 //TX1 - fastio.h pin mapping 26

View file

@ -58,8 +58,7 @@
#define MOTOR_CURRENT_PWM_RANGE 2000
#define DEFAULT_PWM_MOTOR_CURRENT {1300, 1300, 1250}
//arduino pin witch triggers an piezzo beeper
#define BEEPER 18
#define BEEPER_PIN 18
#define LCD_PINS_RS 20
#define LCD_PINS_ENABLE 15

View file

@ -57,9 +57,9 @@
#if ENABLED(ULTRA_LCD)
#define BEEPER_PIN 18
#if ENABLED(NEWPANEL)
//arduino pin witch triggers an piezzo beeper
#define BEEPER 18
#define LCD_PINS_RS 20
#define LCD_PINS_ENABLE 17
@ -71,15 +71,12 @@
//buttons are directly attached
#define BTN_EN1 40
#define BTN_EN2 42
#define BTN_ENC 19 //the click
#define BTN_ENC 19
#define SDCARDDETECT 38
#else //!NEWPANEL - Old style panel with shift register
//arduino pin witch triggers an piezzo beeper
#define BEEPER 18
//buttons are attached to a shift register
#define SHIFT_CLK 38
#define SHIFT_LD 42

View file

@ -1325,7 +1325,7 @@ void lcd_quick_feedback() {
#define LCD_FEEDBACK_FREQUENCY_DURATION_MS (1000/6)
#endif
lcd.buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ);
#elif defined(BEEPER) && BEEPER >= 0
#elif PIN_EXISTS(BEEPER)
#ifndef LCD_FEEDBACK_FREQUENCY_HZ
#define LCD_FEEDBACK_FREQUENCY_HZ 5000
#endif