Clean up some temp config

This commit is contained in:
Scott Lahteine 2019-03-11 16:24:58 -05:00
parent 785a7028bf
commit 98b55421a5
95 changed files with 1804 additions and 2089 deletions

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 5 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 5 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 5 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 5 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 250 #define HEATER_0_MAXTEMP 250
#define HEATER_1_MAXTEMP 250 #define HEATER_1_MAXTEMP 250
#define HEATER_2_MAXTEMP 250 #define HEATER_2_MAXTEMP 250
#define HEATER_3_MAXTEMP 250 #define HEATER_3_MAXTEMP 250
#define HEATER_4_MAXTEMP 250 #define HEATER_4_MAXTEMP 250
#define HEATER_5_MAXTEMP 250 #define HEATER_5_MAXTEMP 250
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 130 #define BED_MAXTEMP 130
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 130 #define BED_MAXTEMP 130
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -389,37 +389,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 6 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 6 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 6 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 6 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 130 #define BED_MAXTEMP 130
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 285 #define HEATER_0_MAXTEMP 285
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 115 #define BED_MAXTEMP 115
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 115 #define BED_MAXTEMP 115
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 260 #define HEATER_0_MAXTEMP 260
#define HEATER_1_MAXTEMP 260 #define HEATER_1_MAXTEMP 260
#define HEATER_2_MAXTEMP 260 #define HEATER_2_MAXTEMP 260
#define HEATER_3_MAXTEMP 260 #define HEATER_3_MAXTEMP 260
#define HEATER_4_MAXTEMP 260 #define HEATER_4_MAXTEMP 260
#define HEATER_5_MAXTEMP 260 #define HEATER_5_MAXTEMP 260
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -396,30 +396,27 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 230 #define HEATER_0_MAXTEMP 230
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 260 #define HEATER_0_MAXTEMP 260
#define HEATER_1_MAXTEMP 260 #define HEATER_1_MAXTEMP 260
#define HEATER_2_MAXTEMP 260 #define HEATER_2_MAXTEMP 260
#define HEATER_3_MAXTEMP 260 #define HEATER_3_MAXTEMP 260
#define HEATER_4_MAXTEMP 260 #define HEATER_4_MAXTEMP 260
#define HEATER_5_MAXTEMP 260 #define HEATER_5_MAXTEMP 260
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -389,37 +389,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 4 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 4 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 1 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 1 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 415 #define HEATER_0_MAXTEMP 415
#define HEATER_1_MAXTEMP 415 #define HEATER_1_MAXTEMP 415
#define HEATER_2_MAXTEMP 415 #define HEATER_2_MAXTEMP 415
#define HEATER_3_MAXTEMP 415 #define HEATER_3_MAXTEMP 415
#define HEATER_4_MAXTEMP 415 #define HEATER_4_MAXTEMP 415
#define HEATER_5_MAXTEMP 415 #define HEATER_5_MAXTEMP 415
#define BED_MAXTEMP 165 #define BED_MAXTEMP 165
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120 #define BED_MAXTEMP 120
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 250 #define HEATER_0_MAXTEMP 250
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120 #define BED_MAXTEMP 120
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 265 #define HEATER_0_MAXTEMP 265
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120 #define BED_MAXTEMP 120
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -397,37 +397,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120 #define BED_MAXTEMP 120
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 75 #define BED_MAXTEMP 75
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125 #define BED_MAXTEMP 125
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -390,37 +390,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 15 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 15 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 15 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 15 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 245 #define HEATER_0_MAXTEMP 245
#define HEATER_1_MAXTEMP 245 #define HEATER_1_MAXTEMP 245
#define HEATER_2_MAXTEMP 245 #define HEATER_2_MAXTEMP 245
#define HEATER_3_MAXTEMP 245 #define HEATER_3_MAXTEMP 245
#define HEATER_4_MAXTEMP 245 #define HEATER_4_MAXTEMP 245
#define HEATER_5_MAXTEMP 245 #define HEATER_5_MAXTEMP 245
#define BED_MAXTEMP 115 #define BED_MAXTEMP 115
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -433,38 +433,35 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 290 #define HEATER_0_MAXTEMP 290
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#if ENABLED(BED_AC) #if ENABLED(BED_AC)
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
#else #else
#define BED_MAXTEMP 100 #define BED_MAXTEMP 100
#endif #endif
//=========================================================================== //===========================================================================

View file

@ -403,37 +403,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 410 #define HEATER_0_MAXTEMP 410
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -397,37 +397,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 410 #define HEATER_0_MAXTEMP 410
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125 #define BED_MAXTEMP 125
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125 #define BED_MAXTEMP 125
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125 #define BED_MAXTEMP 125
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -393,37 +393,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 265 #define HEATER_0_MAXTEMP 265
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120 #define BED_MAXTEMP 120
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -408,37 +408,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -396,37 +396,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 250 #define HEATER_0_MAXTEMP 250
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 100 #define BED_MAXTEMP 100
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -389,37 +389,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -389,37 +389,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 250 #define HEATER_0_MAXTEMP 250
#define HEATER_1_MAXTEMP 250 #define HEATER_1_MAXTEMP 250
#define HEATER_2_MAXTEMP 250 #define HEATER_2_MAXTEMP 250
#define HEATER_3_MAXTEMP 250 #define HEATER_3_MAXTEMP 250
#define HEATER_4_MAXTEMP 250 #define HEATER_4_MAXTEMP 250
#define HEATER_5_MAXTEMP 250 #define HEATER_5_MAXTEMP 250
#define BED_MAXTEMP 120 #define BED_MAXTEMP 120
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -391,37 +391,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
//#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 //#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -419,37 +419,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 3 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 3 // (seconds) #define TEMP_HYSTERESIS 2 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_HYSTERESIS 2 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -389,37 +389,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -415,37 +415,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 250 #define HEATER_0_MAXTEMP 250
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 100 #define BED_MAXTEMP 100
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 260 #define HEATER_0_MAXTEMP 260
#define HEATER_1_MAXTEMP 260 #define HEATER_1_MAXTEMP 260
#define HEATER_2_MAXTEMP 260 #define HEATER_2_MAXTEMP 260
#define HEATER_3_MAXTEMP 260 #define HEATER_3_MAXTEMP 260
#define HEATER_4_MAXTEMP 260 #define HEATER_4_MAXTEMP 260
#define HEATER_5_MAXTEMP 260 #define HEATER_5_MAXTEMP 260
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 130 #define BED_MAXTEMP 130
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -390,30 +390,27 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
// Tronxy X5S-2E: // Tronxy X5S-2E:
// WARNING: Never exceed 260C. The OEM stock model uses low temperature heat breaks with PTFE-lining. // WARNING: Never exceed 260C. The OEM stock model uses low temperature heat breaks with PTFE-lining.
#define HEATER_0_MAXTEMP 260 #define HEATER_0_MAXTEMP 260
@ -424,7 +421,7 @@
#define HEATER_5_MAXTEMP 260 #define HEATER_5_MAXTEMP 260
// Tronxy X5S-2E: // Tronxy X5S-2E:
// The OEM stock model uses a clone MK3a 300 @ 12V with no insulation and can reach a maximum 70C at 25C ambient. // The OEM stock model uses a clone MK3a 300 @ 12V with no insulation and can reach a maximum 70C at 25C ambient.
#define BED_MAXTEMP 81 #define BED_MAXTEMP 81
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -408,37 +408,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 2 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 2 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 5 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 5 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 2 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 2 // (seconds) #define TEMP_HYSTERESIS 5 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_HYSTERESIS 5 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -407,37 +407,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 5 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 5 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 230 #define HEATER_0_MAXTEMP 230
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 260 #define HEATER_0_MAXTEMP 260
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120 #define BED_MAXTEMP 120
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -409,37 +409,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120 #define BED_MAXTEMP 120
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 1 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 1 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 250 #define HEATER_0_MAXTEMP 250
#define HEATER_1_MAXTEMP 250 #define HEATER_1_MAXTEMP 250
#define HEATER_2_MAXTEMP 250 #define HEATER_2_MAXTEMP 250
#define HEATER_3_MAXTEMP 250 #define HEATER_3_MAXTEMP 250
#define HEATER_4_MAXTEMP 250 #define HEATER_4_MAXTEMP 250
#define HEATER_5_MAXTEMP 250 #define HEATER_5_MAXTEMP 250
#define BED_MAXTEMP 115 #define BED_MAXTEMP 115
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 1 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 1 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 250 #define HEATER_0_MAXTEMP 250
#define HEATER_1_MAXTEMP 250 #define HEATER_1_MAXTEMP 250
#define HEATER_2_MAXTEMP 250 #define HEATER_2_MAXTEMP 250
#define HEATER_3_MAXTEMP 250 #define HEATER_3_MAXTEMP 250
#define HEATER_4_MAXTEMP 250 #define HEATER_4_MAXTEMP 250
#define HEATER_5_MAXTEMP 250 #define HEATER_5_MAXTEMP 250
#define BED_MAXTEMP 115 #define BED_MAXTEMP 115
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 1 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 1 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -393,37 +393,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 1 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 1 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -392,37 +392,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -396,37 +396,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 16 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 16 // (seconds) #define TEMP_WINDOW 5 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 12 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 12 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 5 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 245 #define HEATER_0_MAXTEMP 245
#define HEATER_1_MAXTEMP 245 #define HEATER_1_MAXTEMP 245
#define HEATER_2_MAXTEMP 245 #define HEATER_2_MAXTEMP 245
#define HEATER_3_MAXTEMP 245 #define HEATER_3_MAXTEMP 245
#define HEATER_4_MAXTEMP 245 #define HEATER_4_MAXTEMP 245
#define HEATER_5_MAXTEMP 245 #define HEATER_5_MAXTEMP 245
#define BED_MAXTEMP 115 #define BED_MAXTEMP 115
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -389,37 +389,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================

View file

@ -388,37 +388,34 @@
//#define TEMP_SENSOR_1_AS_REDUNDANT //#define TEMP_SENSOR_1_AS_REDUNDANT
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
// Extruder temperature must be close to target for this long before M109 returns success #define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_RESIDENCY_TIME 10 // (seconds) #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// Bed temperature must be close to target for this long before M190 returns success #define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // Below this temperature the heater will be switched off
// to check that the wiring to the thermistor is not broken. // because it probably indicates a broken thermistor wire.
// Otherwise this would lead to the heater being powered on all the time. #define HEATER_0_MINTEMP 5
#define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5
#define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5
#define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5
#define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5
#define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5
#define HEATER_5_MINTEMP 5 #define BED_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // Above this temperature the heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This can protect components from overheating, but NOT from shorts and failures.
// You should use MINTEMP for thermistor short/failure protection. // (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 #define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275 #define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275 #define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//=========================================================================== //===========================================================================
//============================= PID Settings ================================ //============================= PID Settings ================================