From 9fbd73d9311cc33520ad12130f1ca8ee6054a9a9 Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Wed, 5 Dec 2018 18:42:16 -0600 Subject: [PATCH] Fix up some delta settings --- .../delta/Anycubic/Kossel/Configuration.h | 30 +++++++++---------- .../FLSUN/auto_calibrate/Configuration.h | 18 +++++------ .../delta/FLSUN/kossel/Configuration.h | 20 ++++++------- .../delta/FLSUN/kossel_mini/Configuration.h | 18 +++++------ .../Geeetech/Rostock 301/Configuration.h | 18 +++++------ .../delta/Hatchbox_Alpha/Configuration.h | 18 +++++------ .../examples/delta/MKS/SBASE/Configuration.h | 18 +++++------ .../delta/Tevo Little Monster/Configuration.h | 20 ++++++------- .../examples/delta/generic/Configuration.h | 18 +++++------ .../delta/kossel_mini/Configuration.h | 18 +++++------ .../examples/delta/kossel_pro/Configuration.h | 18 +++++------ .../examples/delta/kossel_xl/Configuration.h | 18 +++++------ buildroot/share/fonts/README.md | 2 +- 13 files changed, 117 insertions(+), 117 deletions(-) diff --git a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h index 5a577ddcd..9d35494d9 100644 --- a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -595,42 +595,42 @@ // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes #define DELTA_CALIBRATION_RADIUS DELTA_PRINTABLE_RADIUS - MIN_PROBE_EDGE // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif #if ENABLED(ANYCUBIC_KOSSEL_PLUS) // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 116.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 116.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 267 // (mm) + #define DELTA_DIAGONAL_ROD 267 // (mm) // Horizontal offset from middle of printer to smooth rod center. - #define DELTA_SMOOTH_ROD_OFFSET 186 // (mm) + #define DELTA_SMOOTH_ROD_OFFSET 186 // (mm) // Horizontal offset of the universal joints on the end effector. - #define DELTA_EFFECTOR_OFFSET 31 // (mm) + #define DELTA_EFFECTOR_OFFSET 31 // (mm) // Horizontal offset of the universal joints on the carriages. - #define DELTA_CARRIAGE_OFFSET 20.6 // (mm) + #define DELTA_CARRIAGE_OFFSET 20.6 // (mm) // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET)) //mm Get this value from auto calibrate + #define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET)) // (mm) Get this value from G33 auto calibrate #else // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 90.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 90.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 218.0 // (mm) + #define DELTA_DIAGONAL_ROD 218.0 // (mm) // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 97.0 //mm Get this value from auto calibrate + #define DELTA_RADIUS 97.0 // (mm) Get this value from G33 auto calibrate #endif - // height from z=0 to home position - #define DELTA_HEIGHT 320.00 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 320.00 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index f7ae89e47..b70ba4299 100644 --- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -562,29 +562,29 @@ // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes #define DELTA_CALIBRATION_RADIUS 73.5 // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 85.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 85.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 218.0 // (mm) + #define DELTA_DIAGONAL_ROD 218.0 // (mm) - // height from z=0 to home position - #define DELTA_HEIGHT 295.00 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 295.00 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 101.0 //mm Get this value from auto calibrate + #define DELTA_RADIUS 101.0 // (mm) Get this value from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h index d29c31148..db4e219a7 100644 --- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h @@ -560,31 +560,31 @@ #if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU) // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes - #define DELTA_CALIBRATION_RADIUS 63 // (mm) + #define DELTA_CALIBRATION_RADIUS 63 // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 70.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 70.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 218.0 // (mm) + #define DELTA_DIAGONAL_ROD 218.0 // (mm) - // height from z=0 to home position - #define DELTA_HEIGHT 317.94 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 317.94 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 110.0 //mm Get this value from auto calibrate + #define DELTA_RADIUS 110.0 // (mm) Get this value from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h index 6801592a3..c136c7d98 100644 --- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -562,29 +562,29 @@ // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes #define DELTA_CALIBRATION_RADIUS 73.5 // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 85.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 85.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 218.0 // (mm) + #define DELTA_DIAGONAL_ROD 218.0 // (mm) - // height from z=0 to home position - #define DELTA_HEIGHT 280.00 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 280.00 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 101.0 //mm Get this value from auto calibrate + #define DELTA_RADIUS 101.0 // (mm) Get this value from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h index 42d6e991c..ec108165f 100644 --- a/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -563,29 +563,29 @@ // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes #define DELTA_CALIBRATION_RADIUS 121.5 // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 90.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 90.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 196.0 // (mm) + #define DELTA_DIAGONAL_ROD 196.0 // (mm) - // height from z=0 to home position - #define DELTA_HEIGHT 228.00 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 228.00 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 92 //124.0 //mm Get this value from auto calibrate + #define DELTA_RADIUS 92 //124.0 // (mm) Get this value from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h index 996bb58b0..8fbd95c38 100644 --- a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -567,29 +567,29 @@ // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes #define DELTA_CALIBRATION_RADIUS 121.5 // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 151.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 151.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 356.5 // (mm) + #define DELTA_DIAGONAL_ROD 356.5 // (mm) - // height from z=0 to home position - #define DELTA_HEIGHT 352.00 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 352.00 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 176.5 //mm Get this value from auto calibrate + #define DELTA_RADIUS 176.5 // (mm) Get this value from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h b/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h index c66e9f744..b0fac96f3 100644 --- a/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h +++ b/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h @@ -552,29 +552,29 @@ // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes #define DELTA_CALIBRATION_RADIUS 121.5 // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 140.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 140.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 250.0 // (mm) + #define DELTA_DIAGONAL_ROD 250.0 // (mm) - // height from z=0 to home position - #define DELTA_HEIGHT 250.00 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 250.00 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 124.0 //mm Get this value from auto calibrate + #define DELTA_RADIUS 124.0 // (mm) Get this value from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h b/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h index c65ededaa..d700ada3e 100644 --- a/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h @@ -554,31 +554,31 @@ #if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU) // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes - #define DELTA_CALIBRATION_RADIUS 140 // (mm) + #define DELTA_CALIBRATION_RADIUS 140 // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 165.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 165.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 397.19 // (mm) + #define DELTA_DIAGONAL_ROD 397.19 // (mm) - // height from z=0 to home position - #define DELTA_HEIGHT 522.27 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 522.27 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, -0.12, -0.78 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, -0.12, -0.78 } // Get these values from G33 auto calibrate // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 157.39 //mm Get this value from auto calibrate + #define DELTA_RADIUS 157.39 // (mm) Get this value from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { -0.18, 0.18, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { -0.18, 0.18, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/Marlin/src/config/examples/delta/generic/Configuration.h b/Marlin/src/config/examples/delta/generic/Configuration.h index 29bb6f54f..d96552791 100644 --- a/Marlin/src/config/examples/delta/generic/Configuration.h +++ b/Marlin/src/config/examples/delta/generic/Configuration.h @@ -552,29 +552,29 @@ // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes #define DELTA_CALIBRATION_RADIUS 121.5 // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 140.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 140.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 250.0 // (mm) + #define DELTA_DIAGONAL_ROD 250.0 // (mm) - // height from z=0 to home position - #define DELTA_HEIGHT 250.00 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 250.00 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 124.0 //mm Get this value from auto calibrate + #define DELTA_RADIUS 124.0 // (mm) Get this value from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h index 8185306dc..2b49114c7 100644 --- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h @@ -552,29 +552,29 @@ // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes #define DELTA_CALIBRATION_RADIUS 78.0 // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 90.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 90.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 215.0 // (mm) + #define DELTA_DIAGONAL_ROD 215.0 // (mm) - // height from z=0 to home position - #define DELTA_HEIGHT 250.00 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 250.00 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 105.2 //mm Get this value from auto calibrate + #define DELTA_RADIUS 105.2 // (mm) Get this value from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h index 33f43cbec..be8534b91 100644 --- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h @@ -538,29 +538,29 @@ // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes #define DELTA_CALIBRATION_RADIUS 110.0 // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 127.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 127.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 301.0 // (mm) + #define DELTA_DIAGONAL_ROD 301.0 // (mm) - // height from z=0 to home position - #define DELTA_HEIGHT 277.00 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 277.00 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 152.357 //mm Get this value from auto calibrate + #define DELTA_RADIUS 152.357 // (mm) Get this value from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h index f5aa6b593..518553b5a 100644 --- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h @@ -556,29 +556,29 @@ // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes #define DELTA_CALIBRATION_RADIUS 121.5 // (mm) // Set the steprate for papertest probing - #define PROBE_MANUALLY_STEP 0.05 // (mm) + #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers). - #define DELTA_PRINTABLE_RADIUS 140.0 // (mm) + #define DELTA_PRINTABLE_RADIUS 140.0 // (mm) // Center-to-center distance of the holes in the diagonal push rods. - #define DELTA_DIAGONAL_ROD 319.5 // (mm) + #define DELTA_DIAGONAL_ROD 319.5 // (mm) - // height from z=0 to home position - #define DELTA_HEIGHT 380.00 // get this value from auto calibrate + // Distance between bed and nozzle Z home position + #define DELTA_HEIGHT 380.00 // (mm) Get this value from G33 auto calibrate - #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate + #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate // Horizontal distance bridged by diagonal push rods when effector is centered. - #define DELTA_RADIUS 174.1 //mm Get this value from auto calibrate + #define DELTA_RADIUS 174.1 // (mm) Get this value from G33 auto calibrate // Trim adjustments for individual towers // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0 // measured in degrees anticlockwise looking from above the printer - #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate + #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate - // delta radius and diaginal rod adjustments measured in mm + // Delta radius and diagonal rod adjustments (mm) //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 } //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 } diff --git a/buildroot/share/fonts/README.md b/buildroot/share/fonts/README.md index ee9d8e00b..4e6f6f9b1 100644 --- a/buildroot/share/fonts/README.md +++ b/buildroot/share/fonts/README.md @@ -16,7 +16,7 @@ http://creativecommons.org/publicdomain/zero/1.0/ - ISO10646_Kana.fon ([fe2bd23](https://github.com/MarlinFirmware/Marlin/commit/fe2bd237d556439499dfdee852c1550c7a16430a)) - Marlin_symbols.fon ([fe2bd23](https://github.com/MarlinFirmware/Marlin/commit/fe2bd237d556439499dfdee852c1550c7a16430a)) -Additional changes to the original font files being distritubted with Marlin are copyrighted under the terms of the [GPLv3](http://www.gnu.org/licenses/gpl-3.0.txt) license. +Additional changes to the original font files distributed with Marlin are copyrighted under the terms of the [GPLv3](http://www.gnu.org/licenses/gpl-3.0.txt) license. ## Documentation