Add a ported example configuration for the Velleman K8400 (Vertex) printer.
Supports both dual and single head printers (with the correct config). Includes community sourced feed rate fix. Rename / move files. Remove redundant definitions.
This commit is contained in:
Anthony Birkett
parent
1236a3b3ab
commit
a0b00d29e3
9 changed files with 3255 additions and 3 deletions
|
|
@ -60,7 +60,8 @@
|
|||
#define BOARD_ULTIMAKER_OLD 71 // Ultimaker (Older electronics. Pre 1.5.4. This is rare)
|
||||
#define BOARD_ULTIMAIN_2 72 // Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
||||
#define BOARD_3DRAG 77 // 3Drag Controller
|
||||
#define BOARD_K8200 78 // Vellemann K8200 Controller (derived from 3Drag Controller)
|
||||
#define BOARD_K8200 78 // Velleman K8200 Controller (derived from 3Drag Controller)
|
||||
#define BOARD_K8400 79 // Velleman K8400 Controller (derived from 3Drag Controller)
|
||||
#define BOARD_TEENSYLU 8 // Teensylu
|
||||
#define BOARD_RUMBA 80 // Rumba
|
||||
#define BOARD_PRINTRBOARD 81 // Printrboard (AT90USB1286)
|
||||
|
|
|
|||
1216
Marlin/example_configurations/K8400/Configuration.h
Normal file
1216
Marlin/example_configurations/K8400/Configuration.h
Normal file
|
|
@ -0,0 +1,1216 @@
|
|||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Configuration.h
|
||||
*
|
||||
* Basic settings such as:
|
||||
*
|
||||
* - Type of electronics
|
||||
* - Type of temperature sensor
|
||||
* - Printer geometry
|
||||
* - Endstop configuration
|
||||
* - LCD controller
|
||||
* - Extra features
|
||||
*
|
||||
* Advanced settings can be found in Configuration_adv.h
|
||||
*
|
||||
*/
|
||||
#ifndef CONFIGURATION_H
|
||||
#define CONFIGURATION_H
|
||||
|
||||
/**
|
||||
*
|
||||
* ***********************************
|
||||
* ** ATTENTION TO ALL DEVELOPERS **
|
||||
* ***********************************
|
||||
*
|
||||
* You must increment this version number for every significant change such as,
|
||||
* but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
|
||||
*
|
||||
* Note: Update also Version.h !
|
||||
*/
|
||||
#define CONFIGURATION_H_VERSION 010100
|
||||
|
||||
#include "boards.h"
|
||||
#include "macros.h"
|
||||
|
||||
//===========================================================================
|
||||
//============================= Getting Started =============================
|
||||
//===========================================================================
|
||||
|
||||
/**
|
||||
* Here are some standard links for getting your machine calibrated:
|
||||
*
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://youtu.be/wAL9d7FgInk
|
||||
* http://calculator.josefprusa.cz
|
||||
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||||
* http://www.thingiverse.com/thing:5573
|
||||
* https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
|
||||
* http://www.thingiverse.com/thing:298812
|
||||
*/
|
||||
|
||||
//===========================================================================
|
||||
//============================= DELTA Printer ===============================
|
||||
//===========================================================================
|
||||
// For a Delta printer replace the configuration files with the files in the
|
||||
// example_configurations/delta directory.
|
||||
//
|
||||
|
||||
//===========================================================================
|
||||
//============================= SCARA Printer ===============================
|
||||
//===========================================================================
|
||||
// For a Scara printer replace the configuration files with the files in the
|
||||
// example_configurations/SCARA directory.
|
||||
//
|
||||
|
||||
// @section info
|
||||
|
||||
#if ENABLED(USE_AUTOMATIC_VERSIONING)
|
||||
#include "_Version.h"
|
||||
#else
|
||||
#include "Version.h"
|
||||
#endif
|
||||
|
||||
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
||||
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
|
||||
// build by the user have been successfully uploaded into firmware.
|
||||
#define STRING_CONFIG_H_AUTHOR "(Anthony Birkett, default config)" // Who made the changes.
|
||||
#define SHOW_BOOTSCREEN
|
||||
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
|
||||
//#define STRING_SPLASH_LINE2 STRING_DISTRIBUTION_DATE // will be shown during bootup in line 2
|
||||
|
||||
// @section machine
|
||||
|
||||
// SERIAL_PORT selects which serial port should be used for communication with the host.
|
||||
// This allows the connection of wireless adapters (for instance) to non-default port pins.
|
||||
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
|
||||
// :[0,1,2,3,4,5,6,7]
|
||||
#define SERIAL_PORT 0
|
||||
|
||||
// This determines the communication speed of the printer
|
||||
// :[2400,9600,19200,38400,57600,115200,250000]
|
||||
#define BAUDRATE 250000
|
||||
|
||||
// Enable the Bluetooth serial interface on AT90USB devices
|
||||
//#define BLUETOOTH
|
||||
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_K8400
|
||||
#endif
|
||||
|
||||
// Optional custom name for your RepStrap or other custom machine
|
||||
// Displayed in the LCD "Ready" message
|
||||
//#define CUSTOM_MACHINE_NAME "3D Printer"
|
||||
|
||||
// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1,2,3,4]
|
||||
#define EXTRUDERS 1
|
||||
|
||||
// For Cyclops or any "multi-extruder" that shares a single nozzle.
|
||||
//#define SINGLENOZZLE
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||
// For the other hotends it is their distance from the extruder 0 hotend.
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
//// The following define selects which power supply you have. Please choose the one that matches your setup
|
||||
// 1 = ATX
|
||||
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
|
||||
// :{1:'ATX',2:'X-Box 360'}
|
||||
|
||||
#define POWER_SUPPLY 1
|
||||
|
||||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
//#define PS_DEFAULT_OFF
|
||||
|
||||
// @section temperature
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Settings ============================
|
||||
//===========================================================================
|
||||
//
|
||||
//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
|
||||
//
|
||||
//// Temperature sensor settings:
|
||||
// -3 is thermocouple with MAX31855 (only for sensor 0)
|
||||
// -2 is thermocouple with MAX6675 (only for sensor 0)
|
||||
// -1 is thermocouple with AD595
|
||||
// 0 is not used
|
||||
// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
|
||||
// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
|
||||
// 3 is Mendel-parts thermistor (4.7k pullup)
|
||||
// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
|
||||
// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
|
||||
// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
|
||||
// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
|
||||
// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
|
||||
// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
|
||||
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
|
||||
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
|
||||
// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
|
||||
// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
|
||||
// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
|
||||
// 20 is the PT100 circuit found in the Ultimainboard V2.x
|
||||
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
|
||||
// 70 is the 100K thermistor found in the bq Hephestos 2
|
||||
//
|
||||
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
|
||||
// (but gives greater accuracy and more stable PID)
|
||||
// 51 is 100k thermistor - EPCOS (1k pullup)
|
||||
// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
|
||||
// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
|
||||
//
|
||||
// 1047 is Pt1000 with 4k7 pullup
|
||||
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
// 147 is Pt100 with 4k7 pullup
|
||||
// 110 is Pt100 with 1k pullup (non standard)
|
||||
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
//#define DUMMY_THERMISTOR_998_VALUE 25
|
||||
//#define DUMMY_THERMISTOR_999_VALUE 100
|
||||
// :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-3': "Thermocouple + MAX31855 (only for sensor 0)", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" }
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
#define TEMP_SENSOR_BED 0
|
||||
|
||||
// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
|
||||
//#define TEMP_SENSOR_1_AS_REDUNDANT
|
||||
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
|
||||
|
||||
// Extruder temperature must be close to target for this long before M109 returns success
|
||||
#define TEMP_RESIDENCY_TIME 2 // (seconds)
|
||||
#define TEMP_HYSTERESIS 5 // (degC) range of +/- temperatures considered "close" to the target one
|
||||
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
|
||||
|
||||
// Bed temperature must be close to target for this long before M190 returns success
|
||||
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds)
|
||||
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
|
||||
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
|
||||
|
||||
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
|
||||
// to check that the wiring to the thermistor is not broken.
|
||||
// Otherwise this would lead to the heater being powered on all the time.
|
||||
#define HEATER_0_MINTEMP 5
|
||||
#define HEATER_1_MINTEMP 5
|
||||
#define HEATER_2_MINTEMP 5
|
||||
#define HEATER_3_MINTEMP 5
|
||||
#define BED_MINTEMP 5
|
||||
|
||||
// When temperature exceeds max temp, your heater will be switched off.
|
||||
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
|
||||
// You should use MINTEMP for thermistor short/failure protection.
|
||||
#define HEATER_0_MAXTEMP 275
|
||||
#define HEATER_1_MAXTEMP 275
|
||||
#define HEATER_2_MAXTEMP 275
|
||||
#define HEATER_3_MAXTEMP 275
|
||||
#define BED_MAXTEMP 150
|
||||
|
||||
// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
|
||||
//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R
|
||||
//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID Settings ================================
|
||||
//===========================================================================
|
||||
// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
|
||||
|
||||
// Comment the following line to disable PID and enable bang-bang.
|
||||
#define PIDTEMP
|
||||
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
||||
#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
|
||||
//#define PID_DEBUG // Sends debug data to the serial port.
|
||||
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
//#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
|
||||
#define K1 0.95 //smoothing factor within the PID
|
||||
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
// Ultimaker
|
||||
//#define DEFAULT_Kp 22.2
|
||||
//#define DEFAULT_Ki 1.08
|
||||
//#define DEFAULT_Kd 114
|
||||
|
||||
// MakerGear
|
||||
//#define DEFAULT_Kp 7.0
|
||||
//#define DEFAULT_Ki 0.1
|
||||
//#define DEFAULT_Kd 12
|
||||
|
||||
// Mendel Parts V9 on 12V
|
||||
#define DEFAULT_Kp 63.0
|
||||
#define DEFAULT_Ki 2.25
|
||||
#define DEFAULT_Kd 440
|
||||
|
||||
#endif // PIDTEMP
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
//#define PID_BED_DEBUG // Sends debug data to the serial port.
|
||||
|
||||
#define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
#define DEFAULT_bedKp 10.00
|
||||
#define DEFAULT_bedKi .023
|
||||
#define DEFAULT_bedKd 305.4
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from pidautotune
|
||||
//#define DEFAULT_bedKp 97.1
|
||||
//#define DEFAULT_bedKi 1.41
|
||||
//#define DEFAULT_bedKd 1675.16
|
||||
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#endif // PIDTEMPBED
|
||||
|
||||
// @section extruder
|
||||
|
||||
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
||||
//can be software-disabled for whatever purposes by
|
||||
#define PREVENT_DANGEROUS_EXTRUDE
|
||||
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
|
||||
#define PREVENT_LENGTHY_EXTRUDE
|
||||
|
||||
#define EXTRUDE_MINTEMP 160
|
||||
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
||||
|
||||
//===========================================================================
|
||||
//======================== Thermal Runaway Protection =======================
|
||||
//===========================================================================
|
||||
|
||||
/**
|
||||
* Thermal Protection protects your printer from damage and fire if a
|
||||
* thermistor falls out or temperature sensors fail in any way.
|
||||
*
|
||||
* The issue: If a thermistor falls out or a temperature sensor fails,
|
||||
* Marlin can no longer sense the actual temperature. Since a disconnected
|
||||
* thermistor reads as a low temperature, the firmware will keep the heater on.
|
||||
*
|
||||
* If you get "Thermal Runaway" or "Heating failed" errors the
|
||||
* details can be tuned in Configuration_adv.h
|
||||
*/
|
||||
|
||||
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
|
||||
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
|
||||
|
||||
//===========================================================================
|
||||
//============================= Mechanical Settings =========================
|
||||
//===========================================================================
|
||||
|
||||
// @section machine
|
||||
|
||||
// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
|
||||
//#define COREXY
|
||||
//#define COREXZ
|
||||
//#define COREYZ
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
//#define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
//===========================================================================
|
||||
//============================== Endstop Settings ===========================
|
||||
//===========================================================================
|
||||
|
||||
// @section homing
|
||||
|
||||
// Specify here all the endstop connectors that are connected to any endstop or probe.
|
||||
// Almost all printers will be using one per axis. Probes will use one or more of the
|
||||
// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
|
||||
#define USE_XMIN_PLUG
|
||||
#define USE_YMIN_PLUG
|
||||
#define USE_ZMIN_PLUG
|
||||
//#define USE_XMAX_PLUG
|
||||
//#define USE_YMAX_PLUG
|
||||
//#define USE_ZMAX_PLUG
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
#if DISABLED(ENDSTOPPULLUPS)
|
||||
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
||||
//#define ENDSTOPPULLUP_XMAX
|
||||
//#define ENDSTOPPULLUP_YMAX
|
||||
//#define ENDSTOPPULLUP_ZMAX
|
||||
//#define ENDSTOPPULLUP_XMIN
|
||||
//#define ENDSTOPPULLUP_YMIN
|
||||
//#define ENDSTOPPULLUP_ZMIN
|
||||
//#define ENDSTOPPULLUP_ZMIN_PROBE
|
||||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
|
||||
//===========================================================================
|
||||
//============================= Z Probe Options =============================
|
||||
//===========================================================================
|
||||
|
||||
//
|
||||
// Probe Type
|
||||
// Probes are sensors/switches that are activated / deactivated before/after use.
|
||||
//
|
||||
// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
|
||||
// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below.
|
||||
//
|
||||
// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500.
|
||||
//
|
||||
|
||||
// A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
|
||||
// For example an inductive probe, or a setup that uses the nozzle to probe.
|
||||
// An inductive probe must be deactivated to go below
|
||||
// its trigger-point if hardware endstops are active.
|
||||
//#define FIX_MOUNTED_PROBE
|
||||
|
||||
// Z Servo Probe, such as an endstop switch on a rotating arm.
|
||||
//#define Z_ENDSTOP_SERVO_NR 0
|
||||
//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
|
||||
|
||||
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||
//#define Z_PROBE_SLED
|
||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||
|
||||
// Z Probe to nozzle (X,Y) offset, relative to (0, 0).
|
||||
// X and Y offsets must be integers.
|
||||
//
|
||||
// In the following example the X and Y offsets are both positive:
|
||||
// #define X_PROBE_OFFSET_FROM_EXTRUDER 10
|
||||
// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
|
||||
//
|
||||
// +-- BACK ---+
|
||||
// | |
|
||||
// L | (+) P | R <-- probe (20,20)
|
||||
// E | | I
|
||||
// F | (-) N (+) | G <-- nozzle (10,10)
|
||||
// T | | H
|
||||
// | (-) | T
|
||||
// | |
|
||||
// O-- FRONT --+
|
||||
// (0,0)
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
|
||||
|
||||
// X and Y axis travel speed (mm/m) between probes
|
||||
#define XY_PROBE_SPEED 8000
|
||||
|
||||
//
|
||||
// Allen Key Probe is defined in the Delta example configurations.
|
||||
//
|
||||
|
||||
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
|
||||
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
|
||||
//
|
||||
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
|
||||
//
|
||||
// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
|
||||
// Example: To park the head outside the bed area when homing with G28.
|
||||
//
|
||||
// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
|
||||
//
|
||||
// For a servo-based Z probe, you must set up servo support below, including
|
||||
// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
|
||||
//
|
||||
// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
|
||||
// - Use 5V for powered (usu. inductive) sensors.
|
||||
// - Otherwise connect:
|
||||
// - normally-closed switches to GND and D32.
|
||||
// - normally-open switches to 5V and D32.
|
||||
//
|
||||
// Normally-closed switches are advised and are the default.
|
||||
//
|
||||
// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
|
||||
// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
|
||||
// default pin for all RAMPS-based boards. Some other boards map differently.
|
||||
// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
|
||||
//
|
||||
// WARNING:
|
||||
// Setting the wrong pin may have unexpected and potentially disastrous consequences.
|
||||
// Use with caution and do your homework.
|
||||
//
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
|
||||
// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
|
||||
// The Z_MIN_PIN will then be used for both Z-homing and probing.
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
// To use a probe you must enable one of the two options above!
|
||||
|
||||
// This option disables the use of the Z_MIN_PROBE_PIN
|
||||
// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
|
||||
// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
|
||||
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
|
||||
//#define DISABLE_Z_MIN_PROBE_ENDSTOP
|
||||
|
||||
// Enable Z Probe Repeatability test to see how accurate your probe is
|
||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
|
||||
//
|
||||
// Probe Raise options provide clearance for the probe to deploy, stow, and travel.
|
||||
//
|
||||
#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
|
||||
#define Z_RAISE_BETWEEN_PROBINGS 5 // Raise between probing points.
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
//
|
||||
#define Z_PROBE_OFFSET_RANGE_MIN -20
|
||||
#define Z_PROBE_OFFSET_RANGE_MAX 20
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
// :{0:'Low',1:'High'}
|
||||
#define X_ENABLE_ON 0
|
||||
#define Y_ENABLE_ON 0
|
||||
#define Z_ENABLE_ON 0
|
||||
#define E_ENABLE_ON 0 // For all extruders
|
||||
|
||||
// Disables axis stepper immediately when it's not being used.
|
||||
// WARNING: When motors turn off there is a chance of losing position accuracy!
|
||||
#define DISABLE_X false
|
||||
#define DISABLE_Y false
|
||||
#define DISABLE_Z false
|
||||
// Warn on display about possibly reduced accuracy
|
||||
//#define DISABLE_REDUCED_ACCURACY_WARNING
|
||||
|
||||
// @section extruder
|
||||
|
||||
#define DISABLE_E false // For all extruders
|
||||
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
||||
|
||||
// @section machine
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Z_DIR true
|
||||
|
||||
// @section extruder
|
||||
|
||||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
#define INVERT_E0_DIR false
|
||||
#define INVERT_E1_DIR true
|
||||
#define INVERT_E2_DIR false
|
||||
#define INVERT_E3_DIR false
|
||||
|
||||
// @section homing
|
||||
//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// ENDSTOP SETTINGS:
|
||||
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
||||
// :[-1,1]
|
||||
#define X_HOME_DIR -1
|
||||
#define Y_HOME_DIR -1
|
||||
#define Z_HOME_DIR -1
|
||||
|
||||
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
|
||||
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
|
||||
// @section machine
|
||||
|
||||
// Travel limits after homing (units are in mm)
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MIN_POS 20
|
||||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS 200
|
||||
#define Y_MAX_POS 200
|
||||
#define Z_MAX_POS 190
|
||||
|
||||
//===========================================================================
|
||||
//========================= Filament Runout Sensor ==========================
|
||||
//===========================================================================
|
||||
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
|
||||
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
|
||||
// It is assumed that when logic high = filament available
|
||||
// when logic low = filament ran out
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
const bool FIL_RUNOUT_INVERTING = false; // set to true to invert the logic of the sensor.
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//============================ Mesh Bed Leveling ============================
|
||||
//===========================================================================
|
||||
|
||||
//#define MESH_BED_LEVELING // Enable mesh bed leveling.
|
||||
|
||||
#if ENABLED(MESH_BED_LEVELING)
|
||||
#define MESH_INSET 10 // Mesh inset margin on print area
|
||||
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define MESH_NUM_Y_POINTS 3
|
||||
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0.
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0]
|
||||
|
||||
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.
|
||||
|
||||
#if ENABLED(MANUAL_BED_LEVELING)
|
||||
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
|
||||
#endif // MANUAL_BED_LEVELING
|
||||
|
||||
#endif // MESH_BED_LEVELING
|
||||
|
||||
//===========================================================================
|
||||
//============================ Bed Auto Leveling ============================
|
||||
//===========================================================================
|
||||
|
||||
// @section bedlevel
|
||||
|
||||
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||
//#define DEBUG_LEVELING_FEATURE
|
||||
|
||||
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
|
||||
|
||||
// There are 2 different ways to specify probing locations:
|
||||
//
|
||||
// - "grid" mode
|
||||
// Probe several points in a rectangular grid.
|
||||
// You specify the rectangle and the density of sample points.
|
||||
// This mode is preferred because there are more measurements.
|
||||
//
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't collinear)
|
||||
// You specify the XY coordinates of all 3 points.
|
||||
|
||||
// Enable this to sample the bed in a grid (least squares solution).
|
||||
// Note: this feature generates 10KB extra code size.
|
||||
#define AUTO_BED_LEVELING_GRID
|
||||
|
||||
#if ENABLED(AUTO_BED_LEVELING_GRID)
|
||||
|
||||
#define LEFT_PROBE_BED_POSITION 15
|
||||
#define RIGHT_PROBE_BED_POSITION 170
|
||||
#define FRONT_PROBE_BED_POSITION 20
|
||||
#define BACK_PROBE_BED_POSITION 170
|
||||
|
||||
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||
|
||||
// Set the number of grid points per dimension.
|
||||
// You probably don't need more than 3 (squared=9).
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
// Arbitrary points to probe.
|
||||
// A simple cross-product is used to estimate the plane of the bed.
|
||||
#define ABL_PROBE_PT_1_X 15
|
||||
#define ABL_PROBE_PT_1_Y 180
|
||||
#define ABL_PROBE_PT_2_X 15
|
||||
#define ABL_PROBE_PT_2_Y 20
|
||||
#define ABL_PROBE_PT_3_X 170
|
||||
#define ABL_PROBE_PT_3_Y 20
|
||||
|
||||
#endif // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
|
||||
// Useful to retract a deployable Z probe.
|
||||
|
||||
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
|
||||
// it is highly recommended you also enable Z_SAFE_HOMING below!
|
||||
|
||||
#endif // AUTO_BED_LEVELING_FEATURE
|
||||
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
// With this feature enabled:
|
||||
//
|
||||
// - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
|
||||
// - If stepper drivers time out, it will need X and Y homing again before Z homing.
|
||||
// - Position the Z probe in a defined XY point before Z Homing when homing all axes (G28).
|
||||
// - Prevent Z homing when the Z probe is outside bed area.
|
||||
//#define Z_SAFE_HOMING
|
||||
|
||||
#if ENABLED(Z_SAFE_HOMING)
|
||||
#define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).
|
||||
#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
|
||||
#endif
|
||||
|
||||
|
||||
// @section motion
|
||||
|
||||
/**
|
||||
* MOVEMENT SETTINGS
|
||||
*/
|
||||
|
||||
#define HOMING_FEEDRATE {50*60, 50*60, 8*60, 0} // set the homing speeds (mm/min)
|
||||
|
||||
// default settings
|
||||
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {134.74,134.74,4266.66,148.7} // default steps per unit for Ultimaker
|
||||
#define DEFAULT_MAX_FEEDRATE {160, 160, 10, 10000} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 6000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 6000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||
|
||||
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||
#define DEFAULT_XYJERK 10.0 // (mm/sec)
|
||||
#define DEFAULT_ZJERK 0.5 // (mm/sec)
|
||||
#define DEFAULT_EJERK 20.0 // (mm/sec)
|
||||
|
||||
|
||||
//=============================================================================
|
||||
//============================= Additional Features ===========================
|
||||
//=============================================================================
|
||||
|
||||
// @section extras
|
||||
|
||||
//
|
||||
// EEPROM
|
||||
//
|
||||
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
|
||||
// M500 - stores parameters in EEPROM
|
||||
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
//define this to enable EEPROM support
|
||||
#define EEPROM_SETTINGS
|
||||
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
#define EEPROM_CHITCHAT // Please keep turned on if you can.
|
||||
#endif
|
||||
|
||||
//
|
||||
// Host Keepalive
|
||||
//
|
||||
// When enabled Marlin will send a busy status message to the host
|
||||
// every couple of seconds when it can't accept commands.
|
||||
//
|
||||
#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
|
||||
#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
|
||||
|
||||
//
|
||||
// M100 Free Memory Watcher
|
||||
//
|
||||
//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
|
||||
|
||||
//
|
||||
// G20/G21 Inch mode support
|
||||
//
|
||||
//#define INCH_MODE_SUPPORT
|
||||
|
||||
//
|
||||
// M149 Set temperature units support
|
||||
//
|
||||
//#define TEMPERATURE_UNITS_SUPPORT
|
||||
|
||||
// @section temperature
|
||||
|
||||
// Preheat Constants
|
||||
#define PLA_PREHEAT_HOTEND_TEMP 210
|
||||
#define PLA_PREHEAT_HPB_TEMP 0
|
||||
#define PLA_PREHEAT_FAN_SPEED 165 // Insert Value between 0 and 255
|
||||
|
||||
#define ABS_PREHEAT_HOTEND_TEMP 245
|
||||
#define ABS_PREHEAT_HPB_TEMP 0
|
||||
#define ABS_PREHEAT_FAN_SPEED 165 // Insert Value between 0 and 255
|
||||
|
||||
//
|
||||
// Print job timer
|
||||
//
|
||||
// Enable this option to automatically start and stop the
|
||||
// print job timer when M104 and M109 commands are received.
|
||||
//
|
||||
// In all cases the timer can be started and stopped using
|
||||
// the following commands:
|
||||
//
|
||||
// - M75 - Start the print job timer
|
||||
// - M76 - Pause the print job timer
|
||||
// - M77 - Stop the print job timer
|
||||
#define PRINTJOB_TIMER_AUTOSTART
|
||||
|
||||
//
|
||||
// Print Counter
|
||||
//
|
||||
// When enabled Marlin will keep track of some print statistical data such as:
|
||||
// - Total print jobs
|
||||
// - Total successful print jobs
|
||||
// - Total failed print jobs
|
||||
// - Total time printing
|
||||
//
|
||||
// This information can be viewed by the M78 command.
|
||||
//#define PRINTCOUNTER
|
||||
|
||||
//=============================================================================
|
||||
//============================= LCD and SD support ============================
|
||||
//=============================================================================
|
||||
|
||||
// @section lcd
|
||||
|
||||
//
|
||||
// LCD LANGUAGE
|
||||
//
|
||||
// Here you may choose the language used by Marlin on the LCD menus, the following
|
||||
// list of languages are available:
|
||||
// en, an, bg, ca, cn, cz, de, es, eu, fi, fr, gl, hr, it, kana,
|
||||
// kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, test
|
||||
//
|
||||
// :{'en':'English','an':'Aragonese','bg':'Bulgarian','ca':'Catalan','cn':'Chinese','cz':'Czech','de':'German','es':'Spanish','eu':'Basque-Euskera','fi':'Finnish','fr':'French','gl':'Galician','hr':'Croatian','it':'Italian','kana':'Japanese','kana_utf8':'Japanese (UTF8)','nl':'Dutch','pl':'Polish','pt':'Portuguese','pt-br':'Portuguese (Brazilian)','pt-br_utf8':'Portuguese (Brazilian UTF8)','pt_utf8':'Portuguese (UTF8)','ru':'Russian','test':'TEST'}
|
||||
//
|
||||
#define LCD_LANGUAGE en
|
||||
|
||||
//
|
||||
// LCD Character Set
|
||||
//
|
||||
// Note: This option is NOT applicable to Graphical Displays.
|
||||
//
|
||||
// All character-based LCD's provide ASCII plus one of these
|
||||
// language extensions:
|
||||
//
|
||||
// - JAPANESE ... the most common
|
||||
// - WESTERN ... with more accented characters
|
||||
// - CYRILLIC ... for the Russian language
|
||||
//
|
||||
// To determine the language extension installed on your controller:
|
||||
//
|
||||
// - Compile and upload with LCD_LANGUAGE set to 'test'
|
||||
// - Click the controller to view the LCD menu
|
||||
// - The LCD will display Japanese, Western, or Cyrillic text
|
||||
//
|
||||
// See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
|
||||
//
|
||||
// :['JAPANESE','WESTERN','CYRILLIC']
|
||||
//
|
||||
#define DISPLAY_CHARSET_HD44780 JAPANESE
|
||||
|
||||
//
|
||||
// LCD TYPE
|
||||
//
|
||||
// You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2,
|
||||
// 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels
|
||||
// (ST7565R family). (This option will be set automatically for certain displays.)
|
||||
//
|
||||
// IMPORTANT NOTE: The U8glib library is required for Full Graphic Display!
|
||||
// https://github.com/olikraus/U8glib_Arduino
|
||||
//
|
||||
#define ULTRA_LCD // Character based
|
||||
//#define DOGLCD // Full graphics display
|
||||
|
||||
//
|
||||
// SD CARD
|
||||
//
|
||||
// SD Card support is disabled by default. If your controller has an SD slot,
|
||||
// you must uncomment the following option or it won't work.
|
||||
//
|
||||
#define SDSUPPORT
|
||||
|
||||
//
|
||||
// SD CARD: SPI SPEED
|
||||
//
|
||||
// Uncomment ONE of the following items to use a slower SPI transfer
|
||||
// speed. This is usually required if you're getting volume init errors.
|
||||
//
|
||||
//#define SPI_SPEED SPI_HALF_SPEED
|
||||
//#define SPI_SPEED SPI_QUARTER_SPEED
|
||||
//#define SPI_SPEED SPI_EIGHTH_SPEED
|
||||
|
||||
//
|
||||
// SD CARD: ENABLE CRC
|
||||
//
|
||||
// Use CRC checks and retries on the SD communication.
|
||||
//
|
||||
//#define SD_CHECK_AND_RETRY
|
||||
|
||||
//
|
||||
// ENCODER SETTINGS
|
||||
//
|
||||
// This option overrides the default number of encoder pulses needed to
|
||||
// produce one step. Should be increased for high-resolution encoders.
|
||||
//
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
|
||||
//
|
||||
// Use this option to override the number of step signals required to
|
||||
// move between next/prev menu items.
|
||||
//
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
|
||||
/**
|
||||
* Encoder Direction Options
|
||||
*
|
||||
* Test your encoder's behavior first with both options disabled.
|
||||
*
|
||||
* Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
|
||||
* Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
|
||||
* Reversed Value Editing only? Enable BOTH options.
|
||||
*/
|
||||
|
||||
//
|
||||
// This option reverses the encoder direction everywhere
|
||||
//
|
||||
// Set this option if CLOCKWISE causes values to DECREASE
|
||||
//
|
||||
//#define REVERSE_ENCODER_DIRECTION
|
||||
|
||||
//
|
||||
// This option reverses the encoder direction for navigating LCD menus.
|
||||
//
|
||||
// If CLOCKWISE normally moves DOWN this makes it go UP.
|
||||
// If CLOCKWISE normally moves UP this makes it go DOWN.
|
||||
//
|
||||
#define REVERSE_MENU_DIRECTION
|
||||
|
||||
//
|
||||
// Individual Axis Homing
|
||||
//
|
||||
// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
|
||||
//
|
||||
//#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
|
||||
//
|
||||
// SPEAKER/BUZZER
|
||||
//
|
||||
// If you have a speaker that can produce tones, enable it here.
|
||||
// By default Marlin assumes you have a buzzer with a fixed frequency.
|
||||
//
|
||||
//#define SPEAKER
|
||||
|
||||
//
|
||||
// The duration and frequency for the UI feedback sound.
|
||||
// Set these to 0 to disable audio feedback in the LCD menus.
|
||||
//
|
||||
// Note: Test audio output with the G-Code:
|
||||
// M300 S<frequency Hz> P<duration ms>
|
||||
//
|
||||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000
|
||||
|
||||
//
|
||||
// CONTROLLER TYPE: Standard
|
||||
//
|
||||
// Marlin supports a wide variety of controllers.
|
||||
// Enable one of the following options to specify your controller.
|
||||
//
|
||||
|
||||
//
|
||||
// ULTIMAKER Controller.
|
||||
//
|
||||
#define ULTIMAKERCONTROLLER
|
||||
|
||||
//
|
||||
// ULTIPANEL as seen on Thingiverse.
|
||||
//
|
||||
//#define ULTIPANEL
|
||||
|
||||
//
|
||||
// Cartesio UI
|
||||
// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
|
||||
//
|
||||
//#define CARTESIO_UI
|
||||
|
||||
//
|
||||
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
|
||||
// http://reprap.org/wiki/PanelOne
|
||||
//
|
||||
//#define PANEL_ONE
|
||||
|
||||
//
|
||||
// MaKr3d Makr-Panel with graphic controller and SD support.
|
||||
// http://reprap.org/wiki/MaKr3d_MaKrPanel
|
||||
//
|
||||
//#define MAKRPANEL
|
||||
|
||||
//
|
||||
// Activate one of these if you have a Panucatt Devices
|
||||
// Viki 2.0 or mini Viki with Graphic LCD
|
||||
// http://panucatt.com
|
||||
//
|
||||
//#define VIKI2
|
||||
//#define miniVIKI
|
||||
|
||||
//
|
||||
// Adafruit ST7565 Full Graphic Controller.
|
||||
// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
|
||||
//
|
||||
//#define ELB_FULL_GRAPHIC_CONTROLLER
|
||||
|
||||
//
|
||||
// RepRapDiscount Smart Controller.
|
||||
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
|
||||
//
|
||||
// Note: Usually sold with a white PCB.
|
||||
//
|
||||
//#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||||
|
||||
//
|
||||
// GADGETS3D G3D LCD/SD Controller
|
||||
// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
|
||||
//
|
||||
// Note: Usually sold with a blue PCB.
|
||||
//
|
||||
//#define G3D_PANEL
|
||||
|
||||
//
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
// controller and SD support - http://reprap.org/wiki/Mini_panel
|
||||
//
|
||||
//#define MINIPANEL
|
||||
|
||||
//
|
||||
// RepRapWorld REPRAPWORLD_KEYPAD v1.1
|
||||
// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
|
||||
//
|
||||
// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
|
||||
// is pressed, a value of 10.0 means 10mm per click.
|
||||
//
|
||||
//#define REPRAPWORLD_KEYPAD
|
||||
//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
|
||||
|
||||
//
|
||||
// RigidBot Panel V1.0
|
||||
// http://www.inventapart.com/
|
||||
//
|
||||
//#define RIGIDBOT_PANEL
|
||||
|
||||
//
|
||||
// BQ LCD Smart Controller shipped by
|
||||
// default with the BQ Hephestos 2 and Witbox 2.
|
||||
//
|
||||
//#define BQ_LCD_SMART_CONTROLLER
|
||||
|
||||
//
|
||||
// CONTROLLER TYPE: I2C
|
||||
//
|
||||
// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
|
||||
// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
||||
//
|
||||
|
||||
//
|
||||
// Elefu RA Board Control Panel
|
||||
// http://www.elefu.com/index.php?route=product/product&product_id=53
|
||||
//
|
||||
//#define RA_CONTROL_PANEL
|
||||
|
||||
//
|
||||
// Sainsmart YW Robot (LCM1602) LCD Display
|
||||
//
|
||||
//#define LCD_I2C_SAINSMART_YWROBOT
|
||||
|
||||
//
|
||||
// Generic LCM1602 LCD adapter
|
||||
//
|
||||
//#define LCM1602
|
||||
|
||||
//
|
||||
// PANELOLU2 LCD with status LEDs,
|
||||
// separate encoder and click inputs.
|
||||
//
|
||||
// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
|
||||
// For more info: https://github.com/lincomatic/LiquidTWI2
|
||||
//
|
||||
// Note: The PANELOLU2 encoder click input can either be directly connected to
|
||||
// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
|
||||
//
|
||||
//#define LCD_I2C_PANELOLU2
|
||||
|
||||
//
|
||||
// Panucatt VIKI LCD with status LEDs,
|
||||
// integrated click & L/R/U/D buttons, separate encoder inputs.
|
||||
//
|
||||
//#define LCD_I2C_VIKI
|
||||
|
||||
//
|
||||
// SSD1306 OLED full graphics generic display
|
||||
//
|
||||
//#define U8GLIB_SSD1306
|
||||
|
||||
//
|
||||
// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
|
||||
//
|
||||
//#define SAV_3DGLCD
|
||||
#if ENABLED(SAV_3DGLCD)
|
||||
//#define U8GLIB_SSD1306
|
||||
#define U8GLIB_SH1106
|
||||
#endif
|
||||
|
||||
//
|
||||
// CONTROLLER TYPE: Shift register panels
|
||||
//
|
||||
// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
|
||||
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
|
||||
//
|
||||
//#define SAV_3DLCD
|
||||
|
||||
//=============================================================================
|
||||
//=============================== Extra Features ==============================
|
||||
//=============================================================================
|
||||
|
||||
// @section extras
|
||||
|
||||
// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||||
//#define FAST_PWM_FAN
|
||||
|
||||
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
|
||||
// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
|
||||
// is too low, you should also increment SOFT_PWM_SCALE.
|
||||
//#define FAN_SOFT_PWM
|
||||
|
||||
// Incrementing this by 1 will double the software PWM frequency,
|
||||
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
|
||||
// However, control resolution will be halved for each increment;
|
||||
// at zero value, there are 128 effective control positions.
|
||||
#define SOFT_PWM_SCALE 0
|
||||
|
||||
// Temperature status LEDs that display the hotend and bed temperature.
|
||||
// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
|
||||
// Otherwise the RED led is on. There is 1C hysteresis.
|
||||
//#define TEMP_STAT_LEDS
|
||||
|
||||
// M240 Triggers a camera by emulating a Canon RC-1 Remote
|
||||
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
||||
//#define PHOTOGRAPH_PIN 23
|
||||
|
||||
// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
|
||||
//#define SF_ARC_FIX
|
||||
|
||||
// Support for the BariCUDA Paste Extruder.
|
||||
//#define BARICUDA
|
||||
|
||||
//define BlinkM/CyzRgb Support
|
||||
//#define BLINKM
|
||||
|
||||
/*********************************************************************\
|
||||
* R/C SERVO support
|
||||
* Sponsored by TrinityLabs, Reworked by codexmas
|
||||
**********************************************************************/
|
||||
|
||||
// Number of servos
|
||||
//
|
||||
// If you select a configuration below, this will receive a default value and does not need to be set manually
|
||||
// set it manually if you have more servos than extruders and wish to manually control some
|
||||
// leaving it undefined or defining as 0 will disable the servo subsystem
|
||||
// If unsure, leave commented / disabled
|
||||
//
|
||||
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
|
||||
|
||||
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
|
||||
// 300ms is a good value but you can try less delay.
|
||||
// If the servo can't reach the requested position, increase it.
|
||||
#define SERVO_DELAY 300
|
||||
|
||||
// Servo deactivation
|
||||
//
|
||||
// With this option servos are powered only during movement, then turned off to prevent jitter.
|
||||
//#define DEACTIVATE_SERVOS_AFTER_MOVE
|
||||
|
||||
/**********************************************************************\
|
||||
* Support for a filament diameter sensor
|
||||
* Also allows adjustment of diameter at print time (vs at slicing)
|
||||
* Single extruder only at this point (extruder 0)
|
||||
*
|
||||
* Motherboards
|
||||
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
|
||||
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
|
||||
* 301 - Rambo - uses Analog input 3
|
||||
* Note may require analog pins to be defined for different motherboards
|
||||
**********************************************************************/
|
||||
// Uncomment below to enable
|
||||
//#define FILAMENT_WIDTH_SENSOR
|
||||
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
|
||||
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
|
||||
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
|
||||
|
||||
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
|
||||
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
|
||||
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
|
||||
|
||||
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
|
||||
//#define FILAMENT_LCD_DISPLAY
|
||||
#endif
|
||||
|
||||
#include "Configuration_adv.h"
|
||||
#include "thermistortables.h"
|
||||
|
||||
#endif //CONFIGURATION_H
|
||||
750
Marlin/example_configurations/K8400/Configuration_adv.h
Normal file
750
Marlin/example_configurations/K8400/Configuration_adv.h
Normal file
|
|
@ -0,0 +1,750 @@
|
|||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Configuration_adv.h
|
||||
*
|
||||
* Advanced settings.
|
||||
* Only change these if you know exactly what you're doing.
|
||||
* Some of these settings can damage your printer if improperly set!
|
||||
*
|
||||
* Basic settings can be found in Configuration.h
|
||||
*
|
||||
*/
|
||||
#ifndef CONFIGURATION_ADV_H
|
||||
#define CONFIGURATION_ADV_H
|
||||
|
||||
/**
|
||||
*
|
||||
* ***********************************
|
||||
* ** ATTENTION TO ALL DEVELOPERS **
|
||||
* ***********************************
|
||||
*
|
||||
* You must increment this version number for every significant change such as,
|
||||
* but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
|
||||
*
|
||||
* Note: Update also Version.h !
|
||||
*/
|
||||
#define CONFIGURATION_ADV_H_VERSION 010100
|
||||
|
||||
#include "Conditionals.h"
|
||||
|
||||
// @section temperature
|
||||
|
||||
//===========================================================================
|
||||
//=============================Thermal Settings ============================
|
||||
//===========================================================================
|
||||
|
||||
#if DISABLED(PIDTEMPBED)
|
||||
#define BED_CHECK_INTERVAL 1000 // ms between checks in bang-bang control
|
||||
#if ENABLED(BED_LIMIT_SWITCHING)
|
||||
#define BED_HYSTERESIS 1 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Thermal Protection protects your printer from damage and fire if a
|
||||
* thermistor falls out or temperature sensors fail in any way.
|
||||
*
|
||||
* The issue: If a thermistor falls out or a temperature sensor fails,
|
||||
* Marlin can no longer sense the actual temperature. Since a disconnected
|
||||
* thermistor reads as a low temperature, the firmware will keep the heater on.
|
||||
*
|
||||
* The solution: Once the temperature reaches the target, start observing.
|
||||
* If the temperature stays too far below the target (hysteresis) for too long (period),
|
||||
* the firmware will halt the machine as a safety precaution.
|
||||
*
|
||||
* If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS)
|
||||
#define THERMAL_PROTECTION_PERIOD 40 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
|
||||
|
||||
/**
|
||||
* Whenever an M104 or M109 increases the target temperature the firmware will wait for the
|
||||
* WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
|
||||
* degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
|
||||
* but only if the current temperature is far enough below the target for a reliable test.
|
||||
*
|
||||
* If you get false positives for "Heating failed" increase WATCH_TEMP_PERIOD and/or decrease WATCH_TEMP_INCREASE
|
||||
* WATCH_TEMP_INCREASE should not be below 2.
|
||||
*/
|
||||
#define WATCH_TEMP_PERIOD 20 // Seconds
|
||||
#define WATCH_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Thermal Protection parameters for the bed are just as above for hotends.
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_BED)
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
|
||||
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
|
||||
|
||||
/**
|
||||
* Whenever an M140 or M190 increases the target temperature the firmware will wait for the
|
||||
* WATCH_BED_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_BED_TEMP_INCREASE
|
||||
* degrees, the machine is halted, requiring a hard reset. This test restarts with any M140/M190,
|
||||
* but only if the current temperature is far enough below the target for a reliable test.
|
||||
*
|
||||
* If you get too many "Heating failed" errors, increase WATCH_BED_TEMP_PERIOD and/or decrease
|
||||
* WATCH_BED_TEMP_INCREASE. (WATCH_BED_TEMP_INCREASE should not be below 2.)
|
||||
*/
|
||||
#define WATCH_BED_TEMP_PERIOD 60 // Seconds
|
||||
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
// this adds an experimental additional term to the heating power, proportional to the extrusion speed.
|
||||
// if Kc is chosen well, the additional required power due to increased melting should be compensated.
|
||||
#define PID_ADD_EXTRUSION_RATE
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
|
||||
#define LPQ_MAX_LEN 50
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Automatic Temperature:
|
||||
* The hotend target temperature is calculated by all the buffered lines of gcode.
|
||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||
*/
|
||||
#define AUTOTEMP
|
||||
#if ENABLED(AUTOTEMP)
|
||||
#define AUTOTEMP_OLDWEIGHT 0.98
|
||||
#endif
|
||||
|
||||
//Show Temperature ADC value
|
||||
//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
|
||||
//#define SHOW_TEMP_ADC_VALUES
|
||||
|
||||
// @section extruder
|
||||
|
||||
// extruder run-out prevention.
|
||||
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
|
||||
//#define EXTRUDER_RUNOUT_PREVENT
|
||||
#define EXTRUDER_RUNOUT_MINTEMP 190
|
||||
#define EXTRUDER_RUNOUT_SECONDS 30
|
||||
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
|
||||
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
|
||||
#define EXTRUDER_RUNOUT_EXTRUDE 100
|
||||
|
||||
// @section temperature
|
||||
|
||||
//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
|
||||
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
|
||||
#define TEMP_SENSOR_AD595_OFFSET 0.0
|
||||
#define TEMP_SENSOR_AD595_GAIN 1.0
|
||||
|
||||
//This is for controlling a fan to cool down the stepper drivers
|
||||
//it will turn on when any driver is enabled
|
||||
//and turn off after the set amount of seconds from last driver being disabled again
|
||||
#define CONTROLLERFAN_PIN 2 //Pin used for the fan to cool controller (-1 to disable)
|
||||
#define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run
|
||||
#define CONTROLLERFAN_SPEED 255 // == full speed
|
||||
|
||||
// When first starting the main fan, run it at full speed for the
|
||||
// given number of milliseconds. This gets the fan spinning reliably
|
||||
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
|
||||
//#define FAN_KICKSTART_TIME 100
|
||||
|
||||
// This defines the minimal speed for the main fan, run in PWM mode
|
||||
// to enable uncomment and set minimal PWM speed for reliable running (1-255)
|
||||
// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
|
||||
//#define FAN_MIN_PWM 50
|
||||
|
||||
// @section extruder
|
||||
|
||||
// Extruder cooling fans
|
||||
// Configure fan pin outputs to automatically turn on/off when the associated
|
||||
// extruder temperature is above/below EXTRUDER_AUTO_FAN_TEMPERATURE.
|
||||
// Multiple extruders can be assigned to the same pin in which case
|
||||
// the fan will turn on when any selected extruder is above the threshold.
|
||||
#define EXTRUDER_0_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_1_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_2_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_3_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
|
||||
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//=============================Mechanical Settings===========================
|
||||
//===========================================================================
|
||||
|
||||
// @section homing
|
||||
|
||||
#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
|
||||
|
||||
// @section extras
|
||||
|
||||
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
|
||||
|
||||
// A single Z stepper driver is usually used to drive 2 stepper motors.
|
||||
// Uncomment this define to utilize a separate stepper driver for each Z axis motor.
|
||||
// Only a few motherboards support this, like RAMPS, which have dual extruder support (the 2nd, often unused, extruder driver is used
|
||||
// to control the 2nd Z axis stepper motor). The pins are currently only defined for a RAMPS motherboards.
|
||||
// On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
|
||||
//#define Z_DUAL_STEPPER_DRIVERS
|
||||
|
||||
#if ENABLED(Z_DUAL_STEPPER_DRIVERS)
|
||||
|
||||
// Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
|
||||
// That way the machine is capable to align the bed during home, since both Z steppers are homed.
|
||||
// There is also an implementation of M666 (software endstops adjustment) to this feature.
|
||||
// After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
|
||||
// One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
|
||||
// If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
|
||||
// Play a little bit with small adjustments (0.5mm) and check the behaviour.
|
||||
// The M119 (endstops report) will start reporting the Z2 Endstop as well.
|
||||
|
||||
//#define Z_DUAL_ENDSTOPS
|
||||
|
||||
#if ENABLED(Z_DUAL_ENDSTOPS)
|
||||
#define Z2_USE_ENDSTOP _XMAX_
|
||||
#endif
|
||||
|
||||
#endif // Z_DUAL_STEPPER_DRIVERS
|
||||
|
||||
// Same again but for Y Axis.
|
||||
//#define Y_DUAL_STEPPER_DRIVERS
|
||||
|
||||
#if ENABLED(Y_DUAL_STEPPER_DRIVERS)
|
||||
// Define if the two Y drives need to rotate in opposite directions
|
||||
#define INVERT_Y2_VS_Y_DIR true
|
||||
#endif
|
||||
|
||||
// Enable this for dual x-carriage printers.
|
||||
// A dual x-carriage design has the advantage that the inactive extruder can be parked which
|
||||
// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
|
||||
// allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
|
||||
//#define DUAL_X_CARRIAGE
|
||||
#if ENABLED(DUAL_X_CARRIAGE)
|
||||
// Configuration for second X-carriage
|
||||
// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
|
||||
// the second x-carriage always homes to the maximum endstop.
|
||||
#define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
|
||||
#define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
|
||||
#define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
|
||||
#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
|
||||
// However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
|
||||
// override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
|
||||
// without modifying the firmware (through the "M218 T1 X???" command).
|
||||
// Remember: you should set the second extruder x-offset to 0 in your slicer.
|
||||
|
||||
// There are a few selectable movement modes for dual x-carriages using M605 S<mode>
|
||||
// Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
|
||||
// as long as it supports dual x-carriages. (M605 S0)
|
||||
// Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
|
||||
// that additional slicer support is not required. (M605 S1)
|
||||
// Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
|
||||
// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
|
||||
// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
|
||||
|
||||
// This is the default power-up mode which can be later using M605.
|
||||
#define DEFAULT_DUAL_X_CARRIAGE_MODE 0
|
||||
|
||||
// Default settings in "Auto-park Mode"
|
||||
#define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
|
||||
#define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
|
||||
|
||||
// Default x offset in duplication mode (typically set to half print bed width)
|
||||
#define DEFAULT_DUPLICATION_X_OFFSET 100
|
||||
|
||||
#endif //DUAL_X_CARRIAGE
|
||||
|
||||
// @section homing
|
||||
|
||||
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
|
||||
#define X_HOME_BUMP_MM 10
|
||||
#define Y_HOME_BUMP_MM 10
|
||||
#define Z_HOME_BUMP_MM 3
|
||||
#define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||
#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||
|
||||
// When G28 is called, this option will make Y home before X
|
||||
//#define HOME_Y_BEFORE_X
|
||||
|
||||
// @section machine
|
||||
|
||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||
|
||||
//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
|
||||
#define INVERT_X_STEP_PIN false
|
||||
#define INVERT_Y_STEP_PIN false
|
||||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
|
||||
// Time can be set by M18 and M84.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 120
|
||||
#define DISABLE_INACTIVE_X true
|
||||
#define DISABLE_INACTIVE_Y true
|
||||
#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
|
||||
#define DISABLE_INACTIVE_E true
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// @section lcd
|
||||
|
||||
#if ENABLED(ULTIPANEL)
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
#define DEFAULT_MINSEGMENTTIME 20000
|
||||
|
||||
// If defined the movements slow down when the look ahead buffer is only half full
|
||||
#define SLOWDOWN
|
||||
|
||||
// Frequency limit
|
||||
// See nophead's blog for more info
|
||||
// Not working O
|
||||
//#define XY_FREQUENCY_LIMIT 15
|
||||
|
||||
// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
|
||||
// of the buffer and all stops. This should not be much greater than zero and should only be changed
|
||||
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
|
||||
#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec)
|
||||
|
||||
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
|
||||
#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
|
||||
|
||||
// Motor Current setting (Only functional when motor driver current ref pins are connected to a digital trimpot on supported boards)
|
||||
#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
|
||||
|
||||
// Motor Current controlled via PWM (Overridable on supported boards with PWM-driven motor driver current)
|
||||
//#define PWM_MOTOR_CURRENT {1300, 1300, 1250} // Values in milliamps
|
||||
|
||||
// uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
|
||||
//#define DIGIPOT_I2C
|
||||
// Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
|
||||
#define DIGIPOT_I2C_NUM_CHANNELS 8
|
||||
// actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
|
||||
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}
|
||||
|
||||
//===========================================================================
|
||||
//=============================Additional Features===========================
|
||||
//===========================================================================
|
||||
|
||||
#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
|
||||
#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
|
||||
#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
|
||||
|
||||
//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
|
||||
#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
|
||||
|
||||
// @section lcd
|
||||
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
//#define LCD_INFO_MENU
|
||||
|
||||
#if ENABLED(SDSUPPORT)
|
||||
|
||||
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
|
||||
// around this by connecting a push button or single throw switch to the pin defined
|
||||
// as SD_DETECT_PIN in your board's pins definitions.
|
||||
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
|
||||
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
|
||||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
|
||||
#define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
|
||||
// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
|
||||
// using:
|
||||
//#define MENU_ADDAUTOSTART
|
||||
|
||||
// Show a progress bar on HD44780 LCDs for SD printing
|
||||
//#define LCD_PROGRESS_BAR
|
||||
|
||||
#if ENABLED(LCD_PROGRESS_BAR)
|
||||
// Amount of time (ms) to show the bar
|
||||
#define PROGRESS_BAR_BAR_TIME 2000
|
||||
// Amount of time (ms) to show the status message
|
||||
#define PROGRESS_BAR_MSG_TIME 3000
|
||||
// Amount of time (ms) to retain the status message (0=forever)
|
||||
#define PROGRESS_MSG_EXPIRE 0
|
||||
// Enable this to show messages for MSG_TIME then hide them
|
||||
//#define PROGRESS_MSG_ONCE
|
||||
#endif
|
||||
|
||||
// This allows hosts to request long names for files and folders with M33
|
||||
//#define LONG_FILENAME_HOST_SUPPORT
|
||||
|
||||
// This option allows you to abort SD printing when any endstop is triggered.
|
||||
// This feature must be enabled with "M540 S1" or from the LCD menu.
|
||||
// To have any effect, endstops must be enabled during SD printing.
|
||||
// With ENDSTOPS_ONLY_FOR_HOMING you must send "M120" to enable endstops.
|
||||
//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
|
||||
|
||||
#endif // SDSUPPORT
|
||||
|
||||
// for dogm lcd displays you can choose some additional fonts:
|
||||
#if ENABLED(DOGLCD)
|
||||
// save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
|
||||
// we don't have a big font for Cyrillic, Kana
|
||||
//#define USE_BIG_EDIT_FONT
|
||||
|
||||
// If you have spare 2300Byte of progmem and want to use a
|
||||
// smaller font on the Info-screen uncomment the next line.
|
||||
//#define USE_SMALL_INFOFONT
|
||||
#endif // DOGLCD
|
||||
|
||||
// @section safety
|
||||
|
||||
// The hardware watchdog should reset the microcontroller disabling all outputs,
|
||||
// in case the firmware gets stuck and doesn't do temperature regulation.
|
||||
#define USE_WATCHDOG
|
||||
|
||||
#if ENABLED(USE_WATCHDOG)
|
||||
// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
|
||||
// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
|
||||
// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
|
||||
//#define WATCHDOG_RESET_MANUAL
|
||||
#endif
|
||||
|
||||
// @section lcd
|
||||
|
||||
// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
|
||||
// it can e.g. be used to change z-positions in the print startup phase in real-time
|
||||
// does not respect endstops!
|
||||
//#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||
//not implemented for deltabots!
|
||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||
#endif
|
||||
|
||||
// @section extruder
|
||||
|
||||
// extruder advance constant (s2/mm3)
|
||||
//
|
||||
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
|
||||
//
|
||||
// Hooke's law says: force = k * distance
|
||||
// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
|
||||
// so: v ^ 2 is proportional to number of steps we advance the extruder
|
||||
//#define ADVANCE
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
#define EXTRUDER_ADVANCE_K .0
|
||||
#define D_FILAMENT 2.85
|
||||
#endif
|
||||
|
||||
// Implementation of a linear pressure control
|
||||
// Assumption: advance = k * (delta velocity)
|
||||
// K=0 means advance disabled. A good value for a gregs wade extruder will be around K=75
|
||||
//#define LIN_ADVANCE
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
#define LIN_ADVANCE_K 75
|
||||
#endif
|
||||
|
||||
// @section leveling
|
||||
|
||||
// Default mesh area is an area with an inset margin on the print area.
|
||||
// Below are the macros that are used to define the borders for the mesh area,
|
||||
// made available here for specialized needs, ie dual extruder setup.
|
||||
#if ENABLED(MESH_BED_LEVELING)
|
||||
#define MESH_MIN_X (X_MIN_POS + MESH_INSET)
|
||||
#define MESH_MAX_X (X_MAX_POS - (MESH_INSET))
|
||||
#define MESH_MIN_Y (Y_MIN_POS + MESH_INSET)
|
||||
#define MESH_MAX_Y (Y_MAX_POS - (MESH_INSET))
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
|
||||
// Arc interpretation settings:
|
||||
#define ARC_SUPPORT // Disabling this saves ~2738 bytes
|
||||
#define MM_PER_ARC_SEGMENT 1
|
||||
#define N_ARC_CORRECTION 25
|
||||
|
||||
// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
|
||||
//#define BEZIER_CURVE_SUPPORT
|
||||
|
||||
const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement
|
||||
|
||||
// @section temperature
|
||||
|
||||
// Control heater 0 and heater 1 in parallel.
|
||||
//#define HEATERS_PARALLEL
|
||||
|
||||
//===========================================================================
|
||||
//================================= Buffers =================================
|
||||
//===========================================================================
|
||||
|
||||
// @section hidden
|
||||
|
||||
// The number of linear motions that can be in the plan at any give time.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
|
||||
#if ENABLED(SDSUPPORT)
|
||||
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
#else
|
||||
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
#endif
|
||||
|
||||
// @section serial
|
||||
|
||||
// The ASCII buffer for serial input
|
||||
#define MAX_CMD_SIZE 96
|
||||
#define BUFSIZE 26
|
||||
|
||||
// Bad Serial-connections can miss a received command by sending an 'ok'
|
||||
// Therefore some clients abort after 30 seconds in a timeout.
|
||||
// Some other clients start sending commands while receiving a 'wait'.
|
||||
// This "wait" is only sent when the buffer is empty. 1 second is a good value here.
|
||||
//#define NO_TIMEOUTS 1000 // Milliseconds
|
||||
|
||||
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
|
||||
//#define ADVANCED_OK
|
||||
|
||||
// @section fwretract
|
||||
|
||||
// Firmware based and LCD controlled retract
|
||||
// M207 and M208 can be used to define parameters for the retraction.
|
||||
// The retraction can be called by the slicer using G10 and G11
|
||||
// until then, intended retractions can be detected by moves that only extrude and the direction.
|
||||
// the moves are than replaced by the firmware controlled ones.
|
||||
|
||||
//#define FWRETRACT //ONLY PARTIALLY TESTED
|
||||
#if ENABLED(FWRETRACT)
|
||||
#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
|
||||
#define RETRACT_LENGTH 3 //default retract length (positive mm)
|
||||
#define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
|
||||
#define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
|
||||
#define RETRACT_ZLIFT 0 //default retract Z-lift
|
||||
#define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
|
||||
#define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change)
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
#define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 100 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 100 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 20 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 5 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 600 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 600 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 100 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
* enable this section if you have TMC26X motor drivers.
|
||||
* you need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
******************************************************************************/
|
||||
|
||||
// @section tmc
|
||||
|
||||
//#define HAVE_TMCDRIVER
|
||||
#if ENABLED(HAVE_TMCDRIVER)
|
||||
|
||||
//#define X_IS_TMC
|
||||
#define X_MAX_CURRENT 1000 //in mA
|
||||
#define X_SENSE_RESISTOR 91 //in mOhms
|
||||
#define X_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define X2_IS_TMC
|
||||
#define X2_MAX_CURRENT 1000 //in mA
|
||||
#define X2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define Y_IS_TMC
|
||||
#define Y_MAX_CURRENT 1000 //in mA
|
||||
#define Y_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define Y2_IS_TMC
|
||||
#define Y2_MAX_CURRENT 1000 //in mA
|
||||
#define Y2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define Z_IS_TMC
|
||||
#define Z_MAX_CURRENT 1000 //in mA
|
||||
#define Z_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define Z2_IS_TMC
|
||||
#define Z2_MAX_CURRENT 1000 //in mA
|
||||
#define Z2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define E0_IS_TMC
|
||||
#define E0_MAX_CURRENT 1000 //in mA
|
||||
#define E0_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define E1_IS_TMC
|
||||
#define E1_MAX_CURRENT 1000 //in mA
|
||||
#define E1_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define E2_IS_TMC
|
||||
#define E2_MAX_CURRENT 1000 //in mA
|
||||
#define E2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define E3_IS_TMC
|
||||
#define E3_MAX_CURRENT 1000 //in mA
|
||||
#define E3_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
* enable this section if you have L6470 motor drivers.
|
||||
* you need to import the L6470 library into the Arduino IDE for this
|
||||
******************************************************************************/
|
||||
|
||||
// @section l6470
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
#define X_MICROSTEPS 16 //number of microsteps
|
||||
#define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define X2_IS_L6470
|
||||
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
#define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define Y_IS_L6470
|
||||
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
#define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define Y2_IS_L6470
|
||||
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
#define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define Z_IS_L6470
|
||||
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
#define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define Z2_IS_L6470
|
||||
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
#define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define E0_IS_L6470
|
||||
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
#define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define E1_IS_L6470
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
#define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define E2_IS_L6470
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
#define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define E3_IS_L6470
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
#define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
#endif
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
*
|
||||
* This feature is an EXPERIMENTAL feature so it shall not be used on production
|
||||
* machines. Enabling this will allow you to send and receive I2C data from slave
|
||||
* devices on the bus.
|
||||
*
|
||||
* ; Example #1
|
||||
* ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
|
||||
* ; It uses multiple M155 commands with one B<base 10> arg
|
||||
* M155 A99 ; Target slave address
|
||||
* M155 B77 ; M
|
||||
* M155 B97 ; a
|
||||
* M155 B114 ; r
|
||||
* M155 B108 ; l
|
||||
* M155 B105 ; i
|
||||
* M155 B110 ; n
|
||||
* M155 S1 ; Send the current buffer
|
||||
*
|
||||
* ; Example #2
|
||||
* ; Request 6 bytes from slave device with address 0x63 (99)
|
||||
* M156 A99 B5
|
||||
*
|
||||
* ; Example #3
|
||||
* ; Example serial output of a M156 request
|
||||
* echo:i2c-reply: from:99 bytes:5 data:hello
|
||||
*/
|
||||
|
||||
// @section i2cbus
|
||||
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
||||
#endif //CONFIGURATION_ADV_H
|
||||
1216
Marlin/example_configurations/K8400/Dual Heads/Configuration.h
Normal file
1216
Marlin/example_configurations/K8400/Dual Heads/Configuration.h
Normal file
|
|
@ -0,0 +1,1216 @@
|
|||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Configuration.h
|
||||
*
|
||||
* Basic settings such as:
|
||||
*
|
||||
* - Type of electronics
|
||||
* - Type of temperature sensor
|
||||
* - Printer geometry
|
||||
* - Endstop configuration
|
||||
* - LCD controller
|
||||
* - Extra features
|
||||
*
|
||||
* Advanced settings can be found in Configuration_adv.h
|
||||
*
|
||||
*/
|
||||
#ifndef CONFIGURATION_H
|
||||
#define CONFIGURATION_H
|
||||
|
||||
/**
|
||||
*
|
||||
* ***********************************
|
||||
* ** ATTENTION TO ALL DEVELOPERS **
|
||||
* ***********************************
|
||||
*
|
||||
* You must increment this version number for every significant change such as,
|
||||
* but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
|
||||
*
|
||||
* Note: Update also Version.h !
|
||||
*/
|
||||
#define CONFIGURATION_H_VERSION 010100
|
||||
|
||||
#include "boards.h"
|
||||
#include "macros.h"
|
||||
|
||||
//===========================================================================
|
||||
//============================= Getting Started =============================
|
||||
//===========================================================================
|
||||
|
||||
/**
|
||||
* Here are some standard links for getting your machine calibrated:
|
||||
*
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://youtu.be/wAL9d7FgInk
|
||||
* http://calculator.josefprusa.cz
|
||||
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||||
* http://www.thingiverse.com/thing:5573
|
||||
* https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
|
||||
* http://www.thingiverse.com/thing:298812
|
||||
*/
|
||||
|
||||
//===========================================================================
|
||||
//============================= DELTA Printer ===============================
|
||||
//===========================================================================
|
||||
// For a Delta printer replace the configuration files with the files in the
|
||||
// example_configurations/delta directory.
|
||||
//
|
||||
|
||||
//===========================================================================
|
||||
//============================= SCARA Printer ===============================
|
||||
//===========================================================================
|
||||
// For a Scara printer replace the configuration files with the files in the
|
||||
// example_configurations/SCARA directory.
|
||||
//
|
||||
|
||||
// @section info
|
||||
|
||||
#if ENABLED(USE_AUTOMATIC_VERSIONING)
|
||||
#include "_Version.h"
|
||||
#else
|
||||
#include "Version.h"
|
||||
#endif
|
||||
|
||||
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
||||
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
|
||||
// build by the user have been successfully uploaded into firmware.
|
||||
#define STRING_CONFIG_H_AUTHOR "(Anthony Birkett, default config)" // Who made the changes.
|
||||
#define SHOW_BOOTSCREEN
|
||||
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
|
||||
//#define STRING_SPLASH_LINE2 STRING_DISTRIBUTION_DATE // will be shown during bootup in line 2
|
||||
|
||||
// @section machine
|
||||
|
||||
// SERIAL_PORT selects which serial port should be used for communication with the host.
|
||||
// This allows the connection of wireless adapters (for instance) to non-default port pins.
|
||||
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
|
||||
// :[0,1,2,3,4,5,6,7]
|
||||
#define SERIAL_PORT 0
|
||||
|
||||
// This determines the communication speed of the printer
|
||||
// :[2400,9600,19200,38400,57600,115200,250000]
|
||||
#define BAUDRATE 250000
|
||||
|
||||
// Enable the Bluetooth serial interface on AT90USB devices
|
||||
//#define BLUETOOTH
|
||||
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_K8400
|
||||
#endif
|
||||
|
||||
// Optional custom name for your RepStrap or other custom machine
|
||||
// Displayed in the LCD "Ready" message
|
||||
//#define CUSTOM_MACHINE_NAME "3D Printer"
|
||||
|
||||
// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1,2,3,4]
|
||||
#define EXTRUDERS 2
|
||||
|
||||
// For Cyclops or any "multi-extruder" that shares a single nozzle.
|
||||
//#define SINGLENOZZLE
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||
// For the other hotends it is their distance from the extruder 0 hotend.
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
//// The following define selects which power supply you have. Please choose the one that matches your setup
|
||||
// 1 = ATX
|
||||
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
|
||||
// :{1:'ATX',2:'X-Box 360'}
|
||||
|
||||
#define POWER_SUPPLY 1
|
||||
|
||||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
//#define PS_DEFAULT_OFF
|
||||
|
||||
// @section temperature
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Settings ============================
|
||||
//===========================================================================
|
||||
//
|
||||
//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
|
||||
//
|
||||
//// Temperature sensor settings:
|
||||
// -3 is thermocouple with MAX31855 (only for sensor 0)
|
||||
// -2 is thermocouple with MAX6675 (only for sensor 0)
|
||||
// -1 is thermocouple with AD595
|
||||
// 0 is not used
|
||||
// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
|
||||
// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
|
||||
// 3 is Mendel-parts thermistor (4.7k pullup)
|
||||
// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
|
||||
// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
|
||||
// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
|
||||
// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
|
||||
// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
|
||||
// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
|
||||
// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
|
||||
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
|
||||
// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
|
||||
// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
|
||||
// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
|
||||
// 20 is the PT100 circuit found in the Ultimainboard V2.x
|
||||
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
|
||||
// 70 is the 100K thermistor found in the bq Hephestos 2
|
||||
//
|
||||
// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
|
||||
// (but gives greater accuracy and more stable PID)
|
||||
// 51 is 100k thermistor - EPCOS (1k pullup)
|
||||
// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
|
||||
// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
|
||||
//
|
||||
// 1047 is Pt1000 with 4k7 pullup
|
||||
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
// 147 is Pt100 with 4k7 pullup
|
||||
// 110 is Pt100 with 1k pullup (non standard)
|
||||
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
//#define DUMMY_THERMISTOR_998_VALUE 25
|
||||
//#define DUMMY_THERMISTOR_999_VALUE 100
|
||||
// :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-3': "Thermocouple + MAX31855 (only for sensor 0)", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" }
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 5
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
#define TEMP_SENSOR_BED 0
|
||||
|
||||
// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
|
||||
//#define TEMP_SENSOR_1_AS_REDUNDANT
|
||||
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
|
||||
|
||||
// Extruder temperature must be close to target for this long before M109 returns success
|
||||
#define TEMP_RESIDENCY_TIME 2 // (seconds)
|
||||
#define TEMP_HYSTERESIS 5 // (degC) range of +/- temperatures considered "close" to the target one
|
||||
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
|
||||
|
||||
// Bed temperature must be close to target for this long before M190 returns success
|
||||
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds)
|
||||
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
|
||||
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
|
||||
|
||||
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
|
||||
// to check that the wiring to the thermistor is not broken.
|
||||
// Otherwise this would lead to the heater being powered on all the time.
|
||||
#define HEATER_0_MINTEMP 5
|
||||
#define HEATER_1_MINTEMP 5
|
||||
#define HEATER_2_MINTEMP 5
|
||||
#define HEATER_3_MINTEMP 5
|
||||
#define BED_MINTEMP 5
|
||||
|
||||
// When temperature exceeds max temp, your heater will be switched off.
|
||||
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
|
||||
// You should use MINTEMP for thermistor short/failure protection.
|
||||
#define HEATER_0_MAXTEMP 275
|
||||
#define HEATER_1_MAXTEMP 275
|
||||
#define HEATER_2_MAXTEMP 275
|
||||
#define HEATER_3_MAXTEMP 275
|
||||
#define BED_MAXTEMP 150
|
||||
|
||||
// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
|
||||
//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R
|
||||
//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID Settings ================================
|
||||
//===========================================================================
|
||||
// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
|
||||
|
||||
// Comment the following line to disable PID and enable bang-bang.
|
||||
#define PIDTEMP
|
||||
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
||||
#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
|
||||
//#define PID_DEBUG // Sends debug data to the serial port.
|
||||
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
//#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
|
||||
#define K1 0.95 //smoothing factor within the PID
|
||||
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
// Ultimaker
|
||||
//#define DEFAULT_Kp 22.2
|
||||
//#define DEFAULT_Ki 1.08
|
||||
//#define DEFAULT_Kd 114
|
||||
|
||||
// MakerGear
|
||||
//#define DEFAULT_Kp 7.0
|
||||
//#define DEFAULT_Ki 0.1
|
||||
//#define DEFAULT_Kd 12
|
||||
|
||||
// Mendel Parts V9 on 12V
|
||||
#define DEFAULT_Kp 63.0
|
||||
#define DEFAULT_Ki 2.25
|
||||
#define DEFAULT_Kd 440
|
||||
|
||||
#endif // PIDTEMP
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||||
//
|
||||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
//#define PID_BED_DEBUG // Sends debug data to the serial port.
|
||||
|
||||
#define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
#define DEFAULT_bedKp 10.00
|
||||
#define DEFAULT_bedKi .023
|
||||
#define DEFAULT_bedKd 305.4
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from pidautotune
|
||||
//#define DEFAULT_bedKp 97.1
|
||||
//#define DEFAULT_bedKi 1.41
|
||||
//#define DEFAULT_bedKd 1675.16
|
||||
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#endif // PIDTEMPBED
|
||||
|
||||
// @section extruder
|
||||
|
||||
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
||||
//can be software-disabled for whatever purposes by
|
||||
#define PREVENT_DANGEROUS_EXTRUDE
|
||||
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
|
||||
#define PREVENT_LENGTHY_EXTRUDE
|
||||
|
||||
#define EXTRUDE_MINTEMP 160
|
||||
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
||||
|
||||
//===========================================================================
|
||||
//======================== Thermal Runaway Protection =======================
|
||||
//===========================================================================
|
||||
|
||||
/**
|
||||
* Thermal Protection protects your printer from damage and fire if a
|
||||
* thermistor falls out or temperature sensors fail in any way.
|
||||
*
|
||||
* The issue: If a thermistor falls out or a temperature sensor fails,
|
||||
* Marlin can no longer sense the actual temperature. Since a disconnected
|
||||
* thermistor reads as a low temperature, the firmware will keep the heater on.
|
||||
*
|
||||
* If you get "Thermal Runaway" or "Heating failed" errors the
|
||||
* details can be tuned in Configuration_adv.h
|
||||
*/
|
||||
|
||||
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
|
||||
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
|
||||
|
||||
//===========================================================================
|
||||
//============================= Mechanical Settings =========================
|
||||
//===========================================================================
|
||||
|
||||
// @section machine
|
||||
|
||||
// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
|
||||
//#define COREXY
|
||||
//#define COREXZ
|
||||
//#define COREYZ
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
//#define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
//===========================================================================
|
||||
//============================== Endstop Settings ===========================
|
||||
//===========================================================================
|
||||
|
||||
// @section homing
|
||||
|
||||
// Specify here all the endstop connectors that are connected to any endstop or probe.
|
||||
// Almost all printers will be using one per axis. Probes will use one or more of the
|
||||
// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
|
||||
#define USE_XMIN_PLUG
|
||||
#define USE_YMIN_PLUG
|
||||
#define USE_ZMIN_PLUG
|
||||
//#define USE_XMAX_PLUG
|
||||
//#define USE_YMAX_PLUG
|
||||
//#define USE_ZMAX_PLUG
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
#if DISABLED(ENDSTOPPULLUPS)
|
||||
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
||||
//#define ENDSTOPPULLUP_XMAX
|
||||
//#define ENDSTOPPULLUP_YMAX
|
||||
//#define ENDSTOPPULLUP_ZMAX
|
||||
//#define ENDSTOPPULLUP_XMIN
|
||||
//#define ENDSTOPPULLUP_YMIN
|
||||
//#define ENDSTOPPULLUP_ZMIN
|
||||
//#define ENDSTOPPULLUP_ZMIN_PROBE
|
||||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
|
||||
//===========================================================================
|
||||
//============================= Z Probe Options =============================
|
||||
//===========================================================================
|
||||
|
||||
//
|
||||
// Probe Type
|
||||
// Probes are sensors/switches that are activated / deactivated before/after use.
|
||||
//
|
||||
// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
|
||||
// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below.
|
||||
//
|
||||
// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500.
|
||||
//
|
||||
|
||||
// A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
|
||||
// For example an inductive probe, or a setup that uses the nozzle to probe.
|
||||
// An inductive probe must be deactivated to go below
|
||||
// its trigger-point if hardware endstops are active.
|
||||
//#define FIX_MOUNTED_PROBE
|
||||
|
||||
// Z Servo Probe, such as an endstop switch on a rotating arm.
|
||||
//#define Z_ENDSTOP_SERVO_NR 0
|
||||
//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
|
||||
|
||||
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||
//#define Z_PROBE_SLED
|
||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||
|
||||
// Z Probe to nozzle (X,Y) offset, relative to (0, 0).
|
||||
// X and Y offsets must be integers.
|
||||
//
|
||||
// In the following example the X and Y offsets are both positive:
|
||||
// #define X_PROBE_OFFSET_FROM_EXTRUDER 10
|
||||
// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
|
||||
//
|
||||
// +-- BACK ---+
|
||||
// | |
|
||||
// L | (+) P | R <-- probe (20,20)
|
||||
// E | | I
|
||||
// F | (-) N (+) | G <-- nozzle (10,10)
|
||||
// T | | H
|
||||
// | (-) | T
|
||||
// | |
|
||||
// O-- FRONT --+
|
||||
// (0,0)
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
|
||||
|
||||
// X and Y axis travel speed (mm/m) between probes
|
||||
#define XY_PROBE_SPEED 8000
|
||||
|
||||
//
|
||||
// Allen Key Probe is defined in the Delta example configurations.
|
||||
//
|
||||
|
||||
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
|
||||
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
|
||||
//
|
||||
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
|
||||
//
|
||||
// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
|
||||
// Example: To park the head outside the bed area when homing with G28.
|
||||
//
|
||||
// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
|
||||
//
|
||||
// For a servo-based Z probe, you must set up servo support below, including
|
||||
// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
|
||||
//
|
||||
// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
|
||||
// - Use 5V for powered (usu. inductive) sensors.
|
||||
// - Otherwise connect:
|
||||
// - normally-closed switches to GND and D32.
|
||||
// - normally-open switches to 5V and D32.
|
||||
//
|
||||
// Normally-closed switches are advised and are the default.
|
||||
//
|
||||
// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
|
||||
// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
|
||||
// default pin for all RAMPS-based boards. Some other boards map differently.
|
||||
// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
|
||||
//
|
||||
// WARNING:
|
||||
// Setting the wrong pin may have unexpected and potentially disastrous consequences.
|
||||
// Use with caution and do your homework.
|
||||
//
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
|
||||
// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
|
||||
// The Z_MIN_PIN will then be used for both Z-homing and probing.
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
// To use a probe you must enable one of the two options above!
|
||||
|
||||
// This option disables the use of the Z_MIN_PROBE_PIN
|
||||
// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
|
||||
// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
|
||||
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
|
||||
//#define DISABLE_Z_MIN_PROBE_ENDSTOP
|
||||
|
||||
// Enable Z Probe Repeatability test to see how accurate your probe is
|
||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
|
||||
//
|
||||
// Probe Raise options provide clearance for the probe to deploy, stow, and travel.
|
||||
//
|
||||
#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
|
||||
#define Z_RAISE_BETWEEN_PROBINGS 5 // Raise between probing points.
|
||||
|
||||
//
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
//
|
||||
#define Z_PROBE_OFFSET_RANGE_MIN -20
|
||||
#define Z_PROBE_OFFSET_RANGE_MAX 20
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
// :{0:'Low',1:'High'}
|
||||
#define X_ENABLE_ON 0
|
||||
#define Y_ENABLE_ON 0
|
||||
#define Z_ENABLE_ON 0
|
||||
#define E_ENABLE_ON 0 // For all extruders
|
||||
|
||||
// Disables axis stepper immediately when it's not being used.
|
||||
// WARNING: When motors turn off there is a chance of losing position accuracy!
|
||||
#define DISABLE_X false
|
||||
#define DISABLE_Y false
|
||||
#define DISABLE_Z false
|
||||
// Warn on display about possibly reduced accuracy
|
||||
//#define DISABLE_REDUCED_ACCURACY_WARNING
|
||||
|
||||
// @section extruder
|
||||
|
||||
#define DISABLE_E false // For all extruders
|
||||
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
||||
|
||||
// @section machine
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Z_DIR true
|
||||
|
||||
// @section extruder
|
||||
|
||||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
#define INVERT_E0_DIR false
|
||||
#define INVERT_E1_DIR true
|
||||
#define INVERT_E2_DIR false
|
||||
#define INVERT_E3_DIR false
|
||||
|
||||
// @section homing
|
||||
//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// ENDSTOP SETTINGS:
|
||||
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
||||
// :[-1,1]
|
||||
#define X_HOME_DIR -1
|
||||
#define Y_HOME_DIR -1
|
||||
#define Z_HOME_DIR -1
|
||||
|
||||
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
|
||||
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
|
||||
// @section machine
|
||||
|
||||
// Travel limits after homing (units are in mm)
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MIN_POS 20
|
||||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS 200
|
||||
#define Y_MAX_POS 200
|
||||
#define Z_MAX_POS 190
|
||||
|
||||
//===========================================================================
|
||||
//========================= Filament Runout Sensor ==========================
|
||||
//===========================================================================
|
||||
//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
|
||||
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
|
||||
// It is assumed that when logic high = filament available
|
||||
// when logic low = filament ran out
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
const bool FIL_RUNOUT_INVERTING = false; // set to true to invert the logic of the sensor.
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//============================ Mesh Bed Leveling ============================
|
||||
//===========================================================================
|
||||
|
||||
//#define MESH_BED_LEVELING // Enable mesh bed leveling.
|
||||
|
||||
#if ENABLED(MESH_BED_LEVELING)
|
||||
#define MESH_INSET 10 // Mesh inset margin on print area
|
||||
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define MESH_NUM_Y_POINTS 3
|
||||
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0.
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0]
|
||||
|
||||
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.
|
||||
|
||||
#if ENABLED(MANUAL_BED_LEVELING)
|
||||
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
|
||||
#endif // MANUAL_BED_LEVELING
|
||||
|
||||
#endif // MESH_BED_LEVELING
|
||||
|
||||
//===========================================================================
|
||||
//============================ Bed Auto Leveling ============================
|
||||
//===========================================================================
|
||||
|
||||
// @section bedlevel
|
||||
|
||||
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
|
||||
//#define DEBUG_LEVELING_FEATURE
|
||||
|
||||
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
|
||||
|
||||
// There are 2 different ways to specify probing locations:
|
||||
//
|
||||
// - "grid" mode
|
||||
// Probe several points in a rectangular grid.
|
||||
// You specify the rectangle and the density of sample points.
|
||||
// This mode is preferred because there are more measurements.
|
||||
//
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't collinear)
|
||||
// You specify the XY coordinates of all 3 points.
|
||||
|
||||
// Enable this to sample the bed in a grid (least squares solution).
|
||||
// Note: this feature generates 10KB extra code size.
|
||||
#define AUTO_BED_LEVELING_GRID
|
||||
|
||||
#if ENABLED(AUTO_BED_LEVELING_GRID)
|
||||
|
||||
#define LEFT_PROBE_BED_POSITION 15
|
||||
#define RIGHT_PROBE_BED_POSITION 170
|
||||
#define FRONT_PROBE_BED_POSITION 20
|
||||
#define BACK_PROBE_BED_POSITION 170
|
||||
|
||||
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
|
||||
|
||||
// Set the number of grid points per dimension.
|
||||
// You probably don't need more than 3 (squared=9).
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
// Arbitrary points to probe.
|
||||
// A simple cross-product is used to estimate the plane of the bed.
|
||||
#define ABL_PROBE_PT_1_X 15
|
||||
#define ABL_PROBE_PT_1_Y 180
|
||||
#define ABL_PROBE_PT_2_X 15
|
||||
#define ABL_PROBE_PT_2_Y 20
|
||||
#define ABL_PROBE_PT_3_X 170
|
||||
#define ABL_PROBE_PT_3_Y 20
|
||||
|
||||
#endif // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
|
||||
// Useful to retract a deployable Z probe.
|
||||
|
||||
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
|
||||
// it is highly recommended you also enable Z_SAFE_HOMING below!
|
||||
|
||||
#endif // AUTO_BED_LEVELING_FEATURE
|
||||
|
||||
|
||||
// @section homing
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
|
||||
#endif
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
// With this feature enabled:
|
||||
//
|
||||
// - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
|
||||
// - If stepper drivers time out, it will need X and Y homing again before Z homing.
|
||||
// - Position the Z probe in a defined XY point before Z Homing when homing all axes (G28).
|
||||
// - Prevent Z homing when the Z probe is outside bed area.
|
||||
//#define Z_SAFE_HOMING
|
||||
|
||||
#if ENABLED(Z_SAFE_HOMING)
|
||||
#define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).
|
||||
#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
|
||||
#endif
|
||||
|
||||
|
||||
// @section motion
|
||||
|
||||
/**
|
||||
* MOVEMENT SETTINGS
|
||||
*/
|
||||
|
||||
#define HOMING_FEEDRATE {50*60, 50*60, 8*60, 0} // set the homing speeds (mm/min)
|
||||
|
||||
// default settings
|
||||
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {134.74,134.74,4266.66,148.7} // default steps per unit for Ultimaker
|
||||
#define DEFAULT_MAX_FEEDRATE {160, 160, 10, 10000} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 6000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 6000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||
|
||||
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||
#define DEFAULT_XYJERK 10.0 // (mm/sec)
|
||||
#define DEFAULT_ZJERK 0.5 // (mm/sec)
|
||||
#define DEFAULT_EJERK 20.0 // (mm/sec)
|
||||
|
||||
|
||||
//=============================================================================
|
||||
//============================= Additional Features ===========================
|
||||
//=============================================================================
|
||||
|
||||
// @section extras
|
||||
|
||||
//
|
||||
// EEPROM
|
||||
//
|
||||
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
|
||||
// M500 - stores parameters in EEPROM
|
||||
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
//define this to enable EEPROM support
|
||||
#define EEPROM_SETTINGS
|
||||
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
#define EEPROM_CHITCHAT // Please keep turned on if you can.
|
||||
#endif
|
||||
|
||||
//
|
||||
// Host Keepalive
|
||||
//
|
||||
// When enabled Marlin will send a busy status message to the host
|
||||
// every couple of seconds when it can't accept commands.
|
||||
//
|
||||
#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
|
||||
#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
|
||||
|
||||
//
|
||||
// M100 Free Memory Watcher
|
||||
//
|
||||
//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
|
||||
|
||||
//
|
||||
// G20/G21 Inch mode support
|
||||
//
|
||||
//#define INCH_MODE_SUPPORT
|
||||
|
||||
//
|
||||
// M149 Set temperature units support
|
||||
//
|
||||
//#define TEMPERATURE_UNITS_SUPPORT
|
||||
|
||||
// @section temperature
|
||||
|
||||
// Preheat Constants
|
||||
#define PLA_PREHEAT_HOTEND_TEMP 210
|
||||
#define PLA_PREHEAT_HPB_TEMP 0
|
||||
#define PLA_PREHEAT_FAN_SPEED 165 // Insert Value between 0 and 255
|
||||
|
||||
#define ABS_PREHEAT_HOTEND_TEMP 245
|
||||
#define ABS_PREHEAT_HPB_TEMP 0
|
||||
#define ABS_PREHEAT_FAN_SPEED 165 // Insert Value between 0 and 255
|
||||
|
||||
//
|
||||
// Print job timer
|
||||
//
|
||||
// Enable this option to automatically start and stop the
|
||||
// print job timer when M104 and M109 commands are received.
|
||||
//
|
||||
// In all cases the timer can be started and stopped using
|
||||
// the following commands:
|
||||
//
|
||||
// - M75 - Start the print job timer
|
||||
// - M76 - Pause the print job timer
|
||||
// - M77 - Stop the print job timer
|
||||
#define PRINTJOB_TIMER_AUTOSTART
|
||||
|
||||
//
|
||||
// Print Counter
|
||||
//
|
||||
// When enabled Marlin will keep track of some print statistical data such as:
|
||||
// - Total print jobs
|
||||
// - Total successful print jobs
|
||||
// - Total failed print jobs
|
||||
// - Total time printing
|
||||
//
|
||||
// This information can be viewed by the M78 command.
|
||||
//#define PRINTCOUNTER
|
||||
|
||||
//=============================================================================
|
||||
//============================= LCD and SD support ============================
|
||||
//=============================================================================
|
||||
|
||||
// @section lcd
|
||||
|
||||
//
|
||||
// LCD LANGUAGE
|
||||
//
|
||||
// Here you may choose the language used by Marlin on the LCD menus, the following
|
||||
// list of languages are available:
|
||||
// en, an, bg, ca, cn, cz, de, es, eu, fi, fr, gl, hr, it, kana,
|
||||
// kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, test
|
||||
//
|
||||
// :{'en':'English','an':'Aragonese','bg':'Bulgarian','ca':'Catalan','cn':'Chinese','cz':'Czech','de':'German','es':'Spanish','eu':'Basque-Euskera','fi':'Finnish','fr':'French','gl':'Galician','hr':'Croatian','it':'Italian','kana':'Japanese','kana_utf8':'Japanese (UTF8)','nl':'Dutch','pl':'Polish','pt':'Portuguese','pt-br':'Portuguese (Brazilian)','pt-br_utf8':'Portuguese (Brazilian UTF8)','pt_utf8':'Portuguese (UTF8)','ru':'Russian','test':'TEST'}
|
||||
//
|
||||
#define LCD_LANGUAGE en
|
||||
|
||||
//
|
||||
// LCD Character Set
|
||||
//
|
||||
// Note: This option is NOT applicable to Graphical Displays.
|
||||
//
|
||||
// All character-based LCD's provide ASCII plus one of these
|
||||
// language extensions:
|
||||
//
|
||||
// - JAPANESE ... the most common
|
||||
// - WESTERN ... with more accented characters
|
||||
// - CYRILLIC ... for the Russian language
|
||||
//
|
||||
// To determine the language extension installed on your controller:
|
||||
//
|
||||
// - Compile and upload with LCD_LANGUAGE set to 'test'
|
||||
// - Click the controller to view the LCD menu
|
||||
// - The LCD will display Japanese, Western, or Cyrillic text
|
||||
//
|
||||
// See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
|
||||
//
|
||||
// :['JAPANESE','WESTERN','CYRILLIC']
|
||||
//
|
||||
#define DISPLAY_CHARSET_HD44780 JAPANESE
|
||||
|
||||
//
|
||||
// LCD TYPE
|
||||
//
|
||||
// You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2,
|
||||
// 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels
|
||||
// (ST7565R family). (This option will be set automatically for certain displays.)
|
||||
//
|
||||
// IMPORTANT NOTE: The U8glib library is required for Full Graphic Display!
|
||||
// https://github.com/olikraus/U8glib_Arduino
|
||||
//
|
||||
#define ULTRA_LCD // Character based
|
||||
//#define DOGLCD // Full graphics display
|
||||
|
||||
//
|
||||
// SD CARD
|
||||
//
|
||||
// SD Card support is disabled by default. If your controller has an SD slot,
|
||||
// you must uncomment the following option or it won't work.
|
||||
//
|
||||
#define SDSUPPORT
|
||||
|
||||
//
|
||||
// SD CARD: SPI SPEED
|
||||
//
|
||||
// Uncomment ONE of the following items to use a slower SPI transfer
|
||||
// speed. This is usually required if you're getting volume init errors.
|
||||
//
|
||||
//#define SPI_SPEED SPI_HALF_SPEED
|
||||
//#define SPI_SPEED SPI_QUARTER_SPEED
|
||||
//#define SPI_SPEED SPI_EIGHTH_SPEED
|
||||
|
||||
//
|
||||
// SD CARD: ENABLE CRC
|
||||
//
|
||||
// Use CRC checks and retries on the SD communication.
|
||||
//
|
||||
//#define SD_CHECK_AND_RETRY
|
||||
|
||||
//
|
||||
// ENCODER SETTINGS
|
||||
//
|
||||
// This option overrides the default number of encoder pulses needed to
|
||||
// produce one step. Should be increased for high-resolution encoders.
|
||||
//
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
|
||||
//
|
||||
// Use this option to override the number of step signals required to
|
||||
// move between next/prev menu items.
|
||||
//
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
|
||||
/**
|
||||
* Encoder Direction Options
|
||||
*
|
||||
* Test your encoder's behavior first with both options disabled.
|
||||
*
|
||||
* Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
|
||||
* Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
|
||||
* Reversed Value Editing only? Enable BOTH options.
|
||||
*/
|
||||
|
||||
//
|
||||
// This option reverses the encoder direction everywhere
|
||||
//
|
||||
// Set this option if CLOCKWISE causes values to DECREASE
|
||||
//
|
||||
//#define REVERSE_ENCODER_DIRECTION
|
||||
|
||||
//
|
||||
// This option reverses the encoder direction for navigating LCD menus.
|
||||
//
|
||||
// If CLOCKWISE normally moves DOWN this makes it go UP.
|
||||
// If CLOCKWISE normally moves UP this makes it go DOWN.
|
||||
//
|
||||
#define REVERSE_MENU_DIRECTION
|
||||
|
||||
//
|
||||
// Individual Axis Homing
|
||||
//
|
||||
// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
|
||||
//
|
||||
//#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
|
||||
//
|
||||
// SPEAKER/BUZZER
|
||||
//
|
||||
// If you have a speaker that can produce tones, enable it here.
|
||||
// By default Marlin assumes you have a buzzer with a fixed frequency.
|
||||
//
|
||||
//#define SPEAKER
|
||||
|
||||
//
|
||||
// The duration and frequency for the UI feedback sound.
|
||||
// Set these to 0 to disable audio feedback in the LCD menus.
|
||||
//
|
||||
// Note: Test audio output with the G-Code:
|
||||
// M300 S<frequency Hz> P<duration ms>
|
||||
//
|
||||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000
|
||||
|
||||
//
|
||||
// CONTROLLER TYPE: Standard
|
||||
//
|
||||
// Marlin supports a wide variety of controllers.
|
||||
// Enable one of the following options to specify your controller.
|
||||
//
|
||||
|
||||
//
|
||||
// ULTIMAKER Controller.
|
||||
//
|
||||
#define ULTIMAKERCONTROLLER
|
||||
|
||||
//
|
||||
// ULTIPANEL as seen on Thingiverse.
|
||||
//
|
||||
//#define ULTIPANEL
|
||||
|
||||
//
|
||||
// Cartesio UI
|
||||
// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
|
||||
//
|
||||
//#define CARTESIO_UI
|
||||
|
||||
//
|
||||
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
|
||||
// http://reprap.org/wiki/PanelOne
|
||||
//
|
||||
//#define PANEL_ONE
|
||||
|
||||
//
|
||||
// MaKr3d Makr-Panel with graphic controller and SD support.
|
||||
// http://reprap.org/wiki/MaKr3d_MaKrPanel
|
||||
//
|
||||
//#define MAKRPANEL
|
||||
|
||||
//
|
||||
// Activate one of these if you have a Panucatt Devices
|
||||
// Viki 2.0 or mini Viki with Graphic LCD
|
||||
// http://panucatt.com
|
||||
//
|
||||
//#define VIKI2
|
||||
//#define miniVIKI
|
||||
|
||||
//
|
||||
// Adafruit ST7565 Full Graphic Controller.
|
||||
// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
|
||||
//
|
||||
//#define ELB_FULL_GRAPHIC_CONTROLLER
|
||||
|
||||
//
|
||||
// RepRapDiscount Smart Controller.
|
||||
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
|
||||
//
|
||||
// Note: Usually sold with a white PCB.
|
||||
//
|
||||
//#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||||
|
||||
//
|
||||
// GADGETS3D G3D LCD/SD Controller
|
||||
// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
|
||||
//
|
||||
// Note: Usually sold with a blue PCB.
|
||||
//
|
||||
//#define G3D_PANEL
|
||||
|
||||
//
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
// controller and SD support - http://reprap.org/wiki/Mini_panel
|
||||
//
|
||||
//#define MINIPANEL
|
||||
|
||||
//
|
||||
// RepRapWorld REPRAPWORLD_KEYPAD v1.1
|
||||
// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
|
||||
//
|
||||
// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
|
||||
// is pressed, a value of 10.0 means 10mm per click.
|
||||
//
|
||||
//#define REPRAPWORLD_KEYPAD
|
||||
//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
|
||||
|
||||
//
|
||||
// RigidBot Panel V1.0
|
||||
// http://www.inventapart.com/
|
||||
//
|
||||
//#define RIGIDBOT_PANEL
|
||||
|
||||
//
|
||||
// BQ LCD Smart Controller shipped by
|
||||
// default with the BQ Hephestos 2 and Witbox 2.
|
||||
//
|
||||
//#define BQ_LCD_SMART_CONTROLLER
|
||||
|
||||
//
|
||||
// CONTROLLER TYPE: I2C
|
||||
//
|
||||
// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
|
||||
// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
||||
//
|
||||
|
||||
//
|
||||
// Elefu RA Board Control Panel
|
||||
// http://www.elefu.com/index.php?route=product/product&product_id=53
|
||||
//
|
||||
//#define RA_CONTROL_PANEL
|
||||
|
||||
//
|
||||
// Sainsmart YW Robot (LCM1602) LCD Display
|
||||
//
|
||||
//#define LCD_I2C_SAINSMART_YWROBOT
|
||||
|
||||
//
|
||||
// Generic LCM1602 LCD adapter
|
||||
//
|
||||
//#define LCM1602
|
||||
|
||||
//
|
||||
// PANELOLU2 LCD with status LEDs,
|
||||
// separate encoder and click inputs.
|
||||
//
|
||||
// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
|
||||
// For more info: https://github.com/lincomatic/LiquidTWI2
|
||||
//
|
||||
// Note: The PANELOLU2 encoder click input can either be directly connected to
|
||||
// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
|
||||
//
|
||||
//#define LCD_I2C_PANELOLU2
|
||||
|
||||
//
|
||||
// Panucatt VIKI LCD with status LEDs,
|
||||
// integrated click & L/R/U/D buttons, separate encoder inputs.
|
||||
//
|
||||
//#define LCD_I2C_VIKI
|
||||
|
||||
//
|
||||
// SSD1306 OLED full graphics generic display
|
||||
//
|
||||
//#define U8GLIB_SSD1306
|
||||
|
||||
//
|
||||
// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
|
||||
//
|
||||
//#define SAV_3DGLCD
|
||||
#if ENABLED(SAV_3DGLCD)
|
||||
//#define U8GLIB_SSD1306
|
||||
#define U8GLIB_SH1106
|
||||
#endif
|
||||
|
||||
//
|
||||
// CONTROLLER TYPE: Shift register panels
|
||||
//
|
||||
// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
|
||||
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
|
||||
//
|
||||
//#define SAV_3DLCD
|
||||
|
||||
//=============================================================================
|
||||
//=============================== Extra Features ==============================
|
||||
//=============================================================================
|
||||
|
||||
// @section extras
|
||||
|
||||
// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||||
//#define FAST_PWM_FAN
|
||||
|
||||
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
|
||||
// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
|
||||
// is too low, you should also increment SOFT_PWM_SCALE.
|
||||
//#define FAN_SOFT_PWM
|
||||
|
||||
// Incrementing this by 1 will double the software PWM frequency,
|
||||
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
|
||||
// However, control resolution will be halved for each increment;
|
||||
// at zero value, there are 128 effective control positions.
|
||||
#define SOFT_PWM_SCALE 0
|
||||
|
||||
// Temperature status LEDs that display the hotend and bed temperature.
|
||||
// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
|
||||
// Otherwise the RED led is on. There is 1C hysteresis.
|
||||
//#define TEMP_STAT_LEDS
|
||||
|
||||
// M240 Triggers a camera by emulating a Canon RC-1 Remote
|
||||
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
||||
//#define PHOTOGRAPH_PIN 23
|
||||
|
||||
// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
|
||||
//#define SF_ARC_FIX
|
||||
|
||||
// Support for the BariCUDA Paste Extruder.
|
||||
//#define BARICUDA
|
||||
|
||||
//define BlinkM/CyzRgb Support
|
||||
//#define BLINKM
|
||||
|
||||
/*********************************************************************\
|
||||
* R/C SERVO support
|
||||
* Sponsored by TrinityLabs, Reworked by codexmas
|
||||
**********************************************************************/
|
||||
|
||||
// Number of servos
|
||||
//
|
||||
// If you select a configuration below, this will receive a default value and does not need to be set manually
|
||||
// set it manually if you have more servos than extruders and wish to manually control some
|
||||
// leaving it undefined or defining as 0 will disable the servo subsystem
|
||||
// If unsure, leave commented / disabled
|
||||
//
|
||||
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
|
||||
|
||||
// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
|
||||
// 300ms is a good value but you can try less delay.
|
||||
// If the servo can't reach the requested position, increase it.
|
||||
#define SERVO_DELAY 300
|
||||
|
||||
// Servo deactivation
|
||||
//
|
||||
// With this option servos are powered only during movement, then turned off to prevent jitter.
|
||||
//#define DEACTIVATE_SERVOS_AFTER_MOVE
|
||||
|
||||
/**********************************************************************\
|
||||
* Support for a filament diameter sensor
|
||||
* Also allows adjustment of diameter at print time (vs at slicing)
|
||||
* Single extruder only at this point (extruder 0)
|
||||
*
|
||||
* Motherboards
|
||||
* 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
|
||||
* 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
|
||||
* 301 - Rambo - uses Analog input 3
|
||||
* Note may require analog pins to be defined for different motherboards
|
||||
**********************************************************************/
|
||||
// Uncomment below to enable
|
||||
//#define FILAMENT_WIDTH_SENSOR
|
||||
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
|
||||
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||||
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
|
||||
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
|
||||
|
||||
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
|
||||
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
|
||||
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
|
||||
|
||||
//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec.
|
||||
//#define FILAMENT_LCD_DISPLAY
|
||||
#endif
|
||||
|
||||
#include "Configuration_adv.h"
|
||||
#include "thermistortables.h"
|
||||
|
||||
#endif //CONFIGURATION_H
|
||||
15
Marlin/example_configurations/K8400/README.md
Normal file
15
Marlin/example_configurations/K8400/README.md
Normal file
|
|
@ -0,0 +1,15 @@
|
|||
# Configuration for Velleman K8400 Vertex
|
||||
http://www.k8400.eu/
|
||||
|
||||
Configuration files for the K8400, ported upstream from the official Velleman firmware.
|
||||
Like it's predecessor, (K8200), the K8400 is a 3Drag clone. There are some minor differences, documented in pins_K8400.h.
|
||||
|
||||
Single and dual head configurations provided. Copy the correct Configuration.h and Configuration_adv.h to the /Marlin/ directory.
|
||||
|
||||
**NOTE: This configuration includes the community sourced feed rate fix. Use 100% feed rate in Repetier!**
|
||||
|
||||
For implementation and updated K8400 firmware, see https://github.com/birkett/Velleman-K8400-Firmware
|
||||
|
||||
### Original Sources
|
||||
Credit to Velleman for the original 1.0.x based code:<br />
|
||||
http://www.vertex3dprinter.eu/downloads/files/vertex/firmware/vertex-m1-v1.4-h2.zip
|
||||
|
|
@ -77,6 +77,8 @@
|
|||
#include "pins_3DRAG.h"
|
||||
#elif MB(K8200)
|
||||
#include "pins_K8200.h"
|
||||
#elif MB(K8400)
|
||||
#include "pins_K8400.h"
|
||||
#elif MB(TEENSYLU)
|
||||
#include "pins_TEENSYLU.h"
|
||||
#elif MB(RUMBA)
|
||||
|
|
|
|||
|
|
@ -21,7 +21,7 @@
|
|||
*/
|
||||
|
||||
/**
|
||||
* 3DRAG (and K8200) Arduino Mega with RAMPS v1.4 pin assignments
|
||||
* 3DRAG (and K8200 / K8400) Arduino Mega with RAMPS v1.4 pin assignments
|
||||
*/
|
||||
|
||||
#ifndef BOARD_NAME
|
||||
|
|
|
|||
52
Marlin/pins_K8400.h
Normal file
52
Marlin/pins_K8400.h
Normal file
|
|
@ -0,0 +1,52 @@
|
|||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Velleman K8400 (Vertex)
|
||||
* 3DRAG clone
|
||||
*
|
||||
* K8400 has some minor differences over a normal 3Drag:
|
||||
* - No X/Y max endstops
|
||||
* - Second extruder step pin has moved
|
||||
* - No power supply control
|
||||
* - Second heater has moved pin
|
||||
*/
|
||||
|
||||
#define BOARD_NAME "K8400"
|
||||
#define DEFAULT_MACHINE_NAME "Vertex"
|
||||
#define DEFAULT_SOURCE_CODE_URL "https://github.com/birkett/Vertex-K8400-Firmware"
|
||||
|
||||
#include "pins_3DRAG.h"
|
||||
|
||||
#undef X_MAX_PIN
|
||||
#define X_MAX_PIN -1
|
||||
#undef Y_MAX_PIN
|
||||
#define Y_MAX_PIN -1
|
||||
|
||||
#undef E1_STEP_PIN
|
||||
#define E1_STEP_PIN 32
|
||||
|
||||
#undef PS_ON_PIN
|
||||
#undef KILL_PIN
|
||||
|
||||
#undef HEATER_1_PIN
|
||||
#define HEATER_1_PIN 11
|
||||
|
|
@ -59,7 +59,7 @@
|
|||
#define CPU_ST7920_DELAY_1 DELAY_0_NOP
|
||||
#define CPU_ST7920_DELAY_2 DELAY_0_NOP
|
||||
#define CPU_ST7920_DELAY_3 DELAY_1_NOP
|
||||
#elif (MOTHERBOARD == BOARD_3DRAG) || (MOTHERBOARD == BOARD_K8200)
|
||||
#elif (MOTHERBOARD == BOARD_3DRAG) || (MOTHERBOARD == BOARD_K8200) || (MOTHERBOARD == BOARD_K8400)
|
||||
#define CPU_ST7920_DELAY_1 DELAY_0_NOP
|
||||
#define CPU_ST7920_DELAY_2 DELAY_3_NOP
|
||||
#define CPU_ST7920_DELAY_3 DELAY_0_NOP
|
||||
|
|
|
|||
Reference in a new issue