diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h index d40535a31..8ca00396f 100644 --- a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h +++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h @@ -620,7 +620,7 @@ * Use G29 repeatedly, adjusting the Z height at each point with movement commands * or (with LCD_BED_LEVELING) the LCD controller. */ -//#define PROBE_MANUALLY +#define PROBE_MANUALLY /** * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. @@ -768,7 +768,7 @@ //#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed -//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... +#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure you have this distance over your Z_MAX_POS in case. // Direction of endstops when homing; 1=MAX, -1=MIN @@ -871,9 +871,9 @@ */ //#define AUTO_BED_LEVELING_3POINT //#define AUTO_BED_LEVELING_LINEAR -//#define AUTO_BED_LEVELING_BILINEAR +#define AUTO_BED_LEVELING_BILINEAR //#define AUTO_BED_LEVELING_UBL -#define MESH_BED_LEVELING +//#define MESH_BED_LEVELING /** * Enable detailed logging of G28, G29, M48, etc. @@ -899,10 +899,10 @@ */ #define G26_MESH_VALIDATION // Enable G26 mesh validation #if ENABLED(G26_MESH_VALIDATION) - #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. - #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. - #define MESH_TEST_HOTEND_TEMP 205.0 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. - #define MESH_TEST_BED_TEMP 60.0 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205.0 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60.0 // (°C) Default bed temperature for the G26 Mesh Validation Tool. #endif #endif @@ -1113,8 +1113,8 @@ // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. // -#define EEPROM_SETTINGS // Enable for M500 and M501 commands -#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_SETTINGS // Enable for M500 and M501 commands +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. // diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h index 4406f8ed6..8187e8926 100644 --- a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h +++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h @@ -123,7 +123,7 @@ #endif // Show extra position information in M114 -//#define M114_DETAIL +#define M114_DETAIL // Show Temperature ADC value // Enable for M105 to include ADC values read from temperature sensors. @@ -471,7 +471,7 @@ // @section lcd // Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU +#define LCD_INFO_MENU // Leave out seldom-used LCD menu items to recover some Program Memory //#define SLIM_LCD_MENUS @@ -552,7 +552,7 @@ #define FOLDER_SORTING -1 // -1=above 0=none 1=below #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. #define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting. - #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_USES_STACK true // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. @@ -582,7 +582,7 @@ //#define LONG_FILENAME_HOST_SUPPORT // Enable this option to scroll long filenames in the SD card menu - //#define SCROLL_LONG_FILENAMES + #define SCROLL_LONG_FILENAMES /** * This option allows you to abort SD printing when any endstop is triggered. @@ -614,7 +614,7 @@ */ #if ENABLED(DOGLCD) // Show SD percentage next to the progress bar - //#define DOGM_SD_PERCENT + #define DOGM_SD_PERCENT // Enable to save many cycles by drawing a hollow frame on the Info Screen #define XYZ_HOLLOW_FRAME @@ -736,7 +736,7 @@ // // G2/G3 Arc Support // -//#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment #define N_ARC_CORRECTION 25 // Number of intertpolated segments between corrections @@ -821,7 +821,7 @@ // enter the serial receive buffer, so they cannot be blocked. // Currently handles M108, M112, M410 // Does not work on boards using AT90USB (USBCON) processors! -//#define EMERGENCY_PARSER +#define EMERGENCY_PARSER // Bad Serial-connections can miss a received command by sending an 'ok' // Therefore some clients abort after 30 seconds in a timeout. @@ -830,7 +830,7 @@ //#define NO_TIMEOUTS 1000 // Milliseconds // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. -//#define ADVANCED_OK +#define ADVANCED_OK // @section extras