Revive and improve DELTA probe bounds, LRFB options (#15372)

Marlin/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp

@@ -1391,6 +1391,18 @@
                   dx = (x_max - x_min) / (g29_grid_size - 1),
                   dy = (y_max - y_min) / (g29_grid_size - 1);
 
+      vector_3 points[3] = {
+        #if ENABLED(HAS_FIXED_3POINT)
+          vector_3(PROBE_PT_1_X, PROBE_PT_1_Y, 0),
+          vector_3(PROBE_PT_2_X, PROBE_PT_2_Y, 0),
+          vector_3(PROBE_PT_3_X, PROBE_PT_3_Y, 0)
+        #else
+          vector_3(x_min, y_min, 0),
+          vector_3(x_max, y_min, 0),
+          vector_3((x_max - x_min) / 2, y_max, 0)
+        #endif
+      };
+
       float measured_z;
       bool abort_flag = false;
 
@@ -1407,11 +1419,11 @@
           ui.status_printf_P(0, PSTR(MSG_LCD_TILTING_MESH " 1/3"));
         #endif
 
-        measured_z = probe_at_point(x_min, y_min, PROBE_PT_RAISE, g29_verbose_level);
+        measured_z = probe_at_point(points[0].x, points[0].y, PROBE_PT_RAISE, g29_verbose_level);
         if (isnan(measured_z))
           abort_flag = true;
         else {
-          measured_z -= get_z_correction(x_min, y_min);
+          measured_z -= get_z_correction(points[0].x, points[0].y);
           #ifdef VALIDATE_MESH_TILT
             z1 = measured_z;
           #endif
@@ -1419,7 +1431,7 @@
             serial_spaces(16);
             SERIAL_ECHOLNPAIR("Corrected_Z=", measured_z);
           }
-          incremental_LSF(&lsf_results, x_min, y_min, measured_z);
+          incremental_LSF(&lsf_results, points[0].x, points[0].y, measured_z);
         }
 
         if (!abort_flag) {
@@ -1428,19 +1440,19 @@
             ui.status_printf_P(0, PSTR(MSG_LCD_TILTING_MESH " 2/3"));
           #endif
 
-          measured_z = probe_at_point(x_max, y_min, PROBE_PT_RAISE, g29_verbose_level);
+          measured_z = probe_at_point(points[1].x, points[1].y, PROBE_PT_RAISE, g29_verbose_level);
           #ifdef VALIDATE_MESH_TILT
             z2 = measured_z;
           #endif
           if (isnan(measured_z))
             abort_flag = true;
           else {
-            measured_z -= get_z_correction(x_max, y_min);
+            measured_z -= get_z_correction(points[1].x, points[1].y);
             if (g29_verbose_level > 3) {
               serial_spaces(16);
               SERIAL_ECHOLNPAIR("Corrected_Z=", measured_z);
             }
-            incremental_LSF(&lsf_results, x_max, y_min, measured_z);
+            incremental_LSF(&lsf_results, points[1].x, points[1].y, measured_z);
           }
         }
 
@@ -1450,20 +1462,19 @@
             ui.status_printf_P(0, PSTR(MSG_LCD_TILTING_MESH " 3/3"));
           #endif
 
-          const float center_probe = (x_max - x_min) / 2;
+          measured_z = probe_at_point(points[2].x, points[2].y, PROBE_PT_STOW, g29_verbose_level);
-          measured_z = probe_at_point(center_probe, y_max, PROBE_PT_STOW, g29_verbose_level);
           #ifdef VALIDATE_MESH_TILT
             z3 = measured_z;
           #endif
           if (isnan(measured_z))
             abort_flag = true;
           else {
-            measured_z -= get_z_correction(center_probe, y_max);
+            measured_z -= get_z_correction(points[2].x, points[2].y);
             if (g29_verbose_level > 3) {
               serial_spaces(16);
               SERIAL_ECHOLNPAIR("Corrected_Z=", measured_z);
             }
-            incremental_LSF(&lsf_results, center_probe, y_max, measured_z);
+            incremental_LSF(&lsf_results, points[2].x, points[2].y, measured_z);
           }
         }
 

Marlin/src/gcode/bedlevel/abl/G29.cpp

@@ -267,10 +267,17 @@ G29_TYPE GcodeSuite::G29() {
 
     // Probe at 3 arbitrary points
     const float x_min = probe_min_x(), x_max = probe_max_x(), y_min = probe_min_y(), y_max = probe_max_y();
+
     ABL_VAR vector_3 points[3] = {
+    #if ENABLED(HAS_FIXED_3POINT)
+      vector_3(PROBE_PT_1_X, PROBE_PT_1_Y, 0),
+      vector_3(PROBE_PT_2_X, PROBE_PT_2_Y, 0),
+      vector_3(PROBE_PT_3_X, PROBE_PT_3_Y, 0)
+    #else
       vector_3(x_min, y_min, 0),
       vector_3(x_max, y_min, 0),
       vector_3((x_max - x_min) / 2, y_max, 0)
+    #endif
     };
 
   #endif // AUTO_BED_LEVELING_3POINT

Marlin/src/inc/Conditionals_post.h

@@ -1448,6 +1448,18 @@
 #ifndef MIN_PROBE_EDGE
   #define MIN_PROBE_EDGE 0
 #endif
+#ifndef MIN_PROBE_EDGE_LEFT
+  #define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+#endif
+#ifndef MIN_PROBE_EDGE_RIGHT
+  #define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+#endif
+#ifndef MIN_PROBE_EDGE_FRONT
+  #define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+#endif
+#ifndef MIN_PROBE_EDGE_BACK
+  #define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
 
 #ifndef NOZZLE_TO_PROBE_OFFSET
   #define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
@@ -1490,10 +1502,10 @@
 
   #define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
   #define _PROBE_RADIUS (SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
-  #define PROBE_X_MIN (X_CENTER - (SCARA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE)
+  #define PROBE_X_MIN (X_CENTER - (SCARA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE_LEFT)
-  #define PROBE_Y_MIN (Y_CENTER - (SCARA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE)
+  #define PROBE_Y_MIN (Y_CENTER - (SCARA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE_FRONT)
-  #define PROBE_X_MAX (X_CENTER +  SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
+  #define PROBE_X_MAX (X_CENTER +  SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE_RIGHT))
-  #define PROBE_Y_MAX (Y_CENTER +  SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
+  #define PROBE_Y_MAX (Y_CENTER +  SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE_BACK))
 #endif
 
 #if ENABLED(SEGMENT_LEVELED_MOVES) && !defined(LEVELED_SEGMENT_LENGTH)
@@ -1503,7 +1515,7 @@
 /**
  * Default mesh area is an area with an inset margin on the print area.
  */
-#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL, AUTO_BED_LEVELING_BILINEAR)
+#if HAS_LEVELING
   #if IS_KINEMATIC
     // Probing points may be verified at compile time within the radius
     // using static_assert(HYPOT2(X2-X1,Y2-Y1)<=sq(DELTA_PRINTABLE_RADIUS),"bad probe point!")
@@ -1543,6 +1555,38 @@
 
 #endif // MESH_BED_LEVELING || AUTO_BED_LEVELING_UBL
 
+#if ALL(PROBE_PT_1_X, PROBE_PT_2_X, PROBE_PT_3_X, PROBE_PT_1_Y, PROBE_PT_2_Y, PROBE_PT_3_Y)
+  #define HAS_FIXED_3POINT;
+#endif
+
+#if EITHER(AUTO_BED_LEVELING_UBL, AUTO_BED_LEVELING_3POINT) && IS_KINEMATIC
+    #define HAS_FIXED_3POINT
+    #define SIN0    0.0
+    #define SIN120  0.866025
+    #define SIN240 -0.866025
+    #define COS0    1.0
+    #define COS120 -0.5
+    #define COS240 -0.5
+    #ifndef PROBE_PT_1_X
+      #define PROBE_PT_1_X (X_CENTER + (_PROBE_RADIUS) * COS0)
+    #endif
+    #ifndef PROBE_PT_1_Y
+      #define PROBE_PT_1_Y (Y_CENTER + (_PROBE_RADIUS) * SIN0)
+    #endif
+    #ifndef PROBE_PT_2_X
+      #define PROBE_PT_2_X (X_CENTER + (_PROBE_RADIUS) * COS120)
+    #endif
+    #ifndef PROBE_PT_2_Y
+      #define PROBE_PT_2_Y (Y_CENTER + (_PROBE_RADIUS) * SIN120)
+    #endif
+    #ifndef PROBE_PT_3_X
+      #define PROBE_PT_3_X (X_CENTER + (_PROBE_RADIUS) * COS240)
+    #endif
+    #ifndef PROBE_PT_3_Y
+      #define PROBE_PT_3_Y (Y_CENTER + (_PROBE_RADIUS) * SIN240)
+    #endif
+#endif
+
 /**
  * Buzzer/Speaker
  */

Marlin/src/inc/SanityCheck.h

@@ -251,8 +251,14 @@
   #error "ABL_PROBE_PT_[123]_[XY] is no longer required. Please remove it from Configuration.h."
 #elif defined(UBL_PROBE_PT_1_X) || defined(UBL_PROBE_PT_1_Y) || defined(UBL_PROBE_PT_2_X) || defined(UBL_PROBE_PT_2_Y) || defined(UBL_PROBE_PT_3_X) || defined(UBL_PROBE_PT_3_Y)
   #error "UBL_PROBE_PT_[123]_[XY] is no longer required. Please remove it from Configuration.h."
-#elif defined(PROBE_PT_1_X) || defined(PROBE_PT_1_Y) || defined(PROBE_PT_2_X) || defined(PROBE_PT_2_Y) || defined(PROBE_PT_3_X) || defined(PROBE_PT_3_Y)
+#elif defined(LEFT_PROBE_BED_POSITION)
-  #error "PROBE_PT_[123]_[XY] is no longer required. Please remove it from Configuration.h."
+  #error LEFT_PROBE_BED_POSITION has been replaced by MIN_PROBE_EDGE_LEFT. Please note the differences and update your configuration."
+#elif defined(RIGHT_PROBE_BED_POSITION)
+  #error RIGHT_PROBE_BED_POSITION has been replaced by MIN_PROBE_EDGE_RIGHT. Please note the differences and update your configuration."
+#elif defined(FRONT_PROBE_BED_POSITION)
+  #error FRONT_PROBE_BED_POSITION has been replaced by MIN_PROBE_EDGE_FRONT. Please note the differences and update your configuration."
+#elif defined(BACK_PROBE_BED_POSITION)
+  #error BACK_PROBE_BED_POSITION has been replaced by MIN_PROBE_EDGE_BACK. Please note the differences and update your configuration."
 #elif defined(ENABLE_MESH_EDIT_GFX_OVERLAY)
   #error "ENABLE_MESH_EDIT_GFX_OVERLAY is now MESH_EDIT_GFX_OVERLAY. Please update your configuration."
 #elif defined(BABYSTEP_ZPROBE_GFX_REVERSE)

Marlin/src/module/probe.h

@@ -50,61 +50,56 @@
     extern const char msg_wait_for_bed_heating[25];
   #endif
 
-  #if HAS_LEVELING
-
-    inline float probe_min_x() {
-      return _MAX(
-        #if ENABLED(DELTA) || IS_SCARA
-          PROBE_X_MIN, MESH_MIN_X
-        #else
-          (X_MIN_BED) + (MIN_PROBE_EDGE), (X_MIN_POS) + probe_offset[X_AXIS]
-        #endif
-      );
-    }
-
-    inline float probe_max_x() {
-      return _MIN(
-        #if ENABLED(DELTA) || IS_SCARA
-          PROBE_X_MAX, MESH_MAX_X
-        #else
-          (X_MAX_BED) - (MIN_PROBE_EDGE), (X_MAX_POS) + probe_offset[X_AXIS]
-        #endif
-      );
-    }
-
-    inline float probe_min_y() {
-      return _MAX(
-        #if ENABLED(DELTA) || IS_SCARA
-          PROBE_Y_MIN, MESH_MIN_Y
-        #else
-          (Y_MIN_BED) + (MIN_PROBE_EDGE), (Y_MIN_POS) + probe_offset[Y_AXIS]
-        #endif
-      );
-    }
-
-    inline float probe_max_y() {
-      return _MIN(
-        #if ENABLED(DELTA) || IS_SCARA
-          PROBE_Y_MAX, MESH_MAX_Y
-        #else
-          (Y_MAX_BED) - (MIN_PROBE_EDGE), (Y_MAX_POS) + probe_offset[Y_AXIS]
-        #endif
-      );
-    }
-
-  #endif
-
 #else
 
   constexpr float probe_offset[XYZ] = { 0 };
   #define DEPLOY_PROBE()
   #define STOW_PROBE()
 
+#endif
+
+#if HAS_LEVELING && HAS_BED_PROBE
+  inline float probe_min_x() {
+    return _MAX(
+      #if IS_KINEMATIC
+        PROBE_X_MIN, MESH_MIN_X
+      #else
+        (X_MIN_BED) + (MIN_PROBE_EDGE_LEFT), (X_MIN_POS) + probe_offset[X_AXIS]
+      #endif
+    );
+  }
+  inline float probe_max_x() {
+    return _MIN(
+      #if IS_KINEMATIC
+        PROBE_X_MAX, MESH_MAX_X
+      #else
+        (X_MAX_BED) - (MIN_PROBE_EDGE_RIGHT), (X_MAX_POS) + probe_offset[X_AXIS]
+      #endif
+    );
+  }
+  inline float probe_min_y() {
+    return _MAX(
+      #if IS_KINEMATIC
+        PROBE_Y_MIN, MESH_MIN_Y
+      #else
+        (Y_MIN_BED) + (MIN_PROBE_EDGE_FRONT), (Y_MIN_POS) + probe_offset[Y_AXIS]
+      #endif
+    );
+  }
+  inline float probe_max_y() {
+    return _MIN(
+      #if IS_KINEMATIC
+        PROBE_Y_MAX, MESH_MAX_Y
+      #else
+        (Y_MAX_BED) - (MIN_PROBE_EDGE_BACK), (Y_MAX_POS) + probe_offset[Y_AXIS]
+      #endif
+    );
+  }
+#else
   inline float probe_min_x() { return 0; };
   inline float probe_max_x() { return 0; };
   inline float probe_min_y() { return 0; };
   inline float probe_max_y() { return 0; };
-
 #endif
 
 #if HAS_Z_SERVO_PROBE

config/default/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/ADIMLab/Gantry v1/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/ADIMLab/Gantry v2/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Alfawise/U20-bltouch/Configuration_adv.h

@@ -1342,6 +1342,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Alfawise/U20/Configuration_adv.h

@@ -1341,6 +1341,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Anet/A2/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Anet/A2plus/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Anet/A6/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Anet/A8/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Anet/A8plus/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Anet/E16/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/ArmEd/Configuration_adv.h

@@ -1341,6 +1341,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -1345,6 +1345,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Cartesio/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Creality/CR-10/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Creality/CR-10S/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Creality/CR-10_5S/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Creality/CR-20 Pro/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Creality/CR-20/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Creality/CR-8/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Creality/Ender-3/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Creality/Ender-4/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Creality/Ender-5/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Dagoma/Disco Ultimate/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Einstart-S/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/FYSETC/AIO_II/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/FYSETC/Cheetah/base/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/FYSETC/F6_13/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Felix/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/FlashForge/CreatorPro/Configuration_adv.h

@@ -1336,6 +1336,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

@@ -1341,6 +1341,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X 4

config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -1341,6 +1341,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X 4

config/examples/Geeetech/A10/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Geeetech/A10M/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Geeetech/A20M/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -1336,6 +1336,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/HMS434/Configuration_adv.h

@@ -1316,6 +1316,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/JGAurora/A1/Configuration_adv.h

@@ -1342,6 +1342,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/JGAurora/A5/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/JGAurora/A5S/Configuration_adv.h

@@ -1342,6 +1342,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/MakerParts/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Malyan/M150/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Malyan/M200/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Mks/Robin/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Mks/Sbase/Configuration_adv.h

@@ -1338,6 +1338,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/RapideLite/RL200/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/RigidBot/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/SCARA/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Sanguinololu/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Tevo/Michelangelo/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Tevo/Tarantula Pro/Configuration_adv.h

@@ -1333,6 +1333,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/TheBorg/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/TinyBoy2/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Tronxy/X3A/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Tronxy/X5S-2E/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/UltiMachine/Archim1/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/VORONDesign/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Velleman/K8200/Configuration_adv.h

@@ -1350,6 +1350,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Velleman/K8400/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/WASP/PowerWASP/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Wanhao/Duplicator 6/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/Anycubic/Kossel/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/Dreammaker/Overlord/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/FLSUN/kossel/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/MKS/SBASE/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/Tevo Little Monster/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/generic/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/kossel_mini/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/delta/kossel_xl/Configuration_adv.h

@@ -1339,6 +1339,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/makibox/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/tvrrug/Round2/Configuration_adv.h

@@ -1337,6 +1337,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET

config/examples/wt150/Configuration_adv.h

@@ -1338,6 +1338,42 @@
 
 // @section leveling
 
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Override MIN_PROBE_EDGE for each side of the build plate
+ * Useful to get probe points to exact positions on targets or
+ * to allow leveling to avoid plate clamps on only specific
+ * sides of the bed.
+ * 
+ * If you are replacing the prior *_PROBE_BED_POSITION options,
+ * LEFT and FRONT values in most cases will map directly over
+ * RIGHT and REAR would be the inverse such as 
+ * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
+ * 
+ * This will allow all positions to match at compilation, however
+ * should the probe position be modified with M851XY then the
+ * probe points will follow. This prevents any change from causing
+ * the probe to be unable to reach any points.
+ */
+#if PROBE_SELECTED && !IS_KINEMATIC
+  //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE
+  //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE
+#endif
+
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET