diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index 33dddfc1c..02aecfdf4 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -391,50 +391,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -486,6 +442,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h index 9c3d42760..ed87eae12 100644 --- a/Marlin/example_configurations/Felix/DUAL/Configuration.h +++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h @@ -389,50 +389,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -484,6 +440,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index 52ad056d1..a0a953c39 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -401,50 +401,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -496,6 +452,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h index 62168c19d..95e9e7f37 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration.h @@ -403,50 +403,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -498,6 +454,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index 6846bcf46..e8a196e5a 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -426,50 +426,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -521,6 +477,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index 84088cefc..fb099ba0f 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -409,50 +409,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -504,6 +460,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index ec965013e..993637676 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -403,50 +403,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -498,6 +454,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index ef69905dd..b9aaff7fc 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -417,50 +417,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -512,6 +468,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index 91549d73c..49d7afc98 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -430,50 +430,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -525,6 +481,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index a4c2445e8..8a54cbed2 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -401,50 +401,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -496,6 +452,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index 30cf6eec9..6b28ed222 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -409,50 +409,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -504,6 +460,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h index 846d7609d..28dd41bcc 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h @@ -451,50 +451,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -583,6 +539,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #endif // Z_PROBE_ALLEN_KEY +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index a50d083c0..093d064ac 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -451,50 +451,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -577,6 +533,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #endif // Z_PROBE_ALLEN_KEY +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index 45fe403ab..79a0dc36c 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -451,50 +451,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -580,6 +536,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // Z_PROBE_ALLEN_KEY +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index 205c87c80..2aacb3b55 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -440,50 +440,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -574,6 +530,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // Z_PROBE_ALLEN_KEY +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h index c516ec73b..7f363d70f 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h @@ -449,50 +449,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -575,6 +531,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // Z_PROBE_ALLEN_KEY +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index c0dac4093..2731ae6a2 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -412,50 +412,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -507,6 +463,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index 7b56b9cc3..8874f019f 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -399,50 +399,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //============================= Z Probe Options ============================= //=========================================================================== -// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. -// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. -// -// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** -// -// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. -// Example: To park the head outside the bed area when homing with G28. -// -// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. -// -// For a servo-based Z probe, you must set up servo support below, including -// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. -// -// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. -// - Use 5V for powered (usu. inductive) sensors. -// - Otherwise connect: -// - normally-closed switches to GND and D32. -// - normally-open switches to 5V and D32. -// -// Normally-closed switches are advised and are the default. -// -// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) -// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the -// default pin for all RAMPS-based boards. Some other boards map differently. -// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. -// -// WARNING: -// Setting the wrong pin may have unexpected and potentially disastrous consequences. -// Use with caution and do your homework. -// -//#define Z_MIN_PROBE_ENDSTOP - -// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. -// The Z_MIN_PIN will then be used for both Z-homing and probing. -#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN - -// To use a probe you must enable one of the two options above! - -// This option disables the use of the Z_MIN_PROBE_PIN -// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a -// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. -// If you're using the Z MIN endstop connector for your Z probe, this has no effect. -//#define DISABLE_Z_MIN_PROBE_ENDSTOP - // // Probe Type // Probes are sensors/switches that are activated / deactivated before/after use. @@ -494,6 +450,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Allen Key Probe is defined in the Delta example configurations. // +// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. +// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. +// +// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** +// +// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING. +// Example: To park the head outside the bed area when homing with G28. +// +// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN. +// +// For a servo-based Z probe, you must set up servo support below, including +// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES. +// +// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin. +// - Use 5V for powered (usu. inductive) sensors. +// - Otherwise connect: +// - normally-closed switches to GND and D32. +// - normally-open switches to 5V and D32. +// +// Normally-closed switches are advised and are the default. +// +// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.) +// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the +// default pin for all RAMPS-based boards. Some other boards map differently. +// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file. +// +// WARNING: +// Setting the wrong pin may have unexpected and potentially disastrous consequences. +// Use with caution and do your homework. +// +//#define Z_MIN_PROBE_ENDSTOP + +// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. +// The Z_MIN_PIN will then be used for both Z-homing and probing. +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +// To use a probe you must enable one of the two options above! + +// This option disables the use of the Z_MIN_PROBE_PIN +// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a +// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. +// If you're using the Z MIN endstop connector for your Z probe, this has no effect. +//#define DISABLE_Z_MIN_PROBE_ENDSTOP + // Enable Z Probe Repeatability test to see how accurate your probe is //#define Z_MIN_PROBE_REPEATABILITY_TEST