commit
b6623a0d49
1 changed files with 10 additions and 10 deletions
|
@ -10,7 +10,7 @@
|
||||||
* G10 - retract filament according to settings of M207
|
* G10 - retract filament according to settings of M207
|
||||||
* G11 - retract recover filament according to settings of M208
|
* G11 - retract recover filament according to settings of M208
|
||||||
* G28 - Home all Axis
|
* G28 - Home all Axis
|
||||||
* G29 - Detailed Z-Probe, probes the bed at 3 points. You must de at the home position for this to work correctly.
|
* G29 - Detailed Z-Probe, probes the bed at 3 points. You must be at the home position for this to work correctly.
|
||||||
* G30 - Single Z Probe, probes bed at current XY location.
|
* G30 - Single Z Probe, probes bed at current XY location.
|
||||||
* G31 - Dock Z Probe sled (if enabled)
|
* G31 - Dock Z Probe sled (if enabled)
|
||||||
* G32 - Undock Z Probe sled (if enabled)
|
* G32 - Undock Z Probe sled (if enabled)
|
||||||
|
@ -68,36 +68,36 @@
|
||||||
* M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec
|
* M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec
|
||||||
* M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate
|
* M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate
|
||||||
* M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk
|
* M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk
|
||||||
* M206 - set additional homeing offset
|
* M206 - set additional homing offset
|
||||||
* M207 - set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop], stays in mm regardless of M200 setting
|
* M207 - set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop], stays in mm regardless of M200 setting
|
||||||
* M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/min]
|
* M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/min]
|
||||||
* M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
|
* M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction.
|
||||||
* M218 - set hotend offset (in mm): T<extruder_number> X<offset_on_X> Y<offset_on_Y>
|
* M218 - set hotend offset (in mm): T<extruder_number> X<offset_on_X> Y<offset_on_Y>
|
||||||
* M220 S<factor in percent>- set speed factor override percentage
|
* M220 - S[factor in percent] - set speed factor override percentage
|
||||||
* M221 S<factor in percent>- set extrude factor override percentage
|
* M221 - S[factor in percent] - set extrude factor override percentage
|
||||||
* M240 - Trigger a camera to take a photograph
|
* M240 - Trigger a camera to take a photograph
|
||||||
* M280 - Position an RC Servo P<index> S<angle/microseconds>, ommit S to report back current angle
|
* M280 - Position an RC Servo P<index> S<angle/microseconds>, ommit S to report back current angle
|
||||||
* M300 - Play beepsound S<frequency Hz> P<duration ms>
|
* M300 - Play beep sound S<frequency Hz> P<duration ms>
|
||||||
* M301 - Set PID parameters P I and D
|
* M301 - Set PID parameters P I and D
|
||||||
* M302 - Allow cold extrudes
|
* M302 - Allow cold extrudes
|
||||||
* M303 - PID relay autotune S<temperature> sets the target temperature. (default target temperature = 150C)
|
* M303 - PID relay autotune S<temperature> sets the target temperature. (default target temperature = 150C)
|
||||||
* M304 - Set bed PID parameters P I and D
|
* M304 - Set bed PID parameters P I and D
|
||||||
|
* M350 - Set microstepping mode.
|
||||||
|
* M351 - Toggle MS1 MS2 pins directly.
|
||||||
* M400 - Finish all moves
|
* M400 - Finish all moves
|
||||||
* M401 - Lower z-probe if present
|
* M401 - Lower z-probe if present
|
||||||
* M402 - Raise z-probe if present
|
* M402 - Raise z-probe if present
|
||||||
* M404 - N<dia in mm> Enter the nominal filament width (3mm, 1.75mm ) or will display nominal filament width without parameters
|
* M404 - N<dia in mm> Enter the nominal filament width (3mm, 1.75mm) or will display nominal filament width without parameters
|
||||||
* M405 - Turn on Filament Sensor extrusion control. Optional D<delay in cm> to set delay in centimeters between sensor and extruder
|
* M405 - Turn on Filament Sensor extrusion control. Optional D[delay in cm] to set delay in centimeters between sensor and extruder
|
||||||
* M406 - Turn off Filament Sensor extrusion control
|
* M406 - Turn off Filament Sensor extrusion control
|
||||||
* M407 - Displays measured filament diameter
|
* M407 - Displays measured filament diameter
|
||||||
* M500 - stores paramters in EEPROM
|
* M500 - stores paramters in EEPROM
|
||||||
* M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
* M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||||
* M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
* M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||||
* M503 - print the current settings (from memory not from eeprom)
|
* M503 - print the current settings (from memory not from EEPROM)
|
||||||
* M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
|
* M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
|
||||||
* M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
|
* M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
|
||||||
* M907 - Set digital trimpot motor current using axis codes.
|
* M907 - Set digital trimpot motor current using axis codes.
|
||||||
* M908 - Control digital trimpot directly.
|
* M908 - Control digital trimpot directly.
|
||||||
* M350 - Set microstepping mode.
|
|
||||||
* M351 - Toggle MS1 MS2 pins directly.
|
|
||||||
* M928 - Start SD logging (M928 filename.g) - ended by M29
|
* M928 - Start SD logging (M928 filename.g) - ended by M29
|
||||||
* M999 - Restart after being stopped by error
|
* M999 - Restart after being stopped by error
|
||||||
|
|
Reference in a new issue