Move BLTouch options to adv config (#14131)

Plus other BLTouch and menu enhancements.

Marlin/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

Marlin/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

Marlin/src/lcd/language/language_en.h

@@ -933,6 +933,9 @@
 #ifndef MSG_BLTOUCH_MODE_ECHO
   #define MSG_BLTOUCH_MODE_ECHO               _UxGT("Report Drain")
 #endif
+#ifndef MSG_BLTOUCH_MODE_CHANGE
+  #define MSG_BLTOUCH_MODE_CHANGE             _UxGT("DANGER: Bad settings can cause damage! Proceed anyway?")
+#endif
 #ifndef MSG_MANUAL_DEPLOY
   #define MSG_MANUAL_DEPLOY                   _UxGT("Deploy Z-Probe")
 #endif

Marlin/src/lcd/menu/menu_configuration.cpp

@@ -199,11 +199,19 @@ static void lcd_factory_settings() {
     MENU_ITEM(function, MSG_BLTOUCH_STOW, bltouch._stow);
     MENU_ITEM(function, MSG_BLTOUCH_SW_MODE, bltouch._set_SW_mode);
     #if ENABLED(BLTOUCH_LCD_VOLTAGE_MENU)
-      MENU_ITEM(function, MSG_BLTOUCH_5V_MODE, bltouch._set_5V_mode);
+      MENU_ITEM(submenu, MSG_BLTOUCH_5V_MODE, []{
-      MENU_ITEM(function, MSG_BLTOUCH_OD_MODE, bltouch._set_OD_mode);
+        do_select_screen(PSTR(MSG_BLTOUCH_5V_MODE), PSTR(MSG_BUTTON_CANCEL), bltouch._set_5V_mode, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
+      });
+      MENU_ITEM(submenu, MSG_BLTOUCH_OD_MODE, []{
+        do_select_screen(PSTR(MSG_BLTOUCH_OD_MODE), PSTR(MSG_BUTTON_CANCEL), bltouch._set_OD_mode, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
+      });
       MENU_ITEM(function, MSG_BLTOUCH_MODE_STORE, bltouch._mode_store);
-      MENU_ITEM(function, MSG_BLTOUCH_MODE_STORE_5V, bltouch.mode_conv_5V);
+      MENU_ITEM(submenu, MSG_BLTOUCH_MODE_STORE_5V, []{
-      MENU_ITEM(function, MSG_BLTOUCH_MODE_STORE_OD, bltouch.mode_conv_OD);
+        do_select_screen(PSTR(MSG_BLTOUCH_MODE_STORE_5V), PSTR(MSG_BUTTON_CANCEL), bltouch.mode_conv_5V, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
+      });
+      MENU_ITEM(submenu, MSG_BLTOUCH_MODE_STORE_OD, []{
+        do_select_screen(PSTR(MSG_BLTOUCH_MODE_STORE_OD), PSTR(MSG_BUTTON_CANCEL), bltouch.mode_conv_OD, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
+      });
       MENU_ITEM(function, MSG_BLTOUCH_MODE_ECHO, bltouch_report);
     #endif
     END_MENU();

Marlin/src/lcd/ultralcd.cpp

@@ -196,10 +196,39 @@ millis_t next_button_update_ms;
 
   #endif
 
-  void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte) {
+  void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte, bool wordwrap/*=false*/) {
     SETCURSOR(x, y);
-    if (string) {
+    if (!string) return;
+
     uint8_t *p = (uint8_t*)string;
+    if (wordwrap) {
+      uint8_t *wrd = p, c = 0;
+      for (;;) {
+        wchar_t ch;
+        p = get_utf8_value_cb(p, cb_read_byte, &ch);
+        const bool eol = !ch;
+        if (eol || ch == ' ' || ch == '-' || ch == '+' || ch == '.') {
+          if (!c && ch == ' ') continue; // collapse extra spaces
+          if (x + c > LCD_WIDTH && c < (LCD_WIDTH) * 3 / 4) { // should it wrap?
+            x = 0; y++;               // move x to string len (plus space)
+            SETCURSOR(0, y);          // simulate carriage return
+          }
+          c += !eol;                  // +1 so the space will be printed
+          x += c;                     // advance x to new position
+          while (c--) {               // character countdown
+            wrd = get_utf8_value_cb(wrd, cb_read_byte, &ch); // get characters again
+            lcd_put_wchar(ch);        // word (plus space) to the LCD
+          }
+          if (eol) break;             // all done
+          wrd = nullptr;              // set up for next word
+        }
+        else {
+          if (!wrd) wrd = p;          // starting a new word?
+          c++;                        // count word characters
+        }
+      }
+    }
+    else {
       for (;;) {
         wchar_t ch;
         p = get_utf8_value_cb(p, cb_read_byte, &ch);
@@ -221,7 +250,7 @@ millis_t next_button_update_ms;
       x = (LCD_WIDTH - plen - slen) / 2;
       y = LCD_HEIGHT > 3 ? 1 : 0;
     }
-    wrap_string_P(x, y, pref);
+    wrap_string_P(x, y, pref, true);
     if (string) {
       if (x) { x = 0; y++; } // Move to the start of the next line
       wrap_string(x, y, string);

Marlin/src/lcd/ultralcd.h

@@ -74,9 +74,9 @@
 
     #include "fontutils.h"
 
-    void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte);
+    void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte, const bool wordwrap=false);
-    inline void wrap_string_P(uint8_t &x, uint8_t &y, PGM_P const pstr) { _wrap_string(x, y, pstr, read_byte_rom); }
+    inline void wrap_string_P(uint8_t &x, uint8_t &y, PGM_P const pstr, const bool wordwrap=false) { _wrap_string(x, y, pstr, read_byte_rom, wordwrap); }
-    inline void wrap_string(uint8_t &x, uint8_t &y, const char * const string) { _wrap_string(x, y, string, read_byte_ram); }
+    inline void wrap_string(uint8_t &x, uint8_t &y, const char * const string, const bool wordwrap=false) { _wrap_string(x, y, string, read_byte_ram, wordwrap); }
 
     #if ENABLED(SDSUPPORT)
       #include "../sd/cardreader.h"

config/default/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/default/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -834,72 +834,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/AlephObjects/TAZ4/Configuration.h

@@ -848,72 +848,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/AliExpress/CL-260/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -839,72 +839,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Anet/A2/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Anet/A2/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Anet/A2plus/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Anet/A2plus/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Anet/A6/Configuration.h

@@ -875,72 +875,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Anet/A6/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Anet/A8/Configuration.h

@@ -841,72 +841,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Anet/A8/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Anet/A8plus/Configuration.h

@@ -839,72 +839,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Anet/A8plus/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Anet/E16/Configuration.h

@@ -840,72 +840,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  #define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Anet/E16/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/AnyCubic/i3/Configuration.h

@@ -838,72 +838,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 #define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/ArmEd/Configuration.h

@@ -829,72 +829,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/ArmEd/Configuration_adv.h

@@ -528,6 +528,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Azteeg/X5GT/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/BIBO/TouchX/default/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/BQ/Hephestos/Configuration.h

@@ -816,72 +816,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/BQ/Hephestos_2/Configuration.h

@@ -829,72 +829,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/BQ/WITBOX/Configuration.h

@@ -816,72 +816,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Cartesio/Configuration.h

@@ -827,72 +827,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Cartesio/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Creality/CR-10/Configuration.h

@@ -838,72 +838,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  #define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Creality/CR-10/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  #define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Creality/CR-10S/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  #define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Creality/CR-10S/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  #define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Creality/CR-10_5S/Configuration.h

@@ -829,72 +829,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  #define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Creality/CR-10_5S/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  #define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Creality/CR-10mini/Configuration.h

@@ -847,72 +847,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  #define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  #define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Creality/CR-8/Configuration.h

@@ -838,72 +838,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  #define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Creality/CR-8/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  #define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Creality/Ender-2/Configuration.h

@@ -832,72 +832,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  #define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  #define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Creality/Ender-3/Configuration.h

@@ -832,72 +832,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  #define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Creality/Ender-3/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  #define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Creality/Ender-4/Configuration.h

@@ -838,72 +838,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  #define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Creality/Ender-4/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  #define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Dagoma/Disco Ultimate/Configuration_adv.h

@@ -523,6 +523,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Einstart-S/Configuration.h

@@ -837,72 +837,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Einstart-S/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Felix/Configuration.h

@@ -810,72 +810,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Felix/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Felix/DUAL/Configuration.h

@@ -810,72 +810,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/FlashForge/CreatorPro/Configuration.h

@@ -820,72 +820,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/FlashForge/CreatorPro/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/FolgerTech/i3-2020/Configuration.h

@@ -834,72 +834,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Formbot/Raptor/Configuration.h

@@ -911,72 +911,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 #define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Formbot/T_Rex_2+/Configuration.h

@@ -857,73 +857,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 #define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
-
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

@@ -528,6 +528,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Formbot/T_Rex_3/Configuration.h

@@ -844,72 +844,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 #define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -528,6 +528,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Geeetech/A10M/Configuration.h

@@ -811,72 +811,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  #define BLTOUCH_DELAY 200
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  #define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Geeetech/A10M/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  #define BLTOUCH_DELAY 200
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  #define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Geeetech/A20M/Configuration.h

@@ -811,72 +811,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  #define BLTOUCH_DELAY 200
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  #define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Geeetech/A20M/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  #define BLTOUCH_DELAY 200
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  #define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Geeetech/GT2560/Configuration.h

@@ -843,72 +843,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -828,9 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  //#define BLTOUCH_DELAY 500   // Minimum Command delay (ms). Enable and increase if needed
-#endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Geeetech/MeCreator2/Configuration.h

@@ -835,72 +835,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -848,72 +848,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 #define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -848,72 +848,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Infitary/i3-M508/Configuration.h

@@ -832,72 +832,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/JGAurora/A5/Configuration.h

@@ -840,72 +840,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/JGAurora/A5/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/MakerParts/Configuration.h

@@ -848,72 +848,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/MakerParts/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Malyan/M150/Configuration.h

@@ -848,72 +848,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Malyan/M150/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Malyan/M200/Configuration.h

@@ -827,72 +827,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Malyan/M200/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Micromake/C1/basic/Configuration.h

@@ -832,72 +832,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Micromake/C1/enhanced/Configuration.h

@@ -832,72 +832,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Mks/Robin/Configuration.h

@@ -829,72 +829,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Mks/Robin/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Mks/Sbase/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Mks/Sbase/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Printrbot/PrintrboardG2/Configuration.h

@@ -836,72 +836,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/RapideLite/RL200/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/RapideLite/RL200/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/RepRapPro/Huxley/Configuration.h

@@ -868,72 +868,6 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/RigidBot/Configuration.h

@@ -826,72 +826,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/RigidBot/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/SCARA/Configuration.h

@@ -841,72 +841,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/SCARA/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/STM32/Black_STM32F407VET6/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/STM32/STM32F10/Configuration.h

@@ -830,72 +830,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/STM32/STM32F4/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/STM32/stm32f103ret6/Configuration.h

@@ -830,72 +830,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Sanguinololu/Configuration.h

@@ -859,72 +859,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Sanguinololu/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/TheBorg/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/TheBorg/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/TinyBoy2/Configuration.h

@@ -879,72 +879,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/TinyBoy2/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Tronxy/X1/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Tronxy/X3A/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Tronxy/X3A/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Tronxy/X5S-2E/Configuration.h

@@ -849,72 +849,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Tronxy/X5S-2E/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Tronxy/X5S/Configuration.h

@@ -827,72 +827,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Tronxy/XY100/Configuration.h

@@ -839,72 +839,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/UltiMachine/Archim1/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/UltiMachine/Archim1/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/UltiMachine/Archim2/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/VORONDesign/Configuration.h

@@ -837,72 +837,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/VORONDesign/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Velleman/K8200/Configuration.h

@@ -857,72 +857,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Velleman/K8200/Configuration_adv.h

@@ -537,6 +537,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Velleman/K8400/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Velleman/K8400/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/WASP/PowerWASP/Configuration.h

@@ -847,72 +847,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/WASP/PowerWASP/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/Wanhao/Duplicator 6/Configuration.h

@@ -838,72 +838,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/Wanhao/Duplicator 6/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/adafruit/ST7565/Configuration.h

@@ -828,72 +828,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/Anycubic/Kossel/Configuration.h

@@ -964,72 +964,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/Anycubic/Kossel/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -910,72 +910,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/delta/FLSUN/kossel/Configuration.h

@@ -910,72 +910,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/FLSUN/kossel/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -910,72 +910,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/delta/Geeetech/Rostock 301/Configuration.h

@@ -900,72 +900,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/delta/Hatchbox_Alpha/Configuration.h

@@ -915,72 +915,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/MKS/SBASE/Configuration.h

@@ -900,72 +900,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/MKS/SBASE/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/delta/Tevo Little Monster/Configuration.h

@@ -904,9 +904,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 #define BLTOUCH
-#if ENABLED(BLTOUCH)
-  #define BLTOUCH_DELAY 500   // (ms) Enable and increase if needed
-#endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/Tevo Little Monster/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  #define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/delta/generic/Configuration.h

@@ -900,72 +900,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/generic/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/delta/kossel_mini/Configuration.h

@@ -900,72 +900,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/kossel_mini/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/delta/kossel_pro/Configuration.h

@@ -893,72 +893,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/kossel_xl/Configuration.h

@@ -903,72 +903,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/delta/kossel_xl/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/gCreate/gMax1.5+/Configuration.h

@@ -841,9 +841,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 #define BLTOUCH
-#if ENABLED(BLTOUCH)
-  #define BLTOUCH_DELAY 500   // (ms) Enable and increase if needed
-#endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/makibox/Configuration.h

@@ -831,72 +831,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/makibox/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/tvrrug/Round2/Configuration.h

@@ -823,72 +823,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/tvrrug/Round2/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.

config/examples/wt150/Configuration.h

@@ -833,72 +833,6 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
-  /**
-   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
-   * Do not activate settings that the probe might not understand. Clones might misunderstand
-   * advanced commands.
-   *
-   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
-   *       check the wiring of the BROWN, RED and ORANGE wires.
-   *
-   * Note: If the trigger signal of your probe is not being recognized, it has been very often
-   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
-   *       like they would be with a real switch. So please check the wiring first.
-   *
-   * Settings for all BLTouch and clone probes:
-   */
-
-  // Safety: The probe needs time to recognize the command.
-  //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
-
-  /**
-   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
-   */
-
-  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
-  //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
-
-  /**
-   * Settings for BLTouch Smart 3.0 and 3.1
-   * Summary:
-   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
-   *   - High-Speed mode
-   *   - Disable LCD voltage options
-   */
-
-  /**
-   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
-   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
-   * If disabled, OD mode is the hard-coded default on 3.0
-   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
-   * differs, a mode set eeprom write will be completed at initialization.
-   * Use the option below to force an eeprom write to a V3.1 probe regardless.
-   */
-  //#define BLTOUCH_SET_5V_MODE
-
-  /**
-   * Safety: Activate if connecting a probe with an unknown voltage mode.
-   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
-   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
-   * To preserve the life of the probe, use this once then turn it off and re-flash.
-   */
-  //#define BLTOUCH_FORCE_MODE_SET
-
-  /**
-   * Use "HIGH SPEED" mode for probing.
-   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
-   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
-   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
-   */
-  //#define BLTOUCH_HS_MODE
-
-  // Safety: Enable voltage mode settings in the LCD menu.
-  //#define BLTOUCH_LCD_VOLTAGE_MENU
-
-#endif // BLTOUCH
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE

config/examples/wt150/Configuration_adv.h

@@ -524,6 +524,73 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  /**
+   * Use "HIGH SPEED" mode for probing.
+   * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
+   * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
+   * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
+   */
+  //#define BLTOUCH_HS_MODE
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 /**
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.