From b7fcb1158044609d9f46ac00e8bc3f10f66bc833 Mon Sep 17 00:00:00 2001 From: brupje Date: Thu, 7 May 2015 13:18:05 +0200 Subject: [PATCH] Added example configuration for Megatronics --- .../Megatronics/Configuration_megatronics.h | 817 ++++++++++++++++++ 1 file changed, 817 insertions(+) create mode 100644 Marlin/example_configurations/RepRapWorld/Megatronics/Configuration_megatronics.h diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration_megatronics.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration_megatronics.h new file mode 100644 index 000000000..c62845989 --- /dev/null +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration_megatronics.h @@ -0,0 +1,817 @@ +#ifndef CONFIGURATION_H +#define CONFIGURATION_H + +#include "boards.h" + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== +/* +Here are some standard links for getting your machine calibrated: + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 +*/ + +// This configuration file contains the basic settings. +// Advanced settings can be found in Configuration_adv.h +// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer replace the configuration files with the files in the +// example_configurations/delta directory. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a Scara printer replace the configuration files with the files in the +// example_configurations/SCARA directory. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_VERSION "1.0.3 dev" +#define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time +#define STRING_CONFIG_H_AUTHOR "RepRapWorld.com" // Who made the changes. +#define STRING_SPLASH_LINE1 "v" STRING_VERSION // will be shown during bootup in line 1 +//#define STRING_SPLASH_LINE2 STRING_VERSION_CONFIG_H // will be shown during bootup in line2 + +// @section machine + +// SERIAL_PORT selects which serial port should be used for communication with the host. +// This allows the connection of wireless adapters (for instance) to non-default port pins. +// Serial port 0 is still used by the Arduino bootloader regardless of this setting. +// :[0,1,2,3,4,5,6,7] +#define SERIAL_PORT 0 + +// This determines the communication speed of the printer +// :[2400,9600,19200,38400,57600,115200,250000] +#define BAUDRATE 250000 + +// This enables the serial port associated to the Bluetooth interface +//#define BTENABLED // Enable BT interface on AT90USB devices + +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_MEGATRONICS_3 +#endif + +// Optional custom name for your RepStrap or other custom machine +// Displayed in the LCD "Ready" message +// #define CUSTOM_MACHINE_NAME "3D Printer" + +// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) +// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// This defines the number of extruders +// :[1,2,3,4] +#define EXTRUDERS 1 + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis + +//// The following define selects which power supply you have. Please choose the one that matches your setup +// 1 = ATX +// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) +// :{1:'ATX',2:'X-Box 360'} + +#define POWER_SUPPLY 1 + +// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. +// #define PS_DEFAULT_OFF + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== +// +//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table +// +//// Temperature sensor settings: +// -2 is thermocouple with MAX6675 (only for sensor 0) +// -1 is thermocouple with AD595 +// 0 is not used +// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) +// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) +// 3 is Mendel-parts thermistor (4.7k pullup) +// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! +// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) +// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) +// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) +// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) +// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) +// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) +// 10 is 100k RS thermistor 198-961 (4.7k pullup) +// 11 is 100k beta 3950 1% thermistor (4.7k pullup) +// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) +// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" +// 20 is the PT100 circuit found in the Ultimainboard V2.x +// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 +// +// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k +// (but gives greater accuracy and more stable PID) +// 51 is 100k thermistor - EPCOS (1k pullup) +// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) +// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) +// +// 1047 is Pt1000 with 4k7 pullup +// 1010 is Pt1000 with 1k pullup (non standard) +// 147 is Pt100 with 4k7 pullup +// 110 is Pt100 with 1k pullup (non standard) +// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below. +// Use it for Testing or Development purposes. NEVER for production machine. +// #define DUMMY_THERMISTOR_998_VALUE 25 +// #define DUMMY_THERMISTOR_999_VALUE 100 +// :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" } +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_BED 1 + +// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +// Actual temperature must be close to target for this long before M109 returns success +#define TEMP_RESIDENCY_TIME 10 // (seconds) +#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// The minimal temperature defines the temperature below which the heater will not be enabled It is used +// to check that the wiring to the thermistor is not broken. +// Otherwise this would lead to the heater being powered on all the time. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define BED_MINTEMP 5 + +// When temperature exceeds max temp, your heater will be switched off. +// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! +// You should use MINTEMP for thermistor short/failure protection. +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define BED_MAXTEMP 150 + +// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the +// average current. The value should be an integer and the heat bed will be turned on for 1 interval of +// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. +//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 + +// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS +//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#ifdef PIDTEMP + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term + #define K1 0.95 //smoothing factor within the PID + #define PID_dT ((16.0 * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine + +// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it +// Ultimaker + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 + +// MakerGear +// #define DEFAULT_Kp 7.0 +// #define DEFAULT_Ki 0.1 +// #define DEFAULT_Kd 12 + +// Mendel Parts V9 on 12V +// #define DEFAULT_Kp 63.0 +// #define DEFAULT_Ki 2.25 +// #define DEFAULT_Kd 440 +#endif // PIDTEMP + +//=========================================================================== +//============================= PID > Bed Temperature Control =============== +//=========================================================================== +// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis +// +// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. +// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz, +// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. +// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. +// If your configuration is significantly different than this and you don't understand the issues involved, you probably +// shouldn't use bed PID until someone else verifies your hardware works. +// If this is enabled, find your own PID constants below. +//#define PIDTEMPBED +// +//#define BED_LIMIT_SWITCHING + +// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. +// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) +// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, +// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +//#define PID_BED_DEBUG // Sends debug data to the serial port. + +#ifdef PIDTEMPBED +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from pidautotune +// #define DEFAULT_bedKp 97.1 +// #define DEFAULT_bedKi 1.41 +// #define DEFAULT_bedKd 1675.16 + +// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit +//can be software-disabled for whatever purposes by +#define PREVENT_DANGEROUS_EXTRUDE +//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately. +#define PREVENT_LENGTHY_EXTRUDE + +#define EXTRUDE_MINTEMP 170 +#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. + +//=========================================================================== +//============================= Thermal Runaway Protection ================== +//=========================================================================== +/* +This is a feature to protect your printer from burn up in flames if it has +a thermistor coming off place (this happened to a friend of mine recently and +motivated me writing this feature). + +The issue: If a thermistor come off, it will read a lower temperature than actual. +The system will turn the heater on forever, burning up the filament and anything +else around. + +After the temperature reaches the target for the first time, this feature will +start measuring for how long the current temperature stays below the target +minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). + +If it stays longer than _PERIOD, it means the thermistor temperature +cannot catch up with the target, so something *may be* wrong. Then, to be on the +safe side, the system will he halt. + +Bear in mind the count down will just start AFTER the first time the +thermistor temperature is over the target, so you will have no problem if +your extruder heater takes 2 minutes to hit the target on heating. + +*/ +// If you want to enable this feature for all your extruder heaters, +// uncomment the 2 defines below: + +// Parameters for all extruder heaters +#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds +#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius + +// If you want to enable this feature for your bed heater, +// uncomment the 2 defines below: + +// Parameters for the bed heater +#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds +#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius + + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment this option to enable CoreXY kinematics +// #define COREXY + +// Enable this option for Toshiba steppers +// #define CONFIG_STEPPERS_TOSHIBA + +// @section homing + +// coarse Endstop Settings +#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors + +#ifndef ENDSTOPPULLUPS + // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined + // #define ENDSTOPPULLUP_XMAX + // #define ENDSTOPPULLUP_YMAX + // #define ENDSTOPPULLUP_ZMAX + // #define ENDSTOPPULLUP_XMIN + // #define ENDSTOPPULLUP_YMIN + // #define ENDSTOPPULLUP_ZMIN + // #define ENDSTOPPULLUP_ZPROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. +//#define DISABLE_MAX_ENDSTOPS +//#define DISABLE_MIN_ENDSTOPS + +// @section machine +// If you want to enable the Z Probe pin, but disable its use, uncomment the line below. +// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have +// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe, +// this has no effect. +//#define DISABLE_Z_PROBE_ENDSTOP + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{0:'Low',1:'High'} +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR false +#define INVERT_Y_DIR false +#define INVERT_Z_DIR false + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR false +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false + +// @section homing + +// ENDSTOP SETTINGS: +// Sets direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS. +#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. + +// @section machine + +// Travel limits after homing (units are in mm) +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS 200 +#define Y_MAX_POS 200 +#define Z_MAX_POS 200 + +//=========================================================================== +//============================= Filament Runout Sensor ====================== +//=========================================================================== +//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament + // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. + // It is assumed that when logic high = filament available + // when logic low = filament ran out +//const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned +//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. + +//=========================================================================== +//============================ Mesh Bed Leveling ============================ +//=========================================================================== + +// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling +// #define MESH_BED_LEVELING // Enable mesh bed leveling + +#ifdef MANUAL_BED_LEVELING + #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis +#endif // MANUAL_BED_LEVELING + +#ifdef MESH_BED_LEVELING + #define MESH_MIN_X 10 + #define MESH_MAX_X (X_MAX_POS - MESH_MIN_X) + #define MESH_MIN_Y 10 + #define MESH_MAX_Y (Y_MAX_POS - MESH_MIN_Y) + #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited + #define MESH_NUM_Y_POINTS 3 + #define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0 +#endif // MESH_BED_LEVELING + +//=========================================================================== +//============================= Bed Auto Leveling =========================== +//=========================================================================== + +// @section bedlevel + +//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) +#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. + +#ifdef ENABLE_AUTO_BED_LEVELING + + // There are 2 different ways to specify probing locations + // + // - "grid" mode + // Probe several points in a rectangular grid. + // You specify the rectangle and the density of sample points. + // This mode is preferred because there are more measurements. + // + // - "3-point" mode + // Probe 3 arbitrary points on the bed (that aren't colinear) + // You specify the XY coordinates of all 3 points. + + // Enable this to sample the bed in a grid (least squares solution) + // Note: this feature generates 10KB extra code size + #define AUTO_BED_LEVELING_GRID + + #ifdef AUTO_BED_LEVELING_GRID + + #define LEFT_PROBE_BED_POSITION 15 + #define RIGHT_PROBE_BED_POSITION 170 + #define FRONT_PROBE_BED_POSITION 20 + #define BACK_PROBE_BED_POSITION 170 + + #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this + + // Set the number of grid points per dimension + // You probably don't need more than 3 (squared=9) + #define AUTO_BED_LEVELING_GRID_POINTS 2 + + #else // !AUTO_BED_LEVELING_GRID + + // Arbitrary points to probe. A simple cross-product + // is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 + + #endif // AUTO_BED_LEVELING_GRID + + // Offsets to the probe relative to the extruder tip (Hotend - Probe) + // X and Y offsets must be integers + #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // Probe on: -left +right + #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Probe on: -front +behind + #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!) + + #define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance. + // Be sure you have this distance over your Z_MAX_POS in case + + #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min + + #define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point. + #define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points + #define Z_RAISE_AFTER_PROBING 15 //How much the extruder will be raised after the last probing point. + +// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine. + //Useful to retract a deployable probe. + + //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell + //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + + //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk + //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it. + // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile. + +// #define PROBE_SERVO_DEACTIVATION_DELAY 300 + + +//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, +//it is highly recommended you let this Z_SAFE_HOMING enabled!!! + + #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area. + // When defined, it will: + // - Allow Z homing only after X and Y homing AND stepper drivers still enabled + // - If stepper drivers timeout, it will need X and Y homing again before Z homing + // - Position the probe in a defined XY point before Z Homing when homing all axis (G28) + // - Block Z homing only when the probe is outside bed area. + + #ifdef Z_SAFE_HOMING + + #define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2) // X point for Z homing when homing all axis (G28) + #define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2) // Y point for Z homing when homing all axis (G28) + + #endif + + // Support for a dedicated Z PROBE endstop separate from the Z MIN endstop. + // If you would like to use both a Z PROBE and a Z MIN endstop together or just a Z PROBE with a custom pin, uncomment #define Z_PROBE_ENDSTOP and read the instructions below. + // If you want to still use the Z min endstop for homing, disable Z_SAFE_HOMING above. Eg; to park the head outside the bed area when homing with G28. + // WARNING: The Z MIN endstop will need to set properly as it would without a Z PROBE to prevent head crashes and premature stopping during a print. + // To use a separate Z PROBE endstop, you must have a Z_PROBE_PIN defined in the pins.h file for your control board. + // If you are using a servo based Z PROBE, you will need to enable NUM_SERVOS, SERVO_ENDSTOPS and SERVO_ENDSTOPS_ANGLES in the R/C Servo below. + // RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin in the Aux 4 section of the RAMPS board. Use 5V for powered sensors, otherwise connect to ground and D32 + // for normally closed configuration and 5V and D32 for normally open configurations. Normally closed configuration is advised and assumed. + // The D32 pin in Aux 4 on RAMPS maps to the Arduino D32 pin. Z_PROBE_PIN is setting the pin to use on the Arduino. Since the D32 pin on the RAMPS maps to D32 on Arduino, this works. + // D32 is currently selected in the RAMPS 1.3/1.4 pin file. All other boards will need changes to the respective pins_XXXXX.h file. + // WARNING: Setting the wrong pin may have unexpected and potentially disastrous outcomes. Use with caution and do your homework. + + //#define Z_PROBE_ENDSTOP + +#endif // ENABLE_AUTO_BED_LEVELING + + +// @section homing + +// The position of the homing switches +//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used +//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0) + +// Manual homing switch locations: +// For deltabots this means top and center of the Cartesian print volume. +#ifdef MANUAL_HOME_POSITIONS + #define MANUAL_X_HOME_POS 0 + #define MANUAL_Y_HOME_POS 0 + #define MANUAL_Z_HOME_POS 0 + //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing. +#endif + +// @section movement + +/** + * MOVEMENT SETTINGS + */ + +#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min) + +// default settings + +#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402*2,78.7402*2,5120.00,760*1*1.5} // default steps per unit for Ultimaker +#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec) +#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. + +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves + +// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) +#define DEFAULT_XYJERK 20.0 // (mm/sec) +#define DEFAULT_ZJERK 0.4 // (mm/sec) +#define DEFAULT_EJERK 5.0 // (mm/sec) + + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section more + +// Custom M code points +#define CUSTOM_M_CODES +#ifdef CUSTOM_M_CODES + #ifdef ENABLE_AUTO_BED_LEVELING + #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851 + #define Z_PROBE_OFFSET_RANGE_MIN -20 + #define Z_PROBE_OFFSET_RANGE_MAX 20 + #endif +#endif + +// @section extras + +// EEPROM +// The microcontroller can store settings in the EEPROM, e.g. max velocity... +// M500 - stores parameters in EEPROM +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +//define this to enable EEPROM support +//#define EEPROM_SETTINGS + +#ifdef EEPROM_SETTINGS + // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: + #define EEPROM_CHITCHAT // please keep turned on if you can. +#endif + + +// @section temperature + +// Preheat Constants +#define PLA_PREHEAT_HOTEND_TEMP 180 +#define PLA_PREHEAT_HPB_TEMP 70 +#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 + +#define ABS_PREHEAT_HOTEND_TEMP 240 +#define ABS_PREHEAT_HPB_TEMP 110 +#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 + +//==============================LCD and SD support============================= +// @section lcd + +// Define your display language below. Replace (en) with your language code and uncomment. +// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test +// See also language.h +#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) + +// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display. +// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset. +// See also documentation/LCDLanguageFont.md + #define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware + //#define DISPLAY_CHARSET_HD44780_WESTERN + //#define DISPLAY_CHARSET_HD44780_CYRILLIC + +#define ULTRA_LCD //general LCD support, also 16x2 +//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) +#define SDSUPPORT // Enable SD Card Support in Hardware Console +//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication +//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder +//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking +//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. +//#define ULTIPANEL //the UltiPanel as on Thingiverse +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click +//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click + // 0 to disable buzzer feedback. Test with M300 S P +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +//#define PANEL_ONE + +// The MaKr3d Makr-Panel with graphic controller and SD support +// http://reprap.org/wiki/MaKr3d_MaKrPanel +//#define MAKRPANEL + +// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD +// http://panucatt.com +// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib +//#define VIKI2 +//#define miniVIKI + +// The RepRapDiscount Smart Controller (white PCB) +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// The GADGETS3D G3D LCD/SD Controller (blue PCB) +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +//#define G3D_PANEL + +// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB) +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// The RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +#define REPRAPWORLD_KEYPAD +#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click + +// The Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C +//#define RA_CONTROL_PANEL + +/** + * I2C Panels + */ + +//#define LCD_I2C_SAINSMART_YWROBOT + +// PANELOLU2 LCD with status LEDs, separate encoder and click inputs +//#define LCD_I2C_PANELOLU2 + +// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs +//#define LCD_I2C_VIKI + +// Shift register panels +// --------------------- +// 2 wire Non-latching LCD SR from: +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection + +//#define SAV_3DLCD + +// @section extras + +// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +#define SOFT_PWM_SCALE 0 + +// Temperature status LEDs that display the hotend and bet temperature. +// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on. +// Otherwise the RED led is on. There is 1C hysteresis. +//#define TEMP_STAT_LEDS + +// M240 Triggers a camera by emulating a Canon RC-1 Remote +// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ +// #define PHOTOGRAPH_PIN 23 + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder. +//#define BARICUDA + +//define BlinkM/CyzRgb Support +//#define BLINKM + +/*********************************************************************\ +* R/C SERVO support +* Sponsored by TrinityLabs, Reworked by codexmas +**********************************************************************/ + +// Number of servos +// +// If you select a configuration below, this will receive a default value and does not need to be set manually +// set it manually if you have more servos than extruders and wish to manually control some +// leaving it undefined or defining as 0 will disable the servo subsystem +// If unsure, leave commented / disabled +// +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Servo Endstops +// +// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. +// Use M851 to set the z-probe vertical offset from the nozzle. Store that setting with M500. +// +//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1 +//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles + +/**********************************************************************\ + * Support for a filament diameter sensor + * Also allows adjustment of diameter at print time (vs at slicing) + * Single extruder only at this point (extruder 0) + * + * Motherboards + * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector + * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 - Rambo - uses Analog input 3 + * Note may require analog pins to be defined for different motherboards + **********************************************************************/ +// Uncomment below to enable +//#define FILAMENT_SENSOR + +#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) +#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define MEASURED_UPPER_LIMIT 3.3 //upper limit factor used for sensor reading validation in mm +#define MEASURED_LOWER_LIMIT 1.9 //lower limit factor for sensor reading validation in mm +#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + +//defines used in the code +#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + +//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. +//#define FILAMENT_LCD_DISPLAY + + + + + + +#include "Configuration_adv.h" +#include "thermistortables.h" + +#endif //CONFIGURATION_H