SunRed/Marlin-Artillery-M600
Archived
1
0
Fork 0
Code Issues Pull requests Projects Releases Wiki Activity

Correct Kossel Pro Configuration_adv (PR#2473)

Browse source
This commit is contained in:
Richard Wackerbarth 2015-07-19 17:01:53 -05:00
parent 000a6fce46
commit b80a6a8d31
1 changed files with 25 additions and 20 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

45
Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
View file

@ -19,16 +19,11 @@
#define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control
/** /**
* Heating Sanity Check * Thermal Protection parameters
*
* Whenever an M104 or M109 increases the target temperature this will wait for WATCH_TEMP_PERIOD milliseconds,
* and if the temperature hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted, requiring a
* hard reset. This test restarts with any M104/M109, but only if the current temperature is below the target
* by at least 2 * WATCH_TEMP_INCREASE degrees celsius.
*/ */
#ifdef THERMAL_RUNAWAY_PROTECTION_HOTENDS #ifdef THERMAL_PROTECTION_HOTENDS
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_PERIOD 40 // Seconds
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // Degrees Celsius #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
/** /**
* Whenever an M104 or M109 increases the target temperature the firmware will wait for the * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
@ -40,9 +35,9 @@
#define WATCH_TEMP_INCREASE 4 // Degrees Celsius #define WATCH_TEMP_INCREASE 4 // Degrees Celsius
#endif #endif
#ifdef THERMAL_RUNAWAY_PROTECTION_BED #ifdef THERMAL_PROTECTION_BED
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
#endif #endif
#ifdef PIDTEMP #ifdef PIDTEMP
@ -54,14 +49,16 @@
#endif #endif
#endif #endif
/**
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. * Automatic Temperature:
//The maximum buffered steps/sec of the extruder motor are called "se". * The hotend target temperature is calculated by all the buffered lines of gcode.
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor> * The maximum buffered steps/sec of the extruder motor is called "se".
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
// you exit the value by any M109 without F* * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp. * mintemp and maxtemp. Turn this off by excuting M109 without F*
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
#define AUTOTEMP #define AUTOTEMP
#ifdef AUTOTEMP #ifdef AUTOTEMP
#define AUTOTEMP_OLDWEIGHT 0.98 #define AUTOTEMP_OLDWEIGHT 0.98
@ -101,6 +98,11 @@
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100 //#define FAN_KICKSTART_TIME 100
// This defines the minimal speed for the main fan, run in PWM mode
// to enable uncomment and set minimal PWM speed for reliable running (1-255)
// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
//#define FAN_MIN_PWM 50
// @section extruder // @section extruder
// Extruder cooling fans // Extruder cooling fans
@ -366,6 +368,9 @@
//#define PROGRESS_MSG_ONCE //#define PROGRESS_MSG_ONCE
#endif #endif
// This allows hosts to request long names for files and folders with M33
//#define LONG_FILENAME_HOST_SUPPORT
#endif // SDSUPPORT #endif // SDSUPPORT
// for dogm lcd displays you can choose some additional fonts: // for dogm lcd displays you can choose some additional fonts: