Full-featured Alfawise U20 config (#15131)

This commit is contained in:
Tanguy Pruvot 2019-09-02 09:37:50 +02:00 committed by Scott Lahteine
parent 54069823a0
commit b97bb14a7a
2 changed files with 34 additions and 29 deletions

View file

@ -137,8 +137,8 @@
* THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
*/ */
#if ENABLED(THERMAL_PROTECTION_HOTENDS) #if ENABLED(THERMAL_PROTECTION_HOTENDS)
#define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_PERIOD 60 // Seconds
#define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius #define THERMAL_PROTECTION_HYSTERESIS 10 // Degrees Celsius
//#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops
#if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
@ -157,7 +157,7 @@
* and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
* below 2. * below 2.
*/ */
#define WATCH_TEMP_PERIOD 20 // Seconds #define WATCH_TEMP_PERIOD 60 // Seconds
#define WATCH_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
@ -518,7 +518,7 @@
#define X_HOME_BUMP_MM 5 #define X_HOME_BUMP_MM 5
#define Y_HOME_BUMP_MM 5 #define Y_HOME_BUMP_MM 5
#define Z_HOME_BUMP_MM 2 #define Z_HOME_BUMP_MM 2
#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) #define HOMING_BUMP_DIVISOR { 4, 4, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially //#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially
//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing //#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing
@ -543,6 +543,7 @@
* *
* Settings for all BLTouch and clone probes: * Settings for all BLTouch and clone probes:
*/ */
#undef PROBE_MANUALLY
// Safety: The probe needs time to recognize the command. // Safety: The probe needs time to recognize the command.
// Minimum command delay (ms). Enable and increase if needed. // Minimum command delay (ms). Enable and increase if needed.
@ -591,7 +592,7 @@
//#define BLTOUCH_HS_MODE //#define BLTOUCH_HS_MODE
// Safety: Enable voltage mode settings in the LCD menu. // Safety: Enable voltage mode settings in the LCD menu.
//#define BLTOUCH_LCD_VOLTAGE_MENU #define BLTOUCH_LCD_VOLTAGE_MENU
#endif // BLTOUCH #endif // BLTOUCH
@ -854,7 +855,7 @@
#if HAS_LCD_MENU #if HAS_LCD_MENU
// Include a page of printer information in the LCD Main Menu // Include a page of printer information in the LCD Main Menu
//#define LCD_INFO_MENU #define LCD_INFO_MENU
#if ENABLED(LCD_INFO_MENU) #if ENABLED(LCD_INFO_MENU)
//#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
#endif #endif
@ -891,7 +892,7 @@
//#define LCD_TIMEOUT_TO_STATUS 15000 //#define LCD_TIMEOUT_TO_STATUS 15000
// Add an 'M73' G-code to set the current percentage // Add an 'M73' G-code to set the current percentage
//#define LCD_SET_PROGRESS_MANUALLY #define LCD_SET_PROGRESS_MANUALLY
#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
//#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
@ -922,7 +923,7 @@
#define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing
//#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files #define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files
#define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27")
@ -934,7 +935,7 @@
* an option on the LCD screen to continue the print from the last-known * an option on the LCD screen to continue the print from the last-known
* point in the file. * point in the file.
*/ */
//#define POWER_LOSS_RECOVERY #define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY) #if ENABLED(POWER_LOSS_RECOVERY)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
@ -945,6 +946,9 @@
// Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
// especially with "vase mode" printing. Set too high and vases cannot be continued. // especially with "vase mode" printing. Set too high and vases cannot be continued.
#define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
//#define DEBUG_POWER_LOSS_RECOVERY // Debug informations on serial output
//#define SAVE_INFO_INTERVAL_MS 0 // Force SD recov. write interval, on each layer start if 0
#endif #endif
/** /**
@ -970,7 +974,7 @@
* - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
* - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
*/ */
//#define SDCARD_SORT_ALPHA #define SDCARD_SORT_ALPHA
// SD Card Sorting options // SD Card Sorting options
#if ENABLED(SDCARD_SORT_ALPHA) #if ENABLED(SDCARD_SORT_ALPHA)
@ -986,7 +990,7 @@
#endif #endif
// This allows hosts to request long names for files and folders with M33 // This allows hosts to request long names for files and folders with M33
//#define LONG_FILENAME_HOST_SUPPORT #define LONG_FILENAME_HOST_SUPPORT
// Enable this option to scroll long filenames in the SD card menu // Enable this option to scroll long filenames in the SD card menu
//#define SCROLL_LONG_FILENAMES //#define SCROLL_LONG_FILENAMES
@ -1006,7 +1010,7 @@
* On print completion the LCD Menu will open with the file selected. * On print completion the LCD Menu will open with the file selected.
* You can just click to start the print, or navigate elsewhere. * You can just click to start the print, or navigate elsewhere.
*/ */
//#define SD_REPRINT_LAST_SELECTED_FILE #define SD_REPRINT_LAST_SELECTED_FILE
/** /**
* Auto-report SdCard status with M27 S<seconds> * Auto-report SdCard status with M27 S<seconds>
@ -1099,7 +1103,7 @@
*/ */
#if HAS_GRAPHICAL_LCD #if HAS_GRAPHICAL_LCD
// Show SD percentage next to the progress bar // Show SD percentage next to the progress bar
//#define DOGM_SD_PERCENT #define DOGM_SD_PERCENT
// Enable to save many cycles by drawing a hollow frame on the Info Screen // Enable to save many cycles by drawing a hollow frame on the Info Screen
#define XYZ_HOLLOW_FRAME #define XYZ_HOLLOW_FRAME
@ -1155,7 +1159,7 @@
//#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap
//#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap
//#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames
//#define STATUS_HEAT_PERCENT // Show heating in a progress bar #define STATUS_HEAT_PERCENT // Show heating in a progress bar
//#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
//#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of PROGMEM. //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of PROGMEM.
@ -1218,12 +1222,13 @@
// FSMC Graphical TFT // FSMC Graphical TFT
// //
#if ENABLED(FSMC_GRAPHICAL_TFT) #if ENABLED(FSMC_GRAPHICAL_TFT)
//#define TFT_MARLINUI_COLOR 0xFFFF // White // see https://ee-programming-notepad.blogspot.com/2016/10/16-bit-color-generator-picker.html
//#define TFT_MARLINBG_COLOR 0x0000 // Black #define TFT_MARLINUI_COLOR COLOR_WHITE
//#define TFT_DISABLED_COLOR 0x0003 // Almost black #define TFT_MARLINBG_COLOR COLOR_BLACK
//#define TFT_BTCANCEL_COLOR 0xF800 // Red #define TFT_DISABLED_COLOR 0x10A2 // almost black
//#define TFT_BTARROWS_COLOR 0xDEE6 // 11011 110111 00110 Yellow #define TFT_BTCANCEL_COLOR COLOR_RED
//#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan #define TFT_BTARROWS_COLOR COLOR_WHITE
#define TFT_BTOKMENU_COLOR COLOR_BLUE
#endif #endif
// @section safety // @section safety
@ -1420,16 +1425,16 @@
// The number of linear motions that can be in the plan at any give time. // The number of linear motions that can be in the plan at any give time.
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering.
#if ENABLED(SDSUPPORT) #if ENABLED(SDSUPPORT)
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller #define BLOCK_BUFFER_SIZE 32
#else #else
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer #define BLOCK_BUFFER_SIZE 16 // Marlin default
#endif #endif
// @section serial // @section serial
// The ASCII buffer for serial input // The ASCII buffer for serial input
#define MAX_CMD_SIZE 96 #define MAX_CMD_SIZE 96
#define BUFSIZE 4 #define BUFSIZE 8
// Transmission to Host Buffer Size // Transmission to Host Buffer Size
// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
@ -1569,7 +1574,7 @@
* Requires NOZZLE_PARK_FEATURE. * Requires NOZZLE_PARK_FEATURE.
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
*/ */
//#define ADVANCED_PAUSE_FEATURE #define ADVANCED_PAUSE_FEATURE
#if ENABLED(ADVANCED_PAUSE_FEATURE) #if ENABLED(ADVANCED_PAUSE_FEATURE)
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
@ -1590,7 +1595,7 @@
// For direct drive, the full length of the nozzle. // For direct drive, the full length of the nozzle.
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. #define ADVANCED_PAUSE_PURGE_LENGTH 25 // (mm) Length to extrude after loading.
// Set to 0 for manual extrusion. // Set to 0 for manual extrusion.
// Filament can be extruded repeatedly from the Filament Change menu // Filament can be extruded repeatedly from the Filament Change menu
// until extrusion is consistent, and to purge old filament. // until extrusion is consistent, and to purge old filament.
@ -1609,7 +1614,7 @@
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. #define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
#endif #endif

View file

@ -922,7 +922,7 @@
#define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing
#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files #define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files
#define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27")
@ -1424,9 +1424,9 @@
// The number of linear motions that can be in the plan at any give time. // The number of linear motions that can be in the plan at any give time.
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering.
#if ENABLED(SDSUPPORT) #if ENABLED(SDSUPPORT)
#define BLOCK_BUFFER_SIZE 32 // SD,LCD,Buttons take more memory, block buffer needs to be smaller #define BLOCK_BUFFER_SIZE 32
#else #else
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer #define BLOCK_BUFFER_SIZE 16 // Marlin default
#endif #endif
// @section serial // @section serial