Merge pull request #5794 from thinkyhead/rc_m600_improve

M600 wait for heatup, prevent stepper timeout, etc.

Marlin/Configuration_adv.h

@@ -721,12 +721,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/Marlin_main.cpp

@@ -7290,6 +7290,22 @@ inline void gcode_M503() {
 
 #if ENABLED(FILAMENT_CHANGE_FEATURE)
 
+  millis_t next_buzz = 0;
+  unsigned long int runout_beep = 0;
+
+  void filament_change_beep() {
+    const millis_t ms = millis();
+    if (ELAPSED(ms, next_buzz)) {
+      if (runout_beep <= FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS + 5) { // Only beep as long as we're supposed to
+        next_buzz = ms + (runout_beep <= FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS ? 2500 : 400);
+        BUZZ(300, 2000);
+        runout_beep++;
+      }
+    }
+  }
+
+  static bool busy_doing_M600 = false;
+
   /**
    * M600: Pause for filament change
    *
@@ -7310,6 +7326,12 @@ inline void gcode_M503() {
       return;
     }
 
+    busy_doing_M600 = true;  // Stepper Motors can't timeout when this is set
+
+    // Pause the print job timer
+    bool job_running = print_job_timer.isRunning();
+    print_job_timer.pause();
+
     // Show initial message and wait for synchronize steppers
     lcd_filament_change_show_message(FILAMENT_CHANGE_MESSAGE_INIT);
     stepper.synchronize();
@@ -7327,8 +7349,6 @@ inline void gcode_M503() {
       #define RUNPLAN(RATE_MM_S) line_to_destination(RATE_MM_S);
     #endif
 
-    KEEPALIVE_STATE(IN_HANDLER);
-
     // Initial retract before move to filament change position
     if (code_seen('E')) destination[E_AXIS] += code_value_axis_units(E_AXIS);
     #if defined(FILAMENT_CHANGE_RETRACT_LENGTH) && FILAMENT_CHANGE_RETRACT_LENGTH > 0
@@ -7367,6 +7387,7 @@ inline void gcode_M503() {
 
     stepper.synchronize();
     lcd_filament_change_show_message(FILAMENT_CHANGE_MESSAGE_UNLOAD);
+    idle();
 
     // Unload filament
     if (code_seen('L')) destination[E_AXIS] += code_value_axis_units(E_AXIS);
@@ -7384,28 +7405,72 @@ inline void gcode_M503() {
     disable_e3();
     delay(100);
 
-    #if HAS_BUZZER
+    millis_t nozzle_timeout = millis() + FILAMENT_CHANGE_NOZZLE_TIMEOUT * 1000L;
-      millis_t next_buzz = 0;
+    bool nozzle_timed_out = false;
-    #endif
+    float temps[4];
 
     // Wait for filament insert by user and press button
     lcd_filament_change_show_message(FILAMENT_CHANGE_MESSAGE_INSERT);
 
-    // LCD click or M108 will clear this
+    idle();
-    wait_for_user = true;
+
+    wait_for_user = true;    // LCD click or M108 will clear this
+    next_buzz = 0;
+    runout_beep = 0;
+    HOTEND_LOOP() temps[e] = thermalManager.target_temperature[e]; // Save nozzle temps
 
     while (wait_for_user) {
+      millis_t current_ms = millis();
+      if (nozzle_timed_out)
+        lcd_filament_change_show_message(FILAMENT_CHANGE_MESSAGE_CLICK_TO_HEAT_NOZZLE);
+
       #if HAS_BUZZER 
-        millis_t ms = millis();
+        filament_change_beep();
-        if (ms >= next_buzz) {
+      #endif
-          BUZZ(300, 2000);
+
-          next_buzz = ms + 2500; // Beep every 2.5s while waiting
+      if (current_ms >= nozzle_timeout) {
+        if (!nozzle_timed_out) {
+          nozzle_timed_out = true; // on nozzle timeout remember the nozzles need to be reheated
+          HOTEND_LOOP() thermalManager.setTargetHotend(0, e); // Turn off all the nozzles
+          lcd_filament_change_show_message(FILAMENT_CHANGE_MESSAGE_CLICK_TO_HEAT_NOZZLE);
         }
+      }
+      idle(true);
+    }
+
+    if (nozzle_timed_out)      // Turn nozzles back on if they were turned off
+      HOTEND_LOOP() thermalManager.setTargetHotend(temps[e], e);
+
+    // Show "wait for heating"
+    lcd_filament_change_show_message(FILAMENT_CHANGE_MESSAGE_WAIT_FOR_NOZZLES_TO_HEAT);
+
+    wait_for_heatup = true;
+    while (wait_for_heatup) {
+      idle();
+      wait_for_heatup = false;
+      HOTEND_LOOP() {
+        if (abs(thermalManager.degHotend(e) - temps[e]) > 3) {
+          wait_for_heatup = true;
+          break;
+        }
+      }
+    }
+
+    // Show "insert filament"
+    if (nozzle_timed_out)
+      lcd_filament_change_show_message(FILAMENT_CHANGE_MESSAGE_INSERT);
+
+    wait_for_user = true;    // LCD click or M108 will clear this
+    next_buzz = 0;
+    runout_beep = 0;
+    while (wait_for_user && nozzle_timed_out) {
+      #if HAS_BUZZER
+        filament_change_beep();
       #endif
       idle(true);
     }
 
-    // Show load message
+    // Show "load" message
     lcd_filament_change_show_message(FILAMENT_CHANGE_MESSAGE_LOAD);
 
     // Load filament
@@ -7434,8 +7499,6 @@ inline void gcode_M503() {
 
     lcd_filament_change_show_message(FILAMENT_CHANGE_MESSAGE_RESUME);
 
-    KEEPALIVE_STATE(IN_HANDLER);
-
     // Set extruder to saved position
     destination[E_AXIS] = current_position[E_AXIS] = lastpos[E_AXIS];
     planner.set_e_position_mm(current_position[E_AXIS]);
@@ -7459,6 +7522,11 @@ inline void gcode_M503() {
 
     // Show status screen
     lcd_filament_change_show_message(FILAMENT_CHANGE_MESSAGE_STATUS);
+
+    // Resume the print job timer if it was running
+    if (job_running) print_job_timer.start();
+
+    busy_doing_M600 = false;  // Allow Stepper Motors to be turned off during inactivity
   }
 
 #endif // FILAMENT_CHANGE_FEATURE
@@ -10074,7 +10142,14 @@ void manage_inactivity(bool ignore_stepper_queue/*=false*/) {
 
   if (max_inactive_time && ELAPSED(ms, previous_cmd_ms + max_inactive_time)) kill(PSTR(MSG_KILLED));
 
-  if (stepper_inactive_time && ELAPSED(ms, previous_cmd_ms + stepper_inactive_time)
+  // Prevent steppers timing-out in the middle of M600
+  #if ENABLED(FILAMENT_CHANGE_FEATURE) && ENABLED(FILAMENT_CHANGE_NO_STEPPER_TIMEOUT)
+    #define M600_TEST !busy_doing_M600
+  #else
+    #define M600_TEST true
+  #endif
+             
+  if (M600_TEST && stepper_inactive_time && ELAPSED(ms, previous_cmd_ms + stepper_inactive_time)
       && !ignore_stepper_queue && !planner.blocks_queued()) {
     #if ENABLED(DISABLE_INACTIVE_X)
       disable_x();

Marlin/dogm_font_data_ISO10646_1_tr.h

@@ -31,7 +31,7 @@
   X Font      ascent = 7 descent=-1
   Max Font    ascent = 8 descent=-1
 */
-#include "U8glib.h"
+#include <U8glib.h>
 const u8g_fntpgm_uint8_t ISO10646_TR[2591] U8G_SECTION(".progmem.ISO10646_TR") = {
   0,6,9,0,254,7,1,146,3,33,32,255,255,8,255,7,
   255,0,0,0,6,0,0,1,7,7,6,2,0,128,128,128,

Marlin/endstops.cpp

@@ -217,6 +217,10 @@ void Endstops::M119() {
     SERIAL_PROTOCOLPGM(MSG_Z_PROBE);
     SERIAL_PROTOCOLLN(((READ(Z_MIN_PROBE_PIN)^Z_MIN_PROBE_ENDSTOP_INVERTING) ? MSG_ENDSTOP_HIT : MSG_ENDSTOP_OPEN));
   #endif
+  #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+    SERIAL_PROTOCOLPGM(MSG_FILAMENT_RUNOUT_SENSOR);
+    SERIAL_PROTOCOLLN(((READ(FIL_RUNOUT_PIN)^FIL_RUNOUT_INVERTING) ? MSG_ENDSTOP_HIT : MSG_ENDSTOP_OPEN));
+  #endif
 } // Endstops::M119
 
 #if ENABLED(Z_DUAL_ENDSTOPS)

Marlin/enum.h

@@ -143,7 +143,9 @@ enum TempState {
       FILAMENT_CHANGE_MESSAGE_EXTRUDE,
       FILAMENT_CHANGE_MESSAGE_OPTION,
       FILAMENT_CHANGE_MESSAGE_RESUME,
-      FILAMENT_CHANGE_MESSAGE_STATUS
+      FILAMENT_CHANGE_MESSAGE_STATUS,
+      FILAMENT_CHANGE_MESSAGE_CLICK_TO_HEAT_NOZZLE,
+      FILAMENT_CHANGE_MESSAGE_WAIT_FOR_NOZZLES_TO_HEAT
     };
   #endif
 #endif

Marlin/example_configurations/Cartesio/Configuration_adv.h

@@ -695,33 +695,42 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
+/**
-#if ENABLED(ULTIPANEL)
+ * Filament Change
-  // #define FILAMENT_CHANGE_FEATURE             // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+ * Experimental filament change support.
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
+ * Adds the GCode M600 for initiating filament change.
-    #define FILAMENT_CHANGE_X_POS 30            // X position of hotend
+ *
-    #define FILAMENT_CHANGE_Y_POS 10            // Y position of hotend
+ * Requires an LCD display.
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+ */
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+//#define FILAMENT_CHANGE_FEATURE
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 1    // Initial retract in mm
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_X_POS 30            // X position of hotend
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_Y_POS 10            // Y position of hotend
-    //#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-                                                // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 1    // Initial retract in mm
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+  //#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
-                                                // Short or zero length for printers without bowden where loading is not used
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable unloading for manual unloading
-                                                // 0 to disable for manual extrusion
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // or until outcoming filament color is not clear for filament color change
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+                                              // Short or zero length for printers without bowden where loading is not used
-  #endif
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -721,12 +721,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/Hephestos/Configuration_adv.h

@@ -721,12 +721,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/Hephestos_2/Configuration_adv.h

@@ -704,12 +704,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/K8200/Configuration_adv.h

@@ -708,33 +708,42 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
+/**
-#if ENABLED(ULTIPANEL)
+ * Filament Change
-  #define FILAMENT_CHANGE_FEATURE               // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+ * Experimental filament change support.
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
+ * Adds the GCode M600 for initiating filament change.
-    #define FILAMENT_CHANGE_X_POS (X_MAX_POS-3) // X position of hotend
+ *
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+ * Requires an LCD display.
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+ */
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+//#define FILAMENT_CHANGE_FEATURE
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_X_POS (X_MAX_POS-3) // X position of hotend
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-                                                // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Short or zero length for printers without bowden where loading is not used
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable unloading for manual unloading
-                                                // 0 to disable for manual extrusion
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // or until outcoming filament color is not clear for filament color change
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+                                              // Short or zero length for printers without bowden where loading is not used
-  #endif
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/K8400/Configuration_adv.h

@@ -695,33 +695,42 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
+/**
-#if ENABLED(ULTIPANEL)
+ * Filament Change
-  #define FILAMENT_CHANGE_FEATURE               // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+ * Experimental filament change support.
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
+ * Adds the GCode M600 for initiating filament change.
-    #define FILAMENT_CHANGE_X_POS 100           // X position of hotend
+ *
-    #define FILAMENT_CHANGE_Y_POS 100           // Y position of hotend
+ * Requires an LCD display.
-    #define FILAMENT_CHANGE_Z_ADD 20            // Z addition of hotend (lift)
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+ */
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+//#define FILAMENT_CHANGE_FEATURE
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 5    // Initial retract in mm
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_X_POS 100           // X position of hotend
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_Y_POS 100           // Y position of hotend
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 600   // Unload filament length from hotend in mm
+  #define FILAMENT_CHANGE_Z_ADD 20            // Z addition of hotend (lift)
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-                                                // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 5    // Initial retract in mm
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_LOAD_LENGTH 600     // Load filament length over hotend in mm
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 600   // Unload filament length from hotend in mm
-                                                // Short or zero length for printers without bowden where loading is not used
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 100  // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable unloading for manual unloading
-                                                // 0 to disable for manual extrusion
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // or until outcoming filament color is not clear for filament color change
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+                                              // Short or zero length for printers without bowden where loading is not used
-  #endif
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 100  // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -721,12 +721,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -721,12 +721,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/TAZ4/Configuration_adv.h

@@ -703,33 +703,42 @@
   #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
 #endif
 
-// Add support for experimental filament exchange support M600; requires display
+/**
-#if ENABLED(ULTIPANEL)
+ * Filament Change
-  #define FILAMENT_CHANGE_FEATURE               // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+ * Experimental filament change support.
-  #if ENABLED(FILAMENT_CHANGE_FEATURE)
+ * Adds the GCode M600 for initiating filament change.
-    #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
+ *
-    #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
+ * Requires an LCD display.
-    #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
-    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+ */
-    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+//#define FILAMENT_CHANGE_FEATURE
-    #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
+#if ENABLED(FILAMENT_CHANGE_FEATURE)
-                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
+  #define FILAMENT_CHANGE_X_POS 3             // X position of hotend
-    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+  #define FILAMENT_CHANGE_Y_POS 3             // Y position of hotend
-    #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
+  #define FILAMENT_CHANGE_Z_ADD 10            // Z addition of hotend (lift)
-                                                // Longer length for bowden printers to unload filament from whole bowden tube,
+  #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
-                                                // shorter lenght for printers without bowden to unload filament from extruder only,
+  #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
-                                                // 0 to disable unloading for manual unloading
+  #define FILAMENT_CHANGE_RETRACT_LENGTH 2    // Initial retract in mm
-    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+                                              // It is a short retract used immediately after print interrupt before move to filament exchange position
-    #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
+  #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
-                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH 100   // Unload filament length from hotend in mm
-                                                // Short or zero length for printers without bowden where loading is not used
+                                              // Longer length for bowden printers to unload filament from whole bowden tube,
-    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+                                              // shorter lenght for printers without bowden to unload filament from extruder only,
-    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable unloading for manual unloading
-                                                // 0 to disable for manual extrusion
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
-                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+  #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
-                                                // or until outcoming filament color is not clear for filament color change
+                                              // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
-    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+                                              // Short or zero length for printers without bowden where loading is not used
-  #endif
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
+                                              // 0 to disable for manual extrusion
+                                              // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                              // or until outcoming filament color is not clear for filament color change
+  #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/WITBOX/Configuration_adv.h

@@ -721,12 +721,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -723,12 +723,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -723,12 +723,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -728,12 +728,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -723,12 +723,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -721,12 +721,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -721,12 +721,16 @@
   #define FILAMENT_CHANGE_LOAD_LENGTH 0       // Load filament length over hotend in mm
                                               // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
                                               // Short or zero length for printers without bowden where loading is not used
-  #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+  #define FILAMENT_CHANGE_LOAD_FEEDRATE 6     // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
   #define FILAMENT_CHANGE_EXTRUDE_LENGTH 50   // Extrude filament length in mm after filament is load over the hotend,
                                               // 0 to disable for manual extrusion
                                               // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
                                               // or until outcoming filament color is not clear for filament color change
   #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #define FILAMENT_CHANGE_NOZZLE_TIMEOUT 45L  // Turn off nozzle if user doesn't change filament within this time limit in seconds
+  #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS  5L  // Number of alert beeps before printer goes quiet
+  #define FILAMENT_CHANGE_NO_STEPPER_TIMEOUT         // Enable to have stepper motors hold position during filament change
+                                                     // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
 #endif
 
 /******************************************************************************\

Marlin/language.h

@@ -152,6 +152,7 @@
 #define MSG_Z2_MIN                          "z2_min: "
 #define MSG_Z2_MAX                          "z2_max: "
 #define MSG_Z_PROBE                         "z_probe: "
+#define MSG_FILAMENT_RUNOUT_SENSOR          "filament: "
 #define MSG_ERR_MATERIAL_INDEX              "M145 S<index> out of range (0-1)"
 #define MSG_ERR_M355_NONE                   "No case light"
 #define MSG_ERR_M421_PARAMETERS             "M421 required parameters missing"

Marlin/language_en.h

@@ -33,6 +33,9 @@
 #ifndef WELCOME_MSG
   #define WELCOME_MSG                         MACHINE_NAME _UxGT(" ready.")
 #endif
+#ifndef MSG_BACK
+  #define MSG_BACK                            _UxGT("Back")
+#endif
 #ifndef MSG_SD_INSERTED
   #define MSG_SD_INSERTED                     _UxGT("Card inserted")
 #endif
@@ -486,7 +489,6 @@
 #ifndef MSG_DELTA_CALIBRATE_CENTER
   #define MSG_DELTA_CALIBRATE_CENTER          _UxGT("Calibrate Center")
 #endif
-
 #ifndef MSG_INFO_MENU
   #define MSG_INFO_MENU                       _UxGT("About Printer")
 #endif
@@ -583,6 +585,12 @@
 #ifndef MSG_FILAMENT_CHANGE_OPTION_RESUME
   #define MSG_FILAMENT_CHANGE_OPTION_RESUME   _UxGT("Resume print")
 #endif
+#ifndef MSG_FILAMENT_CHANGE_MINTEMP
+  #define MSG_FILAMENT_CHANGE_MINTEMP         _UxGT("Minimum Temp is ")
+#endif
+#ifndef MSG_FILAMENT_CHANGE_NOZZLE
+  #define MSG_FILAMENT_CHANGE_NOZZLE          _UxGT("  Nozzle: ")
+#endif
 
 //
 // Filament Change screens show up to 3 lines on a 4-line display
@@ -603,6 +611,14 @@
     #define MSG_FILAMENT_CHANGE_INSERT_2        _UxGT("and press button")
     #define MSG_FILAMENT_CHANGE_INSERT_3        _UxGT("to continue...")
   #endif
+  #ifndef MSG_FILAMENT_CHANGE_HEAT_1
+    #define MSG_FILAMENT_CHANGE_HEAT_1          _UxGT("Press button to")
+    #define MSG_FILAMENT_CHANGE_HEAT_2          _UxGT("heat nozzle.")
+  #endif
+  #ifndef MSG_FILAMENT_CHANGE_HEATING_1
+    #define MSG_FILAMENT_CHANGE_HEATING_1       _UxGT("Heating nozzle")
+    #define MSG_FILAMENT_CHANGE_HEATING_2       _UxGT("Please wait...")
+  #endif
   #ifndef MSG_FILAMENT_CHANGE_LOAD_1
     #define MSG_FILAMENT_CHANGE_LOAD_1          _UxGT("Wait for")
     #define MSG_FILAMENT_CHANGE_LOAD_2          _UxGT("filament load")
@@ -625,6 +641,9 @@
   #ifndef MSG_FILAMENT_CHANGE_INSERT_1
     #define MSG_FILAMENT_CHANGE_INSERT_1        _UxGT("Insert and Click")
   #endif
+  #ifndef MSG_FILAMENT_CHANGE_HEATING_1
+    #define MSG_FILAMENT_CHANGE_HEATING_1       _UxGT("Heating...")
+  #endif
   #ifndef MSG_FILAMENT_CHANGE_LOAD_1
     #define MSG_FILAMENT_CHANGE_LOAD_1          _UxGT("Loading...")
   #endif

Marlin/ultralcd.cpp

@@ -54,6 +54,7 @@ char lcd_status_message[3 * (LCD_WIDTH) + 1] = WELCOME_MSG; // worst case is kan
 
 #if ENABLED(DOGLCD)
   #include "ultralcd_impl_DOGM.h"
+  #include <U8glib.h>
 #else
   #include "ultralcd_impl_HD44780.h"
 #endif
@@ -151,6 +152,7 @@ uint16_t max_display_update_time = 0;
     void lcd_filament_change_unload_message();
     void lcd_filament_change_insert_message();
     void lcd_filament_change_load_message();
+    void lcd_filament_change_heat_nozzle();
     void lcd_filament_change_extrude_message();
     void lcd_filament_change_resume_message();
   #endif
@@ -948,7 +950,8 @@ void kill_screen(const char* lcd_msg) {
     // Change filament
     //
     #if ENABLED(FILAMENT_CHANGE_FEATURE)
-       MENU_ITEM(function, MSG_FILAMENTCHANGE, lcd_enqueue_filament_change);
+      if (!thermalManager.tooColdToExtrude(active_extruder))
+        MENU_ITEM(function, MSG_FILAMENTCHANGE, lcd_enqueue_filament_change);
     #endif
 
     END_MENU();
@@ -1384,11 +1387,13 @@ KeepDrawing:
         MENU_ITEM(function, MSG_PREHEAT_1, lcd_preheat_material1_hotend0);
         MENU_ITEM(function, MSG_PREHEAT_2, lcd_preheat_material2_hotend0);
       #endif
+
       //
       // Change filament
       //
       #if ENABLED(FILAMENT_CHANGE_FEATURE)
-        MENU_ITEM(function, MSG_FILAMENTCHANGE, lcd_enqueue_filament_change);
+        if (!thermalManager.tooColdToExtrude(active_extruder))
+          MENU_ITEM(function, MSG_FILAMENTCHANGE, lcd_enqueue_filament_change);
       #endif
     #endif
 
@@ -2441,11 +2446,21 @@ KeepDrawing:
     }
   #endif // LCD_INFO_MENU
 
+  /**
+   *
+   * Filament Change Feature Screens
+   *
+   */
   #if ENABLED(FILAMENT_CHANGE_FEATURE)
+
     void lcd_filament_change_toocold_menu() {
       START_MENU();
       STATIC_ITEM(MSG_HEATING_FAILED_LCD, true, true);
-      MENU_BACK(MSG_FILAMENTCHANGE);
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_MINTEMP STRINGIFY(EXTRUDE_MINTEMP) ".", false, false);
+      MENU_BACK(MSG_BACK);
+      STATIC_ITEM(" ");
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_NOZZLE, false, true);
+      lcd_implementation_hotend_status();
       END_MENU();
     }
 
@@ -2478,6 +2493,8 @@ KeepDrawing:
       #ifdef MSG_FILAMENT_CHANGE_INIT_3
         STATIC_ITEM(MSG_FILAMENT_CHANGE_INIT_3);
       #endif
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_NOZZLE, false, true);
+      lcd_implementation_hotend_status();
       END_SCREEN();
     }
 
@@ -2491,6 +2508,35 @@ KeepDrawing:
       #ifdef MSG_FILAMENT_CHANGE_UNLOAD_3
         STATIC_ITEM(MSG_FILAMENT_CHANGE_UNLOAD_3);
       #endif
+      STATIC_ITEM (" ");
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_NOZZLE, false, true);
+      lcd_implementation_hotend_status();
+      END_SCREEN();
+    }
+
+    void lcd_filament_change_wait_for_nozzles_to_heat() {
+      START_SCREEN();
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_HEADER, true, true);
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_HEATING_1);
+      #ifdef MSG_FILAMENT_CHANGE_HEATING_2
+        STATIC_ITEM(MSG_FILAMENT_CHANGE_HEATING_2);
+      #endif
+      STATIC_ITEM(" ");
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_NOZZLE, false, true);
+      lcd_implementation_hotend_status();
+      END_SCREEN();
+    }
+
+    void lcd_filament_change_heat_nozzle() {
+      START_SCREEN();
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_HEADER, true, true);
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_HEAT_1);
+      #ifdef MSG_FILAMENT_CHANGE_INSERT_2
+        STATIC_ITEM(MSG_FILAMENT_CHANGE_HEAT_2);
+      #endif
+      STATIC_ITEM(" ");
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_NOZZLE, false, true);
+      lcd_implementation_hotend_status();
       END_SCREEN();
     }
 
@@ -2504,6 +2550,8 @@ KeepDrawing:
       #ifdef MSG_FILAMENT_CHANGE_INSERT_3
         STATIC_ITEM(MSG_FILAMENT_CHANGE_INSERT_3);
       #endif
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_NOZZLE, false, true);
+      lcd_implementation_hotend_status();
       END_SCREEN();
     }
 
@@ -2517,6 +2565,9 @@ KeepDrawing:
       #ifdef MSG_FILAMENT_CHANGE_LOAD_3
         STATIC_ITEM(MSG_FILAMENT_CHANGE_LOAD_3);
       #endif
+      STATIC_ITEM(" ");
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_NOZZLE, false, true);
+      lcd_implementation_hotend_status();
       END_SCREEN();
     }
 
@@ -2530,6 +2581,9 @@ KeepDrawing:
       #ifdef MSG_FILAMENT_CHANGE_EXTRUDE_3
         STATIC_ITEM(MSG_FILAMENT_CHANGE_EXTRUDE_3);
       #endif
+      STATIC_ITEM(" ");
+      STATIC_ITEM(MSG_FILAMENT_CHANGE_NOZZLE, false, true);
+      lcd_implementation_hotend_status();
       END_SCREEN();
     }
 
@@ -2564,6 +2618,12 @@ KeepDrawing:
         case FILAMENT_CHANGE_MESSAGE_EXTRUDE:
           lcd_goto_screen(lcd_filament_change_extrude_message);
           break;
+        case FILAMENT_CHANGE_MESSAGE_CLICK_TO_HEAT_NOZZLE:
+          lcd_goto_screen(lcd_filament_change_heat_nozzle);
+          break;
+        case FILAMENT_CHANGE_MESSAGE_WAIT_FOR_NOZZLES_TO_HEAT:
+          lcd_goto_screen(lcd_filament_change_wait_for_nozzles_to_heat);
+          break;
         case FILAMENT_CHANGE_MESSAGE_OPTION:
           filament_change_menu_response = FILAMENT_CHANGE_RESPONSE_WAIT_FOR;
           lcd_goto_screen(lcd_filament_change_option_menu);

Marlin/ultralcd_impl_DOGM.h

@@ -379,6 +379,17 @@ FORCE_INLINE void _draw_axis_label(const AxisEnum axis, const char* const pstr,
 
 //#define DOGM_SD_PERCENT
 
+
+static void lcd_implementation_hotend_status() {
+  u8g.setPrintPos(58, 60);
+  lcd_print((char)('0' + active_extruder));
+  lcd_print(' ');
+  lcd_print(' ');
+  lcd_print(itostr3(thermalManager.degHotend(active_extruder)));
+  lcd_print('/');
+  lcd_print(itostr3(thermalManager.degTargetHotend(active_extruder)));
+}
+
 static void lcd_implementation_status_screen() {
 
   bool blink = lcd_blink();

Marlin/ultralcd_impl_HD44780.h

@@ -592,6 +592,14 @@ FORCE_INLINE void _draw_axis_label(const AxisEnum axis, const char* const pstr,
 
 #endif // LCD_PROGRESS_BAR
 
+static void lcd_implementation_hotend_status() {
+  lcd.setCursor(10, 3);
+  lcd.print(LCD_STR_THERMOMETER[active_extruder]);
+  lcd.print(itostr3(thermalManager.degHotend(active_extruder)));
+  lcd.print('/');
+  lcd.print(itostr3(thermalManager.degTargetHotend(active_extruder)));
+}
+
 /**
 Possible status screens:
 16x2   |000/000 B000/000|

README.md

@@ -19,6 +19,7 @@ The latest Release Candidate lives in the ["RC" branch](https://github.com/Marli
 ## Recent Changes
 - RCBugFix
   - Fixed broken MBL
+  - M600 heater timeout option
 
 - RC8 - 06 Dec 2016
   - Major performance improvement for Graphical LCDs