Apply sensorless changes to example configs

This commit is contained in:
Scott Lahteine 2018-09-27 21:29:08 -05:00
parent 3286325044
commit bb47009656
54 changed files with 810 additions and 378 deletions

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1266,11 +1266,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1279,10 +1279,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1260,11 +1260,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1273,10 +1273,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1262,11 +1262,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1275,10 +1275,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1263,11 +1263,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1276,10 +1276,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1266,11 +1266,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1279,10 +1279,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1271,11 +1271,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1284,10 +1284,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1260,11 +1260,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1273,10 +1273,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1260,11 +1260,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1273,10 +1273,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1260,11 +1260,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1273,10 +1273,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1260,11 +1260,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1273,10 +1273,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1260,11 +1260,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1273,10 +1273,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1260,11 +1260,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1273,10 +1273,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1260,11 +1260,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1273,10 +1273,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1260,11 +1260,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1273,10 +1273,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1258,11 +1258,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1271,10 +1271,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**

View file

@ -1259,11 +1259,11 @@
#define E5_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop.
* You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
* Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
* X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity.
* Higher values make the system LESS sensitive.
* Lower value make the system MORE sensitive.
* Too low values can lead to false positives, while too high values will collide the axis without triggering.
@ -1272,10 +1272,18 @@
*/
//#define SENSORLESS_HOMING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING)
#define X_HOMING_SENSITIVITY 8
#define Y_HOMING_SENSITIVITY 8
//#define Z_HOMING_SENSITIVITY 8
/**
* Use StallGuard2 to probe the bed with the nozzle.
*
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature.
*/
//#define SENSORLESS_PROBING // TMC2130 only
#if ENABLED(SENSORLESS_HOMING) || ENABLED(SENSORLESS_PROBING)
#define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8
#endif
/**