Followup for BABYSTEP_HOTEND_Z_OFFSET (#11916)

Marlin/Configuration_adv.h

@@ -770,15 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
-  // Allow babystepping tool z offsets, allowing compensation for tools at different heights.
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
-  // Ignored in Independent X Carriage Duplicate mode, where tool 0 Z probe offset will be used.
+  #endif
-  //#define BABYSTEP_HOTEND_Z_OFFSET
 #endif
 
 // @section extruder

Marlin/src/config/default/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Anet/A2/Configuration_adv.h

@@ -759,11 +759,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h

@@ -759,11 +759,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Anet/A6/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Anet/A8/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -778,11 +778,14 @@
   //#define BABYSTEP_XY                   // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false         // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 2        // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET          // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL  1500  // Maximum interval between clicks, in milliseconds.
                                           // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Cartesio/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR  10 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 5   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 5   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 5   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Einstart-S/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Felix/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR   2 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration.h

@@ -327,7 +327,7 @@
 #define TEMP_SENSOR_4 0
 #define TEMP_SENSOR_5 0
 
-#if(ENABLED(ROXYs_TRex))
+#ifdef ROXYs_TRex
   #define TEMP_SENSOR_BED 11
 #else
 #define TEMP_SENSOR_BED 0
@@ -398,7 +398,7 @@
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
-  #if(ENABLED(ROXYs_TRex))
+  #ifdef ROXYs_TRex
     // Roxy's T-Rex 2+
     #define DEFAULT_Kp 15.17
     #define DEFAULT_Ki 0.88
@@ -455,7 +455,7 @@
 
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
-  #if(ENABLED(ROXYs_TRex))
+  #ifdef ROXYs_TRex
     // T-Rex 2+
     #define DEFAULT_bedKp 289.73
     #define DEFAULT_bedKi 51.26
@@ -953,7 +953,7 @@
 #define Z_MIN_POS 0
 #define X_MAX_POS 450
 #define Y_MAX_POS Y_BED_SIZE
-#if(ENABLED(tallVersion))
+#if ENABLED(tallVersion)
   #define Z_MAX_POS 700
 #else
   #define Z_MAX_POS 500

Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration_adv.h

@@ -774,11 +774,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 40  // Babysteps are very small. Increase for faster motion.
-//#define BABYSTEP_ZPROBE_OFFSET     // Enable to combine M851 and Babystepping
+//#define BABYSTEP_ZPROBE_OFFSET     // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250  // Maximum interval between clicks, in milliseconds.
                                          // Note: Extra time may be added to mitigate controller latency.
 //#define BABYSTEP_ZPROBE_GFX_OVERLAY    // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h

@@ -332,11 +332,11 @@
 #define TEMP_SENSOR_4 0
 #define TEMP_SENSOR_5 0
 
-#if(ENABLED(ROXYs_TRex))
+#ifdef ROXYs_TRex
   #define TEMP_SENSOR_BED 11
 #endif
 
-#if(ENABLED(TREX3))
+#if ENABLED(TREX3)
   #define TEMP_SENSOR_BED 11
 #endif
 
@@ -409,7 +409,7 @@
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
-  #if(ENABLED(ROXYs_TRex))
+  #ifdef ROXYs_TRex
     // Roxy's T-Rex 2+
     #define DEFAULT_Kp 15.17
     #define DEFAULT_Ki 0.88
@@ -466,7 +466,7 @@
 
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
-  #if(ENABLED(ROXYs_TRex))
+  #ifdef ROXYs_TRex
     // T-Rex 2+
     #define DEFAULT_bedKp 289.73
     #define DEFAULT_bedKi 51.26
@@ -964,7 +964,7 @@
 #define Z_MIN_POS 0
 #define X_MAX_POS 450
 #define Y_MAX_POS Y_BED_SIZE
-#if(ENABLED(tallVersion))
+#if ENABLED(tallVersion)
   #define Z_MAX_POS 700
 #else
   #define Z_MAX_POS 500

Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -773,11 +773,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 40  // Babysteps are very small. Increase for faster motion.
-//#define BABYSTEP_ZPROBE_OFFSET     // Enable to combine M851 and Babystepping
+//#define BABYSTEP_ZPROBE_OFFSET     // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250  // Maximum interval between clicks, in milliseconds.
                                          // Note: Extra time may be added to mitigate controller latency.
 //#define BABYSTEP_ZPROBE_GFX_OVERLAY    // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 5   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/MakerParts/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Malyan/M200/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

@@ -778,11 +778,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/RigidBot/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/SCARA/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/TheBorg/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h

@@ -759,11 +759,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h

@@ -783,11 +783,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h

@@ -772,11 +772,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration_adv.h

@@ -754,11 +754,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -772,11 +772,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h

@@ -772,11 +772,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -772,11 +772,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/generic/Configuration_adv.h

@@ -772,11 +772,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h

@@ -772,11 +772,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h

@@ -777,11 +777,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h

@@ -772,11 +772,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR   3 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/makibox/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h

@@ -770,11 +770,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/config/examples/wt150/Configuration_adv.h

@@ -771,11 +771,14 @@
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
   #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_ZPROBE_OFFSET   // Combine M851 Z and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+    //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
+  #endif
 #endif
 
 // @section extruder

Marlin/src/gcode/motion/M290.cpp

@@ -33,27 +33,27 @@
   #include "../../core/serial.h"
 #endif
 
-
 #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
+
   FORCE_INLINE void mod_zprobe_zoffset(const float &offs) {
-    #if ENABLED(BABYSTEP_HOTEND_Z_OFFSET)
+    if (true
-      if (active_extruder == 0)
+      #if ENABLED(BABYSTEP_HOTEND_Z_OFFSET)
-      {
+        && active_extruder == 0
-        zprobe_zoffset += offs;
+      #endif
-        SERIAL_ECHO_START();
+    ) {
-        SERIAL_ECHOLNPAIR(MSG_PROBE_Z_OFFSET ": ", zprobe_zoffset);
-      } else {
-          hotend_offset[Z_AXIS][active_extruder] -= offs;
-          SERIAL_ECHO_START();
-          SERIAL_ECHOLNPAIR(MSG_IDEX_Z_OFFSET ": ", hotend_offset[Z_AXIS][active_extruder]);
-        }
-    #else
       zprobe_zoffset += offs;
       SERIAL_ECHO_START();
       SERIAL_ECHOLNPAIR(MSG_PROBE_Z_OFFSET ": ", zprobe_zoffset);
+    }
+    #if ENABLED(BABYSTEP_HOTEND_Z_OFFSET)
+      else {
+        hotend_offset[Z_AXIS][active_extruder] -= offs;
+        SERIAL_ECHO_START();
+        SERIAL_ECHOLNPAIR(MSG_IDEX_Z_OFFSET ": ", hotend_offset[Z_AXIS][active_extruder]);
+      }
     #endif
-
   }
+
 #endif
 
 /**

Marlin/src/inc/SanityCheck.h

@@ -312,12 +312,15 @@
 #define BOARD_MKS_13     -47
 #define BOARD_TRIGORILLA -343
 #define BOARD_RURAMPS4D  -1550
+#define BOARD_FORMBOT_TREX2 -81
 #if MB(MKS_13)
   #error "BOARD_MKS_13 has been renamed BOARD_MKS_GEN_13. Please update your configuration."
-#elif MB(BOARD_TRIGORILLA)
+#elif MB(TRIGORILLA)
   #error "BOARD_TRIGORILLA has been renamed BOARD_TRIGORILLA_13. Please update your configuration."
-#elif MB(BOARD_RURAMPS4D)
+#elif MB(RURAMPS4D)
   #error "BOARD_RURAMPS4D has been renamed BOARD_RURAMPS4D_11. Please update your configuration."
+#elif MB(FORMBOT_TREX2)
+  #error "FORMBOT_TREX2 has been renamed BOARD_FORMBOT_TREX2PLUS. Please update your configuration."
 #endif
 
 /**
@@ -515,6 +518,8 @@ static_assert(X_MAX_LENGTH >= X_BED_SIZE && Y_MAX_LENGTH >= Y_BED_SIZE,
     #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a Graphical LCD."
   #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && DISABLED(BABYSTEP_ZPROBE_OFFSET)
     #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a BABYSTEP_ZPROBE_OFFSET."
+  #elif ENABLED(BABYSTEP_HOTEND_Z_OFFSET) && !HAS_HOTEND_OFFSET
+    #error "BABYSTEP_HOTEND_Z_OFFSET requires 2 or more HOTENDS."
   #endif
 #endif
 

Marlin/src/lcd/ultralcd.cpp

@@ -1310,42 +1310,46 @@ void lcd_quick_feedback(const bool clear_buttons) {
       void lcd_babystep_zoffset() {
         if (use_click()) { return lcd_goto_previous_menu_no_defer(); }
         defer_return_to_status = true;
+        #if ENABLED(BABYSTEP_HOTEND_Z_OFFSET)
+          const bool do_probe = (active_extruder == 0);
+        #else
+          constexpr bool do_probe = true;
+        #endif
         ENCODER_DIRECTION_NORMAL();
         if (encoderPosition) {
           const int16_t babystep_increment = (int32_t)encoderPosition * (BABYSTEP_MULTIPLICATOR);
           encoderPosition = 0;
 
-          const float new_zoffset = zprobe_zoffset + planner.steps_to_mm[Z_AXIS] * babystep_increment;
+          const float diff = planner.steps_to_mm[Z_AXIS] * babystep_increment,
-          if (WITHIN(new_zoffset, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX)) {
+                      new_probe_offset = zprobe_zoffset + diff,
+                      new_offs =
+                        #if ENABLED(BABYSTEP_HOTEND_Z_OFFSET)
+                          do_probe ? new_probe_offset : hotend_offset[Z_AXIS][active_extruder] - diff
+                        #else
+                          new_probe_offset
+                        #endif
+                      ;
+          if (WITHIN(new_offs, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX)) {
 
+            thermalManager.babystep_axis(Z_AXIS, babystep_increment);
 
+            if (do_probe) zprobe_zoffset = new_offs;
             #if ENABLED(BABYSTEP_HOTEND_Z_OFFSET)
-              if (active_extruder == 0)
+              else hotend_offset[Z_AXIS][active_extruder] = new_offs;
-              {
-                thermalManager.babystep_axis(Z_AXIS, babystep_increment);
-                zprobe_zoffset = new_zoffset;
-              } else {
-                  thermalManager.babystep_axis(Z_AXIS, babystep_increment);
-                  hotend_offset[Z_AXIS][active_extruder] -= (planner.steps_to_mm[Z_AXIS] * babystep_increment);
-                }
-            #else
-              zprobe_zoffset = new_zoffset;
             #endif
+
             lcdDrawUpdate = LCDVIEW_CALL_REDRAW_NEXT;
           }
         }
         if (lcdDrawUpdate) {
           #if ENABLED(BABYSTEP_HOTEND_Z_OFFSET)
-            if (active_extruder == 0) {
+            if (do_probe)
               lcd_implementation_drawedit(PSTR(MSG_ZPROBE_ZOFFSET), ftostr43sign(zprobe_zoffset));
-            } else {
+            else
               lcd_implementation_drawedit(PSTR(MSG_IDEX_Z_OFFSET), ftostr43sign(hotend_offset[Z_AXIS][active_extruder]));
-            }
           #endif
           #if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY)
-            if (active_extruder == 0) {
+            if (do_probe) _lcd_zoffset_overlay_gfx(zprobe_zoffset);
-              _lcd_zoffset_overlay_gfx(zprobe_zoffset);
-            }
           #endif
         }
       }

Marlin/src/module/configuration_store.cpp

@@ -495,12 +495,12 @@ void MarlinSettings::postprocess() {
       for (uint8_t q = mesh_num_x * mesh_num_y; q--;) EEPROM_WRITE(dummy);
     #endif // MESH_BED_LEVELING
 
+    _FIELD_TEST(zprobe_zoffset);
+
     #if !HAS_BED_PROBE
       const float zprobe_zoffset = 0;
     #endif
-
+    EEPROM_WRITE(zprobe_zoffset);
-      _FIELD_TEST(zprobe_zoffset);
-      EEPROM_WRITE(zprobe_zoffset);
 
     //
     // Planar Bed Leveling matrix
@@ -1181,12 +1181,12 @@ void MarlinSettings::postprocess() {
         for (uint16_t q = mesh_num_x * mesh_num_y; q--;) EEPROM_READ(dummy);
       #endif // MESH_BED_LEVELING
 
+      _FIELD_TEST(zprobe_zoffset);
+
       #if !HAS_BED_PROBE
         float zprobe_zoffset;
       #endif
-
+      EEPROM_READ(zprobe_zoffset);
-        _FIELD_TEST(zprobe_zoffset);
-        EEPROM_READ(zprobe_zoffset);
 
       //
       // Planar Bed Leveling matrix

Marlin/src/pins/pins_FORMBOT_TREX2PLUS.h

@@ -143,15 +143,12 @@
 #define HEATER_BED_PIN     58
 
 #define FAN_PIN             9
-#if(DISABLED(FILAMENT_RUNOUT_SENSOR))
-  // Though defined as a fan pin, it is utilized as a dedicated laser pin by Formbot. May
-  // swapped plug and play with a fil;ament runout sensor.
-  #define FAN1_PIN            4 
-#endif
-
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
-  #define FIL_RUNOUT_PIN   4
+  #define FIL_RUNOUT_PIN    4
   //#define FIL_RUNOUT2_PIN  -1
+#else
+  // Though defined as a fan pin, it is utilized as a dedicated laser pin by Formbot.
+  #define FAN1_PIN          4
 #endif
 
 //

buildroot/share/tests/megaatmega2560_tests

@@ -54,7 +54,7 @@ exec_test $1 $2 "Probeless build of AUTO_BED_LEVELING_UBL, with lots of extruder
 opt_enable Z_PROBE_SLED SKEW_CORRECTION SKEW_CORRECTION_FOR_Z SKEW_CORRECTION_GCODE
 opt_set LCD_LANGUAGE jp-kana
 opt_disable SEGMENT_LEVELED_MOVES
-opt_enable_adv BABYSTEP_ZPROBE_OFFSET DOUBLECLICK_FOR_Z_BABYSTEPPING
+opt_enable_adv BABYSTEP_ZPROBE_OFFSET DOUBLECLICK_FOR_Z_BABYSTEPPING BABYSTEP_HOTEND_Z_OFFSET
 exec_test $1 $2 "Add a Sled Z Probe, use UBL Cartesian moves, use Japanese language"
 #
 # Test a Servo Probe