Analog joystick jogging control (#14648)

Marlin/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

Marlin/src/HAL/HAL_STM32F1/HAL.cpp

@@ -121,6 +121,15 @@ const uint8_t adc_pins[] = {
   #if ENABLED(FILAMENT_WIDTH_SENSOR)
     FILWIDTH_PIN,
   #endif
+  #if HAS_JOY_ADC_X
+    JOY_X_PIN,
+  #endif
+  #if HAS_JOY_ADC_Y
+    JOY_Y_PIN,
+  #endif
+  #if HAS_JOY_ADC_Z
+    JOY_Z_PIN,
+  #endif
 };
 
 enum TEMP_PINS : char {
@@ -151,15 +160,20 @@ enum TEMP_PINS : char {
   #if ENABLED(FILAMENT_WIDTH_SENSOR)
     FILWIDTH,
   #endif
+  #if HAS_JOY_ADC_X
+    JOY_X,
+  #endif
+  #if HAS_JOY_ADC_Y
+    JOY_Y,
+  #endif
+  #if HAS_JOY_ADC_Z
+    JOY_Z,
+  #endif
   ADC_PIN_COUNT
 };
 
 uint16_t HAL_adc_results[ADC_PIN_COUNT];
 
-// ------------------------
-// Function prototypes
-// ------------------------
-
 // ------------------------
 // Private functions
 // ------------------------
@@ -305,6 +319,15 @@ void HAL_adc_start_conversion(const uint8_t adc_pin) {
     #if HAS_TEMP_ADC_5
       case TEMP_5_PIN: pin_index = TEMP_5; break;
     #endif
+    #if HAS_JOY_ADC_X
+      case JOY_X_PIN: pin_index = JOY_X; break;
+    #endif
+    #if HAS_JOY_ADC_Y
+      case JOY_Y_PIN: pin_index = JOY_Y; break;
+    #endif
+    #if HAS_JOY_ADC_Z
+      case JOY_Z_PIN: pin_index = JOY_Z; break;
+    #endif
     #if ENABLED(FILAMENT_WIDTH_SENSOR)
       case FILWIDTH_PIN: pin_index = FILWIDTH; break;
     #endif

Marlin/src/Marlin.cpp

@@ -89,6 +89,10 @@
   #include "feature/bltouch.h"
 #endif
 
+#if ENABLED(POLL_JOG)
+  #include "feature/joystick.h"
+#endif
+
 #if HAS_SERVOS
   #include "module/servo.h"
 #endif
@@ -739,6 +743,10 @@ void idle(
   #if ENABLED(PRUSA_MMU2)
     mmu2.mmu_loop();
   #endif
+
+  #if ENABLED(POLL_JOG)
+    joystick.inject_jog_moves();
+  #endif
 }
 
 /**

Marlin/src/core/serial.h

@@ -156,6 +156,8 @@ extern uint8_t marlin_debug_flags;
 
 #define SERIAL_ECHO_SP(C)           serial_spaces(C)
 
+#define SERIAL_ECHO_TERNARY(TF, PRE, ON, OFF, POST) serial_ternary(TF, PSTR(PRE), PSTR(ON), PSTR(OFF), PSTR(POST))
+
 //
 // Functions for serial printing from PROGMEM. (Saves loads of SRAM.)
 //

Marlin/src/feature/I2CPositionEncoder.cpp

@@ -233,7 +233,7 @@ bool I2CPositionEncoder::passes_test(const bool report) {
     switch (H) {
       case I2CPE_MAG_SIG_GOOD:
       case I2CPE_MAG_SIG_MID:
-        serial_ternary(H == I2CPE_MAG_SIG_GOOD, PSTR("passes test; field strength "), PSTR("good"), PSTR("fair"), PSTR(".\n"));
+        SERIAL_ECHO_TERNARY(H == I2CPE_MAG_SIG_GOOD, "passes test; field strength ", "good", "fair", ".\n");
         break;
       default:
         SERIAL_ECHOLNPGM("not detected!");

Marlin/src/feature/I2CPositionEncoder.h

@@ -276,7 +276,7 @@ class I2CPositionEncodersMgr {
       CHECK_IDX();
       encoders[idx].set_ec_enabled(enabled);
       SERIAL_ECHOPAIR("Error correction on ", axis_codes[axis]);
-      serial_ternary(encoders[idx].get_ec_enabled(), PSTR(" axis is "), PSTR("en"), PSTR("dis"), PSTR("abled.\n"));
+      SERIAL_ECHO_TERNARY(encoders[idx].get_ec_enabled(), " axis is ", "en", "dis", "abled.\n");
     }
 
     static void set_ec_threshold(const int8_t idx, const float newThreshold, const AxisEnum axis) {

Marlin/src/feature/bedlevel/ubl/ubl.cpp

@@ -58,7 +58,7 @@
 
   void unified_bed_leveling::report_state() {
     echo_name();
-    serial_ternary(planner.leveling_active, PSTR(" System v" UBL_VERSION " "), PSTR(""), PSTR("in"), PSTR("active\n"));
+    SERIAL_ECHO_TERNARY(planner.leveling_active, " System v" UBL_VERSION " ", "", "in", "active\n");
     serial_delay(50);
   }
 

Marlin/src/feature/joystick.cpp

@@ -0,0 +1,151 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * joystick.cpp - joystick input / jogging
+ */
+
+#include "../inc/MarlinConfigPre.h"
+
+#if ENABLED(JOYSTICK)
+
+#include "joystick.h"
+
+#include "../inc/MarlinConfig.h"  // for pins
+#include "../module/planner.h"
+#include "../module/temperature.h"
+
+Joystick joystick;
+
+#if HAS_JOY_ADC_X
+  temp_info_t Joystick::x; // = { 0 }
+#endif
+#if HAS_JOY_ADC_Y
+  temp_info_t Joystick::y; // = { 0 }
+#endif
+#if HAS_JOY_ADC_Z
+  temp_info_t Joystick::z; // = { 0 }
+#endif
+
+#if ENABLED(JOYSTICK_DEBUG)
+  void Joystick::report() {
+    SERIAL_ECHOPGM("Joystick");
+    #if HAS_JOY_ADC_X
+      SERIAL_ECHOPAIR(" X", x.raw);
+    #endif
+    #if HAS_JOY_ADC_Y
+      SERIAL_ECHOPAIR(" Y", y.raw);
+    #endif
+    #if HAS_JOY_ADC_Z
+      SERIAL_ECHOPAIR(" Z", z.raw);
+    #endif
+    #if HAS_JOY_ADC_EN
+      SERIAL_ECHO_TERNARY(READ(JOY_EN_PIN), " EN=", "HIGH (dis", "LOW (en", "abled)");
+    #endif
+    SERIAL_EOL();
+  }
+#endif
+
+void Joystick::calculate(float norm_jog[XYZ]) {
+  // Do nothing if enable pin (active-low) is not LOW
+  #if HAS_JOY_ADC_EN
+    if (READ(JOY_EN_PIN)) return;
+  #endif
+
+  auto _normalize_joy = [](float &adc, const int16_t raw, const int16_t (&joy_limits)[4]) {
+    if (WITHIN(raw, joy_limits[0], joy_limits[3])) {
+      // within limits, check deadzone
+      if (raw > joy_limits[2])
+        adc = (raw - joy_limits[2]) / float(joy_limits[3] - joy_limits[2]);
+      else if (raw < joy_limits[1])
+        adc = (raw - joy_limits[1]) / float(joy_limits[1] - joy_limits[0]);  // negative value
+    }
+  };
+
+  #if HAS_JOY_ADC_X
+    static constexpr int16_t joy_x_limits[4] = JOY_X_LIMITS;
+    _normalize_joy(norm_jog[X_AXIS], x.raw, joy_x_limits);
+  #endif
+  #if HAS_JOY_ADC_Y
+    static constexpr int16_t joy_y_limits[4] = JOY_Y_LIMITS;
+    _normalize_joy(norm_jog[Y_AXIS], y.raw, joy_y_limits);
+  #endif
+  #if HAS_JOY_ADC_Z
+    static constexpr int16_t joy_z_limits[4] = JOY_Z_LIMITS;
+    _normalize_joy(norm_jog[Z_AXIS], z.raw, joy_z_limits);
+  #endif
+}
+
+#if ENABLED(POLL_JOG)
+
+  void Joystick::inject_jog_moves() {
+    // Recursion barrier
+    static bool injecting_now; // = false;
+    if (injecting_now) return;
+
+    static constexpr int QUEUE_DEPTH = 5;                                 // Insert up to this many movements
+    static constexpr float target_lag = 0.25f,                            // Aim for 1/4 second lag
+                           seg_time = target_lag / QUEUE_DEPTH;           // 0.05 seconds, short segments inserted every 1/20th of a second
+    static constexpr millis_t timer_limit_ms = millis_t(seg_time * 500);  // 25 ms minimum delay between insertions
+
+    // The planner can merge/collapse small moves, so the movement queue is unreliable to control the lag
+    static millis_t next_run = 0;
+    if (PENDING(millis(), next_run)) return;
+    next_run = millis() + timer_limit_ms;
+
+    // Only inject a command if the planner has fewer than 5 moves and there are no unparsed commands
+    if (planner.movesplanned() >= QUEUE_DEPTH || queue.has_commands_queued())
+      return;
+
+    // Normalized jog values are 0 for no movement and -1 or +1 for as max feedrate (nonlinear relationship)
+    // Jog are initialized to zero and handling input can update values but doesn't have to
+    // You could use a two-axis joystick and a one-axis keypad and they might work together
+    float norm_jog[XYZ] = { 0 };
+
+    // Use ADC values and defined limits. The active zone is normalized: -1..0 (dead) 0..1
+    joystick.calculate(norm_jog);
+
+    // Other non-joystick poll-based jogging could be implemented here
+    // with "jogging" encapsulated as a more general class.
+
+    // Jogging value maps continuously (quadratic relationship) to feedrate
+    float move_dist[XYZ] = { 0 }, hypot2 = 0;
+    LOOP_XYZ(i) if (norm_jog[i]) {
+      move_dist[i] = seg_time * sq(norm_jog[i]) * planner.settings.max_feedrate_mm_s[i];
+      // Very small movements disappear when printed as decimal with 4 digits of precision
+      NOLESS(move_dist[i], 0.0002f);
+      if (norm_jog[i] < 0) move_dist[i] *= -1;  // preserve sign
+      hypot2 += sq(move_dist[i]);
+    }
+
+    if (!UNEAR_ZERO(hypot2)) {
+      LOOP_XYZ(i) current_position[i] += move_dist[i];
+      const float length = sqrt(hypot2);
+      injecting_now = true;
+      planner.buffer_line(current_position, length / seg_time, active_extruder, length);
+      injecting_now = false;
+    }
+  }
+
+#endif // POLL_JOG
+
+#endif // JOYSTICK

Marlin/src/feature/joystick.h

@@ -0,0 +1,53 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+/**
+ * joystick.h - joystick input / jogging
+ */
+
+#include "../core/macros.h"
+#include "../module/temperature.h"
+
+//#define JOYSTICK_DEBUG
+
+class Joystick {
+  friend class Temperature;
+  private:
+    #if HAS_JOY_ADC_X
+      static temp_info_t x;
+    #endif
+    #if HAS_JOY_ADC_Y
+      static temp_info_t y;
+    #endif
+    #if HAS_JOY_ADC_Z
+      static temp_info_t z;
+    #endif
+  public:
+    #if ENABLED(JOYSTICK_DEBUG)
+      static void report();
+    #endif
+    static void calculate(float norm_jog[XYZ]);
+    static void inject_jog_moves();
+};
+
+extern Joystick joystick;

Marlin/src/gcode/parser.h

@@ -263,13 +263,9 @@ public:
 
     static inline void set_input_linear_units(const LinearUnit units) {
       switch (units) {
-        case LINEARUNIT_INCH:
-          linear_unit_factor = 25.4f;
-          break;
-        case LINEARUNIT_MM:
         default:
-          linear_unit_factor = 1;
+        case LINEARUNIT_MM:   linear_unit_factor =  1.0f; break;
-          break;
+        case LINEARUNIT_INCH: linear_unit_factor = 25.4f; break;
       }
       volumetric_unit_factor = POW(linear_unit_factor, 3);
     }

Marlin/src/inc/Conditionals_adv.h

@@ -105,3 +105,8 @@
 
 // TMC SPI Chaining
 #define TMC_USE_CHAIN (X_CHAIN_POS||Y_CHAIN_POS||Z_CHAIN_POS||X2_CHAIN_POS||Y2_CHAIN_POS||Z2_CHAIN_POS||Z3_CHAIN_POS||E0_CHAIN_POS||E1_CHAIN_POS||E2_CHAIN_POS||E3_CHAIN_POS||E4_CHAIN_POS||E5_CHAIN_POS)
+
+// Poll-based jogging for joystick and other devices
+#if ENABLED(JOYSTICK)
+  #define POLL_JOG
+#endif

Marlin/src/inc/Conditionals_post.h

@@ -1026,6 +1026,13 @@
 #define HAS_TEMP_CHAMBER HAS_TEMP_ADC_CHAMBER
 #define HAS_HEATED_CHAMBER (HAS_TEMP_CHAMBER && PIN_EXISTS(HEATER_CHAMBER))
 
+#if ENABLED(JOYSTICK)
+  #define HAS_JOY_ADC_X  PIN_EXISTS(JOY_X)
+  #define HAS_JOY_ADC_Y  PIN_EXISTS(JOY_Y)
+  #define HAS_JOY_ADC_Z  PIN_EXISTS(JOY_Z)
+  #define HAS_JOY_ADC_EN PIN_EXISTS(JOY_EN)
+#endif
+
 // Heaters
 #define HAS_HEATER_0 (PIN_EXISTS(HEATER_0))
 #define HAS_HEATER_1 (PIN_EXISTS(HEATER_1))

Marlin/src/module/endstops.cpp

@@ -44,6 +44,10 @@
   #include "../feature/bltouch.h"
 #endif
 
+#if ENABLED(JOYSTICK)
+  #include "../feature/joystick.h"
+#endif
+
 Endstops endstops;
 
 // private:
@@ -474,6 +478,11 @@ void _O2 Endstops::M119() {
   #if ENABLED(BLTOUCH)
     bltouch._reset_SW_mode();
   #endif
+
+  #if ENABLED(JOYSTICK_DEBUG)
+    joystick.report();
+  #endif
+
 } // Endstops::M119
 
 // The following routines are called from an ISR context. It could be the temperature ISR, the

Marlin/src/module/temperature.cpp

@@ -64,6 +64,10 @@
   #include "../feature/leds/printer_event_leds.h"
 #endif
 
+#if ENABLED(JOYSTICK)
+  #include "../feature/joystick.h"
+#endif
+
 #if ENABLED(SINGLENOZZLE)
   #include "tool_change.h"
 #endif
@@ -1685,6 +1689,18 @@ void Temperature::init() {
   #if HAS_TEMP_ADC_5
     HAL_ANALOG_SELECT(TEMP_5_PIN);
   #endif
+  #if HAS_JOY_ADC_X
+    HAL_ANALOG_SELECT(JOY_X_PIN);
+  #endif
+  #if HAS_JOY_ADC_Y
+    HAL_ANALOG_SELECT(JOY_Y_PIN);
+  #endif
+  #if HAS_JOY_ADC_Z
+    HAL_ANALOG_SELECT(JOY_Z_PIN);
+  #endif
+  #if HAS_JOY_ADC_EN
+    SET_INPUT_PULLUP(JOY_EN_PIN);
+  #endif
   #if HAS_HEATED_BED
     HAL_ANALOG_SELECT(TEMP_BED_PIN);
   #endif
@@ -2195,6 +2211,16 @@ void Temperature::set_current_temp_raw() {
     temp_chamber.update();
   #endif
 
+  #if HAS_JOY_ADC_X
+    joystick.x.update();
+  #endif
+  #if HAS_JOY_ADC_Y
+    joystick.y.update();
+  #endif
+  #if HAS_JOY_ADC_Z
+    joystick.z.update();
+  #endif
+
   temp_meas_ready = true;
 }
 
@@ -2225,6 +2251,16 @@ void Temperature::readings_ready() {
     temp_chamber.reset();
   #endif
 
+  #if HAS_JOY_ADC_X
+    joystick.x.reset();
+  #endif
+  #if HAS_JOY_ADC_Y
+    joystick.y.reset();
+  #endif
+  #if HAS_JOY_ADC_Z
+    joystick.z.reset();
+  #endif
+
   static constexpr int8_t temp_dir[] = {
     #if ENABLED(HEATER_0_USES_MAX6675)
       0
@@ -2721,6 +2757,21 @@ void Temperature::isr() {
       break;
     #endif
 
+    #if HAS_JOY_ADC_X
+      case PrepareJoy_X: HAL_START_ADC(JOY_X_PIN); break;
+      case MeasureJoy_X: ACCUMULATE_ADC(joystick.x); break;
+    #endif
+
+    #if HAS_JOY_ADC_Y
+      case PrepareJoy_Y: HAL_START_ADC(JOY_Y_PIN); break;
+      case MeasureJoy_Y: ACCUMULATE_ADC(joystick.y); break;
+    #endif
+
+    #if HAS_JOY_ADC_Z
+      case PrepareJoy_Z: HAL_START_ADC(JOY_Z_PIN); break;
+      case MeasureJoy_Z: ACCUMULATE_ADC(joystick.z); break;
+    #endif
+
     #if HAS_ADC_BUTTONS
       case Prepare_ADC_KEY: HAL_START_ADC(ADC_KEYPAD_PIN); break;
       case Measure_ADC_KEY:

Marlin/src/module/temperature.h

@@ -92,44 +92,43 @@ typedef struct { float Kp, Ki, Kd, Kc; } PIDC_t;
 enum ADCSensorState : char {
   StartSampling,
   #if HAS_TEMP_ADC_0
-    PrepareTemp_0,
+    PrepareTemp_0, MeasureTemp_0,
-    MeasureTemp_0,
   #endif
   #if HAS_HEATED_BED
-    PrepareTemp_BED,
+    PrepareTemp_BED, MeasureTemp_BED,
-    MeasureTemp_BED,
   #endif
   #if HAS_TEMP_CHAMBER
-    PrepareTemp_CHAMBER,
+    PrepareTemp_CHAMBER, MeasureTemp_CHAMBER,
-    MeasureTemp_CHAMBER,
   #endif
   #if HAS_TEMP_ADC_1
-    PrepareTemp_1,
+    PrepareTemp_1, MeasureTemp_1,
-    MeasureTemp_1,
   #endif
   #if HAS_TEMP_ADC_2
-    PrepareTemp_2,
+    PrepareTemp_2, MeasureTemp_2,
-    MeasureTemp_2,
   #endif
   #if HAS_TEMP_ADC_3
-    PrepareTemp_3,
+    PrepareTemp_3, MeasureTemp_3,
-    MeasureTemp_3,
   #endif
   #if HAS_TEMP_ADC_4
-    PrepareTemp_4,
+    PrepareTemp_4, MeasureTemp_4,
-    MeasureTemp_4,
   #endif
   #if HAS_TEMP_ADC_5
-    PrepareTemp_5,
+    PrepareTemp_5, MeasureTemp_5,
-    MeasureTemp_5,
+  #endif
+  #if HAS_JOY_ADC_X
+    PrepareJoy_X, MeasureJoy_X,
+  #endif
+  #if HAS_JOY_ADC_Y
+    PrepareJoy_Y, MeasureJoy_Y,
+  #endif
+  #if HAS_JOY_ADC_Z
+    PrepareJoy_Z, MeasureJoy_Z,
   #endif
   #if ENABLED(FILAMENT_WIDTH_SENSOR)
-    Prepare_FILWIDTH,
+    Prepare_FILWIDTH, Measure_FILWIDTH,
-    Measure_FILWIDTH,
   #endif
   #if HAS_ADC_BUTTONS
-    Prepare_ADC_KEY,
+    Prepare_ADC_KEY, Measure_ADC_KEY,
-    Measure_ADC_KEY,
   #endif
   SensorsReady, // Temperatures ready. Delay the next round of readings to let ADC pins settle.
   StartupDelay  // Startup, delay initial temp reading a tiny bit so the hardware can settle

buildroot/share/tests/megaatmega2560-tests

@@ -79,7 +79,7 @@ restore_configs
 opt_enable ZONESTAR_LCD Z_PROBE_SERVO_NR Z_SERVO_ANGLES DEACTIVATE_SERVOS_AFTER_MOVE \
            AUTO_BED_LEVELING_3POINT DEBUG_LEVELING_FEATURE EEPROM_SETTINGS EEPROM_CHITCHAT
 opt_set NUM_SERVOS 1
-opt_enable NO_VOLUMETRICS EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES AUTOTEMP G38_PROBE_TARGET
+opt_enable NO_VOLUMETRICS EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES AUTOTEMP G38_PROBE_TARGET JOYSTICK
 exec_test $1 $2 "RAMPS with ZONESTAR_LCD, Servo Probe, 3-Point ABL, DEBUG_LEVELING_FEATURE, EEPROM, G38, and more"
 
 #

config/default/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/ADIMLab/Gantry v1/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/ADIMLab/Gantry v2/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Alfawise/U20-bltouch/Configuration_adv.h

@@ -2467,10 +2467,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2551,6 +2547,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Alfawise/U20/Configuration_adv.h

@@ -2466,10 +2466,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2550,6 +2546,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Anet/A2/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Anet/A2plus/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Anet/A6/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Anet/A8/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Anet/A8plus/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Anet/E16/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   #define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/ArmEd/Configuration_adv.h

@@ -2466,10 +2466,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2550,6 +2546,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -2470,10 +2470,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2554,6 +2550,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Cartesio/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Creality/CR-10/Configuration_adv.h

@@ -2465,10 +2465,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2549,6 +2545,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Creality/CR-10S/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Creality/CR-10_5S/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Creality/CR-20 Pro/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Creality/CR-20/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Creality/CR-8/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Creality/Ender-3/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Creality/Ender-4/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Creality/Ender-5/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Dagoma/Disco Ultimate/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   #define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Einstart-S/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/FYSETC/AIO_II/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/FYSETC/Cheetah/base/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/FYSETC/F6_13/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Felix/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/FlashForge/CreatorPro/Configuration_adv.h

@@ -2461,10 +2461,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2545,6 +2541,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -2466,10 +2466,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2550,6 +2546,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

@@ -2466,10 +2466,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2550,6 +2546,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -2461,10 +2461,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2545,6 +2541,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Geeetech/A10/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Geeetech/A10M/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Geeetech/A20M/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -2461,10 +2461,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2545,6 +2541,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/HMS434/Configuration_adv.h

@@ -2384,10 +2384,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2468,6 +2464,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/JGAurora/A1/Configuration_adv.h

@@ -2467,10 +2467,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2551,6 +2547,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/JGAurora/A5/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/JGAurora/A5S/Configuration_adv.h

@@ -2467,10 +2467,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2551,6 +2547,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/MakerParts/Configuration_adv.h

@@ -2455,10 +2455,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2539,6 +2535,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Malyan/M150/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Malyan/M200/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Mks/Robin/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Mks/Sbase/Configuration_adv.h

@@ -2463,10 +2463,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2547,6 +2543,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/RapideLite/RL200/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/RigidBot/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/SCARA/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Sanguinololu/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Tevo/Michelangelo/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Tevo/Tarantula Pro/Configuration_adv.h

@@ -2458,10 +2458,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2542,6 +2538,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/TheBorg/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/TinyBoy2/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Tronxy/X3A/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Tronxy/X5S-2E/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/UltiMachine/Archim1/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/VORONDesign/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Velleman/K8200/Configuration_adv.h

@@ -2475,10 +2475,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2559,6 +2555,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Velleman/K8400/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/WASP/PowerWASP/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Wanhao/Duplicator 6/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/Anycubic/Kossel/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/Dreammaker/Overlord/Configuration_adv.h

@@ -2452,10 +2452,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2536,6 +2532,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h

@@ -2452,10 +2452,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2536,6 +2532,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/FLSUN/kossel/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/MKS/SBASE/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/Tevo Little Monster/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/generic/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/kossel_mini/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/delta/kossel_xl/Configuration_adv.h

@@ -2464,10 +2464,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2548,6 +2544,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/makibox/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/tvrrug/Round2/Configuration_adv.h

@@ -2462,10 +2462,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2546,6 +2542,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *

config/examples/wt150/Configuration_adv.h

@@ -2463,10 +2463,6 @@
   //#define HOST_PROMPT_SUPPORT
 #endif
 
-//===========================================================================
-//====================== I2C Position Encoder Settings ======================
-//===========================================================================
-
 /**
  * I2C position encoders for closed loop control.
  * Developed by Chris Barr at Aus3D.
@@ -2547,6 +2543,22 @@
 
 #endif // I2C_POSITION_ENCODERS
 
+/**
+ * Analog Joystick(s)
+ */
+//#define JOYSTICK
+#if ENABLED(JOYSTICK)
+  #define JOY_X_PIN    5  // RAMPS: Suggested pin A5  on AUX2
+  #define JOY_Y_PIN   10  // RAMPS: Suggested pin A10 on AUX2
+  #define JOY_Z_PIN   12  // RAMPS: Suggested pin A12 on AUX2
+  #define JOY_EN_PIN  44  // RAMPS: Suggested pin D44 on AUX2
+
+  // Use M119 to find reasonable values after connecting your hardware:
+  #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max
+  #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 }
+  #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 }
+#endif
+
 /**
  * MAX7219 Debug Matrix
  *