diff --git a/Marlin/Conditionals.h b/Marlin/Conditionals.h index 3861f1301..d8d436496 100644 --- a/Marlin/Conditionals.h +++ b/Marlin/Conditionals.h @@ -371,6 +371,15 @@ #define MAX_PROBE_X (min(X_MAX_POS, X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER)) #define MIN_PROBE_Y (max(Y_MIN_POS, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) #define MAX_PROBE_Y (min(Y_MAX_POS, Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) + + #ifndef XY_TRAVEL_SPEED + #ifdef HOMING_FEEDRATE_XYZ + #define XY_TRAVEL_SPEED HOMING_FEEDRATE_XYZ + #else + #define XY_TRAVEL_SPEED 4000 + #endif + #endif + #endif #define HAS_Z_SERVO_ENDSTOP (defined(Z_ENDSTOP_SERVO_NR) && Z_ENDSTOP_SERVO_NR >= 0) @@ -758,7 +767,7 @@ #define HAS_BED_PROBE (PROBE_SELECTED && PROBE_PIN_CONFIGURED) /** - * Probe dependencies + * Bed Probe dependencies */ #if HAS_BED_PROBE #ifndef X_PROBE_OFFSET_FROM_EXTRUDER diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 05916e4ef..11aece9a2 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -409,6 +409,57 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // @@ -453,12 +504,20 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -606,27 +665,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -634,26 +672,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1147,14 +1165,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp index e726bd0ca..afde4784d 100644 --- a/Marlin/Marlin_main.cpp +++ b/Marlin/Marlin_main.cpp @@ -1575,7 +1575,7 @@ static void setup_for_endstop_move() { endstops.enable(); } -#if ENABLED(AUTO_BED_LEVELING_FEATURE) +#if HAS_BED_PROBE #if ENABLED(DELTA) /** @@ -1592,6 +1592,71 @@ static void setup_for_endstop_move() { } #endif + /** + * Plan a move to (X, Y, Z) and set the current_position + * The final current_position may not be the one that was requested + */ + static void do_blocking_move_to(float x, float y, float z) { + float old_feedrate = feedrate; + + #if ENABLED(DEBUG_LEVELING_FEATURE) + if (DEBUGGING(LEVELING)) print_xyz("do_blocking_move_to", x, y, z); + #endif + + #if ENABLED(DELTA) + + feedrate = + #if ENABLED(AUTO_BED_LEVELING_FEATURE) + xy_travel_speed + #else + min(planner.max_feedrate[X_AXIS], planner.max_feedrate[Y_AXIS]) * 60 + #endif + ; + + destination[X_AXIS] = x; + destination[Y_AXIS] = y; + destination[Z_AXIS] = z; + + if (x == current_position[X_AXIS] && y == current_position[Y_AXIS]) + prepare_move_to_destination_raw(); // this will also set_current_to_destination + else + prepare_move_to_destination(); // this will also set_current_to_destination + + #else + + feedrate = homing_feedrate[Z_AXIS]; + + current_position[Z_AXIS] = z; + line_to_current_position(); + stepper.synchronize(); + + feedrate = + #if ENABLED(AUTO_BED_LEVELING_FEATURE) + xy_travel_speed + #else + min(planner.max_feedrate[X_AXIS], planner.max_feedrate[Y_AXIS]) * 60 + #endif + ; + + current_position[X_AXIS] = x; + current_position[Y_AXIS] = y; + line_to_current_position(); + + #endif + + stepper.synchronize(); + + feedrate = old_feedrate; + } + + inline void do_blocking_move_to_z(float z) { + do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], z); + } + +#endif //HAS_BED_PROBE + +#if ENABLED(AUTO_BED_LEVELING_FEATURE) + #if ENABLED(AUTO_BED_LEVELING_GRID) #if DISABLED(DELTA) @@ -1751,51 +1816,6 @@ static void setup_for_endstop_move() { feedrate = old_feedrate; } - /** - * Plan a move to (X, Y, Z) and set the current_position - * The final current_position may not be the one that was requested - */ - static void do_blocking_move_to(float x, float y, float z) { - float old_feedrate = feedrate; - - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) print_xyz("do_blocking_move_to", x, y, z); - #endif - - #if ENABLED(DELTA) - - feedrate = xy_travel_speed; - - destination[X_AXIS] = x; - destination[Y_AXIS] = y; - destination[Z_AXIS] = z; - - if (x == current_position[X_AXIS] && y == current_position[Y_AXIS]) - prepare_move_to_destination_raw(); // this will also set_current_to_destination - else - prepare_move_to_destination(); // this will also set_current_to_destination - - #else - - feedrate = homing_feedrate[Z_AXIS]; - - current_position[Z_AXIS] = z; - line_to_current_position(); - stepper.synchronize(); - - feedrate = xy_travel_speed; - - current_position[X_AXIS] = x; - current_position[Y_AXIS] = y; - line_to_current_position(); - - #endif - - stepper.synchronize(); - - feedrate = old_feedrate; - } - inline void do_blocking_move_to_xy(float x, float y) { do_blocking_move_to(x, y, current_position[Z_AXIS]); } @@ -1804,10 +1824,6 @@ static void setup_for_endstop_move() { do_blocking_move_to(x, current_position[Y_AXIS], current_position[Z_AXIS]); } - inline void do_blocking_move_to_z(float z) { - do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], z); - } - inline void raise_z_after_probing() { #if Z_RAISE_AFTER_PROBING > 0 #if ENABLED(DEBUG_LEVELING_FEATURE) @@ -2171,31 +2187,31 @@ static void setup_for_endstop_move() { #endif // DELTA - #if HAS_Z_SERVO_ENDSTOP - - /** - * Raise Z to a minimum height to make room for a servo to move - * - * zprobe_zoffset: Negative of the Z height where the probe engages - * z_dest: The before / after probing raise distance - * - * The zprobe_zoffset is negative for a switch below the nozzle, so - * multiply by Z_HOME_DIR (-1) to move enough away from the bed. - */ - void raise_z_for_servo(float z_dest) { - z_dest += home_offset[Z_AXIS]; - - if ((Z_HOME_DIR) < 0 && zprobe_zoffset < 0) - z_dest -= zprobe_zoffset; - - if (z_dest > current_position[Z_AXIS]) - do_blocking_move_to_z(z_dest); // also updates current_position - } - - #endif - #endif // AUTO_BED_LEVELING_FEATURE +#if HAS_Z_SERVO_ENDSTOP + + /** + * Raise Z to a minimum height to make room for a servo to move + * + * zprobe_zoffset: Negative of the Z height where the probe engages + * z_dest: The before / after probing raise distance + * + * The zprobe_zoffset is negative for a switch below the nozzle, so + * multiply by Z_HOME_DIR (-1) to move enough away from the bed. + */ + void raise_z_for_servo(float z_dest) { + z_dest += home_offset[Z_AXIS]; + + if ((Z_HOME_DIR) < 0 && zprobe_zoffset < 0) + z_dest -= zprobe_zoffset; + + if (z_dest > current_position[Z_AXIS]) + do_blocking_move_to_z(z_dest); // also updates current_position + } + +#endif + #if ENABLED(Z_PROBE_SLED) || ENABLED(Z_SAFE_HOMING) || ENABLED(AUTO_BED_LEVELING_FEATURE) static void axis_unhomed_error(bool xyz=false) { if (xyz) { diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h index bc3bf650b..1f0543f10 100644 --- a/Marlin/SanityCheck.h +++ b/Marlin/SanityCheck.h @@ -420,10 +420,14 @@ #endif /** - * Allen Key Z probe requires Auto Bed Leveling grid and Delta + * Allen Key Z probe requires Delta and Auto Bed Leveling grid */ -#if ENABLED(Z_PROBE_ALLEN_KEY) && !(ENABLED(AUTO_BED_LEVELING_GRID) && ENABLED(DELTA)) - #error "Invalid use of Z_PROBE_ALLEN_KEY." +#if ENABLED(Z_PROBE_ALLEN_KEY) + #if !ENABLED(DELTA) + #error "Z_PROBE_ALLEN_KEY is only usable with DELTA." + #elif ENABLED(MESH_BED_LEVELING) || (ENABLED(AUTO_BED_LEVELING_FEATURE) && !ENABLED(AUTO_BED_LEVELING_GRID)) + #error "Z_PROBE_ALLEN_KEY can only use AUTO_BED_LEVELING_GRID leveling." + #endif #endif /** diff --git a/Marlin/example_configurations/Cartesio/Configuration.h b/Marlin/example_configurations/Cartesio/Configuration.h index 95e9f26b1..59bae3aef 100644 --- a/Marlin/example_configurations/Cartesio/Configuration.h +++ b/Marlin/example_configurations/Cartesio/Configuration.h @@ -408,6 +408,57 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //============================= Z Probe Options ============================= //=========================================================================== +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // @@ -452,12 +503,20 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 1 @@ -605,27 +664,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -633,26 +671,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1150,14 +1168,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index 77b02a153..35f9ebb2a 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -435,12 +435,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -588,27 +647,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -616,25 +654,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1130,14 +1149,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h index 7d3ef3dde..65246a501 100644 --- a/Marlin/example_configurations/Felix/DUAL/Configuration.h +++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h @@ -433,12 +433,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -586,27 +645,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -614,25 +652,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1128,14 +1147,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index 39ee26f14..f9fedfbd2 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -445,12 +445,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -598,27 +657,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -626,25 +664,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1139,14 +1158,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h index 431c51172..59b5eb610 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration.h @@ -447,12 +447,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER 34 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 15 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 5 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 5 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -600,27 +659,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER 34 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER 15 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 2 // How much the Z axis will be raised when traveling from between next probing points. @@ -628,26 +666,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - #define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1146,14 +1164,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index e12f0993f..3907e4184 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -470,12 +470,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -623,27 +682,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -651,25 +689,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1164,14 +1183,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index 416d6ac00..453cfe75c 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -453,12 +453,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -606,27 +665,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -634,25 +672,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1147,14 +1166,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index b66f641ed..9057a9e86 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -447,12 +447,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -600,27 +659,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -628,25 +666,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1144,14 +1163,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // #define NUM_SERVOS 0 // DGlass3D - Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 3fd2d26ef..70c297292 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -461,12 +461,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -614,27 +673,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -642,25 +680,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1155,14 +1174,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index b1c3763d1..fc5c49ec2 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -474,12 +474,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -627,27 +686,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -655,25 +693,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1168,14 +1187,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index 28db20cdf..f5dfa6d36 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -445,12 +445,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -598,27 +657,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -626,25 +664,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1139,14 +1158,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index 9cfa2aba3..d83749fc1 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -453,12 +453,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -606,27 +665,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -634,25 +672,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1147,14 +1166,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h index 5ff3a53ca..df66fd5b7 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h @@ -495,12 +495,108 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] + +// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe +// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. +//#define Z_PROBE_ALLEN_KEY + +#if ENABLED(Z_PROBE_ALLEN_KEY) + // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, + // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. + + // Just like Kossel Pro + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X -105.00 // Move left but not quite so far that we'll bump the belt + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y 0.00 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_TRAVEL_SPEED + + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X -110.00 // Move outward to position deploy pin to the left of the arm + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y -125.00 + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE XY_TRAVEL_SPEED + + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X 45.00 // Move right to trigger deploy pin + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y -125.00 + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE (XY_TRAVEL_SPEED)/2 + + #define Z_PROBE_ALLEN_KEY_STOW_1_X 36.00 // Line up with bed retaining clip + #define Z_PROBE_ALLEN_KEY_STOW_1_Y -122.00 + #define Z_PROBE_ALLEN_KEY_STOW_1_Z 75.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_TRAVEL_SPEED + + #define Z_PROBE_ALLEN_KEY_STOW_2_X 36.00 // move down to retract probe + #define Z_PROBE_ALLEN_KEY_STOW_2_Y -122.00 + #define Z_PROBE_ALLEN_KEY_STOW_2_Z 25.0 + #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_TRAVEL_SPEED)/2 + + #define Z_PROBE_ALLEN_KEY_STOW_3_X 0.0 // return to 0,0,100 + #define Z_PROBE_ALLEN_KEY_STOW_3_Y 0.0 + #define Z_PROBE_ALLEN_KEY_STOW_3_Z 100.0 + #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_TRAVEL_SPEED + +#endif // Z_PROBE_ALLEN_KEY + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 50 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -652,27 +748,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 4000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -680,67 +755,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE - - // Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe - // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. - //#define Z_PROBE_ALLEN_KEY - - #if ENABLED(Z_PROBE_ALLEN_KEY) - // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, - // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. - - // Just like Kossel Pro - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X -105.00 // Move left but not quite so far that we'll bump the belt - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y 0.00 - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE HOMING_FEEDRATE_XYZ - - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X -110.00 // Move outward to position deploy pin to the left of the arm - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y -125.00 - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE HOMING_FEEDRATE_XYZ - - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X 45.00 // Move right to trigger deploy pin - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y -125.00 - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE (HOMING_FEEDRATE_XYZ)/2 - - #define Z_PROBE_ALLEN_KEY_STOW_1_X 36.00 // Line up with bed retaining clip - #define Z_PROBE_ALLEN_KEY_STOW_1_Y -122.00 - #define Z_PROBE_ALLEN_KEY_STOW_1_Z 75.0 - #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE HOMING_FEEDRATE_XYZ - - #define Z_PROBE_ALLEN_KEY_STOW_2_X 36.00 // move down to retract probe - #define Z_PROBE_ALLEN_KEY_STOW_2_Y -122.00 - #define Z_PROBE_ALLEN_KEY_STOW_2_Z 25.0 - #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (HOMING_FEEDRATE_XYZ)/2 - - #define Z_PROBE_ALLEN_KEY_STOW_3_X 0.0 // return to 0,0,100 - #define Z_PROBE_ALLEN_KEY_STOW_3_Y 0.0 - #define Z_PROBE_ALLEN_KEY_STOW_3_Z 100.0 - #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ - - #endif // Z_PROBE_ALLEN_KEY - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1236,14 +1250,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 8085cfcaf..f8837258d 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -495,12 +495,102 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] + +// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe +// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. +//#define Z_PROBE_ALLEN_KEY + +#if ENABLED(Z_PROBE_ALLEN_KEY) + // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, + // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. + + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_TRAVEL_SPEED + + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_TRAVEL_SPEED)/10 + + #define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 // Move the probe into position + #define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_TRAVEL_SPEED + + #define Z_PROBE_ALLEN_KEY_STOW_2_X -64.0 // Push it down + #define Z_PROBE_ALLEN_KEY_STOW_2_Y 56.0 + #define Z_PROBE_ALLEN_KEY_STOW_2_Z 3.0 + #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_TRAVEL_SPEED)/10 + + #define Z_PROBE_ALLEN_KEY_STOW_3_X -64.0 // Move it up to clear + #define Z_PROBE_ALLEN_KEY_STOW_3_Y 56.0 + #define Z_PROBE_ALLEN_KEY_STOW_3_Z 50.0 + #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_TRAVEL_SPEED + +#endif // Z_PROBE_ALLEN_KEY + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 50 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -652,27 +742,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 4000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points @@ -680,61 +749,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE - - // Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe - // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. - //#define Z_PROBE_ALLEN_KEY - - #if ENABLED(Z_PROBE_ALLEN_KEY) - // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, - // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. - - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE HOMING_FEEDRATE_XYZ - - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (HOMING_FEEDRATE_XYZ)/10 - - #define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 // Move the probe into position - #define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0 - #define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0 - #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE HOMING_FEEDRATE_XYZ - - #define Z_PROBE_ALLEN_KEY_STOW_2_X -64.0 // Push it down - #define Z_PROBE_ALLEN_KEY_STOW_2_Y 56.0 - #define Z_PROBE_ALLEN_KEY_STOW_2_Z 3.0 - #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (HOMING_FEEDRATE_XYZ)/10 - - #define Z_PROBE_ALLEN_KEY_STOW_3_X -64.0 // Move it up to clear - #define Z_PROBE_ALLEN_KEY_STOW_3_Y 56.0 - #define Z_PROBE_ALLEN_KEY_STOW_3_Z 50.0 - #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ - - #endif // Z_PROBE_ALLEN_KEY - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1230,14 +1244,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index a8a14bbe9..3bd6146d1 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -419,7 +419,7 @@ // extra connectors. Leave undefined any used for non-endstop and non-probe purposes. //#define USE_XMIN_PLUG //#define USE_YMIN_PLUG -//#define USE_ZMIN_PLUG +#define USE_ZMIN_PLUG #define USE_XMAX_PLUG #define USE_YMAX_PLUG #define USE_ZMAX_PLUG @@ -495,12 +495,105 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] + +// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe +// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. +#define Z_PROBE_ALLEN_KEY + +#if ENABLED(Z_PROBE_ALLEN_KEY) + // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, + // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. + + // Kossel Mini + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_TRAVEL_SPEED + + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_TRAVEL_SPEED/10) + + #define Z_PROBE_ALLEN_KEY_STOW_DEPTH 20 + // Move the probe into position + #define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_TRAVEL_SPEED + // Move the nozzle down further to push the probe into retracted position. + #define Z_PROBE_ALLEN_KEY_STOW_2_X Z_PROBE_ALLEN_KEY_STOW_1_X + #define Z_PROBE_ALLEN_KEY_STOW_2_Y Z_PROBE_ALLEN_KEY_STOW_1_Y + #define Z_PROBE_ALLEN_KEY_STOW_2_Z (Z_PROBE_ALLEN_KEY_STOW_1_Z-Z_PROBE_ALLEN_KEY_STOW_DEPTH) + #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_TRAVEL_SPEED/10) + // Raise things back up slightly so we don't bump into anything + #define Z_PROBE_ALLEN_KEY_STOW_3_X Z_PROBE_ALLEN_KEY_STOW_2_X + #define Z_PROBE_ALLEN_KEY_STOW_3_Y Z_PROBE_ALLEN_KEY_STOW_2_Y + #define Z_PROBE_ALLEN_KEY_STOW_3_Z (Z_PROBE_ALLEN_KEY_STOW_1_Z+Z_PROBE_ALLEN_KEY_STOW_DEPTH) + #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE (XY_TRAVEL_SPEED/2) + +#endif // Z_PROBE_ALLEN_KEY + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 50 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -652,27 +745,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 4000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points @@ -680,64 +752,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE - - // Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe - // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. - #define Z_PROBE_ALLEN_KEY - - #if ENABLED(Z_PROBE_ALLEN_KEY) - // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, - // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. - - // Kossel Mini - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_TRAVEL_SPEED - - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_TRAVEL_SPEED/10) - - #define Z_PROBE_ALLEN_KEY_STOW_DEPTH 20 - // Move the probe into position - #define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 - #define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0 - #define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0 - #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_TRAVEL_SPEED - // Move the nozzle down further to push the probe into retracted position. - #define Z_PROBE_ALLEN_KEY_STOW_2_X Z_PROBE_ALLEN_KEY_STOW_1_X - #define Z_PROBE_ALLEN_KEY_STOW_2_Y Z_PROBE_ALLEN_KEY_STOW_1_Y - #define Z_PROBE_ALLEN_KEY_STOW_2_Z (Z_PROBE_ALLEN_KEY_STOW_1_Z-Z_PROBE_ALLEN_KEY_STOW_DEPTH) - #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_TRAVEL_SPEED/10) - // Raise things back up slightly so we don't bump into anything - #define Z_PROBE_ALLEN_KEY_STOW_3_X Z_PROBE_ALLEN_KEY_STOW_2_X - #define Z_PROBE_ALLEN_KEY_STOW_3_Y Z_PROBE_ALLEN_KEY_STOW_2_Y - #define Z_PROBE_ALLEN_KEY_STOW_3_Z (Z_PROBE_ALLEN_KEY_STOW_1_Z+Z_PROBE_ALLEN_KEY_STOW_DEPTH) - #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE (XY_TRAVEL_SPEED/2) - - #endif // Z_PROBE_ALLEN_KEY - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1233,14 +1247,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index b66ddc65b..579324567 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -484,12 +484,110 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -23 // KosselPro actual: -22.919 +#define Y_PROBE_OFFSET_FROM_EXTRUDER -6 // KosselPro actual: -6.304 +// Kossel Pro note: The correct value is likely -17.45 but I'd rather err on the side of +// not giving someone a head crash. Use something like G29 Z-0.2 to adjust as needed. +#define Z_PROBE_OFFSET_FROM_EXTRUDER -17.25 // Increase this if the first layer is too thin (remember: it's a negative number so increase means closer to zero). + +// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe +// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. +#define Z_PROBE_ALLEN_KEY + +#if ENABLED(Z_PROBE_ALLEN_KEY) + // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, + // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. + + // Kossel Pro + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X -105.00 // Move left but not quite so far that we'll bump the belt + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y 0.00 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 + #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_TRAVEL_SPEED + + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X -110.00 // Move outward to position deploy pin to the left of the arm + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y -125.00 + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z Z_PROBE_ALLEN_KEY_DEPLOY_1_Z + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE XY_TRAVEL_SPEED + + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X 45.00 // Move right to trigger deploy pin + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y -125.00 + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z + #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE (XY_TRAVEL_SPEED)/2 + + #define Z_PROBE_ALLEN_KEY_STOW_1_X 36.00 // Line up with bed retaining clip + #define Z_PROBE_ALLEN_KEY_STOW_1_Y -125.00 + #define Z_PROBE_ALLEN_KEY_STOW_1_Z 75.0 + #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_TRAVEL_SPEED + + #define Z_PROBE_ALLEN_KEY_STOW_2_X Z_PROBE_ALLEN_KEY_STOW_1_X // move down to retract probe + #define Z_PROBE_ALLEN_KEY_STOW_2_Y Z_PROBE_ALLEN_KEY_STOW_1_Y + #define Z_PROBE_ALLEN_KEY_STOW_2_Z 0.0 + #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_TRAVEL_SPEED)/2 + + #define Z_PROBE_ALLEN_KEY_STOW_3_X 0.0 // return to 0,0,100 + #define Z_PROBE_ALLEN_KEY_STOW_3_Y 0.0 + #define Z_PROBE_ALLEN_KEY_STOW_3_Z 100.0 + #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_TRAVEL_SPEED + +#endif // Z_PROBE_ALLEN_KEY + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 100 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -641,29 +739,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -23 // KosselPro actual: -22.919 - #define Y_PROBE_OFFSET_FROM_EXTRUDER -6 // KosselPro actual: -6.304 - // Kossel Pro note: The correct value is likely -17.45 but I'd rather err on the side of - // not giving someone a head crash. Use something like G29 Z-0.2 to adjust as needed. - #define Z_PROBE_OFFSET_FROM_EXTRUDER -17.25 // Increase this if the first layer is too thin (remember: it's a negative number so increase means closer to zero). - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -671,67 +746,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE - - // Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe - // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. - #define Z_PROBE_ALLEN_KEY - - #if ENABLED(Z_PROBE_ALLEN_KEY) - // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, - // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. - - // Kossel Pro - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_X -105.00 // Move left but not quite so far that we'll bump the belt - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y 0.00 - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE HOMING_FEEDRATE_XYZ - - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X -110.00 // Move outward to position deploy pin to the left of the arm - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y -125.00 - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z Z_PROBE_ALLEN_KEY_DEPLOY_1_Z - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE HOMING_FEEDRATE_XYZ - - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X 45.00 // Move right to trigger deploy pin - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y -125.00 - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z - #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE (HOMING_FEEDRATE_XYZ)/2 - - #define Z_PROBE_ALLEN_KEY_STOW_1_X 36.00 // Line up with bed retaining clip - #define Z_PROBE_ALLEN_KEY_STOW_1_Y -125.00 - #define Z_PROBE_ALLEN_KEY_STOW_1_Z 75.0 - #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE HOMING_FEEDRATE_XYZ - - #define Z_PROBE_ALLEN_KEY_STOW_2_X Z_PROBE_ALLEN_KEY_STOW_1_X // move down to retract probe - #define Z_PROBE_ALLEN_KEY_STOW_2_Y Z_PROBE_ALLEN_KEY_STOW_1_Y - #define Z_PROBE_ALLEN_KEY_STOW_2_Z 0.0 - #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (HOMING_FEEDRATE_XYZ)/2 - - #define Z_PROBE_ALLEN_KEY_STOW_3_X 0.0 // return to 0,0,100 - #define Z_PROBE_ALLEN_KEY_STOW_3_Y 0.0 - #define Z_PROBE_ALLEN_KEY_STOW_3_Z 100.0 - #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ - - #endif // Z_PROBE_ALLEN_KEY - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1238,14 +1252,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h index b77e485a6..0d1d3a506 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h @@ -493,12 +493,102 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Z probe to nozzle X offset: -left +right +#define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Z probe to nozzle Y offset: -front +behind +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3 // Z probe to nozzle Z offset: -below (always!) + +// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe +// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. +//#define Z_PROBE_ALLEN_KEY + +#if ENABLED(Z_PROBE_ALLEN_KEY) + // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, + // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. + + //#define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0 + //#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS + //#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 + //#define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_TRAVEL_SPEED + + //#define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 + //#define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS + //#define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 + //#define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_TRAVEL_SPEED)/10 + + //#define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 // Move the probe into position + //#define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0 + //#define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0 + //#define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_TRAVEL_SPEED + + //#define Z_PROBE_ALLEN_KEY_STOW_2_X -64.0 // Push it down + //#define Z_PROBE_ALLEN_KEY_STOW_2_Y 56.0 + //#define Z_PROBE_ALLEN_KEY_STOW_2_Z 3.0 + //#define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_TRAVEL_SPEED)/10 + + //#define Z_PROBE_ALLEN_KEY_STOW_3_X -64.0 // Move it up to clear + //#define Z_PROBE_ALLEN_KEY_STOW_3_Y 56.0 + //#define Z_PROBE_ALLEN_KEY_STOW_3_Z 50.0 + //#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_TRAVEL_SPEED + +#endif // Z_PROBE_ALLEN_KEY + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 20 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 20 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -650,27 +740,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Z probe to nozzle X offset: -left +right - #define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Z probe to nozzle Y offset: -front +behind - #define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3 // Z probe to nozzle Z offset: -below (always!) - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 10 // How much the Z axis will be raised when traveling from between next probing points. @@ -678,61 +747,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - #define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE - - // Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe - // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. - //#define Z_PROBE_ALLEN_KEY - - #if ENABLED(Z_PROBE_ALLEN_KEY) - // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29, - // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe. - - //#define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0 - //#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS - //#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0 - //#define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE HOMING_FEEDRATE_XYZ - - //#define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 - //#define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS - //#define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 - //#define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (HOMING_FEEDRATE_XYZ)/10 - - //#define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 // Move the probe into position - //#define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0 - //#define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0 - //#define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE HOMING_FEEDRATE_XYZ - - //#define Z_PROBE_ALLEN_KEY_STOW_2_X -64.0 // Push it down - //#define Z_PROBE_ALLEN_KEY_STOW_2_Y 56.0 - //#define Z_PROBE_ALLEN_KEY_STOW_2_Z 3.0 - //#define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (HOMING_FEEDRATE_XYZ)/10 - - //#define Z_PROBE_ALLEN_KEY_STOW_3_X -64.0 // Move it up to clear - //#define Z_PROBE_ALLEN_KEY_STOW_3_Y 56.0 - //#define Z_PROBE_ALLEN_KEY_STOW_3_Z 50.0 - //#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ - - #endif // Z_PROBE_ALLEN_KEY - // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1235,14 +1249,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index dc51bddc2..6498d39df 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -456,12 +456,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 0 @@ -609,27 +668,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -637,25 +675,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1150,14 +1169,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter. diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index e84e1bf3b..b47bec944 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -443,12 +443,71 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // If you're using the Z MIN endstop connector for your Z probe, this has no effect. //#define DISABLE_Z_MIN_PROBE_ENDSTOP +// +// Probe Type +// Probes are sensors/switches that are activated / deactivated before/after use. +// +// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. +// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below. +// +// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500. +// + +// A fix mounted probe, like the normal inductive probe, must be deactivated to go +// below Z_PROBE_OFFSET_FROM_EXTRUDER when the hardware endstops are active. +//#define FIX_MOUNTED_PROBE + +// Z Servo Probe, such as an endstop switch on a rotating arm. +//#define Z_ENDSTOP_SERVO_NR 0 +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment +// For example any setup that uses the nozzle itself as a probe. +//#define MECHANICAL_PROBE + +// Z Probe to nozzle (X,Y) offset, relative to (0, 0). +// X and Y offsets must be integers. +// +// In the following example the X and Y offsets are both positive: +// #define X_PROBE_OFFSET_FROM_EXTRUDER 10 +// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 +// +// +-- BACK ---+ +// | | +// L | (+) P | R <-- probe (20,20) +// E | | I +// F | (-) N (+) | G <-- nozzle (10,10) +// T | | H +// | (-) | T +// | | +// O-- FRONT --+ +// (0,0) +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// +// Allen Key Probe is defined in the Delta example configurations. +// + +// // Probe Raise options provide clearance for the probe to deploy and stow. +// // For G28 these apply when the probe deploys and stows. // For G29 these apply before and after the full procedure. #define Z_RAISE_BEFORE_PROBING 15 // Raise before probe deploy (e.g., the first probe). #define Z_RAISE_AFTER_PROBING 15 // Raise before probe stow (e.g., the last probe). +// +// For M851 give a range for adjusting the Z probe offset +// +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{0:'Low',1:'High'} #define X_ENABLE_ON 1 @@ -596,27 +655,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo #endif // !AUTO_BED_LEVELING_GRID - // Z Probe to nozzle (X,Y) offset, relative to (0, 0). - // X and Y offsets must be integers. - // - // In the following example the X and Y offsets are both positive: - // #define X_PROBE_OFFSET_FROM_EXTRUDER 10 - // #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 - // - // +-- BACK ---+ - // | | - // L | (+) P | R <-- probe (20,20) - // E | | I - // F | (-) N (+) | G <-- nozzle (10,10) - // T | | H - // | (-) | T - // | | - // O-- FRONT --+ - // (0,0) - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define Z_RAISE_BETWEEN_PROBINGS 5 // How much the Z axis will be raised when traveling from between next probing points. @@ -624,25 +662,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - // Probes are sensors/switches that need to be activated before they can be used - // and deactivated after their use. - // Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, ... . You have to activate one of these for the AUTO_BED_LEVELING_FEATURE - - // A fix mounted probe, like the normal inductive probe, must be deactivated to go below Z_PROBE_OFFSET_FROM_EXTRUDER - // when the hardware endstops are active. - //#define FIX_MOUNTED_PROBE - - // A Servo Probe can be defined in the servo section below. - - // An Allen Key Probe is currently predefined only in the delta example configurations. - - // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. - //#define Z_PROBE_SLED - //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - // A Mechanical Probe is any probe that either doesn't deploy or needs manual deployment - // For example any setup that uses the nozzle itself as a probe. - //#define MECHANICAL_PROBE // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing, // it is highly recommended you also enable Z_SAFE_HOMING below! @@ -1141,14 +1160,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the Z probe vertical offset from the nozzle. Store that setting with M500. -// -//#define Z_ENDSTOP_SERVO_NR 0 -//#define Z_SERVO_ANGLES {70,0} // Z Servo Extend and Retract angles - // Servo deactivation // // With this option servos are powered only during movement, then turned off to prevent jitter.