More parity with 1.1.x, plus whitespace

This commit is contained in:
Scott Lahteine 2017-12-19 18:36:16 -06:00
parent a891d8d738
commit de5ca96654
8 changed files with 13 additions and 15 deletions

View file

@ -56,7 +56,7 @@
// If we could use 1.65A as motor current, then 3000 mm/s^2 as acceleration
// if perfectly achievable. Using 1A as motor current, 2400 mm/s^2 acceleration
// is perfectly possible without losing any steps
// On A4988 drivers, maximum current can be calculated as I_TripMax= Vref/(8*Rs)
// On A4988 drivers, maximum current can be calculated as I_TripMax= Vref/(8*Rs)
//
//===========================================================================
@ -548,14 +548,14 @@
* Override with M92
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,97} //motor bajos con varilla3200 y altos 1600 default steps per unit for Ultimaker
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 97 }
/**
* Default Max Feed Rate (mm/s)
* Override with M203
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 2, 30 } /* For 300mm/s printing */
#define DEFAULT_MAX_FEEDRATE { 300, 300, 2, 30 } // For 300mm/s printing
/**
* Default Max Acceleration (change/s) change = mm/s

View file

@ -65,8 +65,8 @@ class U8GLIB_ST7920_128X64_RRD : public U8GLIB
extern u8g_dev_t u8g_dev_st7920_128x64_custom_sw_spi;
class U8GLIB_ST7920_128X64_CUSTOM_SW_SPI : public U8GLIB {
public:
U8GLIB_ST7920_128X64_CUSTOM_SW_SPI()
: U8GLIB(&u8g_dev_st7920_128x64_custom_sw_spi)
U8GLIB_ST7920_128X64_CUSTOM_SW_SPI()
: U8GLIB(&u8g_dev_st7920_128x64_custom_sw_spi)
{ }
};

View file

@ -2559,10 +2559,8 @@ void kill_screen(const char* lcd_msg) {
lcd_bed_leveling
#endif
);
#else
#if PLANNER_LEVELING
MENU_ITEM(gcode, MSG_BED_LEVELING, PSTR("G28\nG29"));
#endif
#elif PLANNER_LEVELING && DISABLED(PROBE_MANUALLY)
MENU_ITEM(gcode, MSG_BED_LEVELING, PSTR("G28\nG29"));
#endif
#if ENABLED(LEVEL_BED_CORNERS) && DISABLED(LCD_BED_LEVELING)

View file

@ -172,7 +172,7 @@
#elif ENABLED(U8GLIB_ST7920) && defined(__arm__)
// RepRap Discount Full Graphics Smart Controller on an ARM target
U8GLIB_ST7920_128X64_CUSTOM_SW_SPI u8g;
#elif ENABLED(U8GLIB_ST7920)
// RepRap Discount Full Graphics Smart Controller
//U8GLIB_ST7920_128X64_4X u8g(LCD_PINS_RS); // 2 stripes, HW SPI (shared with SD card, on AVR does not use standard LCD adapter)
@ -180,7 +180,7 @@
U8GLIB_ST7920_128X64_RRD u8g(LCD_PINS_D4, LCD_PINS_ENABLE, LCD_PINS_RS); // Number of stripes can be adjusted in ultralcd_st7920_u8glib_rrd.h with PAGE_HEIGHT
// AVR version ignores these pin settings
// HAL version uses these pin settings
#elif ENABLED(CARTESIO_UI)
// The CartesioUI display
//U8GLIB_DOGM128_2X u8g(DOGLCD_SCK, DOGLCD_MOSI, DOGLCD_CS, DOGLCD_A0); // 4 stripes

View file

@ -1100,7 +1100,7 @@ void Planner::_buffer_steps(const int32_t (&target)[XYZE], float fr_mm_s, const
float max_stepper_speed = 0, min_axis_accel_ratio = 1; // ratio < 1 means acceleration ramp needed
LOOP_XYZE(i) {
const float cs = FABS((current_speed[i] = delta_mm[i] * inverse_secs));
if (cs > max_jerk[i])
if (cs > max_jerk[i])
NOMORE(min_axis_accel_ratio, max_jerk[i] / cs);
NOLESS(max_stepper_speed, cs);
#if ENABLED(DISTINCT_E_FACTORS)

View file

@ -803,7 +803,7 @@ void Temperature::manage_heater() {
meas_shift_index = filwidth_delay_index[0] - meas_delay_cm;
if (meas_shift_index < 0) meas_shift_index += MAX_MEASUREMENT_DELAY + 1; //loop around buffer if needed
meas_shift_index = constrain(meas_shift_index, 0, MAX_MEASUREMENT_DELAY);
calculate_volumetric_for_width_sensor(measurement_delay[meas_shift_index])
planner.calculate_volumetric_for_width_sensor(measurement_delay[meas_shift_index]);
}
#endif // FILAMENT_WIDTH_SENSOR

View file

@ -124,7 +124,7 @@
//
// Temperature Sensors
//
#define TEMP_BED_PIN 15 // K7 - 69 / ADC15 - 15
#define TEMP_BED_PIN 15 // K7 - 69 / ADC15 - 15
// SPI for Max6675 or Max31855 Thermocouple
// Uses a separate SPI bus

View file

@ -122,7 +122,7 @@
#if ENABLED(HAVE_TMC2208)
/*
* TMC2208 stepper drivers
*
*
* Hardware serial communication ports.
* If undefined software serial is used according to the pins below
*/