diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 9bca0c990..2460b8d95 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/default/Configuration.h b/Marlin/src/config/default/Configuration.h
index 9bca0c990..2460b8d95 100644
--- a/Marlin/src/config/default/Configuration.h
+++ b/Marlin/src/config/default/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
index 2dd29d6b9..e7f02efa7 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
@@ -879,6 +879,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
index 41551ede7..4a2c3fde7 100644
--- a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
+++ b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Anet/A2/Configuration.h b/Marlin/src/config/examples/Anet/A2/Configuration.h
index d44784ae9..8145a4606 100644
--- a/Marlin/src/config/examples/Anet/A2/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A2/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Anet/A2plus/Configuration.h b/Marlin/src/config/examples/Anet/A2plus/Configuration.h
index c7d100904..6319cf716 100644
--- a/Marlin/src/config/examples/Anet/A2plus/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A2plus/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration.h b/Marlin/src/config/examples/Anet/A6/Configuration.h
index a8b863d12..216b480f9 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration.h
@@ -935,7 +935,8 @@
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
-#define PROBING_FANS_OFF          // Turn fans off when probing
+#define PROBING_FANS_OFF            // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration.h b/Marlin/src/config/examples/Anet/A8/Configuration.h
index 0832ad694..c94e1f96d 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration.h
@@ -866,6 +866,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
index ecdbe9e3a..255e670bd 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
index 2daa8aa62..cdc16e790 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
index 1ffd99de9..746de9148 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
index 2dac4086d..709ed9877 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
@@ -847,6 +847,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
index 4d53207ad..19cc4c112 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
@@ -860,6 +860,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
index 8aee91646..7b187fea8 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
@@ -847,6 +847,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Cartesio/Configuration.h b/Marlin/src/config/examples/Cartesio/Configuration.h
index f34a0197a..b7bde8851 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration.h
@@ -858,6 +858,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration.h b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
index 84f93e1d2..5840aed57 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
@@ -869,6 +869,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
index 759601236..4b704520f 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
index 031517d8d..e67cbba9f 100644
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
@@ -878,6 +878,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Creality/CR-8/Configuration.h b/Marlin/src/config/examples/Creality/CR-8/Configuration.h
index dad5126ee..087d98dd5 100644
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration.h
@@ -869,6 +869,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
index 7adb1be7e..25e8a2342 100644
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Creality/Ender-3/Configuration.h b/Marlin/src/config/examples/Creality/Ender-3/Configuration.h
index 94e6050fd..a06b1f968 100644
--- a/Marlin/src/config/examples/Creality/Ender-3/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration.h
@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
index 15e972610..5822ae626 100644
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
@@ -869,6 +869,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Einstart-S/Configuration.h b/Marlin/src/config/examples/Einstart-S/Configuration.h
index e9968b91a..be50ddf79 100644
--- a/Marlin/src/config/examples/Einstart-S/Configuration.h
+++ b/Marlin/src/config/examples/Einstart-S/Configuration.h
@@ -869,6 +869,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Felix/Configuration.h b/Marlin/src/config/examples/Felix/Configuration.h
index ef6f2e9b9..68037065e 100644
--- a/Marlin/src/config/examples/Felix/Configuration.h
+++ b/Marlin/src/config/examples/Felix/Configuration.h
@@ -841,6 +841,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Felix/DUAL/Configuration.h b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
index 58dd6f6ac..df611a5cd 100644
--- a/Marlin/src/config/examples/Felix/DUAL/Configuration.h
+++ b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
@@ -841,6 +841,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
index bbd2a032e..2124d7ee4 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
@@ -865,6 +865,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Formbot/Raptor/Configuration.h b/Marlin/src/config/examples/Formbot/Raptor/Configuration.h
index 737561624..335474ea6 100644
--- a/Marlin/src/config/examples/Formbot/Raptor/Configuration.h
+++ b/Marlin/src/config/examples/Formbot/Raptor/Configuration.h
@@ -849,20 +849,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -955,6 +941,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h b/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h
index 96a1bf39e..a4fb62d85 100644
--- a/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h
+++ b/Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h
@@ -897,6 +897,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h
index 88f206bb2..3fea56641 100644
--- a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h
+++ b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h
@@ -880,6 +880,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
index 4b460074b..b79bd21fa 100644
--- a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
@@ -874,6 +874,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
index 89b282d41..4369c3318 100644
--- a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
index 351eed408..8eceac6c1 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
@@ -874,8 +874,9 @@
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
-#define PROBING_FANS_OFF          // Turn fans off when probing
-#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+#define PROBING_FANS_OFF            // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
+#define DELAY_BEFORE_PROBING 200    // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
index 0ec0c8caa..d98429702 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
@@ -874,6 +874,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
index 60a97d5be..beecd0694 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h	
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
index 8d27be747..b31fd97ed 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h	
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
index 1c883a610..d6cabdc3e 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration.h b/Marlin/src/config/examples/JGAurora/A5/Configuration.h
index abd992050..bdbe64a90 100644
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration.h
@@ -871,6 +871,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/MakerParts/Configuration.h b/Marlin/src/config/examples/MakerParts/Configuration.h
index 3666579d9..285b14d13 100644
--- a/Marlin/src/config/examples/MakerParts/Configuration.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration.h
@@ -879,6 +879,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration.h b/Marlin/src/config/examples/Malyan/M150/Configuration.h
index c235e03fe..73b0ab338 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration.h
@@ -883,6 +883,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration.h b/Marlin/src/config/examples/Malyan/M200/Configuration.h
index 784d6c142..bde76b887 100644
--- a/Marlin/src/config/examples/Malyan/M200/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration.h
@@ -858,6 +858,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
index b30a60ea6..8ada3210f 100644
--- a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
index cc9676a5f..ecbcd89f9 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration.h b/Marlin/src/config/examples/Mks/Sbase/Configuration.h
index 48c4fb06f..09a0f6d56 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
index 0fa8ddd59..19fc653ee 100644
--- a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
@@ -899,6 +899,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
index c58499cf1..8ccb645c2 100644
--- a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/RigidBot/Configuration.h b/Marlin/src/config/examples/RigidBot/Configuration.h
index 25b9b6718..3fe687440 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration.h
@@ -857,6 +857,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/SCARA/Configuration.h b/Marlin/src/config/examples/SCARA/Configuration.h
index 98595994d..fa52c105a 100644
--- a/Marlin/src/config/examples/SCARA/Configuration.h
+++ b/Marlin/src/config/examples/SCARA/Configuration.h
@@ -872,6 +872,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/STM32F10/Configuration.h b/Marlin/src/config/examples/STM32F10/Configuration.h
index 14603c2f6..875b9c7c9 100644
--- a/Marlin/src/config/examples/STM32F10/Configuration.h
+++ b/Marlin/src/config/examples/STM32F10/Configuration.h
@@ -861,6 +861,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/STM32F4/Configuration.h b/Marlin/src/config/examples/STM32F4/Configuration.h
index 0cd7489ef..785f76d48 100644
--- a/Marlin/src/config/examples/STM32F4/Configuration.h
+++ b/Marlin/src/config/examples/STM32F4/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration.h b/Marlin/src/config/examples/Sanguinololu/Configuration.h
index b6f739f56..bae8e869b 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration.h
@@ -890,6 +890,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/TheBorg/Configuration.h b/Marlin/src/config/examples/TheBorg/Configuration.h
index 19cec07fd..5f431a80a 100644
--- a/Marlin/src/config/examples/TheBorg/Configuration.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration.h b/Marlin/src/config/examples/TinyBoy2/Configuration.h
index 943fcb1cb..269c4d150 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration.h
@@ -910,6 +910,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Tronxy/X1/Configuration.h b/Marlin/src/config/examples/Tronxy/X1/Configuration.h
index f56ffe7f7..819eac8f3 100644
--- a/Marlin/src/config/examples/Tronxy/X1/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X1/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Tronxy/X3A/Configuration.h b/Marlin/src/config/examples/Tronxy/X3A/Configuration.h
index f08350166..1066117d2 100644
--- a/Marlin/src/config/examples/Tronxy/X3A/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X3A/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Tronxy/X5S/Configuration.h b/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
index ab63e4831..4052a0524 100644
--- a/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Tronxy/XY100/Configuration.h b/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
index 08f9da9b4..4f9e4dc6b 100644
--- a/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
@@ -870,6 +870,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
index 1f4ebbaab..6c1143653 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration.h b/Marlin/src/config/examples/Velleman/K8200/Configuration.h
index 64890c495..799abb667 100644
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration.h
@@ -888,6 +888,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Configuration.h
index beee331cd..c9cdd86a7 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
index c0251014d..29ea4cfb0 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h
index 71848e48d..fb0414e5a 100644
--- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h	
+++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h	
@@ -869,6 +869,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
index 2e08dd910..613bf1c0f 100644
--- a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
+++ b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h
index 6510d53b4..ebe9d5aea 100644
--- a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h
+++ b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h
@@ -1048,6 +1048,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index 472334bdf..9703bc38e 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -987,6 +987,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
index 11d8385b9..c01d43053 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
@@ -986,6 +986,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index b398abc5a..0b2ec4afa 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -986,6 +986,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
index 343f605ff..31620202b 100644
--- a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
+++ b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
@@ -988,7 +988,8 @@
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
-#define PROBING_FANS_OFF          // Turn fans off when probing
+#define PROBING_FANS_OFF            // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/delta/generic/Configuration.h b/Marlin/src/config/examples/delta/generic/Configuration.h
index 31458df74..6ed9a891d 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration.h
@@ -974,6 +974,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
index 632e6f007..843ca45b2 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
@@ -976,6 +976,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
index a68fe8d8f..125f95995 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
@@ -977,6 +977,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
index c57f7ba3e..7270b6980 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
@@ -977,6 +977,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
index 986c1698c..16a86d05f 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
@@ -872,6 +872,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/makibox/Configuration.h b/Marlin/src/config/examples/makibox/Configuration.h
index 1edc89c0d..f7e1ad2ac 100644
--- a/Marlin/src/config/examples/makibox/Configuration.h
+++ b/Marlin/src/config/examples/makibox/Configuration.h
@@ -862,6 +862,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/stm32f103ret6/Configuration.h b/Marlin/src/config/examples/stm32f103ret6/Configuration.h
index ff00d32a3..cc435600d 100644
--- a/Marlin/src/config/examples/stm32f103ret6/Configuration.h
+++ b/Marlin/src/config/examples/stm32f103ret6/Configuration.h
@@ -861,6 +861,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
index 10f1421c5..e198f00c0 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
@@ -854,6 +854,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/config/examples/wt150/Configuration.h b/Marlin/src/config/examples/wt150/Configuration.h
index 51b588ddb..ae9dfc063 100644
--- a/Marlin/src/config/examples/wt150/Configuration.h
+++ b/Marlin/src/config/examples/wt150/Configuration.h
@@ -864,6 +864,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
diff --git a/Marlin/src/module/probe.cpp b/Marlin/src/module/probe.cpp
index 20f3c665d..797ec5fb0 100644
--- a/Marlin/src/module/probe.cpp
+++ b/Marlin/src/module/probe.cpp
@@ -292,6 +292,12 @@ float zprobe_zoffset; // Initialized by settings.load()
     #if ENABLED(PROBING_FANS_OFF)
       fans_pause(p);
     #endif
+    #if ENABLED(PROBING_STEPPERS_OFF)
+      disable_e_steppers();
+      #if DISABLED(DELTA)
+        disable_X(); disable_Y();
+      #endif
+    #endif
     if (p) safe_delay(
       #if DELAY_BEFORE_PROBING > 25
         DELAY_BEFORE_PROBING