Update default/Configuration_adv.h

This commit is contained in:
Scott Lahteine 2019-06-28 23:10:02 -05:00
parent 49027721e9
commit f39d025a80

View file

@ -1732,7 +1732,6 @@
//#define E5_CS_PIN -1 //#define E5_CS_PIN -1
/** /**
* Use software SPI for TMC2130.
* Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160).
* The default SW SPI pins are defined the respective pins files, * The default SW SPI pins are defined the respective pins files,
* but you can override or define them here. * but you can override or define them here.
@ -1774,7 +1773,7 @@
//#define SOFTWARE_DRIVER_ENABLE //#define SOFTWARE_DRIVER_ENABLE
/** /**
* TMC2130, TMC2160, TMC2208, TMC5130 and TMC5160 only * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
* Use Trinamic's ultra quiet stepping mode. * Use Trinamic's ultra quiet stepping mode.
* When disabled, Marlin will use spreadCycle stepping mode. * When disabled, Marlin will use spreadCycle stepping mode.
*/ */
@ -1800,7 +1799,7 @@
/** /**
* Monitor Trinamic drivers for error conditions, * Monitor Trinamic drivers for error conditions,
* like overtemperature and short to ground. TMC2208 requires hardware serial. * like overtemperature and short to ground.
* In the case of overtemperature Marlin can decrease the driver current until error condition clears. * In the case of overtemperature Marlin can decrease the driver current until error condition clears.
* Other detected conditions can be used to stop the current print. * Other detected conditions can be used to stop the current print.
* Relevant g-codes: * Relevant g-codes:
@ -1818,7 +1817,7 @@
#endif #endif
/** /**
* TMC2130, TMC2160, TMC2208, TMC5130 and TMC5160 only * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only
* The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
* This mode allows for faster movements at the expense of higher noise levels. * This mode allows for faster movements at the expense of higher noise levels.
* STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
@ -1841,7 +1840,7 @@
#define E5_HYBRID_THRESHOLD 30 #define E5_HYBRID_THRESHOLD 30
/** /**
* TMC2130, TMC2160, TMC2660, TMC5130, and TMC5160 only * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only
* Use StallGuard2 to sense an obstacle and trigger an endstop. * Use StallGuard2 to sense an obstacle and trigger an endstop.
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode. * X, Y, and Z homing will always be done in spreadCycle mode.
@ -1853,7 +1852,7 @@
* It is advised to set X/Y/Z_HOME_BUMP_MM to 0. * It is advised to set X/Y/Z_HOME_BUMP_MM to 0.
* M914 X/Y/Z to live tune the setting * M914 X/Y/Z to live tune the setting
*/ */
//#define SENSORLESS_HOMING // TMC2130 only //#define SENSORLESS_HOMING // StallGuard capable drivers only
/** /**
* Use StallGuard2 to probe the bed with the nozzle. * Use StallGuard2 to probe the bed with the nozzle.
@ -1861,9 +1860,10 @@
* CAUTION: This could cause damage to machines that use a lead screw or threaded rod * CAUTION: This could cause damage to machines that use a lead screw or threaded rod
* to move the Z axis. Take extreme care when attempting to enable this feature. * to move the Z axis. Take extreme care when attempting to enable this feature.
*/ */
//#define SENSORLESS_PROBING // TMC2130 only //#define SENSORLESS_PROBING // StallGuard capable drivers only
#if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
// TMC2209: 0...255. TMC2130: -64...63
#define X_STALL_SENSITIVITY 8 #define X_STALL_SENSITIVITY 8
#define Y_STALL_SENSITIVITY 8 #define Y_STALL_SENSITIVITY 8
//#define Z_STALL_SENSITIVITY 8 //#define Z_STALL_SENSITIVITY 8