diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h
index 798416d8e..3fe919c82 100644
--- a/config/examples/Geeetech/A20M/Configuration.h
+++ b/config/examples/Geeetech/A20M/Configuration.h
@@ -766,7 +766,7 @@
  *
  * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  */
-//#define S_CURVE_ACCELERATION
+#define S_CURVE_ACCELERATION
 
 //===========================================================================
 //============================= Z Probe Options =============================
@@ -1734,7 +1734,7 @@
 //
 // ULTIPANEL as seen on Thingiverse.
 //
-#define ULTIPANEL
+//#define ULTIPANEL
 
 //
 // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h
index 8572da54b..469fa3769 100644
--- a/config/examples/Geeetech/A20M/Configuration_adv.h
+++ b/config/examples/Geeetech/A20M/Configuration_adv.h
@@ -934,7 +934,7 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define POWER_LOSS_PIN           69 // Pin to detect power loss
     #define POWER_LOSS_STATE        LOW // State of pin indicating power loss
-    //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
+    #define POWER_LOSS_PULL             // Set pullup / pulldown as appropriate
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
 
@@ -985,7 +985,7 @@
   //#define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
-  //#define SCROLL_LONG_FILENAMES
+  #define SCROLL_LONG_FILENAMES
 
   // Leave the heaters on after Stop Print (not recommended!)
   //#define SD_ABORT_NO_COOLDOWN
@@ -1153,12 +1153,12 @@
   #define STATUS_FAN_FRAMES 3         // :[0,1,2,3,4] Number of fan animation frames
   #define STATUS_HEAT_PERCENT         // Show heating in a progress bar
   #define BOOT_MARLIN_LOGO_SMALL      // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
-  //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
+  #define BOOT_MARLIN_LOGO_ANIMATED   // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
 
   // Frivolous Game Options
-  //#define MARLIN_BRICKOUT
-  //#define MARLIN_INVADERS
-  //#define MARLIN_SNAKE
+  #define MARLIN_BRICKOUT
+  #define MARLIN_INVADERS
+  #define MARLIN_SNAKE
   //#define GAMES_EASTER_EGG          // Add extra blank lines above the "Games" sub-menu
 
 #endif // HAS_GRAPHICAL_LCD
@@ -1277,7 +1277,7 @@
     #endif
   #endif
 
-  //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
+  #define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
@@ -1304,10 +1304,10 @@
  * See http://marlinfw.org/docs/features/lin_advance.html for full instructions.
  * Mention @Sebastianv650 on GitHub to alert the author of any issues.
  */
-//#define LIN_ADVANCE
+#define LIN_ADVANCE
 #if ENABLED(LIN_ADVANCE)
   //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
-  #define LIN_ADVANCE_K 0.22    // Unit: mm compression per 1mm/s extruder speed
+  #define LIN_ADVANCE_K 0       // Unit: mm compression per 1mm/s extruder speed
   //#define LA_DEBUG            // If enabled, this will generate debug information output over USB.
 #endif
 
@@ -2380,7 +2380,7 @@
  *  - M206 and M428 are disabled.
  *  - G92 will revert to its behavior from Marlin 1.0.
  */
-#define NO_WORKSPACE_OFFSETS
+//#define NO_WORKSPACE_OFFSETS
 
 /**
  * Set the number of proportional font spaces required to fill up a typical character space.