From f5092e92a44697da1a04bb6b6e251180f0a3ee5a Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Sun, 22 Sep 2019 18:18:51 -0500 Subject: [PATCH] Enhanced A20M config --- config/examples/Geeetech/A20M/Configuration.h | 4 ++-- .../Geeetech/A20M/Configuration_adv.h | 20 +++++++++---------- 2 files changed, 12 insertions(+), 12 deletions(-) diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index 798416d8e..3fe919c82 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -766,7 +766,7 @@ * * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained */ -//#define S_CURVE_ACCELERATION +#define S_CURVE_ACCELERATION //=========================================================================== //============================= Z Probe Options ============================= @@ -1734,7 +1734,7 @@ // // ULTIPANEL as seen on Thingiverse. // -#define ULTIPANEL +//#define ULTIPANEL // // PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index 8572da54b..469fa3769 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -934,7 +934,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define POWER_LOSS_PIN 69 // Pin to detect power loss #define POWER_LOSS_STATE LOW // State of pin indicating power loss - //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate + #define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. @@ -985,7 +985,7 @@ //#define LONG_FILENAME_HOST_SUPPORT // Enable this option to scroll long filenames in the SD card menu - //#define SCROLL_LONG_FILENAMES + #define SCROLL_LONG_FILENAMES // Leave the heaters on after Stop Print (not recommended!) //#define SD_ABORT_NO_COOLDOWN @@ -1153,12 +1153,12 @@ #define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames #define STATUS_HEAT_PERCENT // Show heating in a progress bar #define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) - //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM. + #define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM. // Frivolous Game Options - //#define MARLIN_BRICKOUT - //#define MARLIN_INVADERS - //#define MARLIN_SNAKE + #define MARLIN_BRICKOUT + #define MARLIN_INVADERS + #define MARLIN_SNAKE //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1277,7 +1277,7 @@ #endif #endif - //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + #define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping #if ENABLED(BABYSTEP_ZPROBE_OFFSET) @@ -1304,10 +1304,10 @@ * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. * Mention @Sebastianv650 on GitHub to alert the author of any issues. */ -//#define LIN_ADVANCE +#define LIN_ADVANCE #if ENABLED(LIN_ADVANCE) //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants - #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + #define LIN_ADVANCE_K 0 // Unit: mm compression per 1mm/s extruder speed //#define LA_DEBUG // If enabled, this will generate debug information output over USB. #endif @@ -2380,7 +2380,7 @@ * - M206 and M428 are disabled. * - G92 will revert to its behavior from Marlin 1.0. */ -#define NO_WORKSPACE_OFFSETS +//#define NO_WORKSPACE_OFFSETS /** * Set the number of proportional font spaces required to fill up a typical character space.