Follow-up the PR #3082, etc

Follow-up the PR #3082
Follow-up the commit 143ad74: unnoticed updates
Fix for commit b0f5ba0: Z offset: -front [of the nozzle] +behind -> Y offset: -front [of the nozzle] +behind
Standardize the writing method: Z-probe, z-probe -> Z Probe
Adjust spacing
This commit is contained in:
esenapaj 2016-03-22 20:22:01 +09:00
parent cadded1e21
commit fc75e6f92d
19 changed files with 271 additions and 321 deletions

View file

@ -341,7 +341,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -488,7 +488,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. #define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -551,7 +551,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.

View file

@ -323,7 +323,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -355,16 +355,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -470,7 +470,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. //#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -533,7 +533,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -555,14 +555,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -320,7 +320,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -352,16 +352,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -467,7 +467,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. //#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -530,7 +530,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -552,14 +552,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -333,7 +333,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -365,16 +365,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -480,7 +480,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. #define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -543,7 +543,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -565,14 +565,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -335,8 +335,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// The Z_MIN_PIN will then be used for both Z-homing and probing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
// //
@ -367,13 +367,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// To use a probe you must enable one of the two options above! // To use a probe you must enable one of the two options above!
//
// This option disables the use of the Z_MIN_PROBE_PIN // This option disables the use of the Z_MIN_PROBE_PIN
// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
@ -483,7 +482,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) #define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. #define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -584,7 +583,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// - Position the Z probe in a defined XY point before Z Homing when homing all axis (G28). // - Position the Z probe in a defined XY point before Z Homing when homing all axis (G28).
// - Block Z homing only when the Z probe is outside bed area. // - Block Z homing only when the Z probe is outside bed area.
#if ENABLED(Z_SAFE_HOMING) #if ENABLED(Z_SAFE_HOMING)
#define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28). #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).

View file

@ -356,7 +356,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -388,16 +388,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -503,7 +503,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. #define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -566,7 +566,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -588,14 +588,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.
@ -726,7 +725,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define ULTRA_LCD //general LCD support, also 16x2 //#define ULTRA_LCD //general LCD support, also 16x2
//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) //#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
#define SDSUPPORT // Enable SD Card Support in Hardware Console #define SDSUPPORT // Enable SD Card Support in Hardware Console
// Changed behaviour! If you need SDSUPPORT uncomment it! // Changed behaviour! If you need SDSUPPORT uncomment it!
//#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) //#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)

View file

@ -341,7 +341,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -373,16 +373,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -488,7 +488,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. #define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -551,7 +551,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -573,14 +573,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -335,7 +335,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -367,16 +367,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -482,7 +482,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. //#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -545,7 +545,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -567,14 +567,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -349,7 +349,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -381,16 +381,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -496,7 +496,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. //#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -559,7 +559,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -581,14 +581,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
//#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. //#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -204,7 +204,7 @@ Here are some standard links for getting your machine calibrated:
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
#define K1 0.95 //smoothing factor within the PID #define K1 0.95 //smoothing factor within the PID
// If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
// Buda 2.0 on 24V // Buda 2.0 on 24V
#define DEFAULT_Kp 6 #define DEFAULT_Kp 6
#define DEFAULT_Ki .3 #define DEFAULT_Ki .3
@ -257,6 +257,7 @@ Here are some standard links for getting your machine calibrated:
//#define PID_BED_DEBUG // Sends debug data to the serial port. //#define PID_BED_DEBUG // Sends debug data to the serial port.
#if ENABLED(PIDTEMPBED) #if ENABLED(PIDTEMPBED)
#define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term #define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
//24V 360W silicone heater from NPH on 3mm borosilicate (TAZ 2.2+) //24V 360W silicone heater from NPH on 3mm borosilicate (TAZ 2.2+)
@ -361,7 +362,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -393,16 +394,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -508,7 +509,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. #define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -571,7 +572,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -593,14 +594,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.
@ -617,37 +617,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
#endif #endif
// Support for a dedicated Z probe endstop separate from the Z min endstop.
// If you would like to use both a Z probe and a Z min endstop together,
// uncomment #define Z_MIN_PROBE_ENDSTOP and read the instructions below.
// If you still want to use the Z min endstop for homing, disable Z_SAFE_HOMING above.
// Example: To park the head outside the bed area when homing with G28.
//
// WARNING:
// The Z min endstop will need to set properly as it would without a Z probe
// to prevent head crashes and premature stopping during a print.
//
// To use a separate Z probe endstop, you must have a Z_MIN_PROBE_PIN
// defined in the pins_XXXXX.h file for your control board.
// If you are using a servo based Z probe, you will need to enable NUM_SERVOS,
// Z_ENDSTOP_SERVO_NR and SERVO_ENDSTOP_ANGLES in the R/C SERVO support below.
// RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin
// in the Aux 4 section of the RAMPS board. Use 5V for powered sensors,
// otherwise connect to ground and D32 for normally closed configuration
// and 5V and D32 for normally open configurations.
// Normally closed configuration is advised and assumed.
// The D32 pin in Aux 4 on RAMPS maps to the Arduino D32 pin.
// Z_MIN_PROBE_PIN is setting the pin to use on the Arduino.
// Since the D32 pin on the RAMPS maps to D32 on Arduino, this works.
// D32 is currently selected in the RAMPS 1.3/1.4 pin file.
// All other boards will need changes to the respective pins_XXXXX.h file.
//
// WARNING:
// Setting the wrong pin may have unexpected and potentially disastrous outcomes.
// Use with caution and do your homework.
//
//#define Z_MIN_PROBE_ENDSTOP
#endif // AUTO_BED_LEVELING_FEATURE #endif // AUTO_BED_LEVELING_FEATURE

View file

@ -333,7 +333,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -365,16 +365,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -480,7 +480,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. #define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -543,7 +543,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -565,14 +565,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -341,7 +341,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -373,16 +373,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -488,7 +488,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. #define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -551,7 +551,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -573,14 +573,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -376,7 +376,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -408,16 +408,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -523,7 +523,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. //#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -590,7 +590,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 4000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 4000 // X and Y axis travel speed between probes, in mm/min.
@ -612,12 +612,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// Allen key retractable Z probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe // Allen key retractable Z probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
//#define Z_PROBE_ALLEN_KEY //#define Z_PROBE_ALLEN_KEY
@ -699,8 +698,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ
#endif #endif
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//it is highly recommended you let this Z_SAFE_HOMING enabled!!! // it is highly recommended you leave Z_SAFE_HOMING enabled!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -376,7 +376,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -408,16 +408,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// //
#define Z_MIN_PROBE_ENDSTOP #define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN //#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -523,7 +523,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. //#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -589,9 +589,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// | | // | |
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // Z probe to nozzle X offset: -left +right #define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Z probe to nozzle Y offset: -front +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z probe to nozzle Z offset: -below (always!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 4000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 4000 // X and Y axis travel speed between probes, in mm/min.
@ -612,13 +612,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// Allen key retractable Z probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
//#define Z_PROBE_ALLEN_KEY //#define Z_PROBE_ALLEN_KEY
@ -699,8 +698,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ //#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ
#endif #endif
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//it is highly recommended you let this Z_SAFE_HOMING enabled!!! // it is highly recommended you leave Z_SAFE_HOMING enabled!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -376,7 +376,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -408,16 +408,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -523,7 +523,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. //#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -590,7 +590,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 4000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 4000 // X and Y axis travel speed between probes, in mm/min.
@ -612,13 +612,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// Allen key retractable Z probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
#define Z_PROBE_ALLEN_KEY #define Z_PROBE_ALLEN_KEY
@ -703,8 +702,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ //#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ
#endif #endif
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//it is highly recommended you let this Z_SAFE_HOMING enabled!!! // it is highly recommended you leave Z_SAFE_HOMING enabled!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -363,7 +363,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -395,16 +395,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -510,7 +510,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) #define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. //#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -601,13 +601,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// Allen key retractable Z probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. // Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
#define Z_PROBE_ALLEN_KEY #define Z_PROBE_ALLEN_KEY
@ -688,8 +687,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_XYZ
#endif #endif
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//it is highly recommended you let this Z_SAFE_HOMING enabled!!! // it is highly recommended you leave Z_SAFE_HOMING enabled!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -369,7 +369,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -401,16 +401,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -516,7 +516,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) #define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
//#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. //#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -582,7 +582,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER 0.0 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER 0.0 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER 0.0 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER 0.3 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 7000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 7000 // X and Y axis travel speed between probes, in mm/min.
@ -605,14 +605,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -344,7 +344,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -376,16 +376,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -491,7 +491,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. #define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -554,7 +554,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -576,14 +576,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.

View file

@ -331,7 +331,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//============================= Z Probe Options ============================= //============================= Z Probe Options =============================
//=========================================================================== //===========================================================================
// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z-probe and a Z-min-endstop on the same machine. // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
// //
// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! *** // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
@ -363,16 +363,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// //
//#define Z_MIN_PROBE_ENDSTOP //#define Z_MIN_PROBE_ENDSTOP
// If you want to use the Z_MIN_PIN to connect your Z_MIN_PROBE comment out the next define. // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
// In other words. The z-min-probe is connected to the Z_MIN_PIN and is used for homing and for probing. // The Z_MIN_PIN will then be used for both Z-homing and probing.
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// If you want to use a probe you do have to define one of the two defines above!
// If you want to enable the Z probe pin, but disable its use, uncomment the line below. // To use a probe you must enable one of the two options above!
// This only affects a Z probe endstop if you have separate Z min endstop as well and have
// activated Z_MIN_PROBE_ENDSTOP above. If you are using the Z Min endstop on your Z probe, // This option disables the use of the Z_MIN_PROBE_PIN
// this has no effect. // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
// In other words. If a Z_MIN_PROBE_PIN is defined in your pin file - don't use it. // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
//#define DISABLE_Z_MIN_PROBE_ENDSTOP //#define DISABLE_Z_MIN_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -478,7 +478,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line) //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE //#define DEBUG_LEVELING_FEATURE
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. #define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(AUTO_BED_LEVELING_FEATURE) #if ENABLED(AUTO_BED_LEVELING_FEATURE)
@ -541,7 +541,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// O-- FRONT --+ // O-- FRONT --+
// (0,0) // (0,0)
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left [of the nozzle] +right
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Z offset: -front [of the nozzle] +behind #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front [of the nozzle] +behind
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!) #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below [the nozzle] (always negative!)
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min.
@ -563,14 +563,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// A Servo Probe can be defined in the servo section below. // A Servo Probe can be defined in the servo section below.
// A Allen Key Probe is currently predefined only in the delta example configurations. // An Allen Key Probe is currently predefined only in the delta example configurations.
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, // it is highly recommended you leave Z_SAFE_HOMING enabled!
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop. #define Z_SAFE_HOMING // Use the z-min-probe for homing to z-min - not the z-min-endstop.
// This feature is meant to avoid Z homing with Z probe outside the bed area. // This feature is meant to avoid Z homing with Z probe outside the bed area.