Commit graph

6840 commits

Author SHA1 Message Date
MagoKimbra 663ff7f92a Fix G29 with 3 point 2017-06-04 14:39:31 +02:00
oldmcg 9f295581f0 Ubl delta fixes and improvements (#6941)
* Change all direct changes of ubl.state.active to
  set_bed_leveling_enabled() which handles apply/unapply
  leveling to maintain current_position consistency.

Fix invalidation of UBL mesh to invalid unreachable
  mesh points as well (delta corners).

Fix UBL_DELTA unapply_leveling logic and when
it gets applied, including fade_height changes.

Add optional M114 D for detailed position information,
disabled from compilation by default (M114_DETAIL).

* UBL_DELTA raw and inline kinematics

* UBL planner fall through fix

* consistent variable names

* Cleanup orphaned code and whitespace changes.
Use _O2.

* compile warnings cleanup

* Remove redundant #ifdef condition
2017-06-03 17:11:43 -05:00
Bob-the-Kuhn c34d7a29a6 fix redefinition errors for redundant_temperature
Removing redundant_temperature from public section and leaving it in the
private section
2017-06-03 16:40:14 -05:00
Bob-the-Kuhn 6a5d3b580d fix "hex_address not defined" when UBL is enabled 2017-06-03 13:19:55 -05:00
Scott Lahteine 789b2928a8 Tweak scrolling message code 2017-06-02 23:45:53 -05:00
Scott Lahteine fc7d7f87b4 Init probe test pin with FastIO 2017-06-02 23:45:52 -05:00
Scott Lahteine 0282452cea Make Parser::seen volatile 2017-06-02 23:45:52 -05:00
Scott Lahteine 9a305a467b Patch LCD Contrast menu item 2017-06-02 23:45:52 -05:00
Scott Lahteine 90ccac4bcf Clean up after recent commits 2017-06-02 23:45:52 -05:00
Bob-the-Kuhn 2130f10de8 allow space between parameter and value 2017-06-02 19:57:22 -05:00
Bob-the-Kuhn ebda4663c3 for discusion 2017-06-02 19:42:43 -05:00
FATALHERMIT 911079104e Support for ZRIB v2.0 Control Board 2017-06-02 12:05:46 -05:00
Scott Lahteine 65a0212866 Easier override of FILWIDTH_PIN 2017-06-02 12:05:46 -05:00
Scott Lahteine 147d9d76fc Merge pull request #6928 from Bob-the-Kuhn/Fix-case-light-logic-on-Azteeg-X3-boards
Fix case light logic on Azteeg_X3 boards.
2017-06-01 20:14:15 -05:00
guntherv73 4288c4fb4f Configurations for Malyan M150 2017-06-01 19:26:29 -05:00
Scott Lahteine 1919cb0d1e Config cleanups 2017-06-01 19:26:16 -05:00
Bob-the-Kuhn 9a9bbfc57c Fix case light logic on Azteeg_X3 boards. 2017-06-01 12:33:24 -05:00
Thomas Moore a32f7b329c Fix heater status display for advanced pause 2017-06-01 12:29:47 -05:00
Scott Lahteine 445865ea03 REPRAPWORLD_KEYPAD is NEWPANEL but not ULTIPANEL 2017-05-31 23:48:03 -05:00
Scott Lahteine 4296a8b74e For status scrolling, pad a short message 2017-05-31 23:48:03 -05:00
Scott Lahteine 4a96433b7e Simplify counting of printable characters 2017-05-31 23:45:41 -05:00
Scott Lahteine 8d69394ae1 Fix LCD printing of progmem strings 2017-05-31 23:36:57 -05:00
Scott Lahteine c74d4dede6 Prevent illegal leveling combinations
Addressing issue #6901
2017-05-31 23:36:57 -05:00
Scott Lahteine 155aa62fb0 Merge pull request #6912 from thinkyhead/bf_better_pulse_delay
Account for dual XYZ in pulse delay cycles estimate
2017-05-31 22:21:47 -05:00
Scott Lahteine a5fa586642 Preferred patch to gcode.h 2017-05-31 21:18:16 -05:00
Bob-the-Kuhn 1b41e1f645 another compile error
only seen if

#if ENABLED(TEMPERATURE_UNITS_SUPPORT)
      ...
    #if
ENABLED(ULTIPANEL) && DISABLED(DISABLE_M503)
2017-05-31 13:59:49 -05:00
Bob-the-Kuhn 65bd4c8c94 Merge pull request #6797 from Bob-the-Kuhn/M355-case-lightimprovements-(1.1.x)
M355 case light improvements (replaces PR #5685)
2017-05-31 13:33:59 -05:00
Bob-the-Kuhn 9657e7d3ee copied file changes from PR #5685
==============================

Configuration_adv.h changes

==============================

add "live" LCD update

==============================

P & S version

==============================

final (hopefully) tested version

==============================

update M115 capabilities print

==============================

Menu changes portion of the requested changes

==============================

changed USEABLE_HARDWARE_PWM from a function to a series of macros

==============================

changes per review
2017-05-31 13:22:38 -05:00
Bob-the-Kuhn 8206bb9bb9 fix compile error
invalid conversion from 'const char*' to 'char*' [-fpermissive]
2017-05-31 13:17:01 -05:00
Scott Lahteine df91346188 Account for dual XYZ in pulse delay cycles estimate 2017-05-31 12:23:28 -05:00
Scott Lahteine 7236109f2a Patch M24 / M125 for delta 2017-05-30 23:07:29 -05:00
Scott Lahteine be17033762 Fix case light menu toggle 2017-05-30 14:03:45 -05:00
Scott Lahteine 89b93058e3 Merge pull request #6887 from christianh17/PR-sanitycheck
enable DEACTIVATE_SERVOS_AFTER_MOVE with switching nozzle
2017-05-30 13:43:39 -05:00
Scott Lahteine 05b66234ae Merge pull request #6895 from thinkyhead/bf_user_commands
Custom user commands menu
2017-05-30 13:40:50 -05:00
Scott Lahteine 84a0a77c59 Merge pull request #6852 from tcm0116/mixing_extruder_lin_advance
Generate error if MIXING_EXTRUDER and LIN_ADVANCE are both enabled
2017-05-30 13:37:51 -05:00
Scott Lahteine 266ae8912a Formatting in _draw_heater_status 2017-05-30 03:32:16 -05:00
Scott Lahteine 6b9ca16f36 Patch lcd_print edge limit code 2017-05-30 03:32:15 -05:00
Tannoo 74d6dee920 User Command (Script) Menu
The menu (commands / scripts) is configurable in `Configuration_adv.h`.

- Added conditionals.
- Changed script handling.
- Slimmed and working!
- Added Status message.
- Returning to lcd status screen now!
- Example Configs Updated.
- Cleanups by @thinkyhead
2017-05-30 02:33:57 -05:00
Scott Lahteine d9c8072037 Edit PROPORTIONAL_FONT_RATIO comment 2017-05-30 01:29:39 -05:00
Scott Lahteine 46b32e4548 Cleanup LCD interface, add lcd_reset_status 2017-05-29 22:16:13 -05:00
Scott Lahteine ca99d67ede Fix UBL "Info screen" menu items 2017-05-29 19:55:26 -05:00
Scott Lahteine 2c7a39bc0e Fix LCD print aborted message 2017-05-29 19:52:01 -05:00
Scott Lahteine 0f1e8c195d Draw on LCD after value has changed 2017-05-29 19:42:30 -05:00
Scott Lahteine 51587c4b43 Rename Feedrate to Velocity to match prior naming 2017-05-29 17:54:15 -05:00
Scott Lahteine 9677f3f2f5 Patch up LCD Bed Leveling menu 2017-05-29 17:51:11 -05:00
Scott Lahteine fc2eaab7f3 Show home option in level bed menu 2017-05-29 17:51:10 -05:00
Scott Lahteine c6a7adc293 Patch G29 A and Q arguments to bypass setup 2017-05-29 17:51:10 -05:00
Scott Lahteine 4cece2d72e Use NAN for G29 W omitted parameters 2017-05-29 17:51:10 -05:00
Scott Lahteine 2d71569138 Fix spacing in JSON output 2017-05-29 17:51:10 -05:00
Scott Lahteine b2d3c8aedd Have G28 do a refresh of the display 2017-05-29 17:51:10 -05:00
Scott Lahteine 50ab9c2e04 General cleanup of spacing, comments 2017-05-29 15:34:14 -05:00
Scott Lahteine f1e33afda4 Return to Bed Leveling menu when done 2017-05-29 15:31:02 -05:00
Scott Lahteine 78d8c598e1 Fix lcd_synchronize with message 2017-05-29 15:31:02 -05:00
Scott Lahteine eb39d6e3e2 Don't draw progress bar until it has 1% 2017-05-29 15:31:01 -05:00
Scott Lahteine 194f8b2f55 Start at Z=0 in manual probing 2017-05-29 15:31:01 -05:00
Scott Lahteine 6f89db11f0 Allow lcd_setstatusPGM to reset the alert level 2017-05-29 15:31:00 -05:00
Scott Lahteine 3fe333143c Case light as a toggle menu item 2017-05-28 14:32:07 -05:00
Scott Lahteine d013bddfa8 Merge pull request #6876 from thinkyhead/bf_extend_leveling_menu
Extend the ABL/MBL Bed Leveling menu
2017-05-28 14:19:02 -05:00
Scott Lahteine 01e7e234c6 Add more options to the Bed Leveling menu 2017-05-28 14:04:28 -05:00
Scott Lahteine 0cbe448edf Split up Control > Motion submenu 2017-05-28 12:52:24 -05:00
Scott Lahteine a3645ec921 Reference op with variable name 2017-05-28 11:33:22 -05:00
Scott Lahteine 71367fd518 Scrolling status message option 2017-05-28 11:26:28 -05:00
Scott Lahteine b0eae68f57 Prevent bed temperature being set too high 2017-05-28 11:11:17 -05:00
Scott Lahteine 493f0b0c62 Fix some compiler warnings 2017-05-28 11:06:33 -05:00
christianh17 f379a326cc enable DEACTIVATE_SERVOS_AFTER_MOVE with switching nozzle
When using switching nozzle it should be possible to disable the servo after move. Do it only if you do not need the servo power to keep the position.
2017-05-28 15:33:28 +02:00
Scott Lahteine 33279a1e02 Code style tweak to gcode.h 2017-05-27 19:47:26 -05:00
Ernesto Martinez ac959b12ee Updates to language_es.h based on latest updates. (#6871)
Spanish language updates
2017-05-27 19:08:39 -05:00
Scott Lahteine 55c700d537 Tweak to gcode.h 2017-05-26 22:11:31 -05:00
Bob-the-Kuhn 868e7db4ae value check was looking at the code 2017-05-26 14:49:42 -05:00
Thomas Moore fb5e0ffe16 Unify M600 and M125 pause features (#6407)
* Unify M600 and M125 pause features
* Cleanup per thinkyhead's comments
* Rename filament_change_menu_response to advanced_pause_menu_response
* Include HAS_BED_PROBE in QUIET_PROBING
* Update gMax example file
* is_idle() is out of scope without the braces
* Convert FT-i3-2020 to Advance Pause names...
* Allow pause even if not printing
2017-05-26 13:01:02 -05:00
Scott Lahteine b3a97b5013 Patch up LCD level bed menus 2017-05-25 23:53:31 -05:00
Scott Lahteine 78af2b1444 Fix PROBE_MANUALLY via G-code 2017-05-25 23:53:31 -05:00
Scott Lahteine 082da23391 One fewer EOL in M503 output 2017-05-25 23:53:31 -05:00
Scott Lahteine b15e531464 Fix screen change on character display 2017-05-25 15:29:14 -05:00
Thomas Moore 44e657766e Add incompatibility error to Sanity Check for MIXING_EXTRUDER and LIN_ADVANCE 2017-05-25 08:06:27 -05:00
Scott Lahteine 735405b2a4 Merge pull request #6848 from thinkyhead/bf_scara_M665
Add M665 for SCARA
2017-05-24 20:51:51 -05:00
Scott Lahteine ffa901f373 Merge pull request #6839 from thinkyhead/bf_day_ending_in_y
UBL ultralcd.cpp patches
2017-05-24 17:55:44 -05:00
Scott Lahteine 361cbba113 Use M665 to set SCARA angle offsets 2017-05-24 17:49:24 -05:00
Scott Lahteine 5ed63a5724 Apply const in prepare_kinematic_move_to 2017-05-24 17:49:24 -05:00
Scott Lahteine 5cbe0244c5 Fixes for spindle/laser and SCARA probe bounds 2017-05-24 17:49:23 -05:00
Scott Lahteine 1f52c9f5df Neater Megatronics 3 pins 2017-05-24 17:49:23 -05:00
Scott Lahteine af81cb4cbb Patch for M503 output 2017-05-24 17:49:09 -05:00
Scott Lahteine 1d167a6874 Some cleanup, fixes for ultralcd.cpp UBL code
- Free up 30 bytes of SRAM in UBL LCD code
- Fix BUILD_ABS_MESH temperature
- Fix UBL indentation in ultralcd.cpp
- UBL vars lowercase, "convert to positive" sensibly
2017-05-24 01:10:42 -05:00
Scott Lahteine f4028fe088 New GCode Parser - Implementation 2017-05-23 14:15:10 -05:00
Scott Lahteine 002a06c507 New GCode Parser - Configuration 2017-05-23 14:15:07 -05:00
Scott Lahteine ad915b667e One more mesh_index_to_npos update
Followup to #6827
2017-05-23 13:02:50 -05:00
Scott Lahteine 2881f0a48d Fix, extend G42 with P (probe) parameter
- Also fix handling of SCARA and misuse of `codenum`.
2017-05-23 04:55:42 -05:00
Scott Lahteine d252d1b6a2 Merge pull request #6831 from thinkyhead/bf_move_g7
Move G7 to G42
2017-05-23 03:02:57 -05:00
Brian 82ca6248e2 Move G7 to G42
See: #6777
2017-05-22 23:21:35 -05:00
Scott Lahteine 26ffa558a3 Use redraw flag for both types of LCD 2017-05-22 18:34:54 -05:00
Scott Lahteine 3ff7515527 Merge pull request #6817 from cbusillo/patch-1
missing enable for M605 for duplication mode
2017-05-22 18:07:11 -05:00
Scott Lahteine 34cfbc90cd Use new attribute macros in more places 2017-05-22 17:38:58 -05:00
Scott Lahteine 85b967657e Embed G26/G29 in ubl class, with enhancements 2017-05-22 17:38:58 -05:00
Scott Lahteine c99bd69889 Apply const float & more 2017-05-22 17:38:36 -05:00
Scott Lahteine ad5638f78c Cleanup some fastio code 2017-05-22 17:38:36 -05:00
Scott Lahteine e271521c39 Single user_canceled function in G26 2017-05-22 17:38:36 -05:00
Scott Lahteine c2ea22da49 Clean up whitespace 2017-05-22 17:38:36 -05:00
Scott Lahteine ceb62fc7e1 Fixes #6828: M428 bug 2017-05-22 17:34:03 -05:00
oldmcg 48f7652143 UBL G29 -P3.1 smart fill (#6823)
* UBL G29 -P3.1 mesh fill with distance-weighted least squares fit.

* Back to original -O0 on G29 for now.
2017-05-22 12:33:50 -05:00
Scott Lahteine 850203fb3a Merge pull request #6816 from thinkyhead/bf_lcd_live_editing
Constrain LCD status message rendering
2017-05-22 11:15:35 -05:00
Roxy-3D 3129260c44 Misc. Clean Up (#6822)
* Misc. Clean Up

Mostly UBL related clean up.
- But fixed a bug in the thermistortables.
- Made G26 more responsive to user aborts.
- Added sanity checks for older name for UBL_MESH_VALIDATION.
- Made G29 P4 able to edit invalidated mesh points
- Restore a reasonable Fade Height for UBL when creating new state information
- Get UBL's Topology Map to look a little bit better
- Make sure the user doesn't see a blank screen when doing Mesh Editing.

* Huh???   GitHub Desktop screwed up!

* get the planner object in scope

* Fix out of scope z_fade_height

* Travis timed out...

I need a change so I can force a new commit and sync.
2017-05-21 22:09:51 -05:00
cbusillo 3b4116e73b missing enable for M605 for duplication mode
I believe gcode_M605 will not be called when using DUAL_NOZZLE_DUPLICATION_MODE without this change.
2017-05-21 13:54:20 -04:00
Scott Lahteine 5e8892d6b5 Show Restore Failsafe item with EEPROM off 2017-05-21 12:52:44 -05:00
Scott Lahteine 76af9ac7c5 tweaks 2017-05-21 12:51:58 -05:00
Scott Lahteine ba5910ab6c Constrain LCD status message rendering 2017-05-21 12:35:16 -05:00
MagoKimbra 2c309a8f7c Fix set_lcd_contrast 2017-05-21 19:01:44 +02:00
Scott Lahteine 22dbb2117c Merge pull request #6812 from thinkyhead/bf_day_ending_in_y
Cleanup code, organize & document fastio pin mappings
2017-05-21 11:39:04 -05:00
Roxy-3D 364f8fb613 Update Configuration.h files to better names (#6814)
Changed UBL_G26_MESH_EDITING to UBL_G26_MESH_VALIDATION
Added UBL_MESH_EDIT_MOVES_Z to prepare for that change (coming next)
2017-05-21 11:10:22 -05:00
Scott Lahteine d7fda2fe49 Formatting, const in G33 2017-05-21 10:40:05 -05:00
Scott Lahteine 1519b0e7c1 Split up fastio.h, document pin mappings 2017-05-21 10:33:27 -05:00
Scott Lahteine 49599caade General cleanup to utf_mapper.h 2017-05-21 10:33:27 -05:00
Scott Lahteine 02f15f6775 UBL-related cleanup, spacing, standards
Reference: #6804
2017-05-21 10:33:26 -05:00
Scott Lahteine 52e20aeab3 Pins-related cleanup, formatting 2017-05-21 07:18:03 -05:00
Scott Lahteine ea906e4da7 Merge pull request #6810 from thinkyhead/bf_lcd_live_editing
Add "live editing" option to LCD menus
2017-05-21 06:11:52 -05:00
Scott Lahteine 11fc9564c9 Add live editing option to LCD menu 2017-05-21 05:29:46 -05:00
Scott Lahteine 8a0a5cfccc Temp-related cosmetic changes 2017-05-21 04:49:25 -05:00
Scott Lahteine b29dbbd5e4 Use uint16_t for temps 2017-05-21 04:48:53 -05:00
Scott Lahteine ebcd1aaf88 Access hotend/bed temperatures as float 2017-05-21 04:46:31 -05:00
Scott Lahteine 6ce2b1ff4a G33 evolutionary changes 2017-05-20 19:23:39 -05:00
Scott Lahteine 3c061a9f9a UBL tabs, whitespace, spelling, etc. 2017-05-19 14:16:50 -05:00
Scott Lahteine 75badae2f8 Disable PROBE_MANUALLY for UBL
Plus some other UBL tweaks.
2017-05-19 07:13:18 -05:00
Scott Lahteine 94a4af1d7f Merge pull request #6773 from thinkyhead/bf_lcd_patch_e5
Patch LCD code for 5th extruder
2017-05-18 15:26:55 -05:00
Brian 01f452c37c Tweak Azteeg X3 PRO _pins.h so Viki2 will work for those without a case light.
- add comment explaining that the Panucatt Viki2 wiring diagram uses pin 44
2017-05-18 13:00:13 -04:00
Brian e09b4ce4a5 Add checking 2017-05-17 19:46:16 -04:00
Brian 13599a73c7 Add G7 gcode command to move between UBL mesh points
- can be augmented in the future to enable for other leveling systems

Quite simple, but did not want to modify `G1` as the additional checking would slow it down.

Tested & working.
2017-05-17 19:05:36 -04:00
Brian 43c24f0027 Fix recent regressions, &c.
- fix broken `M421` due to less-than-careful optimization
- add HOME_AFTER_DEACTIVATE define to advanced config so not everyone has to rehome after steppers are deactivated
- misc. cleanups (remove unused label, unused variables)
2017-05-17 17:21:46 -04:00
Scott Lahteine 3843a5151a Patch LCD code for 5th extruder, EEPROM reset 2017-05-17 15:33:51 -05:00
Scott Lahteine 6c064bb7d6 Some probe_pt error-handling 2017-05-17 15:33:51 -05:00
Brian 3370329751 Fix broken EEPROM save/load 2017-05-17 12:41:27 -04:00
Scott Lahteine f0fe26c411 Ensure Arduino.h and configs are included for serial.cpp 2017-05-17 05:07:35 -05:00
Scott Lahteine ffb5353294 Merge pull request #6738 from thinkyhead/bf_config_crc_rebase
Implement CRC16, develop mesh allocation table
2017-05-17 04:44:00 -05:00
Scott Lahteine e806e6419a Merge pull request #6768 from thinkyhead/rc_spindle_m3_m5
Spindle / Laser support
2017-05-17 04:39:32 -05:00
Scott Lahteine d6f49c6626 Merge pull request #6752 from jdelahayes/bugfix-1.1.x
Update french language
2017-05-17 04:32:28 -05:00
Scott Lahteine 55a87da036 SPINDLE/LASER implementation 2017-05-17 04:26:15 -05:00
Scott Lahteine ffe0e2d19a SPINDLE/LASER pins changes 2017-05-17 04:23:06 -05:00
Scott Lahteine 99c4900a98 SPINDLE/LASER config changes 2017-05-17 04:23:06 -05:00
Scott Lahteine a3abfeac47 Mark strings needing translation 2017-05-17 03:49:33 -05:00
Scott Lahteine 7f4e4b1212 UBL name/state methods 2017-05-17 03:49:32 -05:00
Brian 7852369987 Implement CRC16, develop mesh allocation table
- Add crc16 utility function
 - Implement CRC16 for config store, remove old checksum, increment layout version
 - Move UBL mesh store/load to MarlinSettings; increment UBL_VERSION
 - Begin to lay out MAT structure, prototype functions, etc.
 - Rename ubl.state.eeprom_storage_slot to .storage_slot
 - Misc. optimization
 - Cleanup/standardize/improve some messages

This is a work in progress!
2017-05-17 03:49:19 -05:00
Scott Lahteine 00d358d92d Fix a PROBE_MANUALLY bug in ultralcd.cpp 2017-05-17 03:49:19 -05:00
fixoid c2321b1cdd Separate SWITCHING_NOZZLE and SWITCHING_EXTRUDER 2017-05-16 19:25:17 -05:00
Scott Lahteine 238fb53617 Patch home_all_axes to ignore G28 XYZ parameters 2017-05-16 16:18:38 -05:00
Scott Lahteine 6b6630e11b Clean up trailing whitespace and tabs 2017-05-16 16:06:18 -05:00
Roxy-3D d30e478f97 Fix incorrectly optimized find_closest_mesh_point_of_type() function (#6761) 2017-05-16 15:24:24 -05:00
oldmcg 5a9e52a3e0 Use COPY_XYZE macro to copy exactly 4 elements (#6758)
Fix undefined DELTA_PROBEABLE_RADIUS for UBL_DELTA
2017-05-16 11:47:51 -05:00
Roxy-3D 8606644343 M48 Fix for Delta Configuration Files & UBL G29 only homes when necessary (#6757)
* Fix M48 for Delta's  There was a scope issue: DELTA_PROBEABLE_RADIUS wasn't getting defined.

* Check if the specified G29 command requires homing
2017-05-16 11:23:50 -05:00
Tannoo 0cd398c25d UBL Menu Updates (#6751)
Things should be pretty stable for a while.   
But it wouldn't surprise me if the Delta people have a need for a few special commands.
2017-05-16 08:45:31 -05:00
Johann Delahayes a5737cba7c Update french language 2017-05-16 12:27:42 +02:00
Scott Lahteine 0fef9a2983 Remove "ubl." prefix from calls within ubl method 2017-05-16 01:19:45 -05:00
Scott Lahteine 14a4257c7b UBL tabs, whitespace, spelling, etc. 2017-05-16 01:19:45 -05:00
Scott Lahteine 56e2e331ed UBL G29: replace 'O' with 'T'
Since we already used 'T' for `G29` Topology Report in the past, and since 'T' is available…
2017-05-16 01:18:41 -05:00
Scott Lahteine 091f94a6bf Fix up M421 and some comments 2017-05-16 01:14:03 -05:00
Scott Lahteine 4ec4ecff1a Reduce find_closest_mesh_point_of_type a little 2017-05-16 01:14:03 -05:00
Scott Lahteine f1a1c6873e Patch lcd_implementation_status_screen compiler warning 2017-05-16 00:59:50 -05:00
moebyusDev 2266c0780d fixed spanish lang
It was missing MSG_FILAMENT_CHANGE_HEAT_2 and MSG_FILAMENT_CHANGE_HEATING_2
2017-05-16 00:35:36 -05:00
oldmcg b213a45efb UBL_DELTA post merge cleanup (#6705)
* UBL_DELTA post merge cleanup:
   fix fade_height, lost during some previous merge
   fix float cx,cy which are not const
   move repeated z_cxcy calc line inside loop
   style fixes and comment fixes/alignment

* Update ubl_motion.cpp

remove unnecessary parentheses

* Update Conditionals_post.h

Change name of define to more accurate meaning:
UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN
which is not and should not be the default for cartesians with UBL.
2017-05-16 00:30:29 -05:00
Roxy-3D 6f86c46fa6 Fix typo that caused scope issues for DELTA (#6750) 2017-05-15 23:13:45 -05:00
Roxy-3D 1fbcbc05f6 UBL no longer flout's the sacred GCode standard (#6745)
Also clean up ubl_motion.cpp debug info and fix declaration of cx & cy
2017-05-15 16:25:01 -05:00
Scott Lahteine c262ea92e0 Merge pull request #6733 from abusca/Euskera
Updated Basque translation
2017-05-15 02:30:11 -05:00
Scott Lahteine 267f77b18b More constraint on axis_unhomed_error 2017-05-14 16:03:02 -05:00
Aaron Busca 645096b87a Updated Basque translation
Updated Basque translation with new strings.
2017-05-14 18:29:50 +02:00
Roxy-3D 40d95a4e23 Update the gMax files to display better with Proportional Fonts (#6727)
Update the gMax files to display better with Proportional Fonts
2017-05-13 16:33:04 -05:00
Roxy-3D c06af63f87 G26's default behaviour ought to be the entire mesh (#6726)
Adding the capability to specify ahead of time how much of the validation pattern to print made it so by default G26 only did one circle and no connecting lines.

It is more natural for the unsophisticated user to just do the entire mesh (bed).   We default the repetition count to GRID_MAX_POINTS+1 to insure we get every last one of them!
2017-05-13 15:53:44 -05:00
Roxy-3D 15040821e0 Setup FolgerTech-i3-2020 files better for the user (#6724)
UltiPanel was enabled, but technically, it is a REPRAP_DISCOUNT_SMART_CONTROLLER
Either configuration works on the machine.  But we want it 'Right'.

Setup the Proportional Font spacing so columns line up nicer on PronterFace and Repetier Host.
2017-05-13 15:14:03 -05:00
Scott Lahteine 67c9b1e332 Update M665 comment, fix M665 code_value code. 2017-05-13 05:11:29 -05:00
Scott Lahteine 37399e3cb5 Fix prepare_move_to_destination_cartesian for UBL 2017-05-13 04:13:19 -05:00
Scott Lahteine a7fb55ea6d Use GRID_MAX_POINTS. Some formatting 2017-05-12 06:57:19 -05:00
Scott Lahteine e51b5774db Merge pull request #6699 from mtowara/patch-1
Bugfix PRINTER_EVENT_LEDS
2017-05-12 05:58:25 -05:00
Scott Lahteine 056350d9bf Merge pull request #6656 from FHeilmann/fix_fwretract_pos_z_move
Fix FWRetract with positive z-moves during retracted state
2017-05-12 05:56:08 -05:00
Scott Lahteine 0e582bcfb7 Fix #6691 - redundant line in M665 2017-05-12 05:17:38 -05:00
Markus Towara 68ae7c8d7a Bugfix PRINTER_EVENT_LEDS
Extra closing curly bracket terminates while loop early if PRINTER_EVENT_LEDS defined
2017-05-12 12:13:23 +02:00
Scott Lahteine ba29da56e0 Add disclaimer for verboten parameters 2017-05-12 02:34:53 -05:00
Scott Lahteine 0696dda470 Cleanups to UBL_DELTA 2017-05-12 02:34:53 -05:00
Scott Lahteine cbfca29522 M421 tweaks, just to use const 2017-05-12 01:32:34 -05:00
Scott Lahteine 233f824dd6 Define GRID_MAX_POINTS 2017-05-12 01:32:34 -05:00
Scott Lahteine b17e2d3dcd Apply const in Marlin_main.cpp 2017-05-12 01:32:33 -05:00
Scott Lahteine 92fbea2906 Add some GCodes to the header of Marlin_main.cpp 2017-05-12 01:32:33 -05:00
Scott Lahteine 94e90ca26c Tweak M80/M81 descriptions 2017-05-12 01:32:33 -05:00
Scott Lahteine ee50dfaaf3 Adjust G26 arguments 2017-05-12 01:32:33 -05:00
Scott Lahteine b0ba5cae73 Fix a spelling boo 2017-05-12 01:32:33 -05:00
oldmcg 91841d75c9 UBL_DELTA (#6695)
UBL on Delta's....     Should be close!    Should not affect any Cartesian printer.
2017-05-11 22:33:47 -05:00
bgort 445003dbb8 Merge pull request #6694 from bgort/g29p2b
UBL:  Minor improvement to G29 P2
2017-05-11 20:44:43 -04:00
Brian 5a5dba6fc8 UBL: Minor improvement to G29 P2
- allow H code value to override probing height
- minor cleanups
2017-05-11 18:54:34 -04:00
Brian ae676490c9 M421: Add 'adjust closest point' capability
- Split M421 into separate versions for bilinear and ubl
- Fix minor issue in G26
2017-05-11 12:10:38 -04:00
Scott Lahteine 9a688d1456 Merge pull request #6682 from thinkyhead/bf_M80_s_arg
"M80 S" to report the state of the PSU pin
2017-05-10 20:29:01 -05:00
Roxy-3D b63e82f309 M421 Mesh Point Offset and misc. UBL clean up (#6685)
* M421 Mesh Point Offset and misc. UBL clean up

Allow M421 to accept an offset as well as absolute value for a specified
mesh point.
And misc. UBL clean up to reduce redundent code.

* Better error checking for M421

* Fix M421 Y index bug

I just noticed....  We've had a Y index bug for who knows how long?
2017-05-10 18:54:10 -05:00
Pablo Ventura 539e0c2f31 "M80 S" to report the state of the PSU pin 2017-05-10 17:58:58 -05:00
bgort df42428281 Merge pull request #6665 from bgort/font
Add proportional font adjustment ratio
2017-05-10 17:30:51 -04:00
Brian 2604742191 Add proportional font adjustment ratio
- update example configs
2017-05-10 17:19:03 -04:00
bgort b3407a371b Merge pull request #6676 from bgort/g26zhop
G26: Add 0.5mm Z-bump between circles to minimize pattern scraping
2017-05-10 17:12:05 -04:00
bgort c33d99c5b2 Merge pull request #6680 from bgort/g26repeat
G26:  Add 'Repeat' Option
2017-05-10 17:11:34 -04:00
Bob-the-Kuhn 7325035aac Merge pull request #6637 from Tannoo/UBL_Menu_System_1.1
UBL Menu System 1.1
2017-05-10 15:54:48 -05:00
Brian f7a201b0d0 G26: Add 'Repeat' Option
- Allows for specifying number of points to print/validate, using 'R' code like with G29 P4 Rx
- Moved the code for Random to 'M' so we could be consistent with G29 P4
- G26 instructions indenting/cleanup
2017-05-10 16:52:08 -04:00
Brian 9c5957fc77 G26: Add 0.5mm Z-bump between circles to minimize pattern scraping 2017-05-10 16:11:59 -04:00
Brian 4da14b14f4 UBL Cleanup/Bugfix
- Fix bug in ubl_line_to_destination
- Improve/fix output of some ubl.h functions
2017-05-10 13:56:17 -04:00
Tannoo 66db6c3acc UBL Menu System 1.1
/**
     * UBL System submenu
     *
     *  Prepare
     * - Unified Bed Leveling
     *   - Activate UBL
     *   - Deactivate UBL
     *   - Mesh Storage
     *       Memory Slot:
     *       Load Bed Mesh
     *       Save Bed Mesh
     *   - Output Map
     *       Map Type:
     *       Output Bed Mesh Host / Output Bed Mesh CSV
     *   - UBL Tools
     *     - Build Mesh
     *         Build PLA Mesh
     *         Build ABS Mesh
     *       - Build Custom Mesh
     *           Hotend Temp:
     *           Bed Temp:
     *           Build Custom Mesh
     *         Info Screen
     *       - Build Cold Mesh
     *       - Fill-in Mesh
     *           Fill-in Mesh
     *           Smart Fill-in
     *           Manual Fill-in
     *           Info Screen
     *         Continue Bed Mesh
     *         Invalidate All
     *         Invalidate Closest
     *     - Validate Mesh
     *         PLA Mesh Validation
     *         ABS Mesh Validation
     *       - Custom Mesh Validation
     *           Hotend Temp:
     *           Bed Temp:
     *           Validate Mesh
     *         Info Screen
     *     - Edit Mesh
     *         Fine Tune All
     *         Fine Tune Closest
     *       - Adjust Mesh Height
     *           Height Amount:
     *           Adjust Mesh Height
     *         Info Screen
     *     - Mesh Leveling
     *         3-Point Mesh Leveling
     *       - Grid Mesh Leveling
     *           Side points:
     *           Level Mesh
     *         Info Screen
     *   - Output UBL Info
     */
2017-05-10 12:14:43 -05:00
Brian 3b0127cf8e Fix compiler complaint related to M100 2017-05-09 21:45:44 -04:00
Scott Lahteine 11104f177b Apply const in BABYSTEPPING 2017-05-09 12:37:23 -05:00
Scott Lahteine 081bf1f879 Patch #else / #endif comments 2017-05-09 12:37:23 -05:00
Scott Lahteine a9487c9443 Reduce redundancy in BLTOUCH conditionals 2017-05-09 11:52:24 -05:00
Scott Lahteine 8d961b51cc Eliminate M100 compiler warnings? 2017-05-09 11:32:15 -05:00
bgort efb9ce24d9 Merge pull request #6645 from tcm0116/bltouch_config
Automatically define Z_MIN_PROBE_ENDSTOP_INVERTING for BLTouch
2017-05-09 09:49:16 -04:00
bgort e2f07917ab Merge pull request #6644 from tcm0116/bltouch_menu
Move BLTouch LCD menu from Main to Main/Control
2017-05-09 09:49:02 -04:00
Florian Heilmann fe96376a73 Fix FWRetract with positive z-moves during retracted state 2017-05-09 13:54:57 +02:00
Scott Lahteine 47cae2929f Patch platformio.ini to fix build error in DevIoT
For compatibility with DevIoT, until that can be solved.
2017-05-08 20:27:14 -05:00
Scott Lahteine 911a87e006 Disable SCARA feedrate scaling by default 2017-05-08 14:41:03 -05:00
Scott Lahteine 71396f77d3 Cleanups following recent commits 2017-05-08 14:23:01 -05:00
Scott Lahteine dca48f0e63 Move platformio.ini back to Marlin folder - it works there 2017-05-08 14:23:01 -05:00
Scott Lahteine a6dafb058e Small reduction in error code size 2017-05-08 13:58:09 -05:00
Scott Lahteine a1e04942a2 Cleanup to software PWM variables 2017-05-08 13:51:45 -05:00
Thomas Moore a20d0794e6 Automatically define Z_MIN_PROBE_ENDSTOP_INVERTING for BLTouch 2017-05-08 16:28:44 +00:00
Thomas Moore 3279337f47 Move BLTouch LCD menu from Main to Main/Control 2017-05-08 15:21:01 +00:00
Brian 6cb0fa4128 Cleanup previous implementation of new quiet probing
Saves a few lines of code.
2017-05-08 08:13:46 -04:00
bgort 4b7f8ad9c6 Merge pull request #6610 from bgort/pio-improvements2
PlatformIO-related changes
2017-05-08 07:52:42 -04:00
Scott Lahteine 56ca47ab9d Patch configuration temp units 2017-05-07 21:32:01 -05:00
Scott Lahteine 421dd62800 Adjust spacing of "spaces" 2017-05-07 21:28:54 -05:00
Scott Lahteine 26dba44cd3 Patch redundant lcd settings 2017-05-07 21:28:54 -05:00
Scott Lahteine 34b5041576 Spacing adjustment, ubl_G29 2017-05-07 21:28:54 -05:00
Scott Lahteine 1c4ed8b106 Note 5 extruders in config comments 2017-05-07 21:28:54 -05:00
Scott Lahteine 6e4a5cc8c6 Patch missing const in temp_abs 2017-05-07 21:13:44 -05:00
bgort d35e2fda10 Merge pull request #6622 from bgort/silentprobing
Improve BLTOUCH_HEATERS_OFF functionality
2017-05-07 21:33:44 -04:00
Scott Lahteine 6ed52fb765 Adjust spacing in LSF 2017-05-07 19:11:52 -05:00
Roxy-3D 110afff415 More misc UBL fixes and update gMax examples (#6632)
I think I forgot to Sync before I committed last time.   Some UBL
changes did not stick.

Also, update the gMax configuaration.h file so other than unique numbers
and settings, it exactly matches the default configuration.h file.
2017-05-07 19:02:24 -05:00
Roxy-3D d92fa40c62 misc. UBL fixes (#6631)
* Restore LSF functionality

Some of the typo's persisted...   Hopefully this gets them all fixed.

* Restore user's expectations of how G28 should behave

* Allow Nozzle size control with ornery host programs
2017-05-07 18:23:48 -05:00
Brian faa270071d Improve BLTOUCH_HEATERS_OFF functionality
- rename to PROBING_HEATERS_OFF
 - move heater pausing functionality into thermalManager
   - add variables, pause(), ispaused(), other functions
 - add fan pausing functionality -> PROBING_FANS_OFF
 - add probing_pause() wrapper
 - move pausing into do_homing_move() and do_probe_move() to minimize quiet time and so other probe types can benefit
 - example configs
2017-05-07 16:22:08 -04:00
lrpirlet d66e9efac5 G29 P1 stops reporting Invalid location with this patch 2017-05-07 15:07:26 +02:00
Scott Lahteine ce507deb9f Support temperature units in M503 2017-05-06 20:24:51 -05:00
bgort a59066bca9 Various improvements - mostly UBL-related (#6607)
UBL Clean up.
2017-05-06 18:59:16 -05:00
Brian 0446dd3ad8 PlatformIO-related changes
- move platformio.ini out of source directory to be more consistent with 'normal' PlatformIO usage
  - facilitates IDE integration
- add related .gitignores
2017-05-06 06:22:10 -04:00
Scott Lahteine 77769e284f Edit configuration comments 2017-05-05 13:32:31 -05:00
Scott Lahteine 6876e79d42 Tweak command index increment 2017-05-05 13:32:31 -05:00
Scott Lahteine 7fcb5c1424 Minor fix in K8200 readme 2017-05-05 11:25:11 -05:00
Max Matveev 267f3a03d9 Fixed USE_CONTROLLER_FAN #define usage 2017-05-04 23:38:29 +02:00
bgort ae7c602031 fix error in M105 output -- use SERIAL_PROTOCOL for ints instead of SERIAL_PROTOCOL_F (#6584)
also removed wayward 'address of' ampersand in setTargetHotend and setTargetBed parameters
2017-05-04 16:09:45 -05:00
Scott Lahteine 3cd9af2409 bugfix-1.1.x ReadMe, Version, helper scripts 2017-05-04 07:17:10 -05:00
Florian Heilmann 15268770f5 Fix broken fwretract recovery extruder feedrate
When both lowering and recovery are performed using the same "prepare_move_to_destination()" the extruder recovery feedrate ends up being ignored and, instead, is only capped by either the maximum e-speed or the time it takes to perform the z-lowering. 
Performing the two moves separately from each other ensures a correct recovery feedrate.
2017-05-04 11:34:28 +02:00
Scott Lahteine 58210c3a19 Merge pull request #6568 from thinkyhead/rc_bilinear_extension
Add EXTRAPOLATE_BEYOND_GRID option to bilinear leveling
2017-05-04 00:46:05 -05:00
Scott Lahteine da08e11acd Add EXTRAPOLATE_BEYOND_GRID option to bilinear leveling 2017-05-04 00:19:07 -05:00
Scott Lahteine 6834e36871 Merge pull request #6567 from thinkyhead/rc_sdcard_stop
Shutdown heaters, autotemp on SD Cancel
2017-05-03 23:54:29 -05:00
Scott Lahteine 399efd66ed Click to resume 2017-05-03 22:26:06 -05:00
Scott Lahteine 1196e3ca59 SDCard print completion can use "M0" 2017-05-03 22:24:03 -05:00
Scott Lahteine 6854f08d22 Shut down autotemp in disable_all_heaters 2017-05-03 20:54:26 -05:00
Thomas Moore acec237092 Shutdown heaters and fan after canceling a print from the SD card 2017-05-03 20:43:09 -05:00
Scott Lahteine 11b6a3cbb6 Fix regression in least_squares_fit.cpp 2017-05-03 19:21:44 -05:00
Scott Lahteine e1b85ff67b Merge pull request #6559 from thinkyhead/rc_more_optimal
Compact smart_fill_mesh slightly
2017-05-03 19:07:36 -05:00
Scott Lahteine 9890141f7b M100 tweak 2017-05-03 17:28:09 -05:00
Scott Lahteine 2658cc707a Treat temperature as integer, when possible 2017-05-03 17:27:25 -05:00
Scott Lahteine 1b2c7ec20a Make G26 compatible with inches and thermal unit modes 2017-05-03 17:12:48 -05:00
Scott Lahteine 241bdffe65 Dress up Bilinear Leveling code 2017-05-03 17:12:35 -05:00
Scott Lahteine 67ecf06cc4 Patch issue in gcode_M900
Noted in #6550
2017-05-03 15:26:00 -05:00
Scott Lahteine de5e485ed7 Explicit upward angle solution 2017-05-03 01:19:44 -05:00
Scott Lahteine ecdf68735f Compact smart_fill_mesh slightly 2017-05-03 01:06:58 -05:00
Scott Lahteine 628391304f Merge pull request #6552 from thinkyhead/rc_more_ubl_cleanup
Further cleanup of UBL
2017-05-02 22:46:04 -05:00
Scott Lahteine 902fe76db9 Merge pull request #6556 from thinkyhead/rc_use_controller_fan
Implement USE_CONTROLLER_FAN as a feature
2017-05-02 22:43:26 -05:00
Scott Lahteine 7ba7474a73 Drop extra parens from address-of operator 2017-05-02 22:22:23 -05:00
Scott Lahteine 0bf5add075 Use UBL_MESH_(MIN|MAX)_[XY] for G29 move limits 2017-05-02 22:22:23 -05:00
Scott Lahteine b8ba3b7647 Use 'sq' macro where possible 2017-05-02 22:22:23 -05:00
Scott Lahteine 66eba3346b Remove G29 lcd control debugging 2017-05-02 22:22:23 -05:00
Scott Lahteine 3517154135 Reduce code size, fix bug in smart_fill_mesh 2017-05-02 22:22:23 -05:00
Scott Lahteine c4e34adcf1 Apply formatting, coding standards to UBL 2017-05-02 22:22:23 -05:00
Scott Lahteine f4239e62b1 Merge pull request #6557 from thinkyhead/rc_hotend_status_item
Keep refreshing LCD if hotend status is on-screen
2017-05-02 22:04:21 -05:00
Scott Lahteine fc857c5b78 Merge pull request #6549 from thinkyhead/rc_bltouch_refix
Fix BLTOUCH_HEATERS_OFF bug
2017-05-02 21:53:09 -05:00
Thomas Moore b39f634252 Continuously update LCD when hotend status is displayed in Filament Change screens 2017-05-02 21:49:40 -05:00
Scott Lahteine 2c13922c46 Implement USE_CONTROLLER_FAN as a feature 2017-05-02 20:18:52 -05:00
Scott Lahteine 492bc536bf Modify debug methods to take PSTR 2017-05-02 17:53:40 -05:00
Bob-the-Kuhn e5a27d9f36 G29 P2 & P4 bug fixes & improvements 2017-05-02 17:53:40 -05:00
Scott Lahteine b93be716cf Remove trailing whitespace 2017-05-02 17:53:40 -05:00
Scott Lahteine 76eca9732d Fix mis-named language string define in Dutch 2017-05-02 16:08:09 -05:00
Scott Lahteine 806f670092 Merge pull request #6511 from Bob-the-Kuhn/UBL--G26-minor-improvements
UBL: G26 minor improvements
2017-05-02 16:06:22 -05:00
Scott Lahteine 0803c9d997 Merge pull request #6533 from thinkyhead/rc_autocal_patches
General cleanup of G33
2017-05-02 16:01:02 -05:00
Brian ff5fed137f Fix BLTOUCH_HEATERS_OFF bug 2017-05-02 15:53:52 -05:00
Scott Lahteine ca1dd739a3 Organize ubl.h defines by the files they serve 2017-05-02 15:47:06 -05:00
Scott Lahteine 0449f69179 Cleanup patch to recent merge 2017-05-02 15:47:06 -05:00
LVD-AC da2abad636 Various cleanups of G33
- update comment section
- redefined P5 grid
- minor clean to probe radius routine
- updated EEPROM version to V37 according remark in #6517
2017-05-02 15:47:06 -05:00
Bob-the-Kuhn 7ce613db0a Fix Conditionals test for endstop plug used by Z2 or probe. 2017-05-02 15:41:47 -05:00
Scott Lahteine ef750ae86b Towards supporting Z2 in Endstops::report_state 2017-05-02 15:39:32 -05:00
Scott Lahteine c03c623951 Sanity-check Z2 endstop assigned to a nonexistent pin. 2017-05-02 15:39:00 -05:00
Scott Lahteine 70f31b6c76 Throw an error if no E stepper is free for X2, Y2, Z2 2017-05-02 15:13:47 -05:00
Scott Lahteine ac69eca586 Merge pull request #6538 from bgort/ubl_gridlbls
Fix, cleanup, prettify `G29 O` output
2017-05-02 14:09:18 -05:00
Scott Lahteine 99b11db1a1 Merge pull request #6537 from thinkyhead/rc_cleanup_sunday
Various leveling-related patches
2017-05-02 00:59:59 -05:00
Roxy-3D 41e63bbb7c Fix Horizontal and Vertical UBL optimization bug. (#6540)
* Fix Horizontal and Vertical optimization bug.

And drastically reduce the debug code foot print....

* Yeah Baby!

The debug print is going A - OK !
2017-05-01 23:52:33 -05:00
Scott Lahteine e79b335367 Patches for leveling reactivation in G28 / M48 2017-05-01 17:38:57 -05:00
Brian 92e22c3bf2 Fix, cleanup, prettify G29 O output 2017-05-01 18:19:57 -04:00
Scott Lahteine 7d5cd7e0d7 Tweak set_bed_leveling_enabled 2017-05-01 16:46:52 -05:00
Scott Lahteine ed81e9b3d3 Adjust leveling conditionals 2017-05-01 16:46:48 -05:00
Scott Lahteine a64e5659ce Clean up G26 external references, private vars 2017-05-01 15:17:52 -05:00
Scott Lahteine 2887c20788 Add a function to home all axes (i.e., gcode_G28) 2017-05-01 15:03:37 -05:00
Scott Lahteine 8f895d5e01 Merge pull request #6530 from thinkyhead/rc_cleanups_2
Fixes for DUAL_NOZZLE_DUPLICATION_MODE
2017-05-01 12:34:11 -05:00
Scott Lahteine 8002672938 Fixes for DUAL_NOZZLE_DUPLICATION_MODE 2017-05-01 12:20:25 -05:00
Scott Lahteine f69acde966 Merge pull request #6528 from MarlinFirmware/revert-6416-negative-mesh-fix
Revert "Fix for Meshpositions if printer has negative endstop positions"
2017-05-01 11:51:13 -05:00
Scott Lahteine 4803a4322e Revert "Fix for Meshpositions if printer has negative endstop positions" 2017-05-01 11:25:07 -05:00
Scott Lahteine 4f74c416a4 Patch for BLTOUCH_HEATERS_OFF 2017-05-01 11:13:40 -05:00
Scott Lahteine 1823a6ea29 Patch for missing DELTA_HEIGHT 2017-05-01 11:05:35 -05:00
Scott Lahteine d814e468d2 Fix set_heaters_for_bltouch and usage
- Only call `set_heaters_for_bltouch` when actually deploying/stowing
- Clear `next_emi_protection` when re-enabling heaters
2017-05-01 02:27:52 -05:00
Brian 4e1448e75a Various fixes for compiler warnings
add BLTouch-related messages in english and (rusty) french;
add missing endstops.h in ultralcd.cpp;
fix misc. compiler warnings;
fix lsf_reset - ZERO macro can't handle a pointer as it would only memset the size of the pointer, not the size of the entire struct
2017-05-01 02:12:40 -05:00
Scott Lahteine fc9919b749 Merge pull request #6515 from thinkyhead/rc_cleanup_sunday
Some minor cleanups to code formatting
2017-04-30 22:58:16 -05:00
Scott Lahteine c12bc51a59 cardreader.cpp spacing tweak 2017-04-30 22:27:47 -05:00
Scott Lahteine 46b714a52f Cleanup spacing in pinsDebug.h 2017-04-30 22:27:26 -05:00
Scott Lahteine 88141ca717 Remove things that aren't pins from pinsDebug_list.h 2017-04-30 22:24:51 -05:00
Scott Lahteine ff35b11d08 Resolve compiler complaint about memset volatile * 2017-04-30 22:24:03 -05:00