Richard Wackerbarth
0cebe85e65
Clean up spacing and duplicate entries
...
• Removing trailing whitespace
• Adjusting indention for better readability
• Removing duplicated entries
2015-12-10 07:20:52 -06:00
Richard Wackerbarth
e7b40bbe98
Change link to U8glib source
2015-12-10 06:33:29 -06:00
Richard Wackerbarth
e2da2b4105
Back port language translation
2015-12-10 06:31:41 -06:00
Richard Wackerbarth
4f314afaf0
Allow Thermistor #12 to be used on hotends also
...
//100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
Caveat Emptor —-
I’m not sure that this really makes sense,
but why keep someone from using it?
2015-12-10 06:31:31 -06:00
Scott Lahteine
60d5658da8
Revert nozzle_bed_fan_menu_items
...
For some reason that I cannot determine, using a sub-function causes
the Tune sub-menu to act strangely, yet replacing the function call
with its code content works perfectly.
2015-12-09 20:33:52 -06:00
AnHardt
57da1b8497
Host parseble output for M109, M190 and M303
...
Make the output of M105 more similar to Repetier.
Make the text-print pert of M105 an extra function to make it reusable. `print_heaterstates()`
Use `print_heaterstates()` in M019, M190 and M303
2015-12-07 15:37:53 -06:00
AnHardt
fcceb98191
Unglobalize no_wait_for_cooling
2015-12-07 15:34:26 -06:00
Wurstnase
78a347a01a
change nx, ny, nz and ne from float to long
...
st_set_position takes long
```void st_set_position(const long& x, const long& y, const long& z, const long& e)```
2015-12-07 08:22:44 -06:00
Wurstnase
6d691aceee
change dx, dy, dz and de from float to long
...
anything is long, we don't need float there
2015-12-07 08:22:24 -06:00
Richard Wackerbarth
6bfcb74c25
The probe stowing coordinates have changed
2015-12-05 19:31:59 -06:00
Wurstnase
0fbfb22506
Renaming delta speeds (PR2824)
...
dx -> dsx
dy -> dsy
dz -> dsz
de -> dse
2015-12-04 07:55:45 -06:00
AnHardt
8d1eeff021
Fix status LEDs update when reinitializing the display
...
Fix status LEDs update when reinitializing the display
By using the regular update function during init.
Fixing #2683
2015-12-03 07:18:35 -06:00
Richard Wackerbarth
5a54204f72
Marlin 1.1.0 Release Candidate 3 - 01 December 2015
2015-12-01 07:24:45 -06:00
AnHardt
bb4efcf603
Handle temp callbacks when THERMAL_PROTECTION_HOTENDS is not defined
...
by alternate definition for the callback macros
2015-12-01 07:21:52 -06:00
AnHardt
96d0d04b8f
Update LCD buttons less frequently
...
Move slow_buttons_update into the LCD_UPDATE_INTERVAL block
lcd_implementation_read_slow_buttons() will then be executed ~10 times a
second.
2015-11-30 05:44:32 -06:00
Richard Wackerbarth
e293ea57f0
Unbalanced brackets in setPwmFrequency
...
This is a back port of the correct in issue #248
2015-11-30 05:44:32 -06:00
AnHardt
c956b52c4a
Babystep Multiplier
...
Analog to https://github.com/MarlinFirmware/MarlinDev/pull/250 by
@RicardoGA
Restore the Babystep Multiplicator functionality and now it's available
for X/Y/Z
2015-11-30 05:43:10 -06:00
Richard Wackerbarth
956418c674
Kc is also a multi-PID parameter
2015-11-23 06:08:01 -06:00
AnHardt
33addc52a1
Suppress Z_MIN_PROBE_REPEATABILITY_TEST for DELTA and SCARA configurations (PR#2747)
...
For now Z_MIN_PROBE_REPEATABILITY_TEST is not possible for DELTA or SCARA
configurations.
This PR comments the feature out, where it is commented in by default.
2015-11-13 07:33:33 -06:00
AnHardt
8da2e98985
Split RAMPS 1.3 an 1.4 (PR#2741)
...
because of hardware differences on the SERVO0_PIN
2015-11-13 07:13:48 -06:00
AnHardt
be7167ed97
Change XY formatting on LCD (PR#2740)
...
According to #123 negative values for XY at or below -100 are displaying incorrectly, dropping the first digit. Deltas can easily have XY values in this range. This PR adds a function to display floats/ints formatted like `_123`, `-123`, `_-12`, or `__-1` as appropriate and applies it to the XY coordinates on Hitachi displays. It also moves the Z value to the right to be consistent with the XY formatting.
2015-11-13 06:46:11 -06:00
Luis Correia
e7099ea597
Fix Portuguese (Portugal) strings (PR#2700)
...
Align strings with release
2015-11-12 00:08:42 -06:00
Scott Lahteine
754b13d8fe
Patch issue #2315
2015-11-12 00:03:22 -06:00
Scott Lahteine
dbd4c17096
Init Kp, Ki, Kd to 0
2015-11-12 00:03:22 -06:00
Scott Lahteine
644c376e84
Use binary OR with endstop bits
2015-11-12 00:03:22 -06:00
Scott Lahteine
54a39d8c1a
Use a ternary in qr_solve.cpp
2015-11-12 00:03:22 -06:00
Scott Lahteine
17c23bbaf3
Shorten gcode_M221 yet function the same
2015-11-12 00:03:22 -06:00
Scott Lahteine
c0e791dbe9
Only look for "N" line number as first parameter
2015-11-12 00:03:22 -06:00
Scott Lahteine
b4af4441c5
Clean up watchdog impl.
2015-11-12 00:03:22 -06:00
Scott Lahteine
8f16563bbd
Use "defined" with LCD_PIN_BL and LCD_PIN_RESET
2015-11-12 00:03:22 -06:00
Scott Lahteine
6fa7e24af3
Use "UNUSED" to squash compiler warnings
2015-11-12 00:03:22 -06:00
Scott Lahteine
d5b7c595ae
Use static locals in utf_mapper.h
2015-11-12 00:03:21 -06:00
Scott Lahteine
9bdab4f3a8
Clean up "else" and other spacing
2015-11-12 00:03:21 -06:00
Scott Lahteine
9b23490f01
Clean up spacing in configs
2015-11-12 00:03:21 -06:00
esenapaj
c6c37abd41
Update language_kana.h
2015-11-12 00:00:51 -06:00
esenapaj
c24045475a
Update language_kana_utf8.h
2015-11-12 00:00:32 -06:00
Richard Wackerbarth
25d636c9e0
Compiler issues (PR#2696)
2015-11-11 23:52:11 -06:00
AnHardt
47401ec97b
MSG_EXTRUDER_SWITCHED_OFF was renamed to MSG_REDUNDANCY
...
in language.h, but was not renamed here. If TEMP_SENSOR_1 is enabled as redundant then
an error is thrown that MSG_EXTRUDER_SWITCHED_OFF is not defined.
Originaly by @12dstring
2015-10-08 10:45:11 -05:00
Scott Lahteine
ba6a243197
DEBUG message has no parameter (PR#2671)
2015-10-03 22:03:03 -05:00
Scott Lahteine
0c7f7ebcfb
Styling adjustments (PR#2668 & PR#2670)
...
Keep "astyled" reformatting
2015-10-03 22:02:45 -05:00
Rafa Couto
b5fb7075b9
Galician (gl) language.
2015-09-30 14:46:01 -05:00
Richard Wackerbarth
7b4bdc0203
DUAL_X_CARRIAGE motor enabling
...
As noted by @darkjavi et.al. in #103 , the E1 motor was not being enabled in planner.cpp when using DUAL_X_CARRIAGE. This patch enables and disables E1 as it should.
2015-09-30 04:31:19 -05:00
Richard Wackerbarth
91b5156b3e
Marlin 1.1.0 Release Candidate 2 - 29 September 2015
2015-09-29 20:28:41 -05:00
Richard Wackerbarth
03f0edb57e
Fix high LCD status screen update frequency (PR#2655)
2015-09-28 11:07:33 -05:00
KiteLab
0ad25c6665
Hint for changed behaviour of SDSUPPORT
2015-09-28 11:07:33 -05:00
Richard Wackerbarth
e01f5e1ef7
Cleanup
2015-09-17 10:44:23 -05:00
Mike Cochrane
5e36b64635
SDEXTRASLOW for some SD card readers (PR#176)
...
Add SDEXTRASLOW which runs the SD card at SPI_QUARTER_SPEED. Quarter speed is needed for RIGIDBOT_PANEL
2015-09-14 07:58:08 -05:00
Scott Lahteine
5d65a36dee
Give lcd_sd_status an UNKNOWN state (PR#180)
2015-09-14 06:32:27 -05:00
fmalpartida
0f149ea0c6
LCD home button causes repeated homing (PR#175)
...
Fix: increased debounce delay.
2015-09-14 06:31:49 -05:00
Scott Lahteine
b825567e0f
Drop www. from marlinfirmware.org (PR#175)
2015-09-14 06:28:53 -05:00
Scott Lahteine
db27e67580
Apply PID_ADD_EXTRUSION_RATE to extras
2015-09-12 07:53:20 -05:00
Scott Lahteine
bc50db9cf6
Implement PID_ADD_EXTRUSION_RATE
2015-09-12 07:53:20 -05:00
Scott Lahteine
cffb2d457e
Cleanup file formatting
2015-09-12 07:48:27 -05:00
Scott Lahteine
7ac7ddbf20
Show nozzles, heaters, and extruders numbered 1-4
2015-09-12 07:40:18 -05:00
Scott Lahteine
5bc480fee8
Fix Move E menu items
2015-09-12 07:33:49 -05:00
Scott Lahteine
fc882c34a3
Init lcd_sd_status as false to force lcd_update test
...
Replaces #145 which is way out of date
2015-09-12 07:32:20 -05:00
Scott Lahteine
e27dd5c22d
Conditionalize functions that rely on SDSUPPORT
2015-09-12 07:30:09 -05:00
Scott Lahteine
fabf3ae4a0
Add final Z raise after Delta probe
2015-09-12 07:23:24 -05:00
Petr Zahradnik
8c768a76a2
Create language_cz.h
...
Czech language translation.
2015-09-12 07:18:05 -05:00
Petr Zahradnik
5b9010965d
Update language.h
...
Added comment for Czech language (associated with file language_cz.h).
2015-09-11 04:43:54 +02:00
Scott Lahteine
89fb778684
Fix up probe pin define and test
2015-09-10 10:54:03 -05:00
Scott Lahteine
558665cd90
Constrain Tune > Nozzle/Flow menu items
2015-09-10 08:47:11 -05:00
Scott Lahteine
9f462f0cf5
Hack to address stuttering caused by ISR not finishing in time
...
(PR #138 )
When the ISR does not finish in time, the timer will
wrap in the computation of the next interrupt time.
This hack replaces the correct (past) time with a time not far in the future.
2015-09-10 08:26:17 -05:00
Scott Lahteine
8b3d63c423
Unify Delta XYZ homing rates
...
As noted in #130 allen key probe stow rate is based on homing rates,
but homing rates were left out of most delta configs. This unifies the
XYZ homing rates and applies the unified rates to allen key movements.
2015-09-08 13:11:55 -05:00
Scott Lahteine
7c72b57313
Unify manual feedrate and Fix LCD MANUAL_FEEDRATE (PR#128)
...
As noted by @o-lampe at https://github.com/MarlinFirmware/MarlinDev/issues/114#issuecomment-136757614 the `MANUAL_FEEDRATE` for Delta Z should be the same as XY.
2015-09-08 13:11:55 -05:00
Scott Lahteine
f690b82343
Remove extra MAX_FREQ_TIME define (PR#148)
2015-09-08 13:11:12 -05:00
Scott Lahteine
a4c78ae786
Add E1 pins to SENSITIVE_PINS for Dual Y or Dual Z
2015-09-07 09:41:06 -05:00
Scott Lahteine
a39fadf876
Update kossel-pro example config (again?)
2015-09-07 09:41:06 -05:00
Scott Lahteine
34e0a8d848
Move Y2 and Z2 pins defines to pins.h
2015-09-07 09:41:06 -05:00
Scott Lahteine
28599c51c7
Wrap Dual Y options in a conditional
2015-09-07 09:41:05 -05:00
Scott Lahteine
11a065c0ca
Remove Z2 pins overrides from Configuration_adv.h
2015-09-07 09:41:05 -05:00
Scott Lahteine
f7f6b5faae
Fix lcd_move_e compile error (PR#143)
...
Fix a compile error introduced in #98
2015-09-07 09:36:05 -05:00
Scott Lahteine
2b30e8ac99
Conditionals for ULTIPANEL without SDSUPPORT
2015-09-06 02:04:49 -05:00
Scott Lahteine
7c7a4051fe
Disable SDSUPPORT by default
...
As noted in #133 you can’t disable `SDSUPPORT` with `MAKRPANEL`,
`PANEL_ONE`, `MINIPANEL`, or `ULTIPANEL`. This patch makes it possible
to disable `SDSUPPORT` on these controllers and then disables it by
default.
Users of these controllers will now need to enable `SDSUPPORT` in their
configurations as others currently do.
2015-09-06 02:04:49 -05:00
Eric Kuzmenko
b23d765991
Added Extrude From Multiple Extruders from LCD feature
2015-09-05 05:33:18 -05:00
Christian Lefrançois
8347a9d6e4
Fix HOMING_BUMP_DIVISOR for deltas configuration
...
* Re-bump speed divisor should be the same for delta printer.
2015-09-03 09:26:28 -05:00
Scott Lahteine
703df2cb6c
Fix error message for probe region sanity check
2015-09-03 03:27:47 -05:00
Shane Francis
4c8330c15c
Trim Adjustments for Delta Configurations
2015-09-03 01:05:33 -05:00
Scott Lahteine
962120d1d2
Fix spacing in some conditional blocks
2015-08-27 20:59:09 -05:00
Richard Wackerbarth
20b4772155
Create DEBUG_LEVELING_FEATURE
2015-08-27 20:52:08 -05:00
Scott Lahteine
194f98ff95
Debug messages for homing and leveling
2015-08-27 20:52:08 -05:00
Richard Wackerbarth
6292d9e815
Rename ENABLE_AUTO_BED_LEVELING
...
With the introduction of the #if ENABLED(…)
reads better than
2015-08-27 20:52:08 -05:00
Richard Marko
91fd66ffba
add Lulzbot TAZ4 example configuration (PR#104)
2015-08-27 08:36:43 -05:00
Wurstnase
7a275773ee
remove colon in utf_mapper.h (PR#106)
2015-08-27 07:15:23 -05:00
Chris Bruner
6b4b6fa315
update for newest version of U8glib_Arduino
2015-08-26 19:52:59 -05:00
Christian Lefrançois
9897a9147c
Update ABL comments (PR#95)
...
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
2015-08-26 05:51:38 -05:00
Christian Lefrançois
a7822e3ff7
Some renaming of Z_PROBE to Z_MIN_PROBE (PR#91)
...
* Fix a couple of renames omission and macro expansion errors.
2015-08-20 06:04:46 -05:00
Richard Wackerbarth
ad90e851b3
Use a small unsigned integer type
2015-08-16 06:56:47 -05:00
Richard Wackerbarth
29b456ae07
Suppress some compiler warnings
2015-08-16 06:56:47 -05:00
Scott Lahteine
23d742bf06
Don't free the stack array plane_equation_coefficients (PR#83)
2015-08-16 06:53:24 -05:00
Scott Lahteine
e3b1e08777
Patch G30 to use raise_z_for_servo (PR#73)
2015-08-15 21:47:04 -05:00
Scott Lahteine
a1eb90d5c0
Save another 30 bytes in gcode_SET_Z_PROBE_OFFSET
2015-08-12 21:26:32 -05:00
Scott Lahteine
91122277f4
Reduce gcode_SET_Z_PROBE_OFFSET by 88 bytes
2015-08-12 21:26:25 -05:00
AnHardt
5707a2c3d5
indexindexIntoAB is only vald for !DELTA
2015-08-11 17:32:11 -05:00
AnHardt
d8860f9ad9
Alway end at the same point
...
Always end at [RIGHT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION]
Regardles the evennes of auto_bed_leveling_grid_points.
2015-08-11 17:32:11 -05:00
AnHardt
4ca8f4a9a7
Always zigzag
...
Use the shortest way between probing-points.
2015-08-11 17:32:11 -05:00
AnHardt
3d23424121
Add array indexIntoAB[xx][yy]
...
and use it.
2015-08-11 17:32:11 -05:00
AnHardt
e2d69f66b2
Make Z_PROBE a Z_MIN_PROBE (PR#65)
...
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.
Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX check for the probe in update_endstops().
Using an delta related idea of @clefranc from #61 ,
extended to the general change for all setups.
Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
2015-08-11 14:41:36 -05:00
AnHardt
6a6e863a47
Resolve #2581 by adding a missed ';' (PR#67)
2015-08-10 12:51:59 -05:00
RicardoGA
e09ff79635
Update pins_RAMPS_13.h (PR#64)
...
Now all ramps configuration can enable Filament sensor not only EEB
2015-08-10 05:53:01 -05:00
Fourmi
e6aed7bb4e
Update thermistortables for Hisens Thermistor (PR#2588)
2015-08-09 18:11:14 -05:00
Richard Wackerbarth
9d8cc24abf
Continue from the line following the M999 (PR#60)
...
If the printer is going to accept the M999,
then it should continue from that line number.
2015-08-08 08:08:02 -05:00
wurstnase
f3ab1dba54
Z babystepping for coreXY (PR#47)
...
only X and Y were not implemented
2015-08-04 20:10:09 -05:00
Richard Wackerbarth
35afea1c0e
Restore test
...
PR#2572 Changed this because of faulty Boolean Logic
NOT(A OR (NOT B) OR (NOT C)) !=
(NOT A) AND ((NOT B) OR C))
Besides, the compiler should be smart enough to
optimize this without help from the programmer
2015-08-04 15:22:56 -05:00
Scott Lahteine
6af75f4b5d
Squish down deprecated tests in sanity check
2015-08-03 16:04:48 -05:00
Scott Lahteine
edeb58288e
Use PIN_EXISTS in sanity check
2015-08-03 16:04:48 -05:00
Scott Lahteine
c30b7693e0
Clean up RUMBA pins conditions
2015-08-03 16:04:48 -05:00
Scott Lahteine
46453905d6
Apply remaining ENABLED/DISABLED conditionals
2015-08-03 16:04:48 -05:00
Richard Wackerbarth
b227d8c128
Supply a VERSION in a short form for displays
...
The long descriptor will still be available in M115
2015-08-03 08:21:09 -05:00
Richard Wackerbarth
cd7828a928
This will be the 1.1.0 Release rather than 1.0.3
2015-08-03 08:08:38 -05:00
Richard Wackerbarth
4e2f5618c1
Pick up Default_version when needed
2015-08-03 08:08:37 -05:00
Richard Wackerbarth
329acc852e
Canonize Option flag USE_AUTOMATIC_VERSION
2015-08-03 08:08:37 -05:00
Richard Wackerbarth
5a11d32a85
Move deprecation test to SanityCheck.h
2015-08-03 08:08:37 -05:00
Richard Wackerbarth
7bb7a52940
Bring config up-to-date
2015-08-03 07:35:33 -05:00
AnHardt
244ea2014a
Boot-screen for text-displays improvements
...
Centred the logo for 16x4 and 20 x4.
Moved version to the bottom line
Code shrink to 704 bytes.
2015-08-03 07:13:00 -05:00
AnHardt
80f2a20842
Enable bootscreen in all Configurations
2015-08-03 07:13:00 -05:00
AnHardt
2684d061ed
Scroll too long strings on bootscreen
2015-08-03 07:13:00 -05:00
AnHardt
4f46df5dab
Make bootscreen configurable for the graphic displays
...
Saves about 473 byte of progmem and 28 bytes of RAM.
2015-08-03 07:13:00 -05:00
AnHardt
09571b7753
Boot-screen for the character displays
...
Uses about 488 byte of progmem and 32 byte of RAM.
For that configurable.
2015-08-03 07:13:00 -05:00
Richard Wackerbarth
866efc14fe
Add Danish translations
2015-08-03 07:06:17 -05:00
Scott Lahteine
267f3479d7
Adjust spacing in pins_RAMPS_13.h
2015-08-02 23:26:58 -05:00
Scott Lahteine
56702e7bb9
Define servo pins just like other pins
2015-08-02 23:26:58 -05:00
Richard Wackerbarth
4b9d5cd352
Use lowercase names for serial instances
2015-08-02 23:01:39 -05:00
Scott Lahteine
1e2deff4fd
Rename BTENABLED to BLUETOOTH
...
- For some reason it’s easy to forget what BT stands for, but it
doesn’t need an abbreviation.
2015-08-02 22:56:50 -05:00
Scott Lahteine
68055a5959
Include RIGIDBOT_PANEL in Conditionals
2015-08-02 22:26:41 -05:00
George Djabarov
f8ed3a835d
Added comment with the RigidBot Big bed size
2015-08-02 22:13:37 -05:00
George Djabarov
7deae6b6be
Updated RigidBot example configuration
...
- The default serial baud rate of 115200
- The regular RigitBot bed size 254mm/248mm/254mm
- Single stock extruder
- Stock termistors for extruder and hotbed
- Stock Min X/Y/Z stops. Max stops not connected
- Stock 32 teth tooleys (stock axis steps)
- No auto bed leveling
- No screen
2015-08-02 22:13:37 -05:00
Scott Lahteine
5418faa1f9
Add sanity checks for old names
2015-08-02 22:09:08 -05:00
Scott Lahteine
f03e063750
Rename BEEPER to BEEPER_PIN
...
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
2015-08-02 22:09:08 -05:00
Scott Lahteine
270c766de2
SDCARDDETECT -> SD_DETECT, added docs
...
- `SD_DETECT_PIN` replaces `SDCARDDETECT`
- `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED`
- Revise the description of `SD_DETECT_INVERTED`
- Add a note about the override of `SD_DETECT_INVERTED` in
`Conditionals.h`
2015-08-02 21:59:41 -05:00
Scott Lahteine
496fc28dc3
Tweaks to pins comments
2015-08-02 21:34:13 -05:00
Scott Lahteine
8d3b74cc6e
Rename SDCARDDETECT to SDCARDDETECT_PIN
...
- Rename the pin so it can be tested with `PIN_EXISTS`
- Fix some incorrect tests for `SDCARDDETECT`
2015-08-02 21:34:13 -05:00
Scott Lahteine
0f5ada8cbd
Group the fail case in one negation (PR#2572)
2015-08-01 18:55:50 -05:00
AnHardt
7ddf1cda1d
Improve condition for SERVO_LEVELING (PR#2570)
2015-07-31 22:41:34 -05:00
Richard Wackerbarth
f32048b8f5
In for a penny, in for a pound
2015-07-31 17:13:53 -05:00
Scott Lahteine
e944f960de
Add a sanity check for old name "BEEPER"
2015-07-31 17:13:53 -05:00
Scott Lahteine
8ebf0b92be
Spacing adjustments in some pins files
2015-07-31 17:13:53 -05:00
Scott Lahteine
94a796c8cc
Rename BEEPER to BEEPER_PIN
...
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
2015-07-31 17:13:53 -05:00
Richard Wackerbarth
b217474eab
Compiler Complaints about concatenated tokens (PR#2566)
2015-07-31 17:08:44 -05:00
Scott Lahteine
2460f82d8b
Make proper distinction between BEEPER and HAS_BUZZER
2015-07-31 01:24:33 -05:00
Scott Lahteine
58cfcd4239
Overridable Options - Part 5
...
Apply `ENABLED` / `DISABLED` macros to files needing only a small
number of changes.
2015-07-31 01:24:20 -05:00
Scott Lahteine
5e834352a9
Overridable Options - Part 11 (PR#2563)
...
Apply `ENABLED` / `DISABLED` macros to EEPROM-related files.
2015-07-31 01:07:04 -05:00
Scott Lahteine
bf6eb93c61
Overridable Options - Part 10 (PR#2562)
...
Apply `ENABLED` / `DISABLED` macros to planner files.
2015-07-31 01:06:29 -05:00
Scott Lahteine
51e89a269c
Overridable Options - Part 9 (PR#2561)
...
Apply `ENABLED` / `DISABLED` macros to temperature-related files.
2015-07-31 01:05:55 -05:00
Scott Lahteine
c35fb88094
Overridable Options - Part 8 (PR#2560)
...
Apply `ENABLED` / `DISABLED` macros to stepper-related files.
2015-07-31 01:05:22 -05:00
Scott Lahteine
0d8989fc14
Overridable Options - Part 7 (PR#2559)
...
Apply `ENABLED` / `DISABLED` macros to LCD-related files.
2015-07-31 01:04:37 -05:00
Scott Lahteine
b4abb0ae7f
Apply ENABLED / DISABLED to Marlin core files (PR#2558)
2015-07-31 01:03:58 -05:00
Scott Lahteine
c0d7ea3e7e
Overridable Options - Part 4 (PR#2556)
...
Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files.
2015-07-31 00:44:53 -05:00
Scott Lahteine
4b40964064
Overridable Options - Part 3 (PR#2555)
...
Apply `ENABLED` / `DISABLED` macros to language-related files.
2015-07-31 00:19:13 -05:00
Scott Lahteine
32683b282b
Include configurator copies of configs
2015-07-31 00:03:36 -05:00
Scott Lahteine
37d1879386
Apply overridables to Configuration files
2015-07-31 00:03:36 -05:00
Scott Lahteine
9d151bb61b
servo_endstop_angles -> servo_endstop_angle
2015-07-30 23:35:57 -05:00
Scott Lahteine
9334479aeb
Minor cleanup of Conditionals.h
2015-07-30 23:35:57 -05:00
Scott Lahteine
1f63293624
servo_endstops -> servo_endstop_id
2015-07-30 23:35:57 -05:00
Scott Lahteine
edaaead7e0
Fix comment about SERVO_ENDSTOP_ANGLES
2015-07-30 23:35:57 -05:00
Scott Lahteine
ed4a6371ad
Add HAS_SERVO_ENDSTOPS to simplify conditonals
2015-07-30 23:35:57 -05:00
Scott Lahteine
70be61d416
Reset filament_size with a loop
2015-07-30 23:31:58 -05:00
Scott Lahteine
ae9274be05
Fix minor compiler warnings in for loops
2015-07-30 23:31:58 -05:00
Scott Lahteine
c7c8cfed6f
Complete M200 output with M503
...
- The contents of EEPROM include filament diameters even with
Volumetric disabled. This change makes `M503` display the full
volumetric settings so that playing back the output of `M503 S0` will
fully restore them.
2015-07-30 23:31:58 -05:00
Scott Lahteine
4a58e447a1
Add array size to servo_endstop_angles (PR#2553)
2015-07-30 23:27:38 -05:00
Andrew Lenharth
a0ae9e30df
don't pass integer by reference, inefficient. (PR#2547)
2015-07-30 17:51:12 -05:00
AnHardt
d03f037a92
Get rid of malloc() and free() (PR#2549)
...
Just the minimal changes to qr_solve.cpp and .h to get rid of malloc() and free().
Saves about 656 bytes of progmem (library-code)
and 22 bytes for static variables.
Should use exactly the same amount of stack as it did before on the heap.
2015-07-30 17:50:31 -05:00
Scott Lahteine
3b2b2313ff
Combine if block related to SERVO_ENDSTOPS
2015-07-30 16:39:05 -05:00
Scott Lahteine
0af2a80e06
Make SERVO_ENDSTOP_ANGLES 2-dimensional
2015-07-30 16:38:56 -05:00
Richard Wackerbarth
525d0dc239
Configurator is out-of-date AGAIN (PR#2550)
2015-07-30 16:36:01 -05:00
Richard Marko
dd22cbbfb8
makefile: add buzzer.cpp (PR#2479)
2015-07-30 07:56:44 -05:00
Scott Lahteine
9f48798ffd
Replace ENABLED with DEFINED for SERVO_ENDSTOPS (PR#2542)
2015-07-30 07:55:29 -05:00
Richard Wackerbarth
ae00fad75b
Rename as M100
2015-07-27 20:31:59 -05:00
Richard Wackerbarth
a401d738df
There is an echo in here
2015-07-27 20:31:59 -05:00
Richard Wackerbarth
ed7d45e8f5
Memory watcher
2015-07-27 20:31:59 -05:00
AnHardt
d17f7ebc8a
Multiply WATCH_TEMP_PERIOD by 1000UL (PR#2535)
...
instead of 1000. Else we get errors with times over 32 seconds.
2015-07-27 20:30:53 -05:00
Scott Lahteine
bea6739774
Don't include Z_RAISE_AFTER_PROBING if not used (PR#2527)
2015-07-27 20:24:33 -05:00
Scott Lahteine
81bba7ed88
More sanity checking for extruder requirements (PR#2531)
2015-07-27 10:14:43 -05:00
AnHardt
87a97f3724
Fix conditions for display strings
2015-07-26 20:41:21 -05:00
AnHardt
aaccea0260
Shift some display only strings from language.h to lenguage_en.h
...
and translate them to German.
2015-07-26 20:41:15 -05:00
Scott Lahteine
e4c01f1c7e
Simplify init with ARRAY_BY_EXTRUDERS1 macro (PR#2507)
2015-07-26 20:40:27 -05:00
Scott Lahteine
ab6f1fdf8b
Move & document ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED (PR#2528)
...
As suggested in #2521
- Move `ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED` because `SDSUPPORT` is
also required.
- Add a note that endstops must be enabled for the feature to have any
effect
2015-07-26 20:36:37 -05:00
Richard Marko
1183c10a2e
makefile: drop -q -q (much quiet) from avrdude flags
...
Annoying when trying to figure out if uploading
actually does something.
2015-07-26 20:31:31 -05:00
Richard Marko
0e064357f4
makefile: use /etc/avrdude/avrdude.conf on linux
...
No need to look for arduino specific avrdude configuration
as distributions ship their own avrdude.conf file that
is compatible with arduino.
2015-07-26 20:31:31 -05:00
Scott Lahteine
bcb7d5a149
Improve sanitycheck for TEMP_SENSOR_1
2015-07-25 21:17:36 -05:00
Scott Lahteine
5b24f59401
Add sanity checks for temp sensors
2015-07-25 21:17:36 -05:00
AnHardt
fd0e81b0c7
Distinguish between BUZZER and SPEAKER (PR#2513)
...
A speaker needs a AC or a pulsed DC to make a sound, a buzzer only needs a DC.
A buzzer has it's own resonator. It works in most cases to feed the buzzer with a pulsed DC, but the sound will not be as loud as with pure DC.
There seem to be boards where the BEEPER-pin is not able to handle a PWM. Obviously intended for a buzzer.
To make these board able to handle a speaker
* replace the PWM based tone()-function again with a on-delay-off-delay loop.
Hopefully the last time I touch the beeper code.
2015-07-24 22:10:04 -05:00
Scott Lahteine
e2957df05c
Shorthand for do_blocking_move_to
2015-07-24 22:07:41 -05:00
Scott Lahteine
819c5b9b50
Adjust comment on Z adjustment
2015-07-24 22:07:41 -05:00
Scott Lahteine
5a7356b6fc
Patch for G29 final Z position
...
Include all the necessary pieces to get the final Z position after
probing the bed, and add commentary about other possible changes.
2015-07-24 22:07:41 -05:00
AnHardt
088e09e052
Add forgotten Marlin_main.cpp
2015-07-24 22:04:49 -05:00
AnHardt
8b876241bd
Some more servo code tweaks
...
Just set up the pin. Don't move to a random position.
Simplify servo::move()
* servo::move() does not need the pin parameter - The pin is set during servo_init() with attach().
* servo::move() does not need a return value.
SERVO_LEVELING is the wrong condition to deactivate the servos.
Remove some temporary (Servo *) variables.
SanityCheck for the servo indexes.
2015-07-24 22:04:49 -05:00
Scott Lahteine
b116c096bd
Reduce set_homing_bump_feedrate, save 42 bytes (PR#2512)
...
Updates to `set_homing_bump_feedrate`:
- Move the string into Program Memory, reduce length by 31 bytes
- Use an auto to get the divisor, adjust it on error
- Set feedrate once, at the end
2015-07-24 22:00:25 -05:00
Scott Lahteine
f7e7862588
Better Sanguinololu & Graphical Controller (PR#2504)
...
- Change suggested at
https://github.com/MarlinFirmware/Marlin/issues/2482#issuecomment-123553
266
2015-07-23 23:47:07 -05:00
Scott Lahteine
a1154d4a20
Enable Y and sanity-check CoreXZ (PR#2509)
2015-07-23 23:46:27 -05:00
Scott Lahteine
932f1c109e
Move servos to the top in pins_MEGACONTROLLER.h
2015-07-23 22:51:41 -05:00
Scott Lahteine
90f8ddfc1e
Apply MINIPANEL to other configs
2015-07-23 22:51:41 -05:00
AndySze
00dbf69b6d
add MINIPANEL defines
2015-07-23 22:51:40 -05:00
AndySze
8ac5e56934
fixed some format problems and cleaned code
2015-07-23 22:51:40 -05:00
AndySze
eef595aa64
add makerlab mega controller pin configs
2015-07-23 22:51:40 -05:00
AnHardt
4e14e152fa
Add Travis tests for CORXY and COREXZ
2015-07-23 19:52:48 -05:00
AnHardt
27d7d2ccab
Correct bracketing for COREXY-XZ
2015-07-23 19:52:21 -05:00
Scott Lahteine
469843427d
Reduce code in gcode_M81 (PR#2497)
2015-07-23 08:14:00 -05:00
Scott Lahteine
c66955aaf9
Mark unchanging arrays as const (PR#2494)
...
The compiler may be able to optimize if it knows an array won’t be
changing.
2015-07-22 21:37:37 -05:00
Scott Lahteine
278aa15301
Add COUNT macro and apply
2015-07-22 18:16:05 -05:00
Scott Lahteine
d85861d296
Move macros, add ENABLED/DISABLED, add includes
2015-07-22 18:16:05 -05:00
Scott Lahteine
17960fd2b0
Neaten up pins_MEGATRONICS.h (PR#2493)
2015-07-22 17:23:22 -05:00
Scott Lahteine
aac2b9aa9d
Reduce code in gcode_M84 (PR#2492)
...
`gcode_M84` only needs to call `finishAndDisableSteppers`, which calls
all the other functions.
2015-07-22 17:22:01 -05:00
Scott Lahteine
4971fa73f9
Add a sanitycheck error for old servo settings (PR#2491)
...
- Documentation solution for #2476
2015-07-22 16:35:10 -05:00
Scott Lahteine
96ace72ddc
Servos attach/detach based only on servo config
...
Assuming #2470 fixed up the main issue.
2015-07-22 16:34:26 -05:00
Richard Wackerbarth
b80a6a8d31
Correct Kossel Pro Configuration_adv (PR#2473)
2015-07-22 16:32:08 -05:00
Scott Lahteine
000a6fce46
Extract update_endstops from stepper ISR (PR#2474)
2015-07-19 18:33:18 -05:00
Scott Lahteine
e83eac312e
Move plan_arc next to prepare_move
2015-07-19 16:18:46 -05:00
Scott Lahteine
5c5936508d
G2/G3 Arcs for Delta
...
- Update prepare_move_delta to take a target argument
- Add Delta support to plan_arc
2015-07-19 16:18:46 -05:00
Scott Lahteine
9f53e2f0c9
Implement COREXZ in stepper.cpp and planner.cpp
2015-07-19 16:17:03 -05:00
Scott Lahteine
fa00e1d97f
Explode conditions common to corexy and cartesian
2015-07-19 16:17:03 -05:00
Scott Lahteine
c7dd5527b4
Add a C_AXIS and Z_HEAD to support COREXZ
2015-07-19 16:17:03 -05:00
Scott Lahteine
129f986ccf
Add COREXZ option to configurations
2015-07-19 16:17:03 -05:00
Scott Lahteine
69b0490b77
Show minimal preheat options in menus (PR#2471)
2015-07-19 16:14:59 -05:00
Scott Lahteine
eacfe132aa
Change the name of servos[] and servo_t
2015-07-19 11:35:48 -07:00
Scott Lahteine
3b23ccd366
Patch servos code for move
...
- Have `Servo::attach` explicitly return -1 if it fails
- Check for -1 in `Servo::move` because `servoIndex` might be 0
- Make `attach` / `detach` calls conditional on `SERVO_LEVELING`
- Move `SERVO_LEVELING` define to `Conditionals.h`
2015-07-19 11:24:23 -07:00
Richard Wackerbarth
54ddc1d417
Simplify DRY RUN (PR#2358)
...
Elsewhere DRYRUN turns off the heating elements
and ignores constraints on them.
Here, whenever motion is entered into the planner,
if DRY RUN is set, we instantly act as if the E_AXIS
is in the desired final position.
2015-07-19 10:15:53 -05:00
Scott Lahteine
944090c19c
Optimize lsDive logic
2015-07-19 10:13:40 -05:00
Scott Lahteine
417706e578
Include space for the terminating nul in lsDive
2015-07-19 10:13:39 -05:00
Scott Lahteine
f3c1a6b19c
Reduce lsDive stack usage to the minimum
2015-07-19 10:13:39 -05:00
Patrick Bogen
fba4e6241b
Specify print format for reporting invalid tmp_extruder (PR#2465)
2015-07-18 16:40:01 -05:00
AnHardt
d15d869267
Rename axis_is_at_home() to set_axis_is_at_home() (PR#2464)
...
to make clear - it's not a question but an order.
2015-07-18 10:27:21 -05:00
Scott Lahteine
f209b755a5
Move the Z probe as far as needed to trigger the switch (PR#2461)
2015-07-16 20:02:44 -05:00
Scott Lahteine
0f1df62389
Fixup comments in code_seen
2015-07-16 16:40:52 -05:00
Scott Lahteine
2945eb6650
Call code_seen only once per parameter
2015-07-16 16:40:52 -05:00
Scott Lahteine
b742af2e2a
Move Y_STOP_PIN for Printrboard with SD (PR#2420)
2015-07-16 16:39:55 -05:00
Scott Lahteine
baa9199973
Define extern delta only for delta
2015-07-16 16:36:30 -05:00
Scott Lahteine
77e80ef367
Require extruders for thermal code
2015-07-16 16:36:30 -05:00
Scott Lahteine
3bde4f4855
Require temp sensor for bed thermal protection
2015-07-16 16:36:30 -05:00
Scott Lahteine
82a3ed2f9a
Cleanup and dev notes in Marlin.h
2015-07-16 16:36:30 -05:00
Scott Lahteine
db23b9b184
Minor tweak to M204 code (PR#2457)
2015-07-16 16:35:13 -05:00
Scott Lahteine
81d42406b7
Move braces in homeaxis to prevent a hanging else (PR#2451)
2015-07-16 10:25:54 -05:00
Scott Lahteine
552a327df8
Fix lsDive filename stack overrun (PR#2449)
2015-07-16 10:23:56 -05:00
AnHardt
a6628f12cc
Eliminate the further use of the pin-parameter
2015-07-15 20:50:58 -05:00
AnHardt
8504992e9f
Remove the additional pin variable in Servo.cpp
...
as sugested by @c-born
inhttps://github.com/MarlinFirmware/Marlin/issues/1885#issuecomment-92618240
2015-07-15 20:50:58 -05:00
AnHardt
ed6598adf5
Corrected Bed Height vs. Bed Topology for verbosity > 3
...
and cleaned out some tabs.
Everything else is a rebased PR#2017 as proposed by @CptanPanic
2015-07-15 19:51:40 -05:00
brian
62302ceb9e
Add calculation of difference between auto-correct bed level plane, and measured topo map.
2015-07-15 19:51:40 -05:00
Scott Lahteine
de25a48dec
Remove PID examples from preconfigured configs
2015-07-15 19:13:53 -05:00
Scott Lahteine
7456710a1f
Update configs formatting
2015-07-15 19:13:47 -05:00
Scott Lahteine
391386dd94
Update configs for new servo deactivation
2015-07-15 19:13:40 -05:00
AnHardt
5243d8b523
Deactivate DEACTIVATE_SERVOS_AFTER_MOVE by default
2015-07-15 17:39:43 -05:00
AnHardt
49609f6c14
Activate the new servo.move() function
...
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
2015-07-15 17:39:43 -05:00
AnHardt
40b6edcad7
Introduce DEACTIVATE_SERVOS_AFTER_MOVE in Configuration.h
...
DEACTIVATE_SERVOS_AFTER_MOVE is ought to replace PROBE_SERVO_DEACTIVATION_DELAY.
But it will work on all servo moves, not only the probe servo moves.
2015-07-15 17:39:43 -05:00
AnHardt
2ddb2a2be9
Add Servo::move() to servo.cpp
...
move(pin, angel) - Sequence of attach(pin), write(angel),
if DEACTIVATE_SERVOS_AFTER_MOVE is defined waits SERVO_DEACTIVATION_DELAY, than detaches.
As we have jitter on the servos during moves of the steppers, and detaching them improves this behaviour,
the usual sequence to handle a servo movement is:
attach(pin)
write(angel)
delay(until the servo finished the move)
detache()
Here a function to handle the complete sequence.
2015-07-15 17:39:43 -05:00
mkile
8a01e5fb7a
Update Russian translation (PR#2443)
...
Slightly updated translation.
2015-07-15 10:35:36 -05:00
Richard Wackerbarth
e83575537a
Compiler defines USBCON for USB devices (PR#2433)
2015-07-15 10:32:11 -05:00
ayberkozgur
7268d46508
Always calculate extruder temperature PID d term (PR#2432)
2015-07-13 13:22:26 -05:00
Scott Lahteine
87a872e103
Use st_get_position_mm where possible (PR#2411)
2015-07-12 22:15:54 -05:00
Scott Lahteine
2e0da8abdc
Allow N to take a negative argument (PR@2402)
2015-07-12 22:14:25 -05:00
Scott Lahteine
447dbd6fa5
Add STEPPER_RESET_PIN support
2015-07-11 16:04:11 -05:00
Scott Lahteine
a0351bdb73
Remove STEPPER_RESET_FIX option
2015-07-11 16:04:11 -05:00
Scott Lahteine
6b1b8cb2b3
Also nullify spaces before the checksum asterisk (PR#2409)
2015-07-10 09:03:07 -05:00
Scott Lahteine
8e61314323
Use RIGIDBOT_PANEL for consistency with online docs
2015-07-09 11:36:46 -05:00
Scott Lahteine
4b204da3c1
Cleanup of pins_RAMPS_13.h
2015-07-09 11:36:46 -05:00
Scott Lahteine
536f86e896
RigidBot CONTROLLERFAN_PIN in Configuration_adv.h
2015-07-09 11:36:46 -05:00
Scott Lahteine
f068e46661
RigidBoard include for pins.h
2015-07-09 11:36:46 -05:00
Scott Lahteine
9ebcae496d
RIGIDBOARD / RIGIDPANEL
2015-07-09 11:36:46 -05:00
Scott Lahteine
c3c605c658
Move note about LiquidTWI2 to Configuration.h (PR#2406)
2015-07-09 05:33:17 -05:00
Scott Lahteine
4e9d658141
Prevent a hanging SERIAL_ECHO_START in M111
2015-07-07 06:59:10 -05:00
Scott Lahteine
bc0fdbe88e
Use SERIAL_EOL in SERIAL_PROTOCOLLN macros
2015-07-07 06:59:10 -05:00
Scott Lahteine
d78ebbc0e9
Remove unused MSG_OK_B and MSG_OK_T
2015-07-07 06:59:10 -05:00
Scott Lahteine
6b494c1535
Use disable_all_heaters in M111
2015-07-07 06:59:10 -05:00
Scott Lahteine
15190d40df
Add extra EOL after M111
2015-07-07 06:59:10 -05:00
AnHardt
0e1cf78f5c
Remove code for testing if probing range is too small (PR#2390)
...
becaue it is over-restrictive and superseeded by the now working tests
if the probe-recktangle can be reached. See iss#2366
2015-07-07 06:58:01 -05:00
AnHardt
d421f5250d
Correct the sign of zprobe_zoffset for G29 (PR#@391)
...
Sign flipped with #2167 .
See also comments
https://github.com/MarlinFirmware/Marlin/issues/2040#issuecomment-118568355
and following.
2015-07-07 06:55:33 -05:00
Scott Lahteine
52fcc743ab
Replace "target" with "destination" in M600 (PR#2374)
...
- Also fix a bug in `M600` where `Z_MAX_ENDSTOP_INVERTING` is being
used as the index into the `destination[AxisEnum]` array.
2015-07-04 05:55:25 -05:00
Scott Lahteine
a5033c3652
Enable LCD_PIN_RESET if it exists (PR#2375)
2015-07-04 05:53:22 -05:00
AnHardt
23c8c5348f
Z-height fix V2b (PR#2351)
...
here the other two occurences of `Z_PROBE_OFFSET_FROM_EXTRUDER` are
replaced with `zprobe_zoffset`.
2015-07-02 20:30:40 -05:00
Todd Swindoll
a111fbbd0a
z-probe offset fix (PR#2361)
...
verified via 1.0.2 tag that compiles by multiple people,
credit for the fix goes to paulusjacobus for the initial find and
sniffle for the correction so M851 works.
2015-07-02 20:28:07 -05:00
Scott Lahteine
42465ee444
Cleanup of comments & spacing
2015-06-28 08:20:28 -05:00
Scott Lahteine
9682ed455e
Fix comment on M83, add comment to prepare_move
2015-06-28 08:20:19 -05:00
Scott Lahteine
bb44fe17cf
Fix typo in buzzer.h endif (PR#2337)
2015-06-27 06:10:19 -05:00
AnHardt
36746143a1
Correct output of M48 (PR#2336)
...
n_samples is an uint8_t .
Got printouts like:
50 of 2 ...
2015-06-27 06:08:40 -05:00
Scott Lahteine
f6ca5a8da8
Allow "M110 N123" without a checksum
2015-06-26 18:13:54 -05:00
Scott Lahteine
aaad65ff5d
Include a comment documenting M110
2015-06-26 18:13:54 -05:00
Scott Lahteine
862c72b030
Put the mandatory test of gcode_N first
2015-06-26 18:13:54 -05:00
Scott Lahteine
30976f9773
Allow M110 to handle a second N argument
2015-06-26 18:13:53 -05:00
Scott Lahteine
d135b15bb8
Init all endstop bits to 0 (PR#2332)
2015-06-26 07:10:22 -05:00
Scott Lahteine
5ccb1c9e7d
Use millis for M600 audio feedback interval
2015-06-25 20:45:03 -05:00
Scott Lahteine
fb16a83b8a
Cleanup M600 documentation comments
2015-06-25 20:45:03 -05:00
Scott Lahteine
97ec224d72
Replace target with destination in M600
2015-06-25 20:45:03 -05:00
Scott Lahteine
4ce9ddbb74
Check the temperature before filament change
2015-06-25 20:45:03 -05:00
Jaime van Kessel
b8b5762e55
Update Ultimaker URL
2015-06-25 09:12:44 -05:00
Jaime van Kessel
d5bfbf5a59
Added correct dutch translation for calibrate.
2015-06-25 09:12:44 -05:00
Scott Lahteine
149c474e55
Updated Russian language (PR#2325)
...
Gleaned from
https://github.com/MarlinFirmware/Marlin/commit/4ac14a7e5fa8e6e395436664
8976eafd1ae220ae
2015-06-22 23:07:19 -04:00
AnHardt
722829b058
Move buzzing code to buzzr.h & buzzer.cpp (PR#2307)
...
at least the lcd independent part from Marlin_main.cpp.
2015-06-22 22:31:48 -04:00
AnHardt
c461975140
Rename and repair MELZI_1284 (PR#2301)
...
to MELZI_MAKR3D.
Fix for #2288
As the normal MELZI also can have a 1284.
2015-06-22 22:30:07 -04:00
schlotzz
1e9cf905c7
Enable ZigZag AutoBedLeveling on Deltas (PR#2273)
...
ZigZag has been disabled by fault due to do_topography_map
2015-06-15 20:26:25 -05:00
Scott Lahteine
ec93383ec8
Add SanityCheck for bed probe position settings (PR#2282)
2015-06-15 20:22:44 -05:00
Scott Lahteine
dc40a5f6e0
Patch up more outdated config lines
2015-06-15 20:20:32 -05:00
Scott Lahteine
98c9111a7d
Update delta configs with latest settings
2015-06-15 20:20:32 -05:00
Scott Lahteine
e6baf8afd9
Fix up allen key settings in delta configs
2015-06-15 20:20:31 -05:00
Scott Lahteine
3b293fc5d1
Move Delta settings lower in delta files
2015-06-15 20:20:31 -05:00
Scott Lahteine
df21857583
Move extruder offset settings next to extruders setting
2015-06-15 20:20:31 -05:00
Scott Lahteine
2dd1859247
Cleanup spaces and comments in configs and conditionals
2015-06-15 20:20:31 -05:00
Scott Lahteine
a274769f4f
Clean up spacing and comments
...
Also clean up some trailing spaces in a few other sources
2015-06-15 20:20:31 -05:00
Scott Lahteine
d3bce05d54
Fix up spacing for filament sensor values
2015-06-15 20:20:31 -05:00
Scott Lahteine
b4b10a57fe
Fix configurator section directives and values lists
2015-06-15 20:20:31 -05:00
Scott Lahteine
bba14dcbe6
Move Z Safe Homing point to the middle of the movement range
2015-06-15 20:20:31 -05:00
Scott Lahteine
318318b02f
Add pins_RAMPS_13_EFB.h to reduce redundancy
2015-06-15 20:17:09 -05:00
Scott Lahteine
346c8b339b
Remove a test from pins_RAMPS_13.h
...
- Add 3 new lines to `pins.h` to remove 2 redundant tests in
`pins_RAMPS_13.h`
2015-06-15 20:15:38 -05:00
AnHardt
b93cddfcc9
Add lost MKS_BASE to pins.h (PR#2297)
2015-06-15 10:23:46 -05:00
AnHardt
6ab7b560af
Rework buzzing (PR#2296)
...
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.
Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.
All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.
To do: Check the conditions for the BEEPER-pin in all pin-files.
2015-06-15 06:13:26 -05:00
Scott Lahteine
29122db2fa
Fix ULTRA_LCD spelling in HAS_LCD_BUZZ
2015-06-15 06:12:34 -05:00
Scott Lahteine
1d94d098bf
Formatting tweaks as part of fixing issue 1497
2015-06-14 19:57:27 -05:00
Scott Lahteine
e602c28ad9
Set auto fan pins to OUTPUT during init
...
Fixes the problem of these pins being left in INPUT state, as described
in #1497
2015-06-14 19:57:27 -05:00
Scott Lahteine
90f858aa85
Use translated strings for axis movement (PR#2280)
...
Suggest we use the translated strings here. They use (except for
German) the phrasing “Move X” instead of just the axis letter, but they
should fit the available space. The “Extruder” string would be the
same, except it will be translated.
2015-06-14 08:16:00 -05:00
Scott Lahteine
e2a4a83586
Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281 )
2015-06-12 22:39:35 -05:00
Scott Lahteine
6b1b3adaf0
Consistent punctuation in SanityCheck errors (PR#2283)
2015-06-12 09:31:02 -05:00
MagoKimbra
eb81982fcd
Fix error next command in autotune (PR#2274)
...
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
2015-06-12 07:10:38 -05:00
AnHardt
55b23c896a
Optimise out_of_range_error() (PR#2265)
...
by avoiding the strncopy()
2015-06-12 02:20:40 -05:00
filipmu
b0860adab6
Fix volumetric multiplier display for filament sensor (PR#2264)
...
The volumetric multiplier display needs to be multiplied by 100 in order to make it an integer for display purposes.
2015-06-12 02:19:27 -05:00
AnHardt
45642b7fe8
Respect DISABLE_AXIS settings (PR#2216)
...
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
2015-06-11 11:35:05 -05:00
wurstnase
c85a486445
make the dual z-endstop optional (PR#2277)
...
it's disabled by default
2015-06-10 15:45:59 -05:00
Scott Lahteine
962b107341
Prevent current_command_args from bypassing nul (PR#2270)
2015-06-09 16:07:10 -05:00
Richard Wackerbarth
06ae832276
Deprecate Support for Arduino IDE < 1.0.5
...
Note that newer versions of the IDE can still
be made to support compilation for the older boards.
2015-06-08 17:15:28 -05:00
Scott Lahteine
ff6081be3a
Parse N[0-9]+[ ]* differently (PR #2263 )
...
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
2015-06-08 17:06:49 -05:00
Scott Lahteine
aad121864e
Include "Z" in M851 report
2015-06-08 05:09:27 -05:00
Scott Lahteine
96a3fba8ac
Reverse the sign of zprobe_zoffset
...
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
2015-06-08 05:09:27 -05:00
fmalpartida
f92907183c
Updated SAV MkI pin header.
2015-06-08 05:07:11 -05:00
Richard Wackerbarth
58941e543e
ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED removed
...
#defining something just to define something else doesn’t
make sense
If you want SDCARDDETECTINVERTED, just define it yourself.
If the previous code was intended to define, undefined and then again define the term, that code is improper.
2015-06-06 21:44:59 -05:00
CONSULitAS
788eb6e647
planner.cpp: remove tab
...
planner.cpp: single evil and hidden tab removed ♻️ 😏
2015-06-06 20:13:56 -05:00
CONSULitAS
3a5963c0e7
Configuration_adv.h: Add FAN_MIN_PWM for slow fan stopping issue …
...
* all Configuration_adv.h: Add #define FAN_MIN_PWM for slow fan stopping
issue
* for K8200: uncommented with tested (and working) values
2015-06-06 20:13:56 -05:00
CONSULitAS
e55e65d1e4
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue …
...
@CONSULitAS
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue (V2.1 with
macro and linear scaling)
@thinkyhead thanks for idea on linear scaling
2015-06-06 20:13:56 -05:00
paclema
8d295547be
* Auto filament change on CHANGEFILAMENT feature. Now you can activate this option that extrude filament until you press the button.
2015-06-06 19:45:45 -05:00
atfield90
6d0e91328d
Renamed Board_megatronics_1 to Board_minitronics
2015-06-06 18:59:04 -05:00
atfield90
c4a2e5ac23
Renamed Pins_megatronics_1 to Pins_minitronics
2015-06-06 18:59:04 -05:00
atfield90
2076906aaa
Renamed Pins_megatronics_1 to Pins_minitronics
2015-06-06 18:59:04 -05:00
tonokip
10733a2bb0
added minirambo pin definitions. V2
2015-06-06 18:37:58 -05:00
Richard Wackerbarth
303d47228e
Define Probe Path in new format
2015-06-06 17:48:27 -05:00
Richard Wackerbarth
ad09d6a60f
3 Step Allen Key Probe
2015-06-06 17:48:27 -05:00
Richard Wackerbarth
8359cdf01d
Check compatibility for Teensy-based processor
...
The instruction say to set a #define in fastio.h
However, that value is not included before this test.
2015-06-06 17:24:34 -05:00
Ed Boston
08968c29bb
Adding ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED to Examples
2015-06-06 16:40:32 -05:00
Ed Boston
fed18bcc20
Removed SDSLOW for ELB_FULL_GRAPHIC_CONTROLLER
...
Hardware changes has removed the need for this option.
2015-06-06 16:40:32 -05:00
Ed Boston
b94a0e1501
Added ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED
...
The new define allows the sd card detect to be inverted or not from
Configuration.h
2015-06-06 16:40:31 -05:00
Ed Boston
bc205c76a3
SDCARDDETECTINVERTED problems
...
Fixed an error where SDCARDDETECTINVERTED was being defined/undefined
improperly
2015-06-06 16:40:31 -05:00
AnHardt
e400fce271
Merge pull request #2221 from MagoKimbra/Dryrun
...
Insert Debug DRYRUN Repetier Host compatible
2015-06-03 12:30:48 +02:00
AnHardt
163a9ff58e
Merge pull request #2230 from AnHardt/psm
...
Fix thermal protection state machine target temp. V2
2015-06-03 09:46:53 +02:00
AnHardt
c3fe6e61ae
Merge pull request #2229 from AnHardt/position-out-of-range
...
Fix out_of_range_error()
2015-06-03 09:46:22 +02:00
MagoKimbra
4db8d2def4
Moved MSG_DEBUG in language.h
2015-06-03 08:18:27 +02:00
AnHardt
b7e9ba7591
Back to 1.0.3 dev - for now
2015-06-03 00:47:11 +02:00
AnHardt
d1f4471000
Merge pull request #2146 from Wackerbarth/Versioning
...
Versioning
2015-06-02 18:31:21 +02:00
AnHardt
b1404a0743
fix thermal protection state machine target temp. V2
...
If the target temperature is changed then it would always stay in the reset state.
Thanks to @tonokip.
Replaces #2119
2015-06-02 12:26:21 +02:00
AnHardt
17b0ec84ed
Fix out_of_range_error()
...
For sprintf_P() the first parameter has to be a `char*` not `const char*`.
2015-06-02 11:50:32 +02:00
AnHardt
35af5ef23e
Merge pull request #2225 from Wurstnase/naming
...
consistency name for multiplier
2015-06-02 10:18:22 +02:00
wurstnase
e7e964432b
consistency name for multiplier
...
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
2015-06-01 22:33:22 +02:00
AnHardt
d4c6fc5d0a
Merge pull request #2223 from AnHardt/dualz-semicolon
...
Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.
2015-06-01 20:15:55 +02:00
AnHardt
0d9d21d15f
Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.
2015-06-01 19:51:43 +02:00
MagoKimbra
76306f9073
Insert Debug DRYRUN Repetier Host compatible
2015-06-01 18:34:45 +02:00
MagoKimbra
881146bc22
Fix problem Width Cura
2015-06-01 17:25:32 +02:00