Scott Lahteine
99282a46e9
Make sure ABL (manual) starts close to the bed
2018-04-13 20:19:30 -05:00
Roxy-3D
21f13f9e57
Stow Probe at end of G29 J3
2018-04-13 14:46:47 -05:00
KangDroid
6c535081ec
[2.0.x] Add optional menu item to toggle software endstops ( #10389 )
2018-04-13 00:24:09 -05:00
Scott Lahteine
3c5c6d478a
Prettify process_parsed_command
2018-04-13 00:23:11 -05:00
Scott Lahteine
0535ebc4d2
MESH_BED_LEVELING before PROBE_MANUALLY
2018-04-12 22:45:52 -05:00
Scott Lahteine
bb7064cc30
Tweak MBL move to bed code
2018-04-12 22:43:02 -05:00
Chris Pepper
cc6d41e1d3
Use a macro for HAL header redirection ( #10380 )
2018-04-12 20:25:08 -05:00
Luc Van Daele
12785583d0
[2.0.x] G33 MIN_STEPS_PER_SEGMENT ( #10386 )
2018-04-12 20:22:29 -05:00
Yunhui Fu
c96412a78f
[2.0.x] UTF-8 language translation support ( #10213 )
2018-04-12 20:14:01 -05:00
Scott Lahteine
daa712455b
Make sure MBL starts close to the bed
...
Fix #10390
2018-04-12 19:36:37 -05:00
Scott Lahteine
4c8751727a
Fix M118 parameter handling
...
Fix #10388
2018-04-12 19:10:04 -05:00
Scott Lahteine
3bc179a16f
Compress/update comments ubl_motion
...
…to fit more code on the screen and correct outdated commentary contrasting ABL.
2018-04-12 18:07:19 -05:00
Luc Van Daele
646aa20b43
Overhaul of G33 Delta Calibration ( #8822 )
2018-04-11 21:14:48 -05:00
Luc Van Daele
ac2e0afb62
Low Point for delta calibration ( #10363 )
2018-04-11 18:59:46 -05:00
Eduardo José Tagle
57a899a412
[2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR ( #10373 )
2018-04-11 18:13:42 -05:00
Bob-the-Kuhn
85014cd132
[2.0.x] LPC1768 - automatic selection of upload disk ( #10374 )
2018-04-11 14:41:16 -05:00
Scott Lahteine
8669dba5e6
Merge pull request #10172 from noingwhat/2.0.x-Filament-Change-Acceleration
...
[2.0.x] Filament load/unload add acceleration for Bowden
2018-04-11 00:39:11 -05:00
Scott Lahteine
472ab0cc24
Tweak RAMPS SDSS pins
2018-04-10 16:47:48 -05:00
LichtiMC
b94c8defee
Provide additional information about SMART-RAMPS board ( #10353 )
2018-04-10 04:02:55 -05:00
Scott Lahteine
6f8e228880
Add RESET_PIN to pins_RAMPS_SMART.h
2018-04-10 03:34:20 -05:00
Sean
2d9b0a66fe
Add Filament Change accelerations
2018-04-09 23:57:27 -05:00
Scott Lahteine
71d3523254
Add Filament Change accelerations to example configs
2018-04-09 23:57:23 -05:00
Scott Lahteine
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
2018-04-09 17:23:03 -05:00
Scott Lahteine
82dafbba33
Add Z_PROBE_LOW_POINT to example configs
2018-04-09 01:55:05 -05:00
Roxy-3D
a731a723e8
Better i3-2020 Z_PROBE_OFFSET_FROM_EXTRUDER
2018-04-08 21:26:36 -05:00
Roxy-3D
26cc12eaa4
Resolve corruption of Max7219 Debug LED Matrix
2018-04-08 21:26:36 -05:00
Scott Lahteine
dca69efc11
Update Bed PID comments
2018-04-08 06:44:47 -05:00
Scott Lahteine
56486c5c0e
Apply const to manage_inactivity
2018-04-08 04:00:26 -05:00
Scott Lahteine
a6485456df
Fix LIGHTWEIGHT_UI with UBL
...
See https://github.com/MarlinFirmware/Marlin/issues/10317#issuecomment-379100702
2018-04-08 03:24:22 -05:00
Scott Lahteine
e02fc4f1d6
Better RESTORE_LEVELING_AFTER_G28 sanity-check
...
As suggested by @GMagician
2018-04-08 03:24:15 -05:00
Scott Lahteine
44a697ab04
Set STM32F1 TEMP_TIMER_FREQUENCY to 1K
...
Responding to https://github.com/MarlinFirmware/Marlin/pull/8833#issuecomment-379426803
2018-04-08 01:08:05 -05:00
Scott Lahteine
cec6e19099
Add RepRapPro Huxley configuration
...
Based on #10343 by @indazoo
2018-04-08 00:37:18 -05:00
Scott Lahteine
9ff4e9e1e6
Patch _IS_HW_SPI so defined() works
2018-04-07 23:29:00 -05:00
Scott Lahteine
cea398849e
Tweak to gcode_line_error/return
2018-04-07 21:25:49 -05:00
etagle
a29adde5c0
Implement BEZIER_JERK_CONTROL
...
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
2018-04-07 21:03:28 -05:00
Scott Lahteine
5932df7ea1
Add BEZIER_JERK_CONTROL to example configs
2018-04-07 21:03:22 -05:00
Lenbok
0e8242180d
Chamber temperature monitoring and auto fan control.
...
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
2018-04-06 23:09:06 -05:00
Scott Lahteine
5b3bda1c16
Add Chamber Temp options to example configs
2018-04-06 23:09:06 -05:00
Bob-the-Kuhn
acda4ecb20
Fix DUE Trinamic SW/HW SPI sanity check ( #10336 )
2018-04-06 22:22:30 -05:00
Bob-the-Kuhn
ab715c70d1
TMC SPI sanity-check and pins debugging ( #10324 )
2018-04-06 20:24:54 -05:00
Scott Lahteine
4dc7e64789
Update Slovak language
...
Based on #10313 by @rmoravcik
2018-04-06 20:23:20 -05:00
Scott Lahteine
0dccf9ea6a
Merge pull request #10318 from marcio-ao/pr-einsy-retro-tmc2130
...
[2.0.x] Fix TMC2130 DIAG1 active high, Einsy Retro
2018-04-06 20:18:34 -05:00
Marcio Teixeira
2efc072fdb
Clear progress bar on completion ( #10333 )
...
Fix #10330
2018-04-06 20:13:19 -05:00
GMagician
6ce060cfe0
[2.0.x] Update language_it.h ( #10322 )
...
Updated to #10296
2018-04-06 20:07:46 -05:00
Marcio Teixeira
9356cf648f
Added support for Einsy Retro
...
http://reprap.org/wiki/EinsyRetro
2018-04-06 19:48:46 -05:00
Marcio Teixeira
75037493fa
Default active low for TMC2130 DIAG1 ( #10294 )
...
- Added sanity check to inform users to set the endstop to inverting
when using SENSORLESS_HOMING
2018-04-06 19:48:46 -05:00
Scott Lahteine
e8e60263c8
Scale feedrate (mm/s to deg/s) for SCARA
2018-04-06 19:47:48 -05:00
Scott Lahteine
051303ad42
Russian language updates
...
From #10311 by @anton-piliugin
2018-04-05 00:46:46 -05:00
Sean
2fa0a73c2c
Implement filament change continuous purge
2018-04-04 20:57:51 -05:00
Scott Lahteine
d133ad61f3
Add continuous purge to example configs
2018-04-04 20:56:18 -05:00