/** * Marlin 3D Printer Firmware * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ /** * SanityCheck.h * * Test configuration values for errors at compile-time. */ #ifndef _SANITYCHECK_H_ #define _SANITYCHECK_H_ /** * Require gcc 4.7 or newer (first included with Arduino 1.6.8) for C++11 features. */ #if __cplusplus < 201103L #error "Marlin requires C++11 support (gcc >= 4.7, Arduino IDE >= 1.6.8). Please upgrade your toolchain." #endif /** * We try our best to include sanity checks for all changed configuration * directives because users have a tendency to use outdated config files with * the bleeding-edge source code, but sometimes this is not enough. This check * forces a minimum config file revision. Otherwise Marlin will not build. */ #if !defined(CONFIGURATION_H_VERSION) || CONFIGURATION_H_VERSION < REQUIRED_CONFIGURATION_H_VERSION #error "You are using an old Configuration.h file, update it before building Marlin." #endif #if !defined(CONFIGURATION_ADV_H_VERSION) || CONFIGURATION_ADV_H_VERSION < REQUIRED_CONFIGURATION_ADV_H_VERSION #error "You are using an old Configuration_adv.h file, update it before building Marlin." #endif /** * Warnings for old configurations */ #if !defined(X_BED_SIZE) || !defined(Y_BED_SIZE) #error "X_BED_SIZE and Y_BED_SIZE are now required! Please update your configuration." #elif WATCH_TEMP_PERIOD > 500 #error "WATCH_TEMP_PERIOD now uses seconds instead of milliseconds." #elif DISABLED(THERMAL_PROTECTION_HOTENDS) && (defined(WATCH_TEMP_PERIOD) || defined(THERMAL_PROTECTION_PERIOD)) #error "Thermal Runaway Protection for hotends is now enabled with THERMAL_PROTECTION_HOTENDS." #elif DISABLED(THERMAL_PROTECTION_BED) && defined(THERMAL_PROTECTION_BED_PERIOD) #error "Thermal Runaway Protection for the bed is now enabled with THERMAL_PROTECTION_BED." #elif (CORE_IS_XZ || CORE_IS_YZ) && ENABLED(Z_LATE_ENABLE) #error "Z_LATE_ENABLE can't be used with COREXZ, COREZX, COREYZ, or COREZY." #elif defined(X_HOME_RETRACT_MM) #error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM." #elif defined(SDCARDDETECTINVERTED) #error "SDCARDDETECTINVERTED is now SD_DETECT_INVERTED. Please update your configuration." #elif defined(BTENABLED) #error "BTENABLED is now BLUETOOTH. Please update your configuration." #elif defined(CUSTOM_MENDEL_NAME) #error "CUSTOM_MENDEL_NAME is now CUSTOM_MACHINE_NAME. Please update your configuration." #elif defined(HAS_AUTOMATIC_VERSIONING) #error "HAS_AUTOMATIC_VERSIONING is now USE_AUTOMATIC_VERSIONING. Please update your configuration." #elif defined(SDSLOW) #error "SDSLOW deprecated. Set SPI_SPEED to SPI_HALF_SPEED instead." #elif defined(SDEXTRASLOW) #error "SDEXTRASLOW deprecated. Set SPI_SPEED to SPI_QUARTER_SPEED instead." #elif defined(FILAMENT_SENSOR) #error "FILAMENT_SENSOR is now FILAMENT_WIDTH_SENSOR. Please update your configuration." #elif defined(ENDSTOPPULLUP_FIL_RUNOUT) #error "ENDSTOPPULLUP_FIL_RUNOUT is now FIL_RUNOUT_PULLUP. Please update your configuration." #elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS) #error "DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated. Use individual USE_*_PLUG options instead." #elif defined(LANGUAGE_INCLUDE) #error "LANGUAGE_INCLUDE has been replaced by LCD_LANGUAGE. Please update your configuration." #elif defined(EXTRUDER_OFFSET_X) || defined(EXTRUDER_OFFSET_Y) #error "EXTRUDER_OFFSET_[XY] is deprecated. Use HOTEND_OFFSET_[XY] instead." #elif defined(PID_PARAMS_PER_EXTRUDER) #error "PID_PARAMS_PER_EXTRUDER is deprecated. Use PID_PARAMS_PER_HOTEND instead." #elif defined(EXTRUDER_WATTS) || defined(BED_WATTS) #error "EXTRUDER_WATTS and BED_WATTS are deprecated. Remove them from your configuration." #elif defined(SERVO_ENDSTOP_ANGLES) #error "SERVO_ENDSTOP_ANGLES is deprecated. Use Z_SERVO_ANGLES instead." #elif defined(X_ENDSTOP_SERVO_NR) || defined(Y_ENDSTOP_SERVO_NR) #error "X_ENDSTOP_SERVO_NR and Y_ENDSTOP_SERVO_NR are deprecated and should be removed." #elif defined(Z_ENDSTOP_SERVO_NR) #error "Z_ENDSTOP_SERVO_NR is now Z_PROBE_SERVO_NR. Please update your configuration." #elif defined(DEFAULT_XYJERK) #error "DEFAULT_XYJERK is deprecated. Use DEFAULT_XJERK and DEFAULT_YJERK instead." #elif defined(XY_TRAVEL_SPEED) #error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead." #elif defined(PROBE_SERVO_DEACTIVATION_DELAY) #error "PROBE_SERVO_DEACTIVATION_DELAY is deprecated. Use DEACTIVATE_SERVOS_AFTER_MOVE instead." #elif defined(SERVO_DEACTIVATION_DELAY) #error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead." #elif ENABLED(FILAMENTCHANGEENABLE) #error "FILAMENTCHANGEENABLE is now ADVANCED_PAUSE_FEATURE. Please update your configuration." #elif ENABLED(FILAMENT_CHANGE_FEATURE) #error "FILAMENT_CHANGE_FEATURE is now ADVANCED_PAUSE_FEATURE. Please update your configuration." #elif defined(FILAMENT_CHANGE_X_POS) || defined(FILAMENT_CHANGE_Y_POS) #error "FILAMENT_CHANGE_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration." #elif defined(FILAMENT_CHANGE_Z_ADD) #error "FILAMENT_CHANGE_Z_ADD is now set with NOZZLE_PARK_POINT. Please update your configuration." #elif defined(FILAMENT_CHANGE_XY_FEEDRATE) #error "FILAMENT_CHANGE_XY_FEEDRATE is now NOZZLE_PARK_XY_FEEDRATE. Please update your configuration." #elif defined(FILAMENT_CHANGE_Z_FEEDRATE) #error "FILAMENT_CHANGE_Z_FEEDRATE is now NOZZLE_PARK_Z_FEEDRATE. Please update your configuration." #elif defined(PAUSE_PARK_X_POS) || defined(PAUSE_PARK_Y_POS) #error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration." #elif defined(PAUSE_PARK_Z_ADD) #error "PAUSE_PARK_Z_ADD is now set with NOZZLE_PARK_POINT. Please update your configuration." #elif defined(PAUSE_PARK_XY_FEEDRATE) #error "PAUSE_PARK_XY_FEEDRATE is now NOZZLE_PARK_XY_FEEDRATE. Please update your configuration." #elif defined(PAUSE_PARK_Z_FEEDRATE) #error "PAUSE_PARK_Z_FEEDRATE is now NOZZLE_PARK_Z_FEEDRATE. Please update your configuration." #elif defined(FILAMENT_CHANGE_RETRACT_FEEDRATE) #error "FILAMENT_CHANGE_RETRACT_FEEDRATE is now PAUSE_PARK_RETRACT_FEEDRATE. Please update your configuration." #elif defined(FILAMENT_CHANGE_RETRACT_LENGTH) #error "FILAMENT_CHANGE_RETRACT_LENGTH is now PAUSE_PARK_RETRACT_LENGTH. Please update your configuration." #elif defined(FILAMENT_CHANGE_EXTRUDE_FEEDRATE) #error "FILAMENT_CHANGE_EXTRUDE_FEEDRATE is now ADVANCED_PAUSE_EXTRUDE_FEEDRATE. Please update your configuration." #elif defined(ADVANCED_PAUSE_EXTRUDE_FEEDRATE) #error "ADVANCED_PAUSE_EXTRUDE_FEEDRATE is now ADVANCED_PAUSE_PURGE_FEEDRATE. Please update your configuration." #elif defined(FILAMENT_CHANGE_EXTRUDE_LENGTH) #error "FILAMENT_CHANGE_EXTRUDE_LENGTH is now ADVANCED_PAUSE_PURGE_LENGTH. Please update your configuration." #elif defined(ADVANCED_PAUSE_EXTRUDE_LENGTH) #error "ADVANCED_PAUSE_EXTRUDE_LENGTH is now ADVANCED_PAUSE_PURGE_LENGTH. Please update your configuration." #elif defined(FILAMENT_CHANGE_NOZZLE_TIMEOUT) #error "FILAMENT_CHANGE_NOZZLE_TIMEOUT is now PAUSE_PARK_NOZZLE_TIMEOUT. Please update your configuration." #elif defined(FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS) #error "FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS is now FILAMENT_CHANGE_ALERT_BEEPS. Please update your configuration." #elif ENABLED(FILAMENT_CHANGE_NO_STEPPER_TIMEOUT) #error "FILAMENT_CHANGE_NO_STEPPER_TIMEOUT is now PAUSE_PARK_NO_STEPPER_TIMEOUT. Please update your configuration." #elif defined(PLA_PREHEAT_HOTEND_TEMP) #error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND. Please update your configuration." #elif defined(PLA_PREHEAT_HPB_TEMP) #error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED. Please update your configuration." #elif defined(PLA_PREHEAT_FAN_SPEED) #error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED. Please update your configuration." #elif defined(ABS_PREHEAT_HOTEND_TEMP) #error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND. Please update your configuration." #elif defined(ABS_PREHEAT_HPB_TEMP) #error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED. Please update your configuration." #elif defined(ABS_PREHEAT_FAN_SPEED) #error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED. Please update your configuration." #elif defined(ENDSTOPS_ONLY_FOR_HOMING) #error "ENDSTOPS_ONLY_FOR_HOMING is deprecated. Use (disable) ENDSTOPS_ALWAYS_ON_DEFAULT instead." #elif defined(HOMING_FEEDRATE) #error "HOMING_FEEDRATE is deprecated. Set individual rates with HOMING_FEEDRATE_(XY|Z|E) instead." #elif defined(MANUAL_HOME_POSITIONS) #error "MANUAL_HOME_POSITIONS is deprecated. Set MANUAL_[XYZ]_HOME_POS as-needed instead." #elif defined(PID_ADD_EXTRUSION_RATE) #error "PID_ADD_EXTRUSION_RATE is now PID_EXTRUSION_SCALING and is DISABLED by default. Are you sure you want to use this option? Please update your configuration." #elif defined(Z_RAISE_BEFORE_HOMING) #error "Z_RAISE_BEFORE_HOMING is now Z_HOMING_HEIGHT. Please update your configuration." #elif defined(MIN_Z_HEIGHT_FOR_HOMING) #error "MIN_Z_HEIGHT_FOR_HOMING is now Z_HOMING_HEIGHT. Please update your configuration." #elif defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING) #error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_CLEARANCE_DEPLOY_PROBE and Z_AFTER_PROBING instead." #elif defined(Z_RAISE_PROBE_DEPLOY_STOW) || defined(Z_RAISE_BETWEEN_PROBINGS) #error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration." #elif defined(Z_PROBE_DEPLOY_HEIGHT) || defined(Z_PROBE_TRAVEL_HEIGHT) #error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration." #elif defined(MANUAL_BED_LEVELING) #error "MANUAL_BED_LEVELING is now LCD_BED_LEVELING. Please update your configuration." #elif defined(MESH_HOME_SEARCH_Z) #error "MESH_HOME_SEARCH_Z is now LCD_PROBE_Z_RANGE. Please update your configuration." #elif defined(MANUAL_PROBE_Z_RANGE) #error "MANUAL_PROBE_Z_RANGE is now LCD_PROBE_Z_RANGE. Please update your configuration." #elif !defined(MIN_STEPS_PER_SEGMENT) #error Please replace "const int dropsegments" with "#define MIN_STEPS_PER_SEGMENT" (and increase by 1) in Configuration_adv.h. #elif MIN_STEPS_PER_SEGMENT <= 0 #error "MIN_STEPS_PER_SEGMENT must be at least 1. Please update your Configuration_adv.h." #elif defined(PREVENT_DANGEROUS_EXTRUDE) #error "PREVENT_DANGEROUS_EXTRUDE is now PREVENT_COLD_EXTRUSION. Please update your configuration." #elif defined(SCARA) #error "SCARA is now MORGAN_SCARA. Please update your configuration." #elif defined(ENABLE_AUTO_BED_LEVELING) #error "ENABLE_AUTO_BED_LEVELING is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT." #elif defined(AUTO_BED_LEVELING_FEATURE) #error "AUTO_BED_LEVELING_FEATURE is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT." #elif defined(ABL_GRID_POINTS) #error "ABL_GRID_POINTS is now GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y. Please update your configuration." #elif defined(ABL_GRID_POINTS_X) || defined(ABL_GRID_POINTS_Y) #error "ABL_GRID_POINTS_[XY] is now GRID_MAX_POINTS_[XY]. Please update your configuration." #elif defined(ABL_GRID_MAX_POINTS_X) || defined(ABL_GRID_MAX_POINTS_Y) #error "ABL_GRID_MAX_POINTS_[XY] is now GRID_MAX_POINTS_[XY]. Please update your configuration." #elif defined(MESH_NUM_X_POINTS) || defined(MESH_NUM_Y_POINTS) #error "MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]. Please update your configuration." #elif defined(UBL_MESH_NUM_X_POINTS) || defined(UBL_MESH_NUM_Y_POINTS) #error "UBL_MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]. Please update your configuration." #elif defined(UBL_G26_MESH_VALIDATION) #error "UBL_G26_MESH_VALIDATION is now G26_MESH_VALIDATION. Please update your configuration." #elif defined(UBL_MESH_EDIT_ENABLED) #error "UBL_MESH_EDIT_ENABLED is now G26_MESH_VALIDATION. Please update your configuration." #elif defined(UBL_MESH_EDITING) #error "UBL_MESH_EDITING is now G26_MESH_VALIDATION. Please update your configuration." #elif defined(BLTOUCH_HEATERS_OFF) #error "BLTOUCH_HEATERS_OFF is now PROBING_HEATERS_OFF. Please update your configuration." #elif defined(BEEPER) #error "BEEPER is now BEEPER_PIN. Please update your pins definitions." #elif defined(SDCARDDETECT) #error "SDCARDDETECT is now SD_DETECT_PIN. Please update your pins definitions." #elif defined(STAT_LED_RED) || defined(STAT_LED_BLUE) #error "STAT_LED_RED/STAT_LED_BLUE are now STAT_LED_RED_PIN/STAT_LED_BLUE_PIN. Please update your pins definitions." #elif defined(LCD_PIN_BL) #error "LCD_PIN_BL is now LCD_BACKLIGHT_PIN. Please update your pins definitions." #elif defined(LCD_PIN_RESET) #error "LCD_PIN_RESET is now LCD_RESET_PIN. Please update your pins definitions." #elif defined(EXTRUDER_0_AUTO_FAN_PIN) || defined(EXTRUDER_1_AUTO_FAN_PIN) || defined(EXTRUDER_2_AUTO_FAN_PIN) || defined(EXTRUDER_3_AUTO_FAN_PIN) #error "EXTRUDER_[0123]_AUTO_FAN_PIN is now E[0123]_AUTO_FAN_PIN. Please update your Configuration_adv.h." #elif defined(min_software_endstops) || defined(max_software_endstops) #error "(min|max)_software_endstops are now (MIN|MAX)_SOFTWARE_ENDSTOPS. Please update your configuration." #elif ENABLED(Z_PROBE_SLED) && defined(SLED_PIN) #error "Replace SLED_PIN with SOL1_PIN (applies to both Z_PROBE_SLED and SOLENOID_PROBE)." #elif defined(CONTROLLERFAN_PIN) #error "CONTROLLERFAN_PIN is now CONTROLLER_FAN_PIN, enabled with USE_CONTROLLER_FAN. Please update your Configuration_adv.h." #elif defined(MIN_RETRACT) #error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT. Please update your Configuration_adv.h." #elif defined(ADVANCE) #error "ADVANCE was removed in Marlin 1.1.6. Please use LIN_ADVANCE." #elif defined(LIN_ADVANCE_E_D_RATIO) #error "LIN_ADVANCE (1.5) no longer uses LIN_ADVANCE_E_D_RATIO. Check your configuration." #elif defined(NEOPIXEL_RGBW_LED) #error "NEOPIXEL_RGBW_LED is now NEOPIXEL_LED. Please update your configuration." #elif ENABLED(DELTA) && defined(DELTA_PROBEABLE_RADIUS) #error "Remove DELTA_PROBEABLE_RADIUS and use MIN_PROBE_EDGE to inset the probe area instead." #elif defined(UBL_MESH_INSET) #error "UBL_MESH_INSET is now just MESH_INSET. Please update your configuration." #elif defined(UBL_MESH_MIN_X) || defined(UBL_MESH_MIN_Y) || defined(UBL_MESH_MAX_X) || defined(UBL_MESH_MAX_Y) #error "UBL_MESH_(MIN|MAX)_[XY] is now just MESH_(MIN|MAX)_[XY]. Please update your configuration." #elif defined(ABL_PROBE_PT_1_X) || defined(ABL_PROBE_PT_1_Y) || defined(ABL_PROBE_PT_2_X) || defined(ABL_PROBE_PT_2_Y) || defined(ABL_PROBE_PT_3_X) || defined(ABL_PROBE_PT_3_Y) #error "ABL_PROBE_PT_[123]_[XY] is now PROBE_PT_[123]_[XY]. Please update your configuration." #elif defined(UBL_PROBE_PT_1_X) || defined(UBL_PROBE_PT_1_Y) || defined(UBL_PROBE_PT_2_X) || defined(UBL_PROBE_PT_2_Y) || defined(UBL_PROBE_PT_3_X) || defined(UBL_PROBE_PT_3_Y) #error "UBL_PROBE_PT_[123]_[XY] is now PROBE_PT_[123]_[XY]. Please update your configuration." #elif defined(ENABLE_MESH_EDIT_GFX_OVERLAY) #error "ENABLE_MESH_EDIT_GFX_OVERLAY is now MESH_EDIT_GFX_OVERLAY. Please update your configuration." #elif defined(BABYSTEP_ZPROBE_GFX_REVERSE) #error "BABYSTEP_ZPROBE_GFX_REVERSE is now set by OVERLAY_GFX_REVERSE. Please update your configurations." #elif defined(UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN) #error "UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN is now SEGMENT_LEVELED_MOVES. Please update your configuration." #elif HAS_PID_HEATING && (defined(K1) || !defined(PID_K1)) #error "K1 is now PID_K1. Please update your configuration." #elif defined(PROBE_DOUBLE_TOUCH) #error "PROBE_DOUBLE_TOUCH is now MULTIPLE_PROBING. Please update your configuration." #elif defined(ANET_KEYPAD_LCD) #error "ANET_KEYPAD_LCD is now ZONESTAR_LCD. Please update your configuration." #elif defined(LCD_I2C_SAINSMART_YWROBOT) #error "LCD_I2C_SAINSMART_YWROBOT is now LCD_SAINSMART_I2C_(1602|2004). Please update your configuration." #elif defined(MEASURED_LOWER_LIMIT) || defined(MEASURED_UPPER_LIMIT) #error "MEASURED_(UPPER|LOWER)_LIMIT is now FILWIDTH_ERROR_MARGIN. Please update your configuration." #elif defined(HAVE_TMCDRIVER) #error "HAVE_TMCDRIVER is now HAVE_TMC26X. Please update your Configuration_adv.h." #elif defined(X_IS_TMC) || defined(X2_IS_TMC) || defined(Y_IS_TMC) || defined(Y2_IS_TMC) || defined(Z_IS_TMC) || defined(Z2_IS_TMC) \ || defined(E0_IS_TMC) || defined(E1_IS_TMC) || defined(E2_IS_TMC) || defined(E3_IS_TMC) || defined(E4_IS_TMC) #error "[AXIS]_IS_TMC is now [AXIS]_IS_TMC26X. Please update your Configuration_adv.h." #elif defined(AUTOMATIC_CURRENT_CONTROL) #error "AUTOMATIC_CURRENT_CONTROL is now MONITOR_DRIVER_STATUS. Please update your configuration." #elif defined(FILAMENT_CHANGE_LOAD_LENGTH) #error "FILAMENT_CHANGE_LOAD_LENGTH is now FILAMENT_CHANGE_FAST_LOAD_LENGTH. Please update your configuration." #endif #define BOARD_MKS_13 -47 #define BOARD_TRIGORILLA -343 #if MB(MKS_13) #error "BOARD_MKS_13 has been renamed BOARD_MKS_GEN_13. Please update your configuration." #elif MB(BOARD_TRIGORILLA) #error "BOARD_TRIGORILLA has been renamed BOARD_TRIGORILLA_13. Please update your configuration." #endif /** * Marlin release, version and default string */ #ifndef SHORT_BUILD_VERSION #error "SHORT_BUILD_VERSION must be specified." #elif !defined(DETAILED_BUILD_VERSION) #error "BUILD_VERSION must be specified." #elif !defined(STRING_DISTRIBUTION_DATE) #error "STRING_DISTRIBUTION_DATE must be specified." #elif !defined(PROTOCOL_VERSION) #error "PROTOCOL_VERSION must be specified." #elif !defined(MACHINE_NAME) #error "MACHINE_NAME must be specified." #elif !defined(SOURCE_CODE_URL) #error "SOURCE_CODE_URL must be specified." #elif !defined(DEFAULT_MACHINE_UUID) #error "DEFAULT_MACHINE_UUID must be specified." #elif !defined(WEBSITE_URL) #error "WEBSITE_URL must be specified." #endif /** * Serial */ #if !(defined(__AVR__) && defined(USBCON)) #if ENABLED(SERIAL_XON_XOFF) && RX_BUFFER_SIZE < 1024 #error "SERIAL_XON_XOFF requires RX_BUFFER_SIZE >= 1024 for reliable transfers without drops." #elif RX_BUFFER_SIZE && (RX_BUFFER_SIZE < 2 || !IS_POWER_OF_2(RX_BUFFER_SIZE)) #error "RX_BUFFER_SIZE must be a power of 2 greater than 1." #elif TX_BUFFER_SIZE && (TX_BUFFER_SIZE < 2 || TX_BUFFER_SIZE > 256 || !IS_POWER_OF_2(TX_BUFFER_SIZE)) #error "TX_BUFFER_SIZE must be 0, a power of 2 greater than 1, and no greater than 256." #endif #elif ENABLED(SERIAL_XON_XOFF) || ENABLED(SERIAL_STATS_MAX_RX_QUEUED) || ENABLED(SERIAL_STATS_DROPPED_RX) #error "SERIAL_XON_XOFF and SERIAL_STATS_* features not supported on USB-native AVR devices." #endif #if SERIAL_PORT > 7 #error "Set SERIAL_PORT to the port on your board. Usually this is 0." #endif /** * Dual Stepper Drivers */ #if ENABLED(X_DUAL_STEPPER_DRIVERS) && ENABLED(DUAL_X_CARRIAGE) #error "DUAL_X_CARRIAGE is not compatible with X_DUAL_STEPPER_DRIVERS." #elif ENABLED(X_DUAL_STEPPER_DRIVERS) && (!HAS_X2_ENABLE || !HAS_X2_STEP || !HAS_X2_DIR) #error "X_DUAL_STEPPER_DRIVERS requires X2 pins (and an extra E plug)." #elif ENABLED(Y_DUAL_STEPPER_DRIVERS) && (!HAS_Y2_ENABLE || !HAS_Y2_STEP || !HAS_Y2_DIR) #error "Y_DUAL_STEPPER_DRIVERS requires Y2 pins (and an extra E plug)." #elif ENABLED(Z_DUAL_STEPPER_DRIVERS) && (!HAS_Z2_ENABLE || !HAS_Z2_STEP || !HAS_Z2_DIR) #error "Z_DUAL_STEPPER_DRIVERS requires Z2 pins (and an extra E plug)." #endif /** * Validate that the bed size fits */ static_assert(X_MAX_LENGTH >= X_BED_SIZE && Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds ([XY]_MIN_POS, [XY]_MAX_POS) are too narrow to contain [XY]_BED_SIZE."); /** * Granular software endstops (Marlin >= 1.1.7) */ #if ENABLED(MIN_SOFTWARE_ENDSTOPS) && DISABLED(MIN_SOFTWARE_ENDSTOP_Z) #if IS_KINEMATIC #error "MIN_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MIN_SOFTWARE_ENDSTOP_Z." #elif DISABLED(MIN_SOFTWARE_ENDSTOP_X) && DISABLED(MIN_SOFTWARE_ENDSTOP_Y) #error "MIN_SOFTWARE_ENDSTOPS requires at least one of the MIN_SOFTWARE_ENDSTOP_[XYZ] options." #endif #endif #if ENABLED(MAX_SOFTWARE_ENDSTOPS) && DISABLED(MAX_SOFTWARE_ENDSTOP_Z) #if IS_KINEMATIC #error "MAX_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MAX_SOFTWARE_ENDSTOP_Z." #elif DISABLED(MAX_SOFTWARE_ENDSTOP_X) && DISABLED(MAX_SOFTWARE_ENDSTOP_Y) #error "MAX_SOFTWARE_ENDSTOPS requires at least one of the MAX_SOFTWARE_ENDSTOP_[XYZ] options." #endif #endif #if !defined(TARGET_LPC1768) && ( \ ENABLED(ENDSTOPPULLDOWNS) \ || ENABLED(ENDSTOPPULLDOWN_XMAX) \ || ENABLED(ENDSTOPPULLDOWN_YMAX) \ || ENABLED(ENDSTOPPULLDOWN_ZMAX) \ || ENABLED(ENDSTOPPULLDOWN_XMIN) \ || ENABLED(ENDSTOPPULLDOWN_YMIN) \ || ENABLED(ENDSTOPPULLDOWN_ZMIN) ) #error "PULLDOWN pin mode is not available on the selected board." #endif #if ENABLED(ENDSTOPPULLUPS) && ENABLED(ENDSTOPPULLDOWNS) #error "Enable only one of ENDSTOPPULLUPS or ENDSTOPPULLDOWNS." #elif ENABLED(FIL_RUNOUT_PULLUP) && ENABLED(FIL_RUNOUT_PULLDOWN) #error "Enable only one of FIL_RUNOUT_PULLUP or FIL_RUNOUT_PULLDOWN." #elif ENABLED(ENDSTOPPULLUP_XMAX) && ENABLED(ENDSTOPPULLDOWN_XMAX) #error "Enable only one of ENDSTOPPULLUP_X_MAX or ENDSTOPPULLDOWN_X_MAX." #elif ENABLED(ENDSTOPPULLUP_YMAX) && ENABLED(ENDSTOPPULLDOWN_YMAX) #error "Enable only one of ENDSTOPPULLUP_Y_MAX or ENDSTOPPULLDOWN_Y_MAX." #elif ENABLED(ENDSTOPPULLUP_ZMAX) && ENABLED(ENDSTOPPULLDOWN_ZMAX) #error "Enable only one of ENDSTOPPULLUP_Z_MAX or ENDSTOPPULLDOWN_Z_MAX." #elif ENABLED(ENDSTOPPULLUP_XMIN) && ENABLED(ENDSTOPPULLDOWN_XMIN) #error "Enable only one of ENDSTOPPULLUP_X_MIN or ENDSTOPPULLDOWN_X_MIN." #elif ENABLED(ENDSTOPPULLUP_YMIN) && ENABLED(ENDSTOPPULLDOWN_YMIN) #error "Enable only one of ENDSTOPPULLUP_Y_MIN or ENDSTOPPULLDOWN_Y_MIN." #elif ENABLED(ENDSTOPPULLUP_ZMIN) && ENABLED(ENDSTOPPULLDOWN_ZMIN) #error "Enable only one of ENDSTOPPULLUP_Z_MIN or ENDSTOPPULLDOWN_Z_MIN." #endif /** * Progress Bar */ #if ENABLED(LCD_PROGRESS_BAR) #if DISABLED(SDSUPPORT) && DISABLED(LCD_SET_PROGRESS_MANUALLY) #error "LCD_PROGRESS_BAR requires SDSUPPORT or LCD_SET_PROGRESS_MANUALLY." #elif DISABLED(ULTRA_LCD) #error "LCD_PROGRESS_BAR requires a character LCD." #elif ENABLED(DOGLCD) #error "LCD_PROGRESS_BAR does not apply to graphical displays." #elif ENABLED(FILAMENT_LCD_DISPLAY) #error "LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both." #endif #elif ENABLED(LCD_SET_PROGRESS_MANUALLY) && DISABLED(DOGLCD) #error "LCD_SET_PROGRESS_MANUALLY requires LCD_PROGRESS_BAR or Graphical LCD." #endif /** * Custom Boot and Status screens */ #if DISABLED(DOGLCD) && (ENABLED(SHOW_CUSTOM_BOOTSCREEN) || ENABLED(CUSTOM_STATUS_SCREEN_IMAGE)) #error "Graphical LCD is required for SHOW_CUSTOM_BOOTSCREEN and CUSTOM_STATUS_SCREEN_IMAGE." #endif /** * SD File Sorting */ #if ENABLED(SDCARD_SORT_ALPHA) #if SDSORT_LIMIT > 256 #error "SDSORT_LIMIT must be 256 or smaller." #elif SDSORT_LIMIT < 10 #error "SDSORT_LIMIT should be greater than 9 to be useful." #elif DISABLED(SDSORT_USES_RAM) #if ENABLED(SDSORT_DYNAMIC_RAM) #error "SDSORT_DYNAMIC_RAM requires SDSORT_USES_RAM (which reads the directory into RAM)." #elif ENABLED(SDSORT_CACHE_NAMES) #error "SDSORT_CACHE_NAMES requires SDSORT_USES_RAM (which reads the directory into RAM)." #endif #endif #if ENABLED(SDSORT_CACHE_NAMES) && DISABLED(SDSORT_DYNAMIC_RAM) #if SDSORT_CACHE_VFATS < 2 #error "SDSORT_CACHE_VFATS must be 2 or greater!" #elif SDSORT_CACHE_VFATS > MAX_VFAT_ENTRIES #undef SDSORT_CACHE_VFATS #define SDSORT_CACHE_VFATS MAX_VFAT_ENTRIES #warning "SDSORT_CACHE_VFATS was reduced to MAX_VFAT_ENTRIES!" #endif #endif #endif /** * I2C Position Encoders */ #if ENABLED(I2C_POSITION_ENCODERS) #if DISABLED(BABYSTEPPING) || DISABLED(BABYSTEP_XY) #error "I2C_POSITION_ENCODERS requires BABYSTEPPING and BABYSTEP_XY." #elif !WITHIN(I2CPE_ENCODER_CNT, 1, 5) #error "I2CPE_ENCODER_CNT must be between 1 and 5." #endif #endif /** * Babystepping */ #if ENABLED(BABYSTEPPING) #if ENABLED(SCARA) #error "BABYSTEPPING is not implemented for SCARA yet." #elif ENABLED(DELTA) && ENABLED(BABYSTEP_XY) #error "BABYSTEPPING only implemented for Z axis on deltabots." #elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && ENABLED(MESH_BED_LEVELING) #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination" #elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && !HAS_BED_PROBE #error "BABYSTEP_ZPROBE_OFFSET requires a probe." #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && !ENABLED(DOGLCD) #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a DOGLCD." #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && !ENABLED(BABYSTEP_ZPROBE_OFFSET) #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a BABYSTEP_ZPROBE_OFFSET." #endif #endif /** * Filament Runout needs one or more pins and either SD Support or Auto print start detection */ #if ENABLED(FILAMENT_RUNOUT_SENSOR) #if !PIN_EXISTS(FIL_RUNOUT) #error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN." #elif NUM_RUNOUT_SENSORS > E_STEPPERS #error "NUM_RUNOUT_SENSORS cannot exceed the number of E steppers." #elif NUM_RUNOUT_SENSORS > 1 && !PIN_EXISTS(FIL_RUNOUT2) #error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 1 requires FIL_RUNOUT2_PIN." #elif NUM_RUNOUT_SENSORS > 2 && !PIN_EXISTS(FIL_RUNOUT3) #error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 2 requires FIL_RUNOUT3_PIN." #elif NUM_RUNOUT_SENSORS > 3 && !PIN_EXISTS(FIL_RUNOUT4) #error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 3 requires FIL_RUNOUT4_PIN." #elif NUM_RUNOUT_SENSORS > 4 && !PIN_EXISTS(FIL_RUNOUT5) #error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 4 requires FIL_RUNOUT5_PIN." #elif DISABLED(SDSUPPORT) && DISABLED(PRINTJOB_TIMER_AUTOSTART) #error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART." #elif DISABLED(ADVANCED_PAUSE_FEATURE) static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR."); #endif #endif /** * Advanced Pause */ #if ENABLED(ADVANCED_PAUSE_FEATURE) #if !HAS_RESUME_CONTINUE #error "ADVANCED_PAUSE_FEATURE currently requires an LCD controller or EMERGENCY_PARSER." #elif ENABLED(EXTRUDER_RUNOUT_PREVENT) #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE." #elif ENABLED(PARK_HEAD_ON_PAUSE) && DISABLED(SDSUPPORT) && DISABLED(NEWPANEL) && DISABLED(EMERGENCY_PARSER) #error "PARK_HEAD_ON_PAUSE requires SDSUPPORT, EMERGENCY_PARSER, or an LCD controller." #elif ENABLED(HOME_BEFORE_FILAMENT_CHANGE) && DISABLED(PAUSE_PARK_NO_STEPPER_TIMEOUT) #error "HOME_BEFORE_FILAMENT_CHANGE requires PAUSE_PARK_NO_STEPPER_TIMEOUT." #elif DISABLED(NOZZLE_PARK_FEATURE) #error "ADVANCED_PAUSE_FEATURE requires NOZZLE_PARK_FEATURE." #elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_UNLOAD_LENGTH > EXTRUDE_MAXLENGTH #error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH." #elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_SLOW_LOAD_LENGTH > EXTRUDE_MAXLENGTH #error "FILAMENT_CHANGE_SLOW_LOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH." #elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_FAST_LOAD_LENGTH > EXTRUDE_MAXLENGTH #error "FILAMENT_CHANGE_FAST_LOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH." #endif #endif /** * Individual axis homing is useless for DELTAS */ #if ENABLED(INDIVIDUAL_AXIS_HOMING_MENU) && ENABLED(DELTA) #error "INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics." #endif /** * Options only for EXTRUDERS > 1 */ #if EXTRUDERS > 1 #if EXTRUDERS > 5 #error "Marlin supports a maximum of 5 EXTRUDERS." #endif #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) #error "EXTRUDERS must be 1 with TEMP_SENSOR_1_AS_REDUNDANT." #endif #if ENABLED(HEATERS_PARALLEL) #error "EXTRUDERS must be 1 with HEATERS_PARALLEL." #endif #elif ENABLED(MK2_MULTIPLEXER) #error "MK2_MULTIPLEXER requires 2 or more EXTRUDERS." #elif ENABLED(SINGLENOZZLE) #error "SINGLENOZZLE requires 2 or more EXTRUDERS." #endif /** * Sanity checking for the Průša MK2 Multiplexer */ #ifdef SNMM #error "SNMM is now MK2_MULTIPLEXER. Please update your configuration." #endif /** * A Dual Nozzle carriage with switching servo */ #if ENABLED(SWITCHING_NOZZLE) #if ENABLED(DUAL_X_CARRIAGE) #error "SWITCHING_NOZZLE and DUAL_X_CARRIAGE are incompatible." #elif ENABLED(SINGLENOZZLE) #error "SWITCHING_NOZZLE and SINGLENOZZLE are incompatible." #elif EXTRUDERS != 2 #error "SWITCHING_NOZZLE requires exactly 2 EXTRUDERS." #elif NUM_SERVOS < 1 #error "SWITCHING_NOZZLE requires NUM_SERVOS >= 1." #endif #endif /** * Single Stepper Dual Extruder with switching servo */ #if ENABLED(SWITCHING_EXTRUDER) && NUM_SERVOS < 1 #error "SWITCHING_EXTRUDER requires NUM_SERVOS >= 1." #endif /** * Mixing Extruder requirements */ #if ENABLED(MIXING_EXTRUDER) #if EXTRUDERS > 1 #error "MIXING_EXTRUDER currently only supports one extruder." #elif MIXING_STEPPERS < 2 #error "You must set MIXING_STEPPERS >= 2 for a mixing extruder." #elif ENABLED(FILAMENT_SENSOR) #error "MIXING_EXTRUDER is incompatible with FILAMENT_SENSOR. Comment out this line to use it anyway." #elif ENABLED(SWITCHING_EXTRUDER) #error "Please select either MIXING_EXTRUDER or SWITCHING_EXTRUDER, not both." #elif ENABLED(SINGLENOZZLE) #error "MIXING_EXTRUDER is incompatible with SINGLENOZZLE." #elif ENABLED(LIN_ADVANCE) #error "MIXING_EXTRUDER is incompatible with LIN_ADVANCE." #endif #endif /** * Linear Advance 1.5 - Check K value range */ #if ENABLED(LIN_ADVANCE) static_assert( WITHIN(LIN_ADVANCE_K, 0, 10), "LIN_ADVANCE_K must be a value from 0 to 10 (Changed in LIN_ADVANCE v1.5, Marlin 1.1.9)." ); #endif /** * Parking Extruder requirements */ #if ENABLED(PARKING_EXTRUDER) #if ENABLED(DUAL_X_CARRIAGE) #error "PARKING_EXTRUDER and DUAL_X_CARRIAGE are incompatible." #elif ENABLED(SINGLENOZZLE) #error "PARKING_EXTRUDER and SINGLENOZZLE are incompatible." #elif ENABLED(EXT_SOLENOID) #error "PARKING_EXTRUDER and EXT_SOLENOID are incompatible. (Pins are used twice.)" #elif EXTRUDERS != 2 #error "PARKING_EXTRUDER requires exactly 2 EXTRUDERS." #elif !PIN_EXISTS(SOL0) || !PIN_EXISTS(SOL1) #error "PARKING_EXTRUDER requires SOL0_PIN and SOL1_PIN." #elif !defined(PARKING_EXTRUDER_PARKING_X) #error "PARKING_EXTRUDER requires PARKING_EXTRUDER_PARKING_X." #elif !defined(PARKING_EXTRUDER_SECURITY_RAISE) #error "PARKING_EXTRUDER requires PARKING_EXTRUDER_SECURITY_RAISE." #elif PARKING_EXTRUDER_SECURITY_RAISE < 0 #error "PARKING_EXTRUDER_SECURITY_RAISE must be 0 or higher." #elif !defined(PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE, LOW, HIGH) #error "PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE must be defined as HIGH or LOW." #elif !defined(PARKING_EXTRUDER_SOLENOIDS_DELAY) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_DELAY, 0, 2000) #error "PARKING_EXTRUDER_SOLENOIDS_DELAY must be between 0 and 2000 (ms)." #endif #endif /** * Part-Cooling Fan Multiplexer requirements */ #if PIN_EXISTS(FANMUX1) #if !HAS_FANMUX #error "FANMUX0_PIN must be set before FANMUX1_PIN can be set." #endif #elif PIN_EXISTS(FANMUX2) #error "FANMUX0_PIN and FANMUX1_PIN must be set before FANMUX2_PIN can be set." #endif /** * Limited number of servos */ #if NUM_SERVOS > 4 #error "The maximum number of SERVOS in Marlin is 4." #endif /** * Servo deactivation depends on servo endstops, switching nozzle, or switching extruder */ #if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) && !HAS_Z_SERVO_PROBE && !defined(SWITCHING_NOZZLE_SERVO_NR) && !defined(SWITCHING_EXTRUDER_SERVO_NR) #error "Z_PROBE_SERVO_NR, switching nozzle, or switching extruder is required for DEACTIVATE_SERVOS_AFTER_MOVE." #endif /** * Required LCD language */ #if DISABLED(DOGLCD) && ENABLED(ULTRA_LCD) && !defined(DISPLAY_CHARSET_HD44780) #error "You must set DISPLAY_CHARSET_HD44780 to JAPANESE, WESTERN or CYRILLIC for your LCD controller." #endif /** * Bed Heating Options - PID vs Limit Switching */ #if ENABLED(PIDTEMPBED) && ENABLED(BED_LIMIT_SWITCHING) #error "To use BED_LIMIT_SWITCHING you must disable PIDTEMPBED." #endif /** * Kinematics */ /** * Allow only one kinematic type to be defined */ #if 1 < 0 \ + ENABLED(DELTA) \ + ENABLED(MORGAN_SCARA) \ + ENABLED(MAKERARM_SCARA) \ + ENABLED(COREXY) \ + ENABLED(COREXZ) \ + ENABLED(COREYZ) \ + ENABLED(COREYX) \ + ENABLED(COREZX) \ + ENABLED(COREZY) #error "Please enable only one of DELTA, MORGAN_SCARA, MAKERARM_SCARA, COREXY, COREYX, COREXZ, COREZX, COREYZ, or COREZY." #endif /** * Delta requirements */ #if ENABLED(DELTA) #if DISABLED(USE_XMAX_PLUG) && DISABLED(USE_YMAX_PLUG) && DISABLED(USE_ZMAX_PLUG) #error "You probably want to use Max Endstops for DELTA!" #elif ENABLED(ENABLE_LEVELING_FADE_HEIGHT) && DISABLED(AUTO_BED_LEVELING_BILINEAR) && !UBL_SEGMENTED #error "ENABLE_LEVELING_FADE_HEIGHT on DELTA requires AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL." #elif ENABLED(DELTA_AUTO_CALIBRATION) && !(HAS_BED_PROBE || ENABLED(ULTIPANEL)) #error "DELTA_AUTO_CALIBRATION requires a probe or LCD Controller." #elif ABL_GRID #if (GRID_MAX_POINTS_X & 1) == 0 || (GRID_MAX_POINTS_Y & 1) == 0 #error "DELTA requires GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y to be odd numbers." #elif GRID_MAX_POINTS_X < 3 #error "DELTA requires GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y to be 3 or higher." #endif #endif #endif /** * Probes */ /** * Allow only one probe option to be defined */ #if 1 < 0 \ + ENABLED(PROBE_MANUALLY) \ + ENABLED(FIX_MOUNTED_PROBE) \ + (HAS_Z_SERVO_PROBE && DISABLED(BLTOUCH)) \ + ENABLED(BLTOUCH) \ + ENABLED(SOLENOID_PROBE) \ + ENABLED(Z_PROBE_ALLEN_KEY) \ + ENABLED(Z_PROBE_SLED) #error "Please enable only one probe option: PROBE_MANUALLY, FIX_MOUNTED_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or Z Servo." #endif #if HAS_BED_PROBE /** * Z_PROBE_SLED is incompatible with DELTA */ #if ENABLED(Z_PROBE_SLED) && ENABLED(DELTA) #error "You cannot use Z_PROBE_SLED with DELTA." #endif /** * SOLENOID_PROBE requirements */ #if ENABLED(SOLENOID_PROBE) #if ENABLED(EXT_SOLENOID) #error "SOLENOID_PROBE is incompatible with EXT_SOLENOID." #elif !HAS_SOLENOID_1 #error "SOLENOID_PROBE requires SOL1_PIN. It can be added to your Configuration.h." #endif #endif /** * NUM_SERVOS is required for a Z servo probe */ #if HAS_Z_SERVO_PROBE #ifndef NUM_SERVOS #error "You must set NUM_SERVOS for a Z servo probe (Z_PROBE_SERVO_NR)." #elif Z_PROBE_SERVO_NR >= NUM_SERVOS #error "Z_PROBE_SERVO_NR must be smaller than NUM_SERVOS." #endif #endif /** * Require pin options and pins to be defined */ #if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) #if ENABLED(Z_MIN_PROBE_ENDSTOP) #error "Enable only one option: Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN." #elif DISABLED(USE_ZMIN_PLUG) #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires USE_ZMIN_PLUG to be enabled." #elif !HAS_Z_MIN #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires the Z_MIN_PIN to be defined." #elif ENABLED(Z_MIN_PROBE_ENDSTOP_INVERTING) != ENABLED(Z_MIN_ENDSTOP_INVERTING) #error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires Z_MIN_ENDSTOP_INVERTING to match Z_MIN_PROBE_ENDSTOP_INVERTING." #endif #elif ENABLED(Z_MIN_PROBE_ENDSTOP) #if !HAS_Z_MIN_PROBE_PIN #error "Z_MIN_PROBE_ENDSTOP requires the Z_MIN_PROBE_PIN to be defined." #endif #else #error "You must enable either Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use a probe." #endif /** * Make sure Z raise values are set */ #ifndef Z_CLEARANCE_DEPLOY_PROBE #error "You must define Z_CLEARANCE_DEPLOY_PROBE in your configuration." #elif !defined(Z_CLEARANCE_BETWEEN_PROBES) #error "You must define Z_CLEARANCE_BETWEEN_PROBES in your configuration." #elif Z_CLEARANCE_DEPLOY_PROBE < 0 #error "Probes need Z_CLEARANCE_DEPLOY_PROBE >= 0." #elif Z_CLEARANCE_BETWEEN_PROBES < 0 #error "Probes need Z_CLEARANCE_BETWEEN_PROBES >= 0." #elif Z_AFTER_PROBING < 0 #error "Probes need Z_AFTER_PROBING >= 0." #endif #if MULTIPLE_PROBING && MULTIPLE_PROBING < 2 #error "MULTIPLE_PROBING must be >= 2." #endif #if Z_PROBE_LOW_POINT > 0 #error "Z_PROBE_LOW_POINT must be less than or equal to 0." #endif #else /** * Require some kind of probe for bed leveling and probe testing */ #if OLDSCHOOL_ABL && !PROBE_SELECTED #error "Auto Bed Leveling requires one of these: PROBE_MANUALLY, FIX_MOUNTED_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or a Z Servo." #endif #if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST) #error "Z_MIN_PROBE_REPEATABILITY_TEST requires a probe: FIX_MOUNTED_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or Z Servo." #endif #endif /** * Allow only one bed leveling option to be defined */ #if 1 < 0 \ + ENABLED(AUTO_BED_LEVELING_LINEAR) \ + ENABLED(AUTO_BED_LEVELING_3POINT) \ + ENABLED(AUTO_BED_LEVELING_BILINEAR) \ + ENABLED(AUTO_BED_LEVELING_UBL) \ + ENABLED(MESH_BED_LEVELING) #error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL." #endif /** * Bed Leveling Requirements */ #if ENABLED(AUTO_BED_LEVELING_UBL) || ENABLED(AUTO_BED_LEVELING_3POINT) static_assert(WITHIN(PROBE_PT_1_X, MIN_PROBE_X, MAX_PROBE_X), "PROBE_PT_1_X is outside the probe region."); static_assert(WITHIN(PROBE_PT_2_X, MIN_PROBE_X, MAX_PROBE_X), "PROBE_PT_2_X is outside the probe region."); static_assert(WITHIN(PROBE_PT_3_X, MIN_PROBE_X, MAX_PROBE_X), "PROBE_PT_3_X is outside the probe region."); static_assert(WITHIN(PROBE_PT_1_Y, MIN_PROBE_Y, MAX_PROBE_Y), "PROBE_PT_1_Y is outside the probe region."); static_assert(WITHIN(PROBE_PT_2_Y, MIN_PROBE_Y, MAX_PROBE_Y), "PROBE_PT_2_Y is outside the probe region."); static_assert(WITHIN(PROBE_PT_3_Y, MIN_PROBE_Y, MAX_PROBE_Y), "PROBE_PT_3_Y is outside the probe region."); #endif #if ENABLED(AUTO_BED_LEVELING_UBL) /** * Unified Bed Leveling */ // Hide PROBE_MANUALLY from the rest of the code #undef PROBE_MANUALLY #if IS_SCARA #error "AUTO_BED_LEVELING_UBL does not yet support SCARA printers." #elif DISABLED(EEPROM_SETTINGS) #error "AUTO_BED_LEVELING_UBL requires EEPROM_SETTINGS. Please update your configuration." #elif !WITHIN(GRID_MAX_POINTS_X, 3, 15) || !WITHIN(GRID_MAX_POINTS_Y, 3, 15) #error "GRID_MAX_POINTS_[XY] must be a whole number between 3 and 15." #elif !defined(RESTORE_LEVELING_AFTER_G28) #error "AUTO_BED_LEVELING_UBL used to enable RESTORE_LEVELING_AFTER_G28. To keep this behavior enable RESTORE_LEVELING_AFTER_G28. Otherwise define it as 'false'." #endif #elif OLDSCHOOL_ABL /** * Auto Bed Leveling */ /** * Delta and SCARA have limited bed leveling options */ #if IS_SCARA && DISABLED(AUTO_BED_LEVELING_BILINEAR) #error "SCARA machines can only use the AUTO_BED_LEVELING_BILINEAR leveling option." #endif /** * Check auto bed leveling probe points */ #if ABL_GRID static_assert(LEFT_PROBE_BED_POSITION < RIGHT_PROBE_BED_POSITION, "LEFT_PROBE_BED_POSITION must be less than RIGHT_PROBE_BED_POSITION."); static_assert(FRONT_PROBE_BED_POSITION < BACK_PROBE_BED_POSITION, "FRONT_PROBE_BED_POSITION must be less than BACK_PROBE_BED_POSITION."); static_assert(LEFT_PROBE_BED_POSITION >= MIN_PROBE_X, "LEFT_PROBE_BED_POSITION is outside the probe region."); static_assert(RIGHT_PROBE_BED_POSITION <= MAX_PROBE_X, "RIGHT_PROBE_BED_POSITION is outside the probe region."); static_assert(FRONT_PROBE_BED_POSITION >= MIN_PROBE_Y, "FRONT_PROBE_BED_POSITION is outside the probe region."); static_assert(BACK_PROBE_BED_POSITION <= MAX_PROBE_Y, "BACK_PROBE_BED_POSITION is outside the probe region."); #endif // AUTO_BED_LEVELING_3POINT #elif ENABLED(MESH_BED_LEVELING) // Hide PROBE_MANUALLY from the rest of the code #undef PROBE_MANUALLY /** * Mesh Bed Leveling */ #if ENABLED(DELTA) #error "MESH_BED_LEVELING is not compatible with DELTA printers." #elif GRID_MAX_POINTS_X > 9 || GRID_MAX_POINTS_Y > 9 #error "GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y must be less than 10 for MBL." #endif #endif #if HAS_MESH static_assert(DEFAULT_ZJERK > 0.1, "Low DEFAULT_ZJERK values are incompatible with mesh-based leveling."); #elif ENABLED(G26_MESH_VALIDATION) #error "G26_MESH_VALIDATION requires MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_UBL." #endif #if ENABLED(MESH_EDIT_GFX_OVERLAY) && (DISABLED(AUTO_BED_LEVELING_UBL) || DISABLED(DOGLCD)) #error "MESH_EDIT_GFX_OVERLAY requires AUTO_BED_LEVELING_UBL and a Graphical LCD." #endif /** * LCD_BED_LEVELING requirements */ #if ENABLED(LCD_BED_LEVELING) #if DISABLED(ULTIPANEL) #error "LCD_BED_LEVELING requires an LCD controller." #elif !(ENABLED(MESH_BED_LEVELING) || (OLDSCHOOL_ABL && ENABLED(PROBE_MANUALLY))) #error "LCD_BED_LEVELING requires MESH_BED_LEVELING or ABL with PROBE_MANUALLY." #endif #endif /** * Homing */ #if X_HOME_BUMP_MM < 0 || Y_HOME_BUMP_MM < 0 || Z_HOME_BUMP_MM < 0 #error "[XYZ]_HOME_BUMP_MM must be greater than or equal to 0." #endif #if ENABLED(CODEPENDENT_XY_HOMING) #if ENABLED(QUICK_HOME) #error "QUICK_HOME is incompatible with CODEPENDENT_XY_HOMING." #elif IS_KINEMATIC #error "CODEPENDENT_XY_HOMING requires a Cartesian setup." #endif #endif /** * Make sure Z_SAFE_HOMING point is reachable */ #if ENABLED(Z_SAFE_HOMING) #if HAS_BED_PROBE static_assert(WITHIN(Z_SAFE_HOMING_X_POINT, MIN_PROBE_X, MAX_PROBE_X), "Z_SAFE_HOMING_X_POINT is outside the probe region."); static_assert(WITHIN(Z_SAFE_HOMING_Y_POINT, MIN_PROBE_Y, MAX_PROBE_Y), "Z_SAFE_HOMING_Y_POINT is outside the probe region."); #else static_assert(WITHIN(Z_SAFE_HOMING_X_POINT, X_MIN_POS, X_MAX_POS), "Z_SAFE_HOMING_X_POINT can't be reached by the nozzle."); static_assert(WITHIN(Z_SAFE_HOMING_Y_POINT, Y_MIN_POS, Y_MAX_POS), "Z_SAFE_HOMING_Y_POINT can't be reached by the nozzle."); #endif #endif // Z_SAFE_HOMING /** * Make sure DISABLE_[XYZ] compatible with selected homing options */ #if ENABLED(DISABLE_X) || ENABLED(DISABLE_Y) || ENABLED(DISABLE_Z) #if ENABLED(HOME_AFTER_DEACTIVATE) || ENABLED(Z_SAFE_HOMING) #error "DISABLE_[XYZ] is not compatible with HOME_AFTER_DEACTIVATE or Z_SAFE_HOMING." #endif #endif // DISABLE_[XYZ] /** * Filament Width Sensor */ #if ENABLED(FILAMENT_WIDTH_SENSOR) #if !HAS_FILAMENT_WIDTH_SENSOR #error "FILAMENT_WIDTH_SENSOR requires a FILWIDTH_PIN to be defined." #elif ENABLED(NO_VOLUMETRICS) #error "FILAMENT_WIDTH_SENSOR requires NO_VOLUMETRICS to be disabled." #endif #endif /** * ULTIPANEL encoder */ #if ENABLED(ULTIPANEL) && DISABLED(NEWPANEL) && DISABLED(SR_LCD_2W_NL) && !defined(SHIFT_CLK) #error "ULTIPANEL requires some kind of encoder." #endif #if ENCODER_PULSES_PER_STEP < 0 #error "ENCODER_PULSES_PER_STEP should not be negative, use REVERSE_MENU_DIRECTION instead." #endif /** * SAV_3DGLCD display options */ #if ENABLED(U8GLIB_SSD1306) && ENABLED(U8GLIB_SH1106) #error "Only enable one SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106." #endif /** * Allen Key * Deploying the Allen Key probe uses big moves in z direction. Too dangerous for an unhomed z-axis. */ #if ENABLED(Z_PROBE_ALLEN_KEY) && (Z_HOME_DIR < 0) && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) #error "You can't home to a z min endstop with a Z_PROBE_ALLEN_KEY" #endif /** * Dual X Carriage requirements */ #if ENABLED(DUAL_X_CARRIAGE) #if EXTRUDERS == 1 #error "DUAL_X_CARRIAGE requires 2 (or more) extruders." #elif CORE_IS_XY || CORE_IS_XZ #error "DUAL_X_CARRIAGE cannot be used with COREXY, COREYX, COREXZ, or COREZX." #elif !HAS_X2_ENABLE || !HAS_X2_STEP || !HAS_X2_DIR #error "DUAL_X_CARRIAGE requires X2 stepper pins to be defined." #elif !HAS_X_MAX #error "DUAL_X_CARRIAGE requires USE_XMAX_PLUG and an X Max Endstop." #elif !defined(X2_HOME_POS) || !defined(X2_MIN_POS) || !defined(X2_MAX_POS) #error "DUAL_X_CARRIAGE requires X2_HOME_POS, X2_MIN_POS, and X2_MAX_POS." #elif X_HOME_DIR != -1 || X2_HOME_DIR != 1 #error "DUAL_X_CARRIAGE requires X_HOME_DIR -1 and X2_HOME_DIR 1." #endif #endif // DUAL_X_CARRIAGE /** * Make sure auto fan pins don't conflict with the fan pin */ #if HAS_AUTO_FAN #if HAS_FAN0 #if E0_AUTO_FAN_PIN == FAN_PIN #error "You cannot set E0_AUTO_FAN_PIN equal to FAN_PIN." #elif E1_AUTO_FAN_PIN == FAN_PIN #error "You cannot set E1_AUTO_FAN_PIN equal to FAN_PIN." #elif E2_AUTO_FAN_PIN == FAN_PIN #error "You cannot set E2_AUTO_FAN_PIN equal to FAN_PIN." #elif E3_AUTO_FAN_PIN == FAN_PIN #error "You cannot set E3_AUTO_FAN_PIN equal to FAN_PIN." #endif #endif #endif #if HAS_FAN0 && CONTROLLER_FAN_PIN == FAN_PIN #error "You cannot set CONTROLLER_FAN_PIN equal to FAN_PIN." #endif #if ENABLED(USE_CONTROLLER_FAN) #if !HAS_CONTROLLER_FAN #error "USE_CONTROLLER_FAN requires a CONTROLLER_FAN_PIN. Define in Configuration_adv.h." #elif E0_AUTO_FAN_PIN == CONTROLLER_FAN_PIN #error "You cannot set E0_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." #elif E1_AUTO_FAN_PIN == CONTROLLER_FAN_PIN #error "You cannot set E1_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." #elif E2_AUTO_FAN_PIN == CONTROLLER_FAN_PIN #error "You cannot set E2_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." #elif E3_AUTO_FAN_PIN == CONTROLLER_FAN_PIN #error "You cannot set E3_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN." #endif #endif /** * Test Heater, Temp Sensor, and Extruder Pins; Sensor Type must also be set. */ #if !HAS_HEATER_0 #error "HEATER_0_PIN not defined for this board." #elif !PIN_EXISTS(TEMP_0) && !(defined(MAX6675_SS) && MAX6675_SS >= 0) #error "TEMP_0_PIN not defined for this board." #elif ((defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && (!PIN_EXISTS(E0_STEP) || !PIN_EXISTS(E0_DIR))) #error "E0_STEP_PIN or E0_DIR_PIN not defined for this board." #elif ( !(defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && (!PIN_EXISTS(E0_STEP) || !PIN_EXISTS(E0_DIR) || !PIN_EXISTS(E0_ENABLE))) #error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board." #elif TEMP_SENSOR_0 == 0 #error "TEMP_SENSOR_0 is required." #endif // Pins are required for heaters #if ENABLED(HEATER_0_USES_MAX6675) && !(defined(MAX6675_SS) && MAX6675_SS >= 0) #error "MAX6675_SS (required for TEMP_SENSOR_0) not defined for this board." #elif (HOTENDS > 1 || ENABLED(HEATERS_PARALLEL)) && !HAS_HEATER_1 #error "HEATER_1_PIN not defined for this board." #endif #if HOTENDS > 1 #if TEMP_SENSOR_1 == 0 #error "TEMP_SENSOR_1 is required with 2 or more HOTENDS." #elif !PIN_EXISTS(TEMP_1) #error "TEMP_1_PIN not defined for this board." #endif #if HOTENDS > 2 #if TEMP_SENSOR_2 == 0 #error "TEMP_SENSOR_2 is required with 3 or more HOTENDS." #elif !HAS_HEATER_2 #error "HEATER_2_PIN not defined for this board." #elif !PIN_EXISTS(TEMP_2) #error "TEMP_2_PIN not defined for this board." #endif #if HOTENDS > 3 #if TEMP_SENSOR_3 == 0 #error "TEMP_SENSOR_3 is required with 4 or more HOTENDS." #elif !HAS_HEATER_3 #error "HEATER_3_PIN not defined for this board." #elif !PIN_EXISTS(TEMP_3) #error "TEMP_3_PIN not defined for this board." #endif #if HOTENDS > 4 #if TEMP_SENSOR_4 == 0 #error "TEMP_SENSOR_4 is required with 5 HOTENDS." #elif !HAS_HEATER_4 #error "HEATER_4_PIN not defined for this board." #elif !PIN_EXISTS(TEMP_4) #error "TEMP_4_PIN not defined for this board." #endif #elif TEMP_SENSOR_4 != 0 #error "TEMP_SENSOR_4 shouldn't be set with only 4 HOTENDS." #endif #elif TEMP_SENSOR_3 != 0 #error "TEMP_SENSOR_3 shouldn't be set with only 3 HOTENDS." #elif TEMP_SENSOR_4 != 0 #error "TEMP_SENSOR_4 shouldn't be set with only 3 HOTENDS." #endif #elif TEMP_SENSOR_2 != 0 #error "TEMP_SENSOR_2 shouldn't be set with only 2 HOTENDS." #elif TEMP_SENSOR_3 != 0 #error "TEMP_SENSOR_3 shouldn't be set with only 2 HOTENDS." #elif TEMP_SENSOR_4 != 0 #error "TEMP_SENSOR_4 shouldn't be set with only 2 HOTENDS." #endif #elif TEMP_SENSOR_1 != 0 && DISABLED(TEMP_SENSOR_1_AS_REDUNDANT) #error "TEMP_SENSOR_1 shouldn't be set with only 1 HOTEND." #elif TEMP_SENSOR_2 != 0 #error "TEMP_SENSOR_2 shouldn't be set with only 1 HOTEND." #elif TEMP_SENSOR_3 != 0 #error "TEMP_SENSOR_3 shouldn't be set with only 1 HOTEND." #elif TEMP_SENSOR_4 != 0 #error "TEMP_SENSOR_4 shouldn't be set with only 1 HOTEND." #endif #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) && TEMP_SENSOR_1 == 0 #error "TEMP_SENSOR_1 is required with TEMP_SENSOR_1_AS_REDUNDANT." #endif /** * Temperature status LEDs */ #if ENABLED(TEMP_STAT_LEDS) && !PIN_EXISTS(STAT_LED_RED) && !PIN_EXISTS(STAT_LED_BLUE) #error "TEMP_STAT_LEDS requires STAT_LED_RED_PIN or STAT_LED_BLUE_PIN, preferably both." #endif /** * Basic 2-nozzle duplication mode */ #if ENABLED(DUAL_NOZZLE_DUPLICATION_MODE) #if HOTENDS != 2 #error "DUAL_NOZZLE_DUPLICATION_MODE requires exactly 2 hotends." #elif ENABLED(DUAL_X_CARRIAGE) #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with DUAL_X_CARRIAGE." #elif ENABLED(SINGLENOZZLE) #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SINGLENOZZLE." #elif ENABLED(MIXING_EXTRUDER) #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with MIXING_EXTRUDER." #elif ENABLED(SWITCHING_EXTRUDER) #error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SWITCHING_EXTRUDER." #endif #endif /** * Test Extruder Stepper Pins */ #if DISABLED(MK2_MULTIPLEXER) // MK2_MULTIPLEXER uses E0 stepper only #if E_STEPPERS > 4 #if !PIN_EXISTS(E4_STEP) || !PIN_EXISTS(E4_DIR) || !PIN_EXISTS(E4_ENABLE) #error "E4_STEP_PIN, E4_DIR_PIN, or E4_ENABLE_PIN not defined for this board." #endif #elif E_STEPPERS > 3 #if !PIN_EXISTS(E3_STEP) || !PIN_EXISTS(E3_DIR) || !PIN_EXISTS(E3_ENABLE) #error "E3_STEP_PIN, E3_DIR_PIN, or E3_ENABLE_PIN not defined for this board." #endif #elif E_STEPPERS > 2 #if !PIN_EXISTS(E2_STEP) || !PIN_EXISTS(E2_DIR) || !PIN_EXISTS(E2_ENABLE) #error "E2_STEP_PIN, E2_DIR_PIN, or E2_ENABLE_PIN not defined for this board." #endif #elif E_STEPPERS > 1 #if !PIN_EXISTS(E1_STEP) || !PIN_EXISTS(E1_DIR) || !PIN_EXISTS(E1_ENABLE) #error "E1_STEP_PIN, E1_DIR_PIN, or E1_ENABLE_PIN not defined for this board." #endif #endif #endif /** * Endstop Tests */ #define _PLUG_UNUSED_TEST(AXIS,PLUG) (DISABLED(USE_##PLUG##MIN_PLUG) && DISABLED(USE_##PLUG##MAX_PLUG) && !(ENABLED(AXIS##_DUAL_ENDSTOPS) && WITHIN(AXIS##2_USE_ENDSTOP, _##PLUG##MAX_, _##PLUG##MIN_))) #define _AXIS_PLUG_UNUSED_TEST(AXIS) (_PLUG_UNUSED_TEST(AXIS,X) && _PLUG_UNUSED_TEST(AXIS,Y) && _PLUG_UNUSED_TEST(AXIS,Z)) // At least 3 endstop plugs must be used #if _AXIS_PLUG_UNUSED_TEST(X) #error "You must enable USE_XMIN_PLUG or USE_XMAX_PLUG." #endif #if _AXIS_PLUG_UNUSED_TEST(Y) #error "You must enable USE_YMIN_PLUG or USE_YMAX_PLUG." #endif #if _AXIS_PLUG_UNUSED_TEST(Z) #error "You must enable USE_ZMIN_PLUG or USE_ZMAX_PLUG." #endif // Delta and Cartesian use 3 homing endstops #if !IS_SCARA #if X_HOME_DIR < 0 && DISABLED(USE_XMIN_PLUG) #error "Enable USE_XMIN_PLUG when homing X to MIN." #elif X_HOME_DIR > 0 && DISABLED(USE_XMAX_PLUG) #error "Enable USE_XMAX_PLUG when homing X to MAX." #elif Y_HOME_DIR < 0 && DISABLED(USE_YMIN_PLUG) #error "Enable USE_YMIN_PLUG when homing Y to MIN." #elif Y_HOME_DIR > 0 && DISABLED(USE_YMAX_PLUG) #error "Enable USE_YMAX_PLUG when homing Y to MAX." #endif #endif #if Z_HOME_DIR < 0 && DISABLED(USE_ZMIN_PLUG) #error "Enable USE_ZMIN_PLUG when homing Z to MIN." #elif Z_HOME_DIR > 0 && DISABLED(USE_ZMAX_PLUG) #error "Enable USE_ZMAX_PLUG when homing Z to MAX." #endif // Dual endstops requirements #if ENABLED(X_DUAL_ENDSTOPS) #if !X2_USE_ENDSTOP #error "You must set X2_USE_ENDSTOP with X_DUAL_ENDSTOPS." #elif X2_USE_ENDSTOP == _X_MIN_ && DISABLED(USE_XMIN_PLUG) #error "USE_XMIN_PLUG is required when X2_USE_ENDSTOP is _X_MIN_." #elif X2_USE_ENDSTOP == _X_MAX_ && DISABLED(USE_XMAX_PLUG) #error "USE_XMAX_PLUG is required when X2_USE_ENDSTOP is _X_MAX_." #elif X2_USE_ENDSTOP == _Y_MIN_ && DISABLED(USE_YMIN_PLUG) #error "USE_YMIN_PLUG is required when X2_USE_ENDSTOP is _Y_MIN_." #elif X2_USE_ENDSTOP == _Y_MAX_ && DISABLED(USE_YMAX_PLUG) #error "USE_YMAX_PLUG is required when X2_USE_ENDSTOP is _Y_MAX_." #elif X2_USE_ENDSTOP == _Z_MIN_ && DISABLED(USE_ZMIN_PLUG) #error "USE_ZMIN_PLUG is required when X2_USE_ENDSTOP is _Z_MIN_." #elif X2_USE_ENDSTOP == _Z_MAX_ && DISABLED(USE_ZMAX_PLUG) #error "USE_ZMAX_PLUG is required when X2_USE_ENDSTOP is _Z_MAX_." #elif !HAS_X2_MIN && !HAS_X2_MAX #error "X2_USE_ENDSTOP has been assigned to a nonexistent endstop!" #elif ENABLED(DELTA) #error "X_DUAL_ENDSTOPS is not compatible with DELTA." #endif #endif #if ENABLED(Y_DUAL_ENDSTOPS) #if !Y2_USE_ENDSTOP #error "You must set Y2_USE_ENDSTOP with Y_DUAL_ENDSTOPS." #elif Y2_USE_ENDSTOP == _X_MIN_ && DISABLED(USE_XMIN_PLUG) #error "USE_XMIN_PLUG is required when Y2_USE_ENDSTOP is _X_MIN_." #elif Y2_USE_ENDSTOP == _X_MAX_ && DISABLED(USE_XMAX_PLUG) #error "USE_XMAX_PLUG is required when Y2_USE_ENDSTOP is _X_MAX_." #elif Y2_USE_ENDSTOP == _Y_MIN_ && DISABLED(USE_YMIN_PLUG) #error "USE_YMIN_PLUG is required when Y2_USE_ENDSTOP is _Y_MIN_." #elif Y2_USE_ENDSTOP == _Y_MAX_ && DISABLED(USE_YMAX_PLUG) #error "USE_YMAX_PLUG is required when Y2_USE_ENDSTOP is _Y_MAX_." #elif Y2_USE_ENDSTOP == _Z_MIN_ && DISABLED(USE_ZMIN_PLUG) #error "USE_ZMIN_PLUG is required when Y2_USE_ENDSTOP is _Z_MIN_." #elif Y2_USE_ENDSTOP == _Z_MAX_ && DISABLED(USE_ZMAX_PLUG) #error "USE_ZMAX_PLUG is required when Y2_USE_ENDSTOP is _Z_MAX_." #elif !HAS_Y2_MIN && !HAS_Y2_MAX #error "Y2_USE_ENDSTOP has been assigned to a nonexistent endstop!" #elif ENABLED(DELTA) #error "Y_DUAL_ENDSTOPS is not compatible with DELTA." #endif #endif #if ENABLED(Z_DUAL_ENDSTOPS) #if !Z2_USE_ENDSTOP #error "You must set Z2_USE_ENDSTOP with Z_DUAL_ENDSTOPS." #elif Z2_USE_ENDSTOP == _X_MIN_ && DISABLED(USE_XMIN_PLUG) #error "USE_XMIN_PLUG is required when Z2_USE_ENDSTOP is _X_MIN_." #elif Z2_USE_ENDSTOP == _X_MAX_ && DISABLED(USE_XMAX_PLUG) #error "USE_XMAX_PLUG is required when Z2_USE_ENDSTOP is _X_MAX_." #elif Z2_USE_ENDSTOP == _Y_MIN_ && DISABLED(USE_YMIN_PLUG) #error "USE_YMIN_PLUG is required when Z2_USE_ENDSTOP is _Y_MIN_." #elif Z2_USE_ENDSTOP == _Y_MAX_ && DISABLED(USE_YMAX_PLUG) #error "USE_YMAX_PLUG is required when Z2_USE_ENDSTOP is _Y_MAX_." #elif Z2_USE_ENDSTOP == _Z_MIN_ && DISABLED(USE_ZMIN_PLUG) #error "USE_ZMIN_PLUG is required when Z2_USE_ENDSTOP is _Z_MIN_." #elif Z2_USE_ENDSTOP == _Z_MAX_ && DISABLED(USE_ZMAX_PLUG) #error "USE_ZMAX_PLUG is required when Z2_USE_ENDSTOP is _Z_MAX_." #elif !HAS_Z2_MIN && !HAS_Z2_MAX #error "Z2_USE_ENDSTOP has been assigned to a nonexistent endstop!" #elif ENABLED(DELTA) #error "Z_DUAL_ENDSTOPS is not compatible with DELTA." #endif #endif /** * emergency-command parser */ #if ENABLED(EMERGENCY_PARSER) && defined(__AVR__) && defined(USBCON) #error "EMERGENCY_PARSER does not work on boards with AT90USB processors (USBCON)." #endif /** * I2C bus */ #if ENABLED(EXPERIMENTAL_I2CBUS) && I2C_SLAVE_ADDRESS > 0 #if I2C_SLAVE_ADDRESS < 8 #error "I2C_SLAVE_ADDRESS can't be less than 8. (Addresses 0 - 7 are reserved.)" #elif I2C_SLAVE_ADDRESS > 127 #error "I2C_SLAVE_ADDRESS can't be over 127. (Only 7 bits allowed.)" #endif #endif /** * G38 Probe Target */ #if ENABLED(G38_PROBE_TARGET) #if !HAS_BED_PROBE #error "G38_PROBE_TARGET requires a bed probe." #elif !IS_CARTESIAN #error "G38_PROBE_TARGET requires a Cartesian machine." #endif #endif /** * RGB_LED Requirements */ #define _RGB_TEST (PIN_EXISTS(RGB_LED_R) && PIN_EXISTS(RGB_LED_G) && PIN_EXISTS(RGB_LED_B)) #if ENABLED(RGB_LED) #if !_RGB_TEST #error "RGB_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, and RGB_LED_B_PIN." #elif ENABLED(RGBW_LED) #error "Please enable only one of RGB_LED and RGBW_LED." #endif #elif ENABLED(RGBW_LED) #if !(_RGB_TEST && PIN_EXISTS(RGB_LED_W)) #error "RGBW_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, RGB_LED_B_PIN, and RGB_LED_W_PIN." #endif #elif ENABLED(NEOPIXEL_LED) #if !(PIN_EXISTS(NEOPIXEL) && NEOPIXEL_PIXELS > 0) #error "NEOPIXEL_LED requires NEOPIXEL_PIN and NEOPIXEL_PIXELS." #endif #elif ENABLED(PRINTER_EVENT_LEDS) && DISABLED(BLINKM) && DISABLED(PCA9632) && DISABLED(NEOPIXEL_LED) #error "PRINTER_EVENT_LEDS requires BLINKM, PCA9632, RGB_LED, RGBW_LED or NEOPIXEL_LED." #endif /** * Auto Fan check for PWM pins */ #if HAS_AUTO_FAN && EXTRUDER_AUTO_FAN_SPEED != 255 #define AF_ERR_SUFF "_AUTO_FAN_PIN is not a PWM pin. Set EXTRUDER_AUTO_FAN_SPEED to 255." #if HAS_AUTO_FAN_0 static_assert(GET_TIMER(E0_AUTO_FAN_PIN), "E0" AF_ERR_SUFF); #elif HAS_AUTO_FAN_1 static_assert(GET_TIMER(E1_AUTO_FAN_PIN), "E1" AF_ERR_SUFF); #elif HAS_AUTO_FAN_2 static_assert(GET_TIMER(E2_AUTO_FAN_PIN), "E2" AF_ERR_SUFF); #elif HAS_AUTO_FAN_3 static_assert(GET_TIMER(E3_AUTO_FAN_PIN), "E3" AF_ERR_SUFF); #endif #endif /** * Make sure only one display is enabled * * Note: BQ_LCD_SMART_CONTROLLER => REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER => REPRAP_DISCOUNT_SMART_CONTROLLER * SAV_3DGLCD => U8GLIB_SH1106 => ULTIMAKERCONTROLLER * MKS_12864OLED => U8GLIB_SH1106 => ULTIMAKERCONTROLLER * MKS_12864OLED_SSD1306 => U8GLIB_SSD1306 => ULTIMAKERCONTROLLER * MKS_MINI_12864 => MINIPANEL * miniVIKI => ULTIMAKERCONTROLLER * VIKI2 => ULTIMAKERCONTROLLER * ELB_FULL_GRAPHIC_CONTROLLER => ULTIMAKERCONTROLLER * AZSMZ_12864 => ULTIMAKERCONTROLLER * PANEL_ONE => ULTIMAKERCONTROLLER */ #if 1 < 0 \ + ( ENABLED(ULTIMAKERCONTROLLER) \ && DISABLED(SAV_3DGLCD) \ && DISABLED(miniVIKI) \ && DISABLED(VIKI2) \ && DISABLED(ELB_FULL_GRAPHIC_CONTROLLER) \ && DISABLED(AZSMZ_12864) \ && DISABLED(PANEL_ONE) \ && DISABLED(MKS_12864OLED) \ && DISABLED(MKS_12864OLED_SSD1306) ) \ + ( ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) \ && DISABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) \ && DISABLED(LCD_FOR_MELZI) \ && DISABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) \ && DISABLED(MKS_12864OLED) \ && DISABLED(MKS_12864OLED_SSD1306) ) \ + (ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && DISABLED(BQ_LCD_SMART_CONTROLLER)) \ + ENABLED(LCD_FOR_MELZI) \ + ENABLED(MKS_12864OLED) \ + ENABLED(MKS_12864OLED_SSD1306) \ + ENABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) \ + ENABLED(CARTESIO_UI) \ + ENABLED(PANEL_ONE) \ + ENABLED(MAKRPANEL) \ + ENABLED(REPRAPWORLD_GRAPHICAL_LCD) \ + ENABLED(VIKI2) \ + ENABLED(miniVIKI) \ + ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) \ + ENABLED(AZSMZ_12864) \ + ENABLED(G3D_PANEL) \ + (ENABLED(MINIPANEL) && DISABLED(MKS_MINI_12864)) \ + ENABLED(MKS_MINI_12864) \ + (ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(CARTESIO_UI) && DISABLED(ZONESTAR_LCD)) \ + ENABLED(RIGIDBOT_PANEL) \ + ENABLED(RA_CONTROL_PANEL) \ + ENABLED(LCD_SAINSMART_I2C_1602) \ + ENABLED(LCD_SAINSMART_I2C_2004) \ + ENABLED(LCM1602) \ + ENABLED(LCD_I2C_PANELOLU2) \ + ENABLED(LCD_I2C_VIKI) \ + (ENABLED(U8GLIB_SSD1306) && DISABLED(OLED_PANEL_TINYBOY2) && DISABLED(MKS_12864OLED_SSD1306)) \ + ENABLED(SAV_3DLCD) \ + ENABLED(BQ_LCD_SMART_CONTROLLER) \ + ENABLED(SAV_3DGLCD) \ + ENABLED(OLED_PANEL_TINYBOY2) \ + ENABLED(ZONESTAR_LCD) \ + ENABLED(ULTI_CONTROLLER) #error "Please select no more than one LCD controller option." #endif /** * Make sure HAVE_TMC26X is warranted */ #if ENABLED(HAVE_TMC26X) && !( \ ENABLED( X_IS_TMC26X ) \ || ENABLED( X2_IS_TMC26X ) \ || ENABLED( Y_IS_TMC26X ) \ || ENABLED( Y2_IS_TMC26X ) \ || ENABLED( Z_IS_TMC26X ) \ || ENABLED( Z2_IS_TMC26X ) \ || ENABLED( E0_IS_TMC26X ) \ || ENABLED( E1_IS_TMC26X ) \ || ENABLED( E2_IS_TMC26X ) \ || ENABLED( E3_IS_TMC26X ) \ || ENABLED( E4_IS_TMC26X ) \ ) #error "HAVE_TMC26X requires at least one TMC26X stepper to be set." #endif /** * Make sure HAVE_TMC2130 is warranted */ #if ENABLED(HAVE_TMC2130) #if !( ENABLED( X_IS_TMC2130 ) \ || ENABLED( X2_IS_TMC2130 ) \ || ENABLED( Y_IS_TMC2130 ) \ || ENABLED( Y2_IS_TMC2130 ) \ || ENABLED( Z_IS_TMC2130 ) \ || ENABLED( Z2_IS_TMC2130 ) \ || ENABLED( E0_IS_TMC2130 ) \ || ENABLED( E1_IS_TMC2130 ) \ || ENABLED( E2_IS_TMC2130 ) \ || ENABLED( E3_IS_TMC2130 ) \ || ENABLED( E4_IS_TMC2130 ) ) #error "HAVE_TMC2130 requires at least one TMC2130 stepper to be set." #elif ENABLED(HYBRID_THRESHOLD) && DISABLED(STEALTHCHOP) #error "Enable STEALTHCHOP to use HYBRID_THRESHOLD." #endif #if ENABLED(X_IS_TMC2130) && !PIN_EXISTS(X_CS) #error "X_CS_PIN is required for X_IS_TMC2130. Define X_CS_PIN in Configuration_adv.h." #elif ENABLED(X2_IS_TMC2130) && !PIN_EXISTS(X2_CS) #error "X2_CS_PIN is required for X2_IS_TMC2130. Define X2_CS_PIN in Configuration_adv.h." #elif ENABLED(Y_IS_TMC2130) && !PIN_EXISTS(Y_CS) #error "Y_CS_PIN is required for Y_IS_TMC2130. Define Y_CS_PIN in Configuration_adv.h." #elif ENABLED(Y2_IS_TMC2130) && !PIN_EXISTS(Y2_CS) #error "Y2_CS_PIN is required for Y2_IS_TMC2130. Define Y2_CS_PIN in Configuration_adv.h." #elif ENABLED(Z_IS_TMC2130) && !PIN_EXISTS(Z_CS) #error "Z_CS_PIN is required for Z_IS_TMC2130. Define Z_CS_PIN in Configuration_adv.h." #elif ENABLED(Z2_IS_TMC2130) && !PIN_EXISTS(Z2_CS) #error "Z2_CS_PIN is required for Z2_IS_TMC2130. Define Z2_CS_PIN in Configuration_adv.h." #elif ENABLED(E0_IS_TMC2130) && !PIN_EXISTS(E0_CS) #error "E0_CS_PIN is required for E0_IS_TMC2130. Define E0_CS_PIN in Configuration_adv.h." #elif ENABLED(E1_IS_TMC2130) && !PIN_EXISTS(E1_CS) #error "E1_CS_PIN is required for E1_IS_TMC2130. Define E1_CS_PIN in Configuration_adv.h." #elif ENABLED(E2_IS_TMC2130) && !PIN_EXISTS(E2_CS) #error "E2_CS_PIN is required for E2_IS_TMC2130. Define E2_CS_PIN in Configuration_adv.h." #elif ENABLED(E3_IS_TMC2130) && !PIN_EXISTS(E3_CS) #error "E3_CS_PIN is required for E3_IS_TMC2130. Define E3_CS_PIN in Configuration_adv.h." #elif ENABLED(E4_IS_TMC2130) && !PIN_EXISTS(E4_CS) #error "E4_CS_PIN is required for E4_IS_TMC2130. Define E4_CS_PIN in Configuration_adv.h." #endif #if ENABLED(SENSORLESS_HOMING) // Require STEALTHCHOP for SENSORLESS_HOMING on DELTA as the transition from spreadCycle to stealthChop // is necessary in order to reset the stallGuard indication between the initial movement of all three // towers to +Z and the individual homing of each tower. This restriction can be removed once a means of // clearing the stallGuard activated status is found. #if ENABLED(DELTA) && !ENABLED(STEALTHCHOP) #error "SENSORLESS_HOMING on DELTA currently requires STEALTHCHOP." #elif X_HOME_DIR == -1 && DISABLED(X_MIN_ENDSTOP_INVERTING) #error "SENSORLESS_HOMING requires X_MIN_ENDSTOP_INVERTING when homing to X_MIN." #elif X_HOME_DIR == 1 && DISABLED(X_MAX_ENDSTOP_INVERTING) #error "SENSORLESS_HOMING requires X_MAX_ENDSTOP_INVERTING when homing to X_MAX." #elif Y_HOME_DIR == -1 && DISABLED(Y_MIN_ENDSTOP_INVERTING) #error "SENSORLESS_HOMING requires Y_MIN_ENDSTOP_INVERTING when homing to Y_MIN." #elif Y_HOME_DIR == 1 && DISABLED(Y_MAX_ENDSTOP_INVERTING) #error "SENSORLESS_HOMING requires Y_MAX_ENDSTOP_INVERTING when homing to Y_MAX." #endif #endif // Sensorless homing is required for both combined steppers in an H-bot #if CORE_IS_XY && X_SENSORLESS != Y_SENSORLESS #error "CoreXY requires both X and Y to use sensorless homing if either does." #elif CORE_IS_XZ && X_SENSORLESS != Z_SENSORLESS #error "CoreXZ requires both X and Z to use sensorless homing if either does." #elif CORE_IS_YZ && Y_SENSORLESS != Z_SENSORLESS #error "CoreYZ requires both Y and Z to use sensorless homing if either does." #endif #elif ENABLED(SENSORLESS_HOMING) #error "SENSORLESS_HOMING requires TMC2130 stepper drivers." #endif /** * Make sure HAVE_TMC2208 is warranted */ #if ENABLED(HAVE_TMC2208) && !( \ ENABLED( X_IS_TMC2208 ) \ || ENABLED( X2_IS_TMC2208 ) \ || ENABLED( Y_IS_TMC2208 ) \ || ENABLED( Y2_IS_TMC2208 ) \ || ENABLED( Z_IS_TMC2208 ) \ || ENABLED( Z2_IS_TMC2208 ) \ || ENABLED( E0_IS_TMC2208 ) \ || ENABLED( E1_IS_TMC2208 ) \ || ENABLED( E2_IS_TMC2208 ) \ || ENABLED( E3_IS_TMC2208 ) ) #error "HAVE_TMC2208 requires at least one TMC2208 stepper to be set." #endif /** * TMC2208 software UART and ENDSTOP_INTERRUPTS both use pin change interrupts (PCI) */ #if ENABLED(HAVE_TMC2208) && ENABLED(ENDSTOP_INTERRUPTS_FEATURE) && !( \ defined(X_HARDWARE_SERIAL ) \ || defined(X2_HARDWARE_SERIAL) \ || defined(Y_HARDWARE_SERIAL ) \ || defined(Y2_HARDWARE_SERIAL) \ || defined(Z_HARDWARE_SERIAL ) \ || defined(Z2_HARDWARE_SERIAL) \ || defined(E0_HARDWARE_SERIAL) \ || defined(E1_HARDWARE_SERIAL) \ || defined(E2_HARDWARE_SERIAL) \ || defined(E3_HARDWARE_SERIAL) \ || defined(E4_HARDWARE_SERIAL) ) #error "select hardware UART for TMC2208 to use both TMC2208 and ENDSTOP_INTERRUPTS_FEATURE." #endif #if ENABLED(HYBRID_THRESHOLD) && DISABLED(STEALTHCHOP) #error "Enable STEALTHCHOP to use HYBRID_THRESHOLD." #endif #if ENABLED(TMC_Z_CALIBRATION) && !Z_IS_TRINAMIC && !Z2_IS_TRINAMIC #error "TMC_Z_CALIBRATION requires at least one TMC driver on Z axis" #endif /** * Make sure HAVE_L6470DRIVER is warranted */ #if ENABLED(HAVE_L6470DRIVER) && !( \ ENABLED( X_IS_L6470 ) \ || ENABLED( X2_IS_L6470 ) \ || ENABLED( Y_IS_L6470 ) \ || ENABLED( Y2_IS_L6470 ) \ || ENABLED( Z_IS_L6470 ) \ || ENABLED( Z2_IS_L6470 ) \ || ENABLED( E0_IS_L6470 ) \ || ENABLED( E1_IS_L6470 ) \ || ENABLED( E2_IS_L6470 ) \ || ENABLED( E3_IS_L6470 ) \ || ENABLED( E4_IS_L6470 ) \ ) #error "HAVE_L6470DRIVER requires at least one L6470 stepper to be set." #endif /** * Check that each axis has only one driver selected */ #if 1 < 0 \ + ENABLED(X_IS_TMC26X) \ + ENABLED(X_IS_TMC2130) \ + ENABLED(X_IS_TMC2208) \ + ENABLED(X_IS_L6470) #error "Please enable only one stepper driver for the X axis." #endif #if 1 < 0 \ + ENABLED(X2_IS_TMC26X) \ + ENABLED(X2_IS_TMC2130) \ + ENABLED(X2_IS_TMC2208) \ + ENABLED(X2_IS_L6470) #error "Please enable only one stepper driver for the X2 axis." #endif #if 1 < 0 \ + ENABLED(Y_IS_TMC26X) \ + ENABLED(Y_IS_TMC2130) \ + ENABLED(Y_IS_TMC2208) \ + ENABLED(Y_IS_L6470) #error "Please enable only one stepper driver for the Y axis." #endif #if 1 < 0 \ + ENABLED(Y2_IS_TMC26X) \ + ENABLED(Y2_IS_TMC2130) \ + ENABLED(Y2_IS_TMC2208) \ + ENABLED(Y2_IS_L6470) #error "Please enable only one stepper driver for the Y2 axis." #endif #if 1 < 0 \ + ENABLED(Z_IS_TMC26X) \ + ENABLED(Z_IS_TMC2130) \ + ENABLED(Z_IS_TMC2208) \ + ENABLED(Z_IS_L6470) #error "Please enable only one stepper driver for the Z axis." #endif #if 1 < 0 \ + ENABLED(Z2_IS_TMC26X) \ + ENABLED(Z2_IS_TMC2130) \ + ENABLED(Z2_IS_TMC2208) \ + ENABLED(Z2_IS_L6470) #error "Please enable only one stepper driver for the Z2 axis." #endif #if 1 < 0 \ + ENABLED(E0_IS_TMC26X) \ + ENABLED(E0_IS_TMC2130) \ + ENABLED(E0_IS_TMC2208) \ + ENABLED(E0_IS_L6470) #error "Please enable only one stepper driver for the E0 axis." #endif #if 1 < 0 \ + ENABLED(E1_IS_TMC26X) \ + ENABLED(E1_IS_TMC2130) \ + ENABLED(E1_IS_TMC2208) \ + ENABLED(E1_IS_L6470) #error "Please enable only one stepper driver for the E1 axis." #endif #if 1 < 0 \ + ENABLED(E2_IS_TMC26X) \ + ENABLED(E2_IS_TMC2130) \ + ENABLED(E2_IS_TMC2208) \ + ENABLED(E2_IS_L6470) #error "Please enable only one stepper driver for the E2 axis." #endif #if 1 < 0 \ + ENABLED(E3_IS_TMC26X) \ + ENABLED(E3_IS_TMC2130) \ + ENABLED(E3_IS_TMC2208) \ + ENABLED(E3_IS_L6470) #error "Please enable only one stepper driver for the E3 axis." #endif #if 1 < 0 \ + ENABLED(E4_IS_TMC26X) \ + ENABLED(E4_IS_TMC2130) \ + ENABLED(E4_IS_TMC2208) \ + ENABLED(E4_IS_L6470) #error "Please enable only one stepper driver for the E4 axis." #endif /** * Digipot requirement */ #if ENABLED(DIGIPOT_MCP4018) #if !defined(DIGIPOTS_I2C_SDA_X) || !defined(DIGIPOTS_I2C_SDA_Y) || !defined(DIGIPOTS_I2C_SDA_Z) \ || !defined(DIGIPOTS_I2C_SDA_E0) || !defined(DIGIPOTS_I2C_SDA_E1) #error "DIGIPOT_MCP4018 requires DIGIPOTS_I2C_SDA_* pins to be defined." #endif #endif /** * Require 4 or more elements in per-axis initializers */ constexpr float sanity_arr_1[] = DEFAULT_AXIS_STEPS_PER_UNIT, sanity_arr_2[] = DEFAULT_MAX_FEEDRATE, sanity_arr_3[] = DEFAULT_MAX_ACCELERATION; static_assert(COUNT(sanity_arr_1) >= XYZE, "DEFAULT_AXIS_STEPS_PER_UNIT requires 4 (or more) elements."); static_assert(COUNT(sanity_arr_2) >= XYZE, "DEFAULT_MAX_FEEDRATE requires 4 (or more) elements."); static_assert(COUNT(sanity_arr_3) >= XYZE, "DEFAULT_MAX_ACCELERATION requires 4 (or more) elements."); static_assert(COUNT(sanity_arr_1) <= XYZE_N, "DEFAULT_AXIS_STEPS_PER_UNIT has too many elements."); static_assert(COUNT(sanity_arr_2) <= XYZE_N, "DEFAULT_MAX_FEEDRATE has too many elements."); static_assert(COUNT(sanity_arr_3) <= XYZE_N, "DEFAULT_MAX_ACCELERATION has too many elements."); #if ENABLED(CNC_COORDINATE_SYSTEMS) && ENABLED(NO_WORKSPACE_OFFSETS) #error "CNC_COORDINATE_SYSTEMS is incompatible with NO_WORKSPACE_OFFSETS." #endif #if !BLOCK_BUFFER_SIZE || !IS_POWER_OF_2(BLOCK_BUFFER_SIZE) #error "BLOCK_BUFFER_SIZE must be a power of 2." #endif #if ENABLED(LED_CONTROL_MENU) && DISABLED(ULTIPANEL) #error "LED_CONTROL_MENU requires an LCD controller." #endif #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) && DISABLED(NEOPIXEL_LED) #error "CASE_LIGHT_USE_NEOPIXEL requires NEOPIXEL_LED." #endif #if ENABLED(SKEW_CORRECTION) #if !defined(XY_SKEW_FACTOR) && !(defined(XY_DIAG_AC) && defined(XY_DIAG_BD) && defined(XY_SIDE_AD)) #error "SKEW_CORRECTION requires XY_SKEW_FACTOR or XY_DIAG_AC, XY_DIAG_BD, XY_SIDE_AD." #endif #if ENABLED(SKEW_CORRECTION_FOR_Z) #if !defined(XZ_SKEW_FACTOR) && !(defined(XZ_DIAG_AC) && defined(XZ_DIAG_BD) && defined(XZ_SIDE_AD)) #error "SKEW_CORRECTION requires XZ_SKEW_FACTOR or XZ_DIAG_AC, XZ_DIAG_BD, XZ_SIDE_AD." #endif #if !defined(YZ_SKEW_FACTOR) && !(defined(YZ_DIAG_AC) && defined(YZ_DIAG_BD) && defined(YZ_SIDE_AD)) #error "SKEW_CORRECTION requires YZ_SKEW_FACTOR or YZ_DIAG_AC, YZ_DIAG_BD, YZ_SIDE_AD." #endif #endif #endif #endif // _SANITYCHECK_H_