# Implemented G Codes ## G Codes ``` G0 -> G1 G1 - Coordinated Movement X Y Z E G2 - CW ARC G3 - CCW ARC G4 - Dwell S[seconds] or P[milliseconds] G10 - retract filament according to settings of M207 G11 - retract recover filament according to settings of M208 G28 - Home all Axis G29 - Detailed Z-Probe, probes the bed at 3 points. You must be at the home position for this to work correctly. G30 - Single Z Probe, probes bed at current XY location. G31 - Dock Z Probe sled (if enabled) G32 - Undock Z Probe sled (if enabled) G90 - Use Absolute Coordinates G91 - Use Relative Coordinates G92 - Set current position to cordinates given ``` ## M Codes ``` M0 - Unconditional stop - Wait for user to press a button on the LCD (Only if ULTRA_LCD is enabled) M1 - Same as M0 M17 - Enable/Power all stepper motors M18 - Disable all stepper motors; same as M84 M20 - List SD card M21 - Init SD card M22 - Release SD card M23 - Select SD file (M23 filename.g) M24 - Start/resume SD print M25 - Pause SD print M26 - Set SD position in bytes (M26 S12345) M27 - Report SD print status M28 - Start SD write (M28 filename.g) M29 - Stop SD write M30 - Delete file from SD (M30 filename.g) M31 - Output time since last M109 or SD card start to serial M32 - Select file and start SD print (Can be used _while_ printing from SD card files): syntax "M32 /path/filename#", or "M32 S !filename#" Call gcode file : "M32 P !filename#" and return to caller file after finishing (similar to #include). The '#' is necessary when calling from within sd files, as it stops buffer prereading M42 - Change pin status via gcode Use M42 Px Sy to set pin x to value y, when omitting Px the onboard led will be used. M48 - Measure Z_Probe repeatability. M48 [n # of points] [X position] [Y position] [V_erboseness #] [E_ngage Probe] [L # of legs of travel] M80 - Turn on Power Supply M81 - Turn off Power Supply M82 - Set E codes absolute (default) M83 - Set E codes relative while in Absolute Coordinates (G90) mode M84 - Disable steppers until next move, or use S to specify an inactivity timeout, after which the steppers will be disabled. S0 to disable the timeout. M85 - Set inactivity shutdown timer with parameter S. To disable set zero (default) M92 - Set axis_steps_per_unit - same syntax as G92 M104 - Set extruder target temp M105 - Read current temp M106 - Fan on M107 - Fan off M109 - Sxxx Wait for extruder current temp to reach target temp. Waits only when heating Rxxx Wait for extruder current temp to reach target temp. Waits when heating and cooling IF AUTOTEMP is enabled, S B F. Exit autotemp by any M109 without F M112 - Emergency stop M114 - Output current position to serial port M115 - Capabilities string M117 - display message M119 - Output Endstop status to serial port M120 - Enable endstop detection M121 - Disable endstop detection M126 - Solenoid Air Valve Open (BariCUDA support by jmil) M127 - Solenoid Air Valve Closed (BariCUDA vent to atmospheric pressure by jmil) M128 - EtoP Open (BariCUDA EtoP = electricity to air pressure transducer by jmil) M129 - EtoP Closed (BariCUDA EtoP = electricity to air pressure transducer by jmil) M140 - Set bed target temp M150 - Set BlinkM Color Output R: Red<0-255> U(!): Green<0-255> B: Blue<0-255> over i2c, G for green does not work. M190 - Sxxx Wait for bed current temp to reach target temp. Waits only when heating Rxxx Wait for bed current temp to reach target temp. Waits when heating and cooling M200 D- set filament diameter and set E axis units to cubic millimeters (use S0 to set back to millimeters). M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000) M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!! M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec M204 - Set default acceleration: P for Printing moves, R for Retract only (no X, Y, Z) moves and T for Travel (non printing) moves (ex. M204 P800 T3000 R9000) in mm/sec^2 M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk M206 - Set additional homing offset M207 - Set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop], stays in mm regardless of M200 setting M208 - Set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/sec] M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction. M218 - Set hotend offset (in mm): T X Y M220 S- set speed factor override percentage M221 S- set extrude factor override percentage M226 P S- Wait until the specified pin reaches the state required M240 - Trigger a camera to take a photograph M250 - Set LCD contrast C (value 0..63) M280 - Set servo position absolute. P: servo index, S: angle or microseconds M300 - Play beep sound S P M301 - Set PID parameters P I and D M302 - Allow cold extrudes, or set the minimum extrude S. M303 - PID relay autotune S sets the target temperature. (default target temperature = 150C) M304 - Set bed PID parameters P I and D M380 - Activate solenoid on active extruder M381 - Disable all solenoids M400 - Finish all moves M401 - Lower z-probe if present M402 - Raise z-probe if present M404 - N Enter the nominal filament width (3mm, 1.75mm ) or will display nominal filament width without parameters M405 - Turn on Filament Sensor extrusion control. Optional D to set delay in centimeters between sensor and extruder M406 - Turn off Filament Sensor extrusion control M407 - Display measured filament diameter M500 - Store parameters in EEPROM M501 - Read parameters from EEPROM (if you need reset them after you changed them temporarily). M502 - Revert to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. M503 - Print the current settings (from memory not from EEPROM). Use S0 to leave off headings. M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] M665 - Set delta configurations M666 - Set delta endstop adjustment M605 - Set dual x-carriage movement mode: S [ X R ] M907 - Set digital trimpot motor current using axis codes. M908 - Control digital trimpot directly. M350 - Set microstepping mode. M351 - Toggle MS1 MS2 pins directly. M928 - Start SD logging (M928 filename.g) - ended by M29 M999 - Restart after being stopped by error ``` ## SCARA-specific M-Codes - May change to suit future G-code standards ``` M360 - SCARA calibration: Move to cal-position ThetaA (0 deg calibration) M361 - SCARA calibration: Move to cal-position ThetaB (90 deg calibration - steps per degree) M362 - SCARA calibration: Move to cal-position PsiA (0 deg calibration) M363 - SCARA calibration: Move to cal-position PsiB (90 deg calibration - steps per degree) M364 - SCARA calibration: Move to cal-position PSIC (90 deg to Theta calibration position) M365 - SCARA calibration: Scaling factor, X, Y, Z axis ``` # Comments Comments start at a `;` (semicolon) and end with the end of the line: N3 T0*57 ; This is a comment N4 G92 E0*67 ; So is this N5 G28*22 (example taken from the [RepRap wiki](http://reprap.org/wiki/Gcode#Comments)) If you need to use a literal `;` somewhere (for example within `M117`), you can escape semicolons with a `\` (backslash): M117 Hello \;) `\` can also be used to escape `\` itself, if you need a literal `\` in front of a `;`: M117 backslash: \\;and a comment Please note that hosts should strip any comments before sending GCODE to the printer in order to save bandwidth.